SDI Monitor with WIFI DVR and local DVR. MC22SDI. User s Manual Instructions

Transcription

1 SDI Monitor with WIFI DVR and local DVR. MC22SDI User s Manual Instructions 7/17/2012

2 Safety Precautions: DO NOT ATTEMPT TO DISASSEMBLE THE DEVICE. Risk of Electric Shock, Do not Open CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO A QUALIFIED SERVICE PERSON This symbol is intended to alert the user to the presence of non-insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operation and maintenance instructions in the literature accompanying the appliance. Warning! 1. This product has patented for configuration and appearance design, and copying is not permitted. 2. If this product fails to operate normally, contact authorized distributor or a service center. Never disassemble or modify the product in any way. Problem caused by unauthorized user disassembly or repairs voids the warranty. 3. Electromagnetic fields in specific frequency may cause image interference. 4. Be sure to use only the standard adapter which is specified in the specification sheet. Using other adapter could cause fire, electric shock or damage to product. 5. Connecting the power supply incorrectly may result in fire, electric shock or damage to the product as well. 6. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat causing fire. 7. Securely plug the power cord into power receptacle. Any loose connection may result in fire. 8. When installing the camera on a wall or ceiling, fasten it safely and securely. A falling camera may cause personal injury. 9. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers filled with water on top of the product. 10. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause personal injury. 11. If any unusual smell or smoke comes from the unit, please stop using the product. In such case, please immediately disconnect the power source and contact local authorized distributor or a Service Center. 12. When cleaning, do not spray water directly onto parts of the product, or may cause fire or electric shock. Gently wipe the surface with a dry cloth. Never use detergents or chemical cleaner on the products, or may cause fire or electric shock.

3 Cautions 1. Do not drop objects on the products or apply strong shock to it. Keep it away from a location subject to excessive vibration or magnetic-field interference. 2. Do not install in a location subject to high temperature (over 122 F or +50 ), or low temperature(below 14 F or -20 ), it may cause fire. 3. If you want to relocate the installed products, be sure to turn off the power before moving or reinstalling it. 4. Remove the power plug from the outlet when there is a lightning storm. Neglecting to do so may cause fire or damage to the product. 5. Avoid a location which is exposed to direct sunlight, or near heat sources. Neglecting to do so may cause fire. 6. Install in a well-ventilated location. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions for later use. 3. Pay attention that all warnings should be adhered to. 4. Follow all instruction. 5. Do not use this product near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. 8. Do not install near any heat sources such as radiations, heat registers, or other product (including amplifiers) that produce heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Only use attachment/accessories specified by the manufacturer. 11. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. 12. Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Do not operate the device beyond its temperature, humidity or power source ratings. Operating temperature: 14F-122F( ); Humidity<85%

4 Table of Contents Chapter 1 - Overview 1.1 Introduction This is a user s manual for the Camera, Monitor, DVR and WI-FI from this product. 1.2 Package SDI Monitor with DVR / WiFi DVR / SDI Camera Built-in Remote Control for the Monitor / Remote Control for the DVR Specification : 1.4 Panel Front: LCD Screen Camera REC led POWER led IR led Side:ON/OFF Switch Back Top:Reset Button,RJ45 jack,antenna input; Back (from left to right) HDMI, VGA IN, Y, Pb, Py, VIN1, VIN1.4, V Out, Audio in 1/1.4, Back Bottom:DVR SD Card, mic, mic, WiFi SD Card Remote Control : POWER:ON/OFF MUTE:ON/OFF PICTURE:MODE: ( USER T / STANDARD / L-LIGHT / H-LIGHT) FREEZE:PICTURE FREEZE INPUT:PC N/A HDMI SDI CAMERA AV SDI CAMERA LOWER RESOLUTION AV2 DVR with SD CARD YPBPr N/A MENU:MONITOR OSD MENU

5 VGA:N/A YPbPr: N/A HDMI: SDI CAMERA AV:AV S-VIDEO:N/A DVI:N/A Chapter 2 - Monitor Operation 2. 1 Start Plug the power cord, Turn the Switch ON and the GREEN LED indicator will turn on 2.2 Menu Monitor Screen Menu: (Picture, Sound, System, Advance, PIP) Picture ITEM OPTIONS CONTRAST BRIGHTNESS HUE SATURATION SHARPNESS COLOR TONE NORMAL/WARM/COOL SCALE FULL/ZOOM/ZOOM2/NORMAL/14:9 PICTURE MODE USER/STANDARD/L-LIGHT/H-LIGHT 3D NR OFF/LOW/MID/HIGH MPEG NR OFF/LOW/HIGH Sound ITEM EQUALIZER SOUND MODE SUBWOFFER SUPERBASS LOUDNESS AVC OPTIONS 120HZ/500HZ/1K5HZ/5KHZ/10KHZ USER/STANDARD/MOVIE/MUSIC OFF/ON OFF/ON/1/2 OFF/MODE1/MODE2/MODE3/MODE4 OFF/ON

6 2.2.3 System ITEM OPTIONS OSD-LANGUAGE ENGLISH/CHINESE OSD-HPOSITION OSD-VPOSITION OSD-DURATION OSD-HALFTONE MEM-RECALL Advance ITEM SLEEP-TIMER BLACK-L OPTIONS OFF/15M/30M/45M/60M OFF/LOW/HIGH H-POSITION H-CUT V-POSITION V-CUT PIP ITEM MULITI WINDOW SUB SOURCE SIZE PIP-POSITION VPOSITION BOARDERCOLOR SOUNDSOURCE SWAP OPTIONS OFF/PIP/PIP FULL AV/AV2 (PIP/PIP FULL ON) LARGE/MID/SMALL (PIP ON) (PIP ON) (PIP ON) BLUE/BLACK MAIN/SUB

7 Chapter 3 WIFI / IP DVR Operation 3.1 IP/WIFI Camera/DVR / Configuration System Requirements: - Internet Explorer 6.0 or above - DirectX 9.0 or above Client Network Settings: Note: Your computer must be in the same network address range with the video server to communicate, therefore you may need to change the IP address of the video server before you can login to the server. Please follow these instructions: Step 1: Install the Network Video Client Software Insert the software disk to the CD-ROM, you will see the NVClient Software installation file, run the program. After the installation, click Start Programs Digital Video Management Center then run Server Tools V2 as follows Step 2: Click search to search the video servers, choose the server and click Modify Net, a dialog will show up as below:

8 Step 3: Modify the IP address (example: modify the address to ), see the example below: 3.2. Video encoder login and Interface function description Login the video encoder via the NVClient software Steps of login Step 1: add an IP address to computer so as to access DVS/IP Camera, for example: Step 2: Login client side, in Windows operating system, click Start Program Digital Video Management Center menu, click NVClient, type user name admin, password admin then press OK to enter to the program.

9 Click on Local Setup on the menu bar: Please follow the steps below to add a DVS/IP Camera into a local LAN: Click Search button to locate the IP of the device.

10 Step 1: select the device to be added in the search list Step 2: click on Add button.

11 Step 3: Type Local Name defined by user. Enable auto login server, when you login the server next time, you won t need to retype a username and password. Step 4: After the setting are done, return to the main page of the software, double click the added device in the device list, and then double click the channel below the device to see the video. 3.3 Login the video encoder via Internet Explorer Step 1: Run the IE, type-in the IP address of the server in the address line e.g. as shown below, the system will ask for permission to install the plug-in

12 Step 2: If this your first time to login, please click download link: Click here to download and install the ActiveX packet manually. a dialog will pop up as below: Step 3: Click button, a dialog will pop up as bellows:

13 Step 4: Click button and button to finish install. Step 5: Input username and password and then click button. Note: the default login is admin, password is admin Step 6: Click button to open video channel.

14 3.4 Web client Interface function description Click this button to open or close channel picture. Click this button to carry out snapshot to front end video. Click this button to enable talkback function with front end DVS/IP Camera. Click this button to enable talkback function with front end DVS/IP Camera. Click this button to switch between audio enable and disable. Click this button to enable rain strip function. Click this button to enable lighting function. N/A for this model

15 N/A for this model N/A for this model Click this menu to switch to real time preview interface Click this button to switch to record playback interface Click this button to pop up parameters setting diagram Click this button to exit login 3.5. Video Decoder login and configuration Decoder default network parameter: IP Address: Subnet mask: Default gateway: DNS server:xxx.xxx.xxx.xxx Decoder login Login steps: Step 1: Run NVClient in the Start Program Digital Video Management Center menu, input username and password to login the system. Step 2: Select Login Server, input username and password.

16 Step 3: Input the username and password (default value are admin), click Ok Decoder configuration Enters the parameter Setting three methods: Method 1: Select the decoder after login, select Set ting Configuration with right key Method 2: Select the decoder after login; click the button on the main menu to pop up the remote configuration window Method 3: Select the decoder after login, press F5 key Channel setting Enters the parameter setting and select the Camera Setup, which encoder can connect the decoder in here you to have to connect. Step in the Setting Configuration and select the Camera Setup, then you can set which encoder the decoder could connect.

17 Alone Alone: Only connects an encoder the image. If is the multi-channel video frequency encoder may choose the random channel decoding output also to be possible to choose an encoder all channels simultaneously to decode the output; Enable Auto Connect: Auto connect to encoder; Address: input encoder domain address for the domain or the encoder IP address for the IP Add. Port: input the decoder port Username, Password: input the username and password for decoder login Channel: Which channel connects the encoder. If is the multi-channel network video frequency encoder may choose al l channels, realization multi-channel video frequencies by picture division way output; After above parameter establishment correct, then clicks on [connection] the button to connect the corresponding encoder, if wants to separate the connection click [separation] then Cycle Cycle: May connect the multi-taiwan encoder, according to establishment time-gap circulation cut decoding output; This company's decoder are most may support 16 group circulation decoding output,steps:

18 Step 1:Select Cycle ; Step 2:Double click Info (1 16), and clicked; Step 3:Choice Address in Connect Info : Domain or IP Add ; Step 4:Input the message Server Add,Port,User Name,Password,Channel of the DVS which needs to connect; Step 5: Switch Times.Input the time of the circulation show. The minimum value is 10S; Step 6:After the above establishment completes, clicks Modify ; Step 7:Continues to increase other circulation server address; Step 8:Click Cycle Connect.Ok, save to FLASH Access camera on the WAN (INTERNET) Step 1: Make sure the DVS IP address is LAN IP address; make sure the IP address and the DNS server are correct and are on the same IP structure.

19 (Router LAN IP address) Step 2: Setting Virtual Server on the rooter (DVS Network Setting)

20 (Setting Virtual Server, Web Port: 80, add DVS IP address: ) (Setting Virtual Server, Data Port: 8200, add DVS IP address: )

21 Step 3: Get WAN IP address ( ) then enter this address to browser. Example:

22 3.7. Network DVR FAQ 1) Question: unable to access the network video encoder Check the network video encoder, PING to see if the IP is online. Check the IP address, port number, user name, password on the Video Server. And also if the Router and the Video Server are on the same IP structure. E.g XXX 2) Question: It is connected but no Video Check the video connection, and also if the camera has power and the Lens are not obstructed by any object. 4) Question: No Video via Internet Browser Check the network connection Ping the IP Possible reason: IP address conflict Solution: Disconnect the Video Server from the LAN and reconnect to the PC and Reset the IP address. Look for a different IP address that won t conflict with any other device in the Network. Possible reason: IP address in different subnets Solution: Check the IP address and subnet mask of the server and gateway Possible reason: web port is changed Solution: Contact network administrator to obtain a port information Possible reason: unknown Solution: Reset server to the factory settings and re-connect to the network. The default IP address of system is (Default IP address of decoder system is ) Default parameters Network parameters 1) Network Video Server and IP Camera default parameters Parameters Default IP address Subnet address

23 Gateway Data port 8200 Web port 80 Mobile port UPNP Off 2) Network Video Decoder default parameters Parameters Default IP address Subnet address Gateway Data port Username and password Parameter Username Password Default admin admin Chapter 4 - SD Card Storage DVR 4.1 Remote Control for the DVR with SD CARD

24 .2 Live Mode Live mode is the default setup after system start-up. Time Display: System Date and Time. Button Lock: Indicates all buttons are locked (buttons are ineffective). Video Status: Indicates external camera connection.

25 Record Size, please refer to 6.4 Record Setup for VIDEO SIZE setup. Record Quality, please refer to 6.4 Record Setup for VIDEO QUALITY setup. Audio Off Record, please refer to 6.4 Record Setup for AUDIO RECORD setup. SD Card Status: SD Card has not been inserted or there is an error. SD Card is conducting file testing. SD Card is functioning normally. Overwrite record. When SD card is not inserted, record and playback function is not operational, but monitoring is operational. 4.3 Record Mode 1. Start Record: 3 Types of recording mode. (1) Manual Record: Suitable to record at anytime. Press (REC) Button, to enter manual recording status (start recording). For more information, please refer to 6.4 Manual Record & Schedule Record. (2) Motion Detection Record: Suitable to record, when there are severe image changes. Motion detection triggers schedule recording, but it will only start recording when the variation exceeds the alarm limitation value. For more information, please refer to 6.3 Motion Detection and 6.4 Manual Record & Schedule Record. (3) Continuous Record: Suitable for few constant frame recording or on long-term continuous recording. For more information, please refer to 6.4 Manual Record & Schedule Record. (4) Alarm Record : Suitable for external alarm recording. When alarm schedule been setup, alarm icon will be shown on the display status bar (alarm triggered recording is setup). 2. Stop Record: Manual Record Press (STOP) button/ Manual Power-Off/ Auto Power-Off when System Power Shortage. Schedule Record To Stop Schedule Recording, Press ( MENU/ OK), select (schedule record), (schedule setup) and turn the function OFF. To continue recording, please follow the methods below to restart recording. Manual Record Press (REC) Button Schedule Record Stop playback and the system will auto resume recording.

26 Record Status: : Indicates recording is in progress. Record Mode: Manual Record Schedule Record Motion Detection Record Alarm Record Record Storage Mode Status: Continuous Record % Remaining Storage Capacity 4 System recording is determined according to the recording priority order (Record Priority: Manual/ Alarm/ Motion Detection/ Continuous). 5. Different recording modes may have different kinds of setups. Basic setup: video size, recording frames, video quality, and audio recording. When different recording modes are triggered, the system starts recording according to the different setup. This kind of design provides flexibility to ensure efficient recording time and quality. Example: Work hour from 8:00am to 6:00pm, setup Schedule Record to low video quality with less recording frames to extend the recording time. And off work hour, setup Motion Detection Record/ Alarm Record to enable high video quality with the highest recording frames, when an event occurs. 6. Video or audio may be recorded into the SD card (SD card is purchased separately). Do not withdraw the SD card while recording. It may destroy the data stored within the SD card. Power loss during recording can result in incomplete videos or errors. I f video is lost during recording, the system will stop recording, backup the files, and will continue recording only after video signal is restored.

27 according to the SD card file recording order. (PLAY / PAUSE) Button to first playback the final recorded data, and then Playback Status: Press (PLAY/PAUSE) Button once to playback, press it again to pause. Press directional buttons to Fast Rewind or Fast Forward (Speed: x2/ x4/ x8/ x16/ x32). Press (PLAY/PAUSE) button to return to normal speed playback. During playback, press (PLAY/PAUSE) Button to pause playback and press again to return to playback status. During pause, press directional buttons to step back one frame or to step forward one frame and press (PLAY/PAUSE) button to return to normal speed playback. Press (ESC/STOP) button to stop playback function and to return to live status. (2) Search and Playback: Enter MENU and select SEARCH AND PLAY item. File directory shows dates and the amount of contents under the directory. The user may press Directional buttons to move the cursor up or down. Current location page.

28 Event Record Status Icon: Manual Motion Detection Continuous Alarm (NOTE 1 & NOTE 2). Each color distinguishing different recording events, the user may press directional buttons to move the cursor left or right and immediately shows the first image of the highlighted event on the screen display background. Displays the time highlighted by the event bar. Select the starting point and press (MENU/OK) button to playback. Press (ESC/STOP)button to stop playback and the system will return to (SEARCH and PLAY) selection and enables the user to select the prefered input source. NOTE 1 NOTE 2 The device supports playback only to images recorded by our device, other ASF video files are not guaranteed. 4.5 PC Playback 1. The device uses SD card as its main storage. You may read the data stored in the SD card from other computers that support SD card reader devices. 2. All files (under DVMPG4 folder) has approximate size of 1MB and file names are ordered according to recorded times (sequence). File Playback: User may use Microsoft Media Player or DivX DivX Player ( to playback video files. When first time using Media Player to playback, it requires the most updated decoder from the Microsoft? software website. 4.6 SD Card Maintenance 1. The device supports only FAT16/ 32 file system; therefore it is unable to determine other file systems. Please format the SD card (enter MENU/ SD CARD OPTIONS and select Format ). 2. The system supports only partial SD card file system repair. The system is unable to detect any file system damage, therefore please format the SD card (enter MENU/ SD CARD OPTIONS and select Format ). 4.7 How to Download the Updated Software 1. Use the SD card to update your system firmware. 2. Please follow the steps below to update the software: (A) Copy the new system firmware into the new directory of the SD card from your computer. (B) Insert the SD card; switch off the main power and then restart. (C) Wait for 5 to 6 seconds, the system update will be complete and return to live mode. Do not extract the SD card while booting, if power-loss occurs while downloading, proceed to steps B and C.

29 6. MENU SETUP 5.1 Main Menu MAIN MENU: Item subject. Menu Layer Indication: The device consists of three menu layers. : First Menu Layer (Main Menu) : Second Menu Layer : Third Menu Layer MENU Content: Basic Menu Operations. Use the directional buttons, to select the item. Press (MENU/OK) button, to enter the sub menu Press (ESC/STOP) button: Under second or third menu layer, the system will return to the previous menu layer (second layer to first layer or third layer to second layer). Under main menu (first menu layer), the system will enter live mode. Press directional buttons, to increase or decrease the setting value of the item selected (NOTE 1). NOTE 1: All words underlined and bold indicates Default Value.

30 Date Format Y / M / D M / D / Y D / M / Y Date/ Time Adjustment Year Setup: Month Setup: Time Setup: 00 : : 59 Return to factory default, no changes will be made. 5.3 Motion Detection 1. Window Setup: Detection Block: Formed by two or more cells. Cursor: Press (MENU/OK) button to switch to Select / Edit Mode. Detection Cell: The whole screen is divided into 16x12 cells. Detection Block. 2. Cursor Movement: Press (MENU/OK) button to switch to setup mode (cursor color is black). press directional buttons to move the cursor freely.

31 MD ENERGY Reveals current sensitivity rate (NOTE 1). MD THRESHOLD Reveals user sensitivity rate setup. Press directional buttons, to change the motion detection threshold level (NOTE 2). NOTE 1: Motion detection is triggered when MD ENERGY level exceeds MD THRESHOLD level (red block). NOTE 2: The red cells reveals the setup made by the user.

32 5.4 Record Setup Selectable manual or schedule recording, basic setups are shown below: 1. MANUAL RECORD: Press (REC)button to start recording (NOTE 1). Video Size/ Frame Rate Setup: VIDEO SIZE 320x x480 FRAME RATE (MAX) 30 fps 12 fps Image Quality: HIGH Using high recording quality (More CF card storage capacity will be required). MEDIUM Using medium recording quality. LOW Using low recording quality (Less CF card storage capacity will be required). Audio Record: Enable or disable audio recording. NOTE 1: Menu setup is inapplicable during manual recording. 2. SCHEDULE RECORD (Alarm Detection/ Motion Detection/ Continue): Records only within the setup time range. SCHEDULE SETUP ALARM RECORD MOTION RECORD CONTINUE RECORD Enable/ Disable schedule and record mode setup. Alarm setup. Motion detection setup. Continuous setup.

33 SCHEDULE SCHEDULE MODE Record ON / OFF setup (default setup is OFF). Press directional buttons to setup schedule time and to setup different types of recording schedule. ( Motion Detection Record Continuous Record Alarm Triggered Record). (2) Increase setup during Alarm Detection: DURATION Duration time when motion detection has been triggered (05 ~ 90 SEC (increase by every 5 SEC) / 10 SEC). ALARM INPUT Alarm trigger method (N.C./N.O.). (3) Increase DURATION setup during Motion Detection Record: CONTINUOUS RECORDING Continuous recording time when motion detection has been triggered (05 ~ 90 SEC (increase by every 5 SEC) / 10 SEC).

34 (4) CONTINUE RECORD: Setup method is similar to manual record setup, for more information please refer to [ MANUAL RECORD]. 5.5 SD Card Options TOTAL SPACE REMAINING SPACE SD card total capacity. SD card remaining capacity. NOTE 1: For continuous recording, old videos can be deleted and overwritten. Please confirm before setup. NOTE 2: Recording time depends on the SD card capacity, different recording modes, and the degree of video variation.

35 5.6 System Status Press any button to return to the Main Menu. 5.7 Power On Setup LANGUAGE Setup menu language. COMPOSITE Setup video output format, NTSC/ PAL (NOTE 1). NOTE 1: Once camera is connected, the device automatically will detect the NTSC/ PAL video system (the output video system will be set up the same as its input video system). If camera is not connected, the video system setup will be the same as its previous setup.

36 5.8 Factory Default Press (MENU/OK) button, returns all settings to the factory default value ( NOTE 1). Press (ESC/STOP) button, exit this screen display and returns to the Main Menu. NOTE 1: Returning to factory default will erase all previous selected configuration values. Except for date /time set up, Please confirm your selection before you proceed.

37 7. TROUBLE SHOOTING Q1. What is the recording capacity for a 4GB SD card? A1. Different recording setup has different recording capacity. The table below shows possible recording time during continous recording with different record modes. Quality Frame Rate SD Card High Medium Low VGA (640 x 480) 12 FPS 4 GB 10h 20min 18h 36 min 26h 36 min QVGA (320 x 240) 30 FPS 4 GB 10hs 25h 20 min SD CARD Video MPEG4 4GB 8GB 8 Hours 640 x Hours 640 x hs SD CARD Video MPEG4 16GB 32GB 32 Hours 640 x Hours 640 x 480 Q2. Why does the system automatically reboot during normal operation? A2. It indicates that the SD card has detected an error. To ensure data is recorded properly, the monitoring procedure will reboot the device. The system will return to the status prior to the error after the reboot (Ex.: returns to Manual Record or Schedule Record). Q3. Why won t the drag scroll work when playing back on the PC? A3. To solve this problem, please download AsfTools (

38 Chapter 5 - Monitor Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solves the problem, unplug the monitor and consult an authorized dealer or service center. Problem Solutions No power Firmly insert the power plug. No picture with the power on Connect the signal cable firmly. Turn on the power of the connected component and set the output correctly. Select the correct input with INPUT SELECT buttons. Check if the input signal format is acceptable to the monitor. No sound Connect the signal cable firmly. OTHERS or Out of range appears. Turn on the power of the connected component and set the output correctly. Adjust the volume level. Deactivate the muting function. Check if the input signal format is acceptable to the monitor. NO SYNC appears. Connect the signal cable firmly. Select the correct input with INPUT SELECT buttons. Turn on the power of the connected component and output video signals. Or, check if the video output of the component (video output setting of the VCR or graphic board of the computer) is set correctly. Wrong color, no color Adjust the each picture adjustment knob on the front panel or The picture becomes blurred. Wrong picture position, wrong picture size. adjust the items of PICTURE SUB ADJ. in the set-up menu. Or, perform r eset in PICTURE SUB ADJ. Select the proper color system ( COLOR SYSTEM ) in PICTURE FUNCTION. Adjust the items of WHITE BALANCE SET. in the set-up menu. Or, perform r eset in WHITE BALANCE SET. Adjust the picture contrast or brightness by using the adjustment knobs on the front panel. Or, adjust CONTRAST or BRIGHT of PICTURE SUB ADJ. in the set-up menu. Also, adjust the Camera s Lens. Adjust the picture size (H SIZE/V SIZE) or position (HPOSITION/V POSITION) of SIZE/POSI. ADJ. in the set-up menu. For some signals, the picture cannot be displayed fully in the effective screen area. There is no sure method to solve this problem.

39 Some items do not appear on the menu. Check if the input signal format is acceptable to the monitor. The items which are not available for the current input or the current input signal are not displayed on the menu. Change the input or the input signal. Chapter 6 - Monitor Current Maintenance In use of the device, regularly clean the dust and dirt on the lens surface of the screen to keep good clarity of image. Clean the device with dry and soft cloth. For stubborn dirt, please wipe it with a cloth dipped in a little neutral detergent, and then dry the device with cloth. Be careful not to use harsh chemicals such as thinner, alcohol, benzene or pesticide, etc. to clean the device, that can damage the surface coating, and even weaken the function and performance of the device.