Monitor Performance. Before You Begin CHAPTER
|
|
|
- Shana West
- 6 years ago
- Views:
Transcription
1 CHAPTER 9 Monitor Performance This chapter explains how to enable and view performance monitoring statistics for the Cisco ONS Performance monitoring (PM) parameters are used by service providers to gather, store, and set thresholds and report performance data for early detection of problems. For more PM information, details, and definition, refer to the Cisco ONS Reference Manual. Before You Begin Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS Troubleshooting Guide as necessary. This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs). 1. NTP-A253 Change the PM Display, page 9-2 Complete as needed to change the displayed PM counts. 2. NTP-A122 Monitor Electrical Performance, page 9-3 Complete as needed to monitor electrical performance. 3. NTP-A198 Monitor Ethernet Performance, page 9-5 Complete as needed to monitor Ethernet performance. 4. NTP-A279 Create or Delete Ethernet RMON Thresholds, page 9-5 Complete as needed to create or delete Ethernet remote monitoring (RMON) thresholds. 5. NTP-A250 Monitor OC-N Performance, page 9-6 Complete as needed to monitor optical (OC-N) performance. 6. NTP-A347 Monitor Multirate Performance, page 9-7 Complete as needed to monitor multirate (MRC-N) performance. 7. NTP-A285 Monitor FC_MR-4 Performance, page 9-7 Complete as needed to monitor FC_MR-4 performance. 8. NTP-A289 Create or Delete FC_MR-4 RMON Thresholds, page 9-8 Complete as needed to create or delete FC_MR-4 RMON thresholds. 9. NTP-A357 Enable or Disable AutoPM, page 9-8 Complete as needed to enable or disable automatic autonomous performance monitoring (AutoPM) reports. 9-1
2 NTP- A253 Change the PM Display Chapter 9 Monitor Performance Note For additional information regarding PM parameters, refer to the Digital transmission surveillance section in Telcordia s GR-1230-CORE, GR-820-CORE, GR-499-CORE, and GR-253-CORE documents, and in the ANSI document entitled Digital Hierarchy - Layer 1 In-Service Digital Transmission Performance Monitoring. NTP-A253 Change the PM Display This procedure enables you to change the display of PM counts by selecting drop-down list or radio button options in the Performance window. Step 3 are already logged in, continue with. In node view, double-click the electrical, Ethernet, optical (OC-N), or multirate transport cards where you want to view PM counts. The card view appears., use the following tasks to change the display of PM counts: DLP-A124 Refresh PM Counts at 15-Minute Intervals, page DLP-A125 Refresh PM Counts at One-Day Intervals, page DLP-A347 Refresh E-Series and G-Series Ethernet PM Counts, page DLP-A126 View Near-End PM Counts, page DLP-A127 View Far-End PM Counts, page DLP-A348 Monitor PM Counts for a Selected Signal, page DLP-A129 Reset Current PM Counts, page DLP-A349 Clear Selected PM Counts, page DLP-A458 Clear All PM Thresholds, page DLP-A260 Set Auto-Refresh Interval for Displayed PM Counts, page DLP-A259 Refresh Ethernet PM Counts at a Different Time Interval, page DLP-A261 Refresh PM Counts for a Different Port, page
3 Chapter 9 Monitor Performance NTP- A122 Monitor Electrical Performance NTP-A122 Monitor Electrical Performance This procedure enables you to view node near-end or far-end performance during selected time intervals on an electrical card and port to detect possible performance problems. Step 3 are already logged in, continue with Step 3. Complete the following procedures depending on card type: For DS3XM-12 cards, complete the following procedures: DLP-A394 View DS-N/SONET PM Parameters for the DS3XM-12 Card, page DLP-A395 View BFDL PM Parameters for the DS3XM-12 Card, page For EC-1 cards, complete the DLP-A122 Enable/Disable Intermediate Path Performance Monitoring task on page 18-9 as needed to enable or disable monitoring of synchronous transport signal (STS) traffic through intermediate nodes. For all other electrical cards, continue with Step 3. In node view, double-click the electrical card where you want to view PM counts. The card view appears. Step 4 Click the Performance tab (Figure 9-1). 9-3
4 NTP- A122 Monitor Electrical Performance Chapter 9 Monitor Performance Figure 9-1 Viewing Electrical Card Performance Monitoring Information Card View Performance tab Directions radio buttons Intervals radio buttons Signal-type port drop-down list Refresh button Auto-refresh drop-down list Baseline button Clear button Help button Step 5 Step 6 Step 7 In the signal-type drop-down lists, choose the applicable port on the card you selected. Click Refresh. View the PM parameter names that appear in the Param column. The PM parameter values appear in the Curr (current) and Prev-n (previous) columns. For PM parameter definitions, refer to the Performance Monitoring chapter in the Cisco ONS Reference Manual. To refresh, reset, or clear PM counts, see the NTP-A253 Change the PM Display procedure on page
5 Chapter 9 Monitor Performance NTP- A198 Monitor Ethernet Performance NTP-A198 Monitor Ethernet Performance This procedure enables you to view node transmit and receive performance during selected time intervals on an Ethernet card and port to detect possible performance problems. Onsite are already logged in, continue with. Complete the DLP-A256 View Ethernet Statistics PM Parameters task on page Step 3 Complete the DLP-A257 View Ethernet Utilization PM Parameters task on page Step 4 Complete the DLP-A258 View Ethernet History PM Parameters task on page Step 5 Complete the DLP-A320 View ML-Series Ether Ports PM Parameters task on page Step 6 Complete the DLP-A321 View ML-Series POS Ports PM Parameters task on page Step 7 Complete the DLP-A562 View ML-Series RPR Span PM Parameters task on page Step 8 Step 9 0 Complete the DLP-A391 View CE-Series Ether Ports and POS Ports Statistics PM Parameters task on page Complete the DLP-A392 View CE-Series Ether Ports and POS Ports Utilization PM Parameters task on page Complete the DLP-A393 View CE-Series Ether Ports and POS Ports History PM Parameters task on page NTP-A279 Create or Delete Ethernet RMON Thresholds This procedure creates or deletes Ethernet RMON thresholds for the ONS Provisioning or higher 9-5
6 NTP- A250 Monitor OC-N Performance Chapter 9 Monitor Performance Complete the DLP-A60 Log into CTC task on page If you are already logged in, continue with. Perform any of the following tasks as needed: DLP-A533 Create Ethernet RMON Alarm Thresholds, page DLP-A529 Delete Ethernet RMON Alarm Thresholds, page NTP-A250 Monitor OC-N Performance This procedure enables you to view node near-end or far-end performance during selected time intervals on an OC-N card and port to detect possible performance problems. Step 3 are already logged in, continue with. Complete the DLP-A121 Enable/Disable Pointer Justification Count Performance Monitoring task on page 18-7 as needed to enable or disable clock synchronization monitoring. Complete the DLP-A122 Enable/Disable Intermediate Path Performance Monitoring task on page 18-9 as needed to enable or disable monitoring of STS traffic through intermediate nodes. Step 4 Complete the DLP-A507 View OC-N PM Parameters task on page To refresh, reset, or clear PM counts, see the NTP-A253 Change the PM Display procedure on page
7 Chapter 9 Monitor Performance NTP- A347 Monitor Multirate Performance NTP-A347 Monitor Multirate Performance This procedure enables you to view node near-end or far-end performance during selected time intervals on an MRC-N card and port to detect possible performance problems. Step 3 are already logged in, continue with. Complete the DLP-A121 Enable/Disable Pointer Justification Count Performance Monitoring task on page 18-7 as needed to enable or disable clock synchronization monitoring. Complete the DLP-A122 Enable/Disable Intermediate Path Performance Monitoring task on page 18-9 as needed to enable or disable monitoring of STS traffic through intermediate nodes. Step 4 Complete the DLP-A557 View Multirate PM Parameters task on page To refresh, reset, or clear PM counts, see the NTP-A253 Change the PM Display procedure on page 9-2. NTP-A285 Monitor FC_MR-4 Performance This procedure enables you to view node transmit and receive performance during selected time intervals on an FC_MR-4 card and port to detect possible performance problems. Onsite are already logged in, continue with. 9-7
8 NTP- A289 Create or Delete FC_MR-4 RMON Thresholds Chapter 9 Monitor Performance Complete the DLP-A350 View FC_MR-4 Statistics PM Parameters task on page Step 3 Complete the DLP-A351 View FC_MR-4 Utilization PM Parameters task on page Step 4 Complete the DLP-A352 View FC_MR-4 History PM Parameters task on page NTP-A289 Create or Delete FC_MR-4 RMON Thresholds Use this procedure to create or delete FC_MR-4 RMON thresholds for the ONS Provisioning or higher Complete the DLP-A60 Log into CTC task on page If you are already logged in, continue with. Perform any of the following tasks as needed: DLP-A357 Create FC_MR-4 RMON Alarm Thresholds, page DLP-A358 Delete FC_MR-4 RMON Alarm Thresholds, page NTP-A357 Enable or Disable AutoPM This procedure allows you to enable or disable automatic autonomous performance monitoring (AutoPM) reports. Provisioning or higher Step 3 Step 4 Complete the DLP-A60 Log into CTC task on page If you are already logged in, continue with. Click the Provisioning > Defaults tabs. In the Defaults Selector area, click NODE > General and choose NODE.general.AutoPM. In the Default Value field, select True to enable AutoPM. 9-8
9 Chapter 9 Monitor Performance NTP- A357 Enable or Disable AutoPM Step 5 Step 6 Click Apply. Follow Steps 1 through 5 to disable AutoPM. Select False in the Default Value field in Step 4 before proceeding to Step
10 NTP- A357 Enable or Disable AutoPM Chapter 9 Monitor Performance 9-10
DLPs A100 to A199. DLP-A111 Changing the Maximum Number of Session Entries for Alarm History CHAPTER
18 CHAPTER DLPs A100 to A199 DLP-A111 Changing the Maximum Number of Session Entries for Alarm History This task changes the maximum number of session entries included in the alarm history. Use this task
Configuring Performance Monitoring, RMON, OTN, and Port Provisioning
Configuring Performance Monitoring, RMON, OTN, and Port Provisioning This chapter describes performance monitoring, RMON, and OTN, port provisioning and the configuration procedures. Understanding Performance
Create Circuits and VT Tunnels
CHAPTER 6 This chapter explains how to create Cisco ONS 15310-CL and ONS 15310-MA electrical circuits, Virtual Tributary (VT) tunnels, optical circuits, and Ethernet circuits. For additional information
DLPs D400 to D499. DLP-D420 Install the Public-Key Security Certificate CHAPTER
CHAPTER 21 DLPs D400 to D499 DLP-D420 Install the Public-Key Security Certificate Tools/Equipment Prerequisite Procedures Required/As Needed Onsite/Remote This task installs the ITU Recommendation X.509
Add and Remove Nodes
14 CHAPTER The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Performance Monitoring
CHAPTER 15 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
DLPs D400 to D499. DLP-D420 Install the Public-Key Security Certificate CHAPTER
21 CHAPTER DLPs D400 to D499 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path
Change Card Settings
CHAPTER 11 This chapter explains how to change transmission settings on cards in a Cisco ONS 15600. Before You Begin As necessary, complete the NTP-E57 Document Existing Provisioning procedure on page
Add and Remove Nodes
CHAPTER 12 The terms Unidirectional Path Switched Ring and UPSR may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
This task removes a firewall tunnel. Tools/Equipment None
CHAPTER 18 DLPs D100 to D199 DLP-D100 Delete a Proxy Tunnel This task removes a proxy tunnel. Superuser only Click the Provisioning > Network > Proxy tabs. Click the proxy tunnel that you want to delete.
CTC Information and Shortcuts
APPENDIX A This appendix describes how to navigate in the Cisco Transport Controller (CTC), change CTC table data displays, and lists menu and tool options for the Cisco ONS 15454. This appendix also describes
Create Circuits and VT Tunnels
CHAPTER 8 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Performance Monitoring
CHAPTER 15 Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds, and report performance data for early detection of problems. In this chapter, PM parameters
Manage Circuits. Before You Begin CHAPTER. This chapter explains how to manage Cisco ONS SDH electrical, optical and Ethernet circuits.
CHAPTER 9 This chapter explains how to manage Cisco ONS 15454 SDH electrical, optical and Ethernet circuits. Before You Begin To create circuits, see Chapter 6, Create Circuits and Low-Order Tunnels. To
Manage Circuits. Before You Begin CHAPTER
CHAPTER 8 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Create Circuits and Low-Order Tunnels
CHAPTER 6 Create Circuits and Low-Order Tunnels The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a
General Troubleshooting
CHAPTER 1 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Add and Remove Nodes
13 CHAPTER The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Create Circuits. Before You Begin CHAPTER
CHAPTER 6 Create Circuits The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched
Convert Network Configurations
13 CHAPTER The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
CE Ethernet Operation
25 CHAPTER Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring
Provision Transponder and Muxponder Cards
CHAPTER 5 This chapter explains how to provision transponder (TXP), muxponder (MXP), Xponder (GE_XP and 10GE_XP), and ADM-10G cards. The provisioning must be performed before you provision the dense wavelength
Cisco ONS SDH Release 4.7 Network Element Defaults
Cisco ONS 15454 SDH Release 4.7 Network Element Defaults This document describes the factory-configured (default) network element (NE) settings for the Cisco ONS 15454 SDH. It includes descriptions of
CTC Information and Shortcuts
APPENDIX A Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring
General Troubleshooting
1 CHAPTER The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Turn Up a Node. Before You Begin CHAPTER
CHAPTER 4 Turn Up a Node This chapter explains how to provision a single Cisco ONS 15600 node and turn it up for service, including node name, date and time, timing references, network attributes such
CTC Information and Shortcuts
APPENDIX A This appendix describes how to navigate in the Cisco Transport Controller (CTC), change CTC table data displays, and lists menu and tool options for the Cisco ONS 15454 SDH. This appendix also
Card Protection. 4.1 Overview CHAPTER
CHAPTER 4 Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring
Create Circuits. Before You Begin CHAPTER
6 CHAPTER Create Circuits This chapter explains how to create Cisco ONS 15600 SDH circuits and tunnels. For additional information, refer to the Circuits and Tunnels chapter in the Cisco ONS 15600 SDH
Add and Remove Nodes
CHAPTER 14 Add and Remove Nodes This chapter explains how to add and remove Cisco ONS 15454 SDH nodes from multiplex section-shared protection rings (MS-SPRings), subnetwork connection protection (SNCP)
Introduction Metro Area Optical Networks Components of a MAN Metro Service POP Core MAN Services Access Services Metro Optical Services Service POP
Introduction Metro Area Optical Networks Components of a MAN Metro Service POP Core MAN Services Access Services Metro Optical Services Service POP Services Core Services MAON Physical Topologies Four
Create Circuits and Low-Order Tunnels
6 CHAPTER Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring
Card Protection. 7.1 Electrical Card Protection CHAPTER
CHAPTER 7 Card ion This chapter explains the Cisco ONS 15454 card protection configurations. To provision card protection, refer to the Cisco ONS 15454 Procedure Guide. Chapter topics include: 7.1 Electrical
Performance Monitoring
12 CHAPTER Performance Monitoring Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional
CTC Information and Shortcuts
APPENDIXA CTC Information and Shortcuts Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional
Create Circuits and Low-Order Tunnels
6 CHAPTER This chapter explains how to create Cisco ONS 15454 SDH low-order circuits and tunnels, high-order circuits, Ethernet circuits, and virtual concatenated (VCAT) circuits. For additional information
This document provides information about Cisco NCS users and node timing. The document contains the topics mentioned below.
Introduction This document provides information about Cisco NCS users and node timing. The document contains the topics mentioned below. Node Timing Parameters, page 1 Network Timing, page 2 Synchronization
Introduction. Node Timing Parameters. Revised: June 5, 2017, OL This document provides information about Cisco NCS users and node timing.
Timing Reference Revised: June 5, 2017, OL-25030-01 Introduction This document provides information about Cisco NCS users and node timing. Note With references provided to configuration guides, see: For
CTC Information and Shortcuts
APPENDIXA CTC Information and Shortcuts This appendix describes how to navigate in the Cisco Transport Controller (CTC) and change CTC table data. It also describes menu and tool options and the shelf
Administrative and Service States
APPENDIXB Administrative and Service States This appendix describes the administrative and service states for Cisco ONS 15454 SDH cards, ports, and cross-connects. For circuit state information, see Chapter
Performance Monitoring
15 CHAPTER Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds, and report performance data for early detection of problems. In this chapter, PM parameters
Upgrading the Cisco ONS CL to Release 7.0
This document explains how to upgrade Cisco ONS 15310-CL Cisco Transport Controller (CTC) software from Release 5.x or Release 6.x to Release 7.0.x, or from Release 7.0.x to a later maintenance release
9. NTP-C11 Remove and Replace an Ethernet Card, page 1-13 As needed, complete this procedure to remove and replace an ONS CL Ethernet card.
CHAPTER 1 This chapter provides procedures for installing the Cisco ONS 15310-CL shelf, cards, and fiber-optic cable. To view a summary of the tools and equipment required for installation, see the Required
Overview of the ML-Series Card
CHAPTER 1 This chapter provides an overview of the ML-100T-8 card for Cisco ONS 15310-CL and the Cisco ONS 15310-MA. It lists Ethernet and SONET capabilities and Cisco IOS and Cisco Transport Controller
CTC Information and Shortcuts
APPENDIXA Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring
Install the Cisco ONS CL
CHAPTER 1 This chapter provides procedures for installing the Cisco ONS 15310-CL shelf, cards, and fiber-optic cable. To view a summary of the tools and equipment required for installation, see the Required
SONET Topologies and Upgrades
CHAPTER 9 Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring
A.1 Cisco ONS CL Shelf Specifications. This section includes hardware and software specifications.
APPENDIX A Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring
Cisco Transport Controller Operation
CHAPTER 5 This chapter describes Cisco Transport Controller (CTC), the Cisco ONS 15310-CL and Cisco ONS 15310-MA software interface. For CTC set up and login information, refer to the Cisco ONS 15310-CL
CTC Information and Shortcuts
APPENDIXA CTC Information and Shortcuts Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional
Cisco ONS CL Shelf Assembly Hardware
CHAPTER 1 This chapter provides a description of Cisco ONS 15310-CL shelf hardware. Instructions for installing equipment are provided in the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide.
Upgrading Cisco ONS to Release 6.0
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Install the Cisco ONS CL
1 CHAPTER This chapter provides procedures for installing the Cisco ONS 15310-CL shelf, cards, and fiber-optic cable. To view a summary of the tools and equipment required for installation, see the Required
Upgrading the Cisco ONS to Release 7.2
October 2007 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Best Practices When Configuring Circuits on the ONS 15454
Best Practices When Configuring Circuits on the ONS 15454 Document ID: 13557 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Automatically Provisioned
DLPs C200 to C299. DLP-C200 Provision OSI Routing Mode CHAPTER
19 CHAPTER DLPs C200 to C299 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path
ML-Series Card Overview
CHAPTER 1 This chapter provides an overview of the ML1000-2 and ML100T-12 cards for the ONS 15454 (SONET) and ONS 15454 SDH. It lists Ethernet and SONET/SDH capabilities and Cisco IOS and Cisco Transport
Connect the PC and Log into the GUI
CHAPTER 3 Connect the PC and Log into the GUI This chapter explains how to connect PCs and workstations to the Cisco ONS 15600 SDH and how to log into Cisco Transport Controller (CTC) software, which is
Configuring POS. POS on the ML-Series Card. ML-Series SONET and SDH Circuit Sizes CHAPTER
CHAPTER 5 This chapter describes advanced packet-over-sonet/sdh (POS) interface configuration for the ML-Series card. Basic POS interface configuration is included in Chapter 4, Configuring Interfaces.
POS on ONS Ethernet Cards
20 CHAPTER This chapter describes packet-over-sonet/sdh (POS) and its implementation on ONS Ethernet cards. This chapter contains the following major sections: POS Overview, page 20-1 POS Interoperability,
Performance Monitoring
11 CHAPTER The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Cisco Transport Controller Operation
CHAPTER 8 This chapter describes Cisco Transport Controller (CTC), the software interface for the Cisco ONS 15454. For CTC set up and login information, refer to the Cisco ONS 15454 Procedure Guide. Chapter
Connect the PC and Log into the GUI
CHAPTER 3 Connect the PC and Log into the GUI This chapter explains how to connect PCs and workstations to the Cisco ONS 15454 and how to log into Cisco Transport Controller (CTC) software, which is the
Connect the PC and Log into the GUI
CHAPTER 3 This chapter explains how to connect Windows PCs and Solaris workstations to the Cisco ONS 15310-CL and Cisco ONS 15310-MA, and how to log into Cisco Transport Controller (CTC) software. CTC
Configure Controller and AP Settings
Configure SNMP Credentials for Rogue AP Tracing, on page 1 Configure Protocols for CLI Sessions, on page 2 Enable Unified AP Ping Reachability Settings on the Prime Infrastructure, on page 2 Refresh Controllers
Performance Monitoring
15 CHAPTER Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for, and report performance data for early detection of problems. In this chapter, PM parameters
POS on ONS Ethernet Cards
CHAPTER 23 This chapter describes packet-over-sonet/sdh (POS) and its implementation on ONS Ethernet cards. This chapter contains the following major sections: POS Overview, page 23-1 POS Interoperability,
Configuring POS interfaces
Contents Configuring POS interfaces 1 Overview 1 SONET 1 SDH 1 POS 1 Configuration procedure 1 Displaying and maintaining POS interfaces 3 POS interface configuration examples 4 Directly connecting switches
Command Reference APPENDIX
APPENDIX A Note The terms Unidirectional Path Switched Ring and UPSR may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Configuring Ethernet OAM and Connectivity Fault Management
Configuring Ethernet OAM and Connectivity Fault Management This chapter describes Ethernet OAM, Connectivity Fault Management (CFM), and Y.1731 features. This chapter also describes procedures to configure
Install Cards and Fiber-Optic Cable
CHAPTER 2 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Configuring Dense Wavelength Division Multiplexing Controllers
Configuring Dense Wavelength Division Multiplexing Controllers This module describes the configuration of dense wavelength division multiplexing (DWDM) controllers. DWDM is an optical technology that is
Media Path Analysis. Analyzing Media Paths Using IP SLA. Before You Begin. This section contains the following:
This section contains the following: Analyzing Media Paths Using IP SLA, page 1 Analyzing Media Paths Using VSAA, page 3 Managing a Video Test Call, page 6 Analyzing Media Paths Using IP SLA To start a
Circuits and Tunnels Overview CHAPTER
CHAPTER 11 Circuits and Tunnels This chapter explains Cisco ONS 15454 synchronous transport signal (STS), virtual tributary (VT), and virtual concatenated (VCAT) circuits and VT, data communications channel
Release Notes for Cisco ONS Release 3.0.3
Release Notes for Cisco ONS 15454 Release 3.0.3 Release Notes address closed (maintenance) issues, caveats, and new features for the Cisco ONS 15454 SONET multiplexer. For detailed information regarding
Cisco 2-Port, 4-Port, and 8-Port OC-12c/STM-4 Packet over SONET Shared Port Adapters
Cisco 2-Port, 4-Port, and 8-Port OC-12c/STM-4 Packet over SONET Shared Port Adapters The Cisco I-Flex design combines shared port adapters (SPAs) and SPA interface processors (SIPs), using an extensible
Upgrading the Cisco ONS CL to Release
Upgrading the Cisco ONS 15310-CL to Release 9.2.1.3 This document explains how to upgrade Cisco ONS 15310-CL Cisco Transport Controller (CTC) software from Releases 7.2.2, 7.2.3, 8.5.1, 8.6.1, 9.0.3, 9.1.0
Upgrade, Add, and Remove Cards and Nodes
12 CHAPTER Upgrade, Add, and Remove Cards and Nodes The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in
Configuring Ethernet CFM
CHAPTER 46 The Catalyst 4500 series switch supports Standardized (Draft 8.1) IEEE 802.1ag Connectivity Fault Management (CFM) and IEEE 802.3ah Ethernet OAM discovery, link monitoring, remote fault detection,
Error Messages CHAPTER
4 CHAPTER Error Messages Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path
Connecting and Routing the Cables
This chapter describes how to connect and route the cables for NCS 2015. The sections are: Cable Routing and Management, on page 1 NTP-L55 Routing and Locking Cable and Fiber Modules, on page 2 NTP-L56
SONET Bidirectional Line-Switched Ring Equipment Generic Criteria
Contents SONET Bidirectional Line-Switched Ring Equipment Generic Criteria Contents Contents 1. Introduction... 1 1 1.1 Update History...1 2 1.2 Scope...1 4 1.3 Criteria...1 5 1.4 Requirement Labeling
Troubleshooting the Network Analysis Module. Netflow Data Export. Web Application CHAPTER
CHAPTER 5 This chapter describes how to troubleshoot the NAM and includes these sections: Netflow Data Export, page 5-1 Error Messages, page 5-9 Web Username and Password Guidelines, page 5-15 Supported
Common Issues With Two Fiber Bidirectional Line Switched Rings
Common Issues With Two Fiber Bidirectional Line Switched Rings Document ID: 13556 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Working and Protect
Install Cards and Fiber-Optic Cable
CHAPTER 2 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
SNMP SNMP Overview CHAPTER
CHAPTER 18 This chapter explains Simple Network Management Protocol () as implemented by the Cisco ONS 15454. For setup information, refer to the Cisco ONS 15454 Procedure Guide. Chapter topics include:
Optical Channel Circuits and Virtual Patchcords Reference
CHAPTER 11 Optical Channel Circuits and Virtual Patchcords Reference This chapter explains the Cisco ONS 15454 dense wavelength division multiplexing (DWDM) optical channel (OCH) circuit types and virtual
Storage Access Networking Cards
CHAPTER 6 The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Archiving and Purging Data from the Database
CHAPTER 10 These topics provide basic information about data purging and archiving and system stability: Prime Network Database Schemas, page 10-1, describes the schemas supported by the Prime Network
Auto In-Service State for Ports
This document describes the Auto In-Service State (AINS) feature on the port. Effective Cisco IOS XE Everest 16.6.1, the Cisco NCS 4200 Series support management of equipment and port state model in two
Error Messages. Error Messages Reference
Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Installing Cisco ONS SONET/SDH MRC-12 Cards
Installing Cisco ONS 15454 SONET/SDH 15454 MRC-12 Cards Product Name: 15454-MRC-I-12 (SONET); 15454E-MRC-I-12 (SDH) This document provides card specifications and describes installation and removal procedures
Archiving and Purging Data
CHAPTER 10 These topics provide basic information about data purging and archiving and system stability: Prime Network Database Schemas, page 10-1, describes the schemas supported by the Prime Network
Manage the Node. Before You Begin CHAPTER
CHAPTER 10 This chapter explains how to modify node provisioning for the Cisco ONS 15454 and perform common management tasks such as monitoring the dense wavelength division multiplexing (DWDM) automatic
Cisco Transport Manager Release 9.0 ML Provisioning Methodology
Cisco Transport Manager Release 9.0 ML Provisioning Methodology May 26, 2010 This document describes the methodology that Cisco Transport Manager (CTM) Release 9.0 uses to provision ML-series cards. This
Installing Cisco ONS XC10G Cards
Product Name: 15454-XC-10G This document contains a description of XC10G card features, installation procedures, removal instructions, and technical specifications Use this document in conjunction with
Differences Between SONET and SDH Framing in Optical Networks
Differences Between SONET and SDH Framing in Optical Networks Document ID: 16180 Contents Introduction Prerequisites Requirements Components Used Conventions SONET and SDH Framing ATM Over SONET Packet
Cisco Transport Controller Operation
CHAPTER 8 Cisco Transport Controller Operation This chapter describes Cisco Transport Controller (CTC), the Cisco software interface for the Cisco ONS 15454 SDH. For CTC set up and login information, refer
Table of Contents 1 E-CPOS Interface Configuration 1-1
Table of Contents 1 E-CPOS Interface Configuration 1-1 Overview 1-1 SONET 1-1 SDH 1-1 E-CPOS 1-5 Configuring an E-CPOS Interface 1-6 Configuring an E-CPOS Interface 1-6 Configuring the Operating Mode of
Cisco Prime Optical ML Provisioning Methodology
Cisco Prime Optical 9.6.3 ML Provisioning Methodology March 8, 2013 This document describes the methodology that Cisco Prime Optical 9.6.3 uses to provision ML-series cards. This document contains the