Operation Manual. Multi Voice File PV-632

Size: px

Start display at page:

Download "Operation Manual. Multi Voice File PV-632"

Paulina Johnston
6 years ago
Views:

1 Operation Manual Multi Voice File

2 Welcome A personal welcome to you from the management and employees of Inter-M All of the co-workers here at Inter-M are dedicated to providing excellent products with inherently good value, and we are delighted you have purchased one of our products. We sincerely trust this product will provide years of satisfactory service, but if anything is not to your complete satisfaction, we will endeavor to make things right. Welcome to Inter-M, and thank you for becoming part of our worldwide extended family! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION:To prevent electric shock do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. Attentions: Pour prévenir les chocs électriques ne pas utiliser cette fiche polarisée avec un prolongateur, une prise de courant on une autre sortie de courant, sauf si les lames peuvent étre insérées à fond sans en laisser aucune partie à découvert. *Do not install this equipment in a confined space such as a book case or similar unit. *The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such vases, shall be placed on the apparatus. *WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING-WATER AND MOISTURE: Unit should not be used near water(e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so than objects do not fall and liquids are not spilled into the enclosure through openings. *CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. * It can be heated up if you use this product in closed box or ill-ventilated place.

3 Contents Unpacking...2 Installation Environment...2 Important Safety Instructions...2 Features...3 Front Panel...4 Rear Panel...6 Operation...7 Applications...9 PC and RS-232C Connection...10 Block Diagram...11 Specifications...12 Service Procedures...13 Schematic...13 Parts List...13 Variations and Options...13 Warranty

4 Unpacking Although your is neither complicated nor difficult to operate, we recommend you take a few minutes to read this brief manual and familiarize yourself with the important information regarding product features, setup and operation. As with most electronic devices, we strongly recommend you retain the original packaging. In the unlikely event the product must be returned for servicing, the original packaging (or reasonable equivalent) is required. Installation Environment Never place this product in an environment which could alter its performance or reduce its service life. Such environments usually include high levels of heat, dust, moisture, and vibration. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. S3125A 2

5 Features - REPRODUCTION METHOD AND SOUND QUALITY Can reproduce and record high sound quality of sound source by using 256kbps transmission rate on MP3 method. - STORAGE CAPACITY can record sound for a long time by adopting the built-in flash memory up to 1Gbyte. (100Mbyte or so is capacity required for operating the system. Total file capacity for downloading from a PC or recording should not exceed 900Mbyte when using.) Scalability of saving capacity is excellent with outside USB memory interface. - INTERFACE FUNCTION WITH A PC USING THE USB TERMINAL This product can perform interface with a PC through USB communication and it is easy to upload and download MP3 files from a PC. - DISPLAY FUNCTION Various functions can be indicated by adopting vacuum fluorescent display on the dot matrix box. - ENTRY FUNCTION It is convenient to record since there is an entry terminal of CD, AUX, MIC on the front and rear side. 3

Front Panel 1. USB PORT This is a terminal used for uploading or downloading MP3 files from a PC by connecting an USB cable, or operating this unit with USB memory mounted.

6 Front Panel 1. USB PORT This is a terminal used for uploading or downloading MP3 files from a PC by connecting an USB cable, or operating this unit with USB memory mounted. In connection with a PC with an USB cable, no function buttons operate, to play stored files, remove the cable connected to a PC. NOTE : For mounting the USB memory, function buttons operate for USB memory and it cannot play files contained in the built-in memory. To play files stored in the built-in memory, remove the USB memory. 2. I I (SKIP DOWN/UP) BUTTON This is a button to select previous or next file during play. 3. II (PLAY/PAUSE) BUTTON Pressing this button one time will cause the unit to PLAY the voice or music selection. Pressing this button a second time will PAUSE the unit. 4. (STOP) BUTTON Pressing this button will cause the unit to discontinue play or record operations. 5. REC/PAUSE BUTTON This is used for recording or pause. 6. REPEAT BUTTON This button is used when repeatedly playing files. 7. DELETE BUTTON This button is to delete files stored in memory. Press the DELETE button and then select a file to delete with the I button, the relevant files are deleted. I button. If pressing the ENTER 4

7 8. ENTER BUTTON This button is used in conjunction with the DELETE button to remove files from memory. 9. DUAL FUNCTION LEVEL INDICATOR While recording, the meter shows the Input signal level. During playback the meter shows the output signal level. 10. INPUT LEVEL VOLUME The position of this control knob determines the strength of the input signal while recording (amplitude is shown on the LED level indicator bar graph). Turning the knob clockwise will increase the level, turning it counter-clockwise will decrease the level. 11. STATUS DISPLAY This window displays various operation information of this unit. 12. HEADPHONE OUTPUT JACK Headphones can be connected to this jack to monitor the sound during record or playback modes. 13. MIC INPUT JACK The input accepts a 1/4 balanced (or unbalanced) microphone (for recording a voice message). 5

8 Rear Panel AC CONNECTOR AND FUSE HOLDER Connect the supplied standard AC input cable to this input. The fuse holder below the input contains the AC overload protection fuse. If the fuse has blown out, replace it with a fuse of the same type and rating. If the fuse continues to blow, refer servicing to a qualified service technician. 2. DC INPUT TERMINALS This is a DC +24V power input terminal to operate this unit by connecting with DC power. Make sure to check voltage and (+), (-) polarity before connection. 3. SERIAL PORT (to PW-642) This is a terminal to connect with our product PW-642 and can control this unit according to schedule memorized in PW-642. A distance capable of stably transmitting or receiving data using RS-232C communication method is maximum 15M. 4. CD INPUT JACK This input accepts a compact disk player (or other unbalanced line-level source) for the purpose of recording (storing) an audio program signal. 5. AUX INPUT JACK This input accepts a cassette deck (or other unbalanced line-level source) for the purpose of recording (storing) an audio program signal. 6. OUTPUT (BALANCED) This output connects to a paging system (or sound system) that will broadcast the selected audio program signal(s). 6

9 Operation 1. Play / Pause This function to play or pause files stored in memory. 1) Press the PLAY button ( II) after selecting file number with the (I I) button to play files. 2) PLAY or NEXT button is played if pressing the (I I) button during play. 3) Press the ( II) button once during play to pause, and press the button once more to stop. 4) Press the ( STOP) button to stop. 2. Recording Function to record sound source from CD, Deck and tuner, etc. 1) If pressing the REC/PAUSE button, RECORD WAITING is displayed on the display window and a REC/PAUSE button LED flashes to nodify it is ready to record. 2) If ready for recording is completed, RECORD PAUSE is displayed on the display window. 3) If pressing the REC/PAUSE button again, recording time is displayed on the display window while starting to record. 4) If pressing the REC/PAUSE button to pause during record, RECORD PAUSE is displayed on the display window. 5) If pressing the REC/PAUSE button once again, Recording continues to proceed. If using this method, you can make a sound source file by recording the desiring portion. 6) Pressing the ( STOP) button will terminate recording. 7) If pressing the PLAY ( II) button after termination, recording is played from the part last recorded. 3. Delete This is a function to delete files saved in memory. 1) To delete, press the DELETE button and select a file with the (I I) button and then press the ENTER button in order to delete. 2) To cancel DELETE, press the ( STOP) button. 3) If all music saved in memory are deleted, NO FILE is displayed on the display window. 4. Repeat This function allows you to repeatedly play files during play. 1) REPEAT OFF The unit stops after playing a file if playing the file with REPEAT turned off. 2) REPEAT REPEAT is displayed on the display window and a file during play is loaped repeatedly if pressing the REPEAT button once. 3) REPEAT ALL REPEAT ALL is displayed on the display window and all files during play are repeated if pressing the REPEAT button twice. 7

10 5. Upload / Download (MP3 File) This is interface function to connect a PC with this unit, to upload or download MP3 files from a PC. 1) If connecting a PC with the SUB port on the front of this unit using USB cables, a PC automatically recognizes it (WINDOWS 2000, WINDOWS XP). USB DEVICE is displayed on the display window of this unit in this time and a mobile disc driver appears. (Length of USB cable is maximum 2M.) 2) You can upload, download or delete MP3 files by double-clicking a movable disc. NOTE 1 : If OS is based on WINDOWS 98, you must install a separate USB driver. For the relevant USB driver and installation manual, you can download them from our homepage ( NOTE 2 : 4 folders are automatically created in the INTER-M folder of the inner memory when recording, and this folder is the part used by operation program. To use a folder in this product, do not use a INTER-M folder not create a separate and different folder to use. NOTE 3 : To remove the cable connected to a PC and this unit, first stop a Large capacity USB storage using SAFELY REMOVE HARDWARE program from a PC, and remove the cable after checking message for safely removing hardware. If failing to use such procedure, working data and product may be damaged. 8

11 Applications The shape of outlets can be different according to country requirements. 9

12 PC and RS-232C Connection 10

13 8x8 MULTI AUDIO VOICE MATRIX FILE Block Diagram 11

14 Specifications Communication Method Rated Output (1kHz) RS-232C 0dB / 2kΩ Frequency Response (Output at Rated 3dB) Input Sensitivity /Impedance AUX IN CD IN MIC IN AUX IN CD IN MIC IN 80Hz~15kHz 80Hz~15kHz 150Hz~10kHz -50dB / 47kΩ (BAL) -10dB / 47kΩ (UNBAL) 0dB / 47kΩ (UNBAL, L+R) Residual Noise (20kHz LPF) Head Phone Output(1kHz) Operation Temperature Power Source Power Consumption Weight (SET) Dimensions (SET) -80dB / 2kΩ -10dB / 47Ω -10 C ~ +40 C VAC or VAC; 50/60Hz (Supplied AC mains transformer depends on country requirements) 10W 5.5kg / 12.1lb 482(W)x88(H)x380(D)mm / 19(W)x3.5(H)x15(D)in * Specifications and design are subject to change without notice. 12

15 Service Procedures Take steps to insure the problem is not related to operator error or other products within the system. Information provided in the troubleshooting portion of this manual may help with this process. Once it is certain that the problem is related to the product contact your warranty provider as described in the warranty section of this manual. Schematic A Schematic is available by contacting your warranty provider. Parts List A Parts List is available by contacting your warranty provider. Variations and Options Variations Variations of this product exist to reflect the variations in AC power requirements throughout the world. Product supplied through local sources are compatible with local AC power requirements. Options No optional items are available for this product. Warranty Warranty terms and conditions vary by country and may not be the same for all products. Terms and conditions of warranty for a given product may be determined first by locating the appropriate country which the product was purchased in, then by locating the product type. To obtain specific warranty information and available service locations contact Inter-M directly or the authorized Inter-M Distributor for your specific country or region. 13

16 Inter-M, Ltd. (Korea) began operations in Since then, Inter-M has grown to become one of the largest manufacturers of professional audio and commercial sound electronics equipment in the world. Inter-M has gained worldwide recognition for its own branded products, as well as private label manufacturing of electronics sold under other names (OEM). The company is no longer just a Korean company, but rather a global company that is truly international in scope, with factories and offices in Korea and China, and sales and marketing operations located in Japan, Europe, and the U.S.A. With more than 850 employees around the globe, Inter-M is well-poised for further growth and expansion. Inter-M Americas, Inc Artesia Blvd. Cerritos, CA USA TEL : , FAX : Home Page : info@inter-m.net Inter-M Corporation Seoul OFFICE:653-5 BANGHAK-DONG, DOBONG-KU, SEOUL, KOREA TEL : ~8, FAX : Home Page : overseas@inter-m.com MADE IN KOREA September

Operation Manual. Program Distributor PO-6106

Operation Manual. Program Distributor PO-6106 Operation Manual Program Distributor PO-6106 * Rack mount products in the Western Hemisphere(North America, South America, and the Caribbean) do not have handles installed due to customer preference. Welcome