Delta C200 Series AC Drives

Transcription

1 Delta C200 Series AC Drives The VFD-C200 Series is an intelligent vector control micro drive that provides versatile control modes for motors and includes built-in PLC functions with capacity up to 5,000 steps. It is suitable for harsh environment applications with a strengthened thermal and anti-dust design that provides comprehensive protection. Delta C200 Series AC Drives Specifications: Built-in PLC program with 5,000 steps capacity Built-in brake chopper MODBUS RS-485 and CANopen (Slave) The high-brightness LED keypad shares the same extension cable of the VFD-E/M/B Series to maximize operation distance Supports open loop control of permanent motors (PM Sensorless) Two high speed pulse input terminals MI7 and MI8 built-in with maximum speed up to 33kHz Two high speed pulse output terminals DFM1 and DFM2 built-in with maximum speed up to 33kHz New PCB coating for circuit (IEC class 3C2) and thermal design suitable for harsh environment applications C200 Series Frame A supports wall mounted installation Part Numbers: SKU KW HP Volts Phase Amps VDEL0.7 3/3 C VDEL1.5 3/3 C VDEL2.2 3/3 C VDEL3.7 3/3 C VDEL4.0 3/3 C VDEL5.5 3/3 C VDEL7.8 3/3 C VDEL0.4 1/3 C / VDEL0.7 1/3 C VDEL1.5 1/3 C VDEL2.2 1/3 C C200 User Manual C200 Catalogue Associate company: Rotating Machinery Supplies, 6 Devon Road, Hamilton rotatingmachinery@clear.net.nz

2 QUICK SET UP INSTRUCTIONS FOR DELTA VDF-C200 1PHASE TO 3PHASE VARIABLE SPEED DRIVE Important Notice Wiring and connection must be carried out by a registered electrician. Connection by an unqualified person voids the warranty. Please check the suitability of the motor before attempting to connect it to the device. Ensure the motor terminals are connected in a DELTA connection. Operations panel Quick Setup for Variable Speed Drive Turn on power to unit and follow as below: F60.0 will be displayed on the screen. Press the enter button. 00. will appear on the screen. Press enter again will appear on the screen. Use the up and down keys to change parameters selections to the desired one. Press enter You will now be able to change the parameter to the desired value or setting. Press enter. End will flash on your screen to indicate that your setting has been saved. Continue the above steps till all of your parameters have been set. Once all the parameters have been set press the Mode button till the F60.0 screen comes up again. C200 1/3

3 OPTIONAL IF REQUIRED List of quick set parameters Source of master Frequency Command. Set to 7 for keypad potentiometer. Factory setting is up and down buttons for speed control Change to the maximum Frequency required Change value to match Change to 230V (Max Voltage output) Mid-Point Frequency. Set to half the value of Mid-point Voltage. Set to half the value of Upper limit Frequency Lower limit Frequency Acceleration time Deceleration time Set to Motor Name Plate Current Set to Motor Name Plate KW Set to Motor Name Plate Speed Set as the number of poles of the motor. FOR ADVANCED SET UP REFER TO MANUAL AND CD ROM PROVIDED Instructions for Remote Setup (Remote On Off/ Speed Variation) For remote stop and start connect between DCM and FWD. (DCM is your common) For remote Potentiometer connect the pot to +10V, AVI and ACM (common). Set to 2 (Remote Potentiometer setting) Set to 1 (Remote ON/OFF setting) Set to 0 Connect Live to R and Neutral to S And the Motor to U,V and W C200 1/3

4 QUICK SET UP INSTRUCTIONS FOR DELTA VDF-C200 3PHASE TO 3PHASE VARIABLE SPEED DRIVE Important Notice Wiring and connection must be carried out by a registered electrician. Connection by an unqualified person voids the warranty. Please check the suitability of the motor before attempting to connect it to the device. Ensure the motor terminals are connected for 400V supply. Operations panel Quick Setup for Variable Speed Drive Turn on power to unit and follow as below: F60.0 will be displayed on the screen. Press the enter button. 00. will appear on the screen. Press enter again will appear on the screen. Use the up and down keys to change parameters selections to the desired one. Press enter You will now be able to change the parameter to the desired value or setting. Press enter. End will flash on your screen to indicate that your setting has been saved. Continue the above steps till all of your parameters have been set. Once all the parameters have been set press the Mode button till the F60.0 screen comes up again. C200 3/3

5 OPTIONAL IF REQUIRED List of quick set parameters Source of master Frequency Command. Set to 7 for keypad potentiometer. Factory setting is up and down buttons for speed control Change to the maximum Frequency required Change value to match Change to 415V (Max Voltage output) Mid-Point Frequency. Set to half the value of Mid-point Voltage. Set to half the value of Upper limit Frequency Lower limit Frequency Acceleration time Deceleration time Set to Motor Name Plate Current Set to Motor Name Plate KW Set to Motor Name Plate Speed Set as the number of poles of the motor. (3000rpm=2pole; 1500rpm=4pole; 1000rpm=6pole; 750rpm=8pole) FOR ADVANCED SET UP REFER TO MANUAL AND CD ROM PROVIDED Instructions for Remote Setup (Remote On Off/ Speed Variation) For remote stop and start connect between DCM and FWD. (DCM is your common) For remote Potentiometer connect the pot to +10V, AVI and ACM (common). Set to 2 (Remote Potentiometer setting) Set to 1 (Remote ON/OFF setting) Set to 0 Connect L1-R, L2-S and L3-T And the Motor to U,V and W C200 3/3