ANDROID DRO PRESENTED BY RICHARD DOUGLAS DESIGENED BT YURI KRUSHELNYTSKIY YURISTOYS.COM

Transcription

1 ANDROID DRO PRESENTED BY RICHARD DOUGLAS DESIGENED BT YURI KRUSHELNYTSKIY YURISTOYS.COM

2 OVERVIEW Android DRO consists of three functional components: A free Android app called TouchDRO that provides the user interface A scale interface controller that reads the raw input from the scales and sends it to the app A set of scales/position encoders attached to the machine that provide the position to the controller

3 Decoupling the driver and the display unit has several benefits: The hardware is much simpler, making the DRO much more accessible to people without electronics experinces The DRO uses a wireless (Bluetooth) link between the controller and the tablet, so the latter can be easily moved around. Therefore single Anroid tablet or phone can be used with multiple controllers. For example, if you have a milling machine and a lathe, you can share the display between the two. More controllers can be designed to support other types of scales without any changes to the display unit Since many people already have a device running Android OS, the total cost of the DRO (excluding the scales) can be as low as $30 Even the low-end Android tablets have gobs of processing power and memory (when compared to microcontrollers tha are accessible to the hobbyists), the tablet can easily support advanced features that would be unavailable on an "embedded DRO

4 TOUCHDRO APP Runs on an android device Available from Google Play or Amazon App Store

5 INTERFACE CONTROLLLER Arduino Basic DRO Controller(development discontuned) MSP430 LaunchPad Basic DRO Controller MSP430 LaunchPad Mixed Scale DRO Controller MSP430 LaunchPad Quadrature DRO Controller

6 SCALES 21-bit scales,i.e. igaging/accuremote/shahe Remote DRO Sylvac 24 bit scales, AKA "Standard Chinese Scales igaging "SPI" protocol used by igaging AbsoluteDRO+ Chinese calipers that use BIN6 protocol, i.e. common Harbor Freight digital calipers and alike Glass DRO Scales, such as Ditron, Easson, etc. Magnetic scales that provide quadrature signal

7 MSP430 CONTROLLER

8 SPECIFICATIONS Microcontroller Clock Frequency MSP430G MHz Supported Scale Format 21 Bit (Shahe/iGaging Remote DRO and AccuRemote) Supported Axes 4 Tachometer Support Scale Refresh Rate Yes (directional) 10 Hz (90KHz clock cycle) Tachometer Refresh Rate 1 Hz Position Update Rate UART Speed 10Hz 9600 Baud

9 Pros Less expensive than the Arduino version Simpler to build Low power consumption Easily upgradeable to Mixed Scale or Quadrature version Cons MSP430 Launchpad is [mostly] sold online, and might be difficult o source in some parts of the world Firmware upload process is less user friendly

10 BUY A CONTROLLER igaging supports 21-bit igaging DigiMag, AccuRemove and Shahe scales, as well the new igaging AbsoluteDRO Plus scales Quadrature - supports glass/magnetic scales and other quadrature encodes (double and single ended) Mixed Scale Kit - supports most common types of capacitive scales

11 COST igaging $79.00 Quadrature - $89.00 Mixed Scale Kit - $56.00

12 BUILD A CONTROLLER Arduino Basic DRO Controller (development discontinued) MSP430 LaunchPad Basic DRO Controller MSP430 LaunchPad Mixed Scale DRO Controller MSP430 LaunchPad Quadrature DRO Controller

13 PARTS LIST TI MSP430 Value Line Launchpad kit BlueTooth Transceiver Module USB Phone Charger Terminal Connectors (optional) Battery Holder (optional) Project Box Diodes (optional) Capacitors (optional) Wire

14 FLASHING MSP430 Connect microcontroller to computer with USB cable Download flash program from TI Place all files including Touch DRO program in the same dictrectory msp430flasher.exe -n Unknown -w "tihex.txt" -v -g -z [VCC] pause

15

16 TOOLS Soldering Iron and solder Wire Cutter and Striper

17 SCALE AND SENSOR CONNECTIONS X/Y/Z/W Clk/A - clock line input for capacitive scales using igaging (21-bit), BIN6, 7 BCD and Sylvac (2x24) protocols; A channel input for quadrature encoders. X/Y/Z/W Data/B - data line input for capacitive scales; B channel input for quadrature encoders. Tachometer A/B - input lines for a directional tachometer that uses square quadrature signal. For non-directional tachometer the firmware will simply count pulses per second on the A line, so B channel can be left disconnected. Edge probe - input line for an normally-open edge probe.

18

19 DATA CONNECTIONS Each UART port has two lines: Rx and Tx Standard connection scheme is Rx->Tx and Tx->Rx. Since the firmware only uses one-way communications with the application, only MSP430 s Tx pin needs to be connected to the adapter s Rx.

20

21 POWER CONNECTIONS 5V voltage available at TP1 comes straight from the Mini-USB connector There is no on-board 5V regulator. Make sure to use a clean and tightly regulated 5V power supply or might end up frying a set of expensive scales.

22

23

24

25

26

27 BUILD COST Launchpa d $19.99 Bluetooth $9.99 Enclosure $7.31 Capacitors $6.00 XLR Conectors $6.00 Battery Holder $1.25 Diodes $1.50 Power Supply $4.91 LED $3.50 Sheilded USB $9.99 Total $66.44

28

29

30

31

32 SCALE CALIBRATION Set display format to show four digits after the decimal period (in inch mode). Set CPI for the axes you intend to calibrate to If W axis is used, make sure it s value is displayed separately, not summed up with another axis.

33 Move the table by a number of whole inches (i.e. 5, 10, 20, etc.), By using the dials or a ground block ( i.e block) to gauge the distance. Write down the displayed readout for the axis, ignoring the decimal point. I.e. pretend the decimal points isn t there. Divide that number by the number of inches traveled. Navigate to the Axis CPI setting for the axis in question and enter the number into the CPI. Return to the DRO screen and verify that the readout display the number of inches the table traveled. Repeat for each axis.

34

35

36

37

38

39

40 THINGS LEARNED T