STEVAL-IDW001V1. Wi-Fi daughterboard for STM32F0DISCOVERY. Description. Features
|
|
- Tamsyn Palmer
- 5 years ago
- Views:
Transcription
1 STEVAL-IDW00V Wi-Fi daughterboard for STMF0DISCOVERY Description Data brief Features Integrated SPWF0SA. Wi-Fi module Used as daughterboard for the STMF0DISCOVERY Can be used with the STEVAL-PCC0V UART to USB bridge board Integrated reset button Integrated power LED Dimensions: mm x mm RoHS compliant The STEVAL-IDW00V provides a platform for evaluation of ST s SPWF0SA. Wi-Fi module. This product evaluation board integrates connectors for use in conjunction with the STMF0DISCOVERY or with the STEVAL- PCC0V. With the STMF0DISCOVERY, it can be used as a USB dongle on a PC to evaluate the AT commands that are available in the Wi-Fi module firmware. This can be done using a PC utility such as HyperTerminal or similar. When integrated with the STMF0DISCOVERY, the STEVAL-IDW00V allows the use of the Wi- Fi module as a network co-processor for the STMF0 microcontroller. In this case it is necessary to write an application for the microcontroller to pilot the Wi-Fi module capabilities. February 0 DocID0 Rev / For further information contact your local STMicroelectronics sales office.
2 Schematic diagram STEVAL-IDW00V Schematic diagram Figure. STEVAL-IDW00V circuit schematic +V_Vin GND_0V (on Ext. board) +.V PC0 (on Ext. board) PC (on Ext. board) PC (on Ext. board) PC (on Ext. board) PC_MHz_EN (on Ext. board) LP_CLK (on Ext. board) PB (on Ext. board) PB (on Ext. board) PB (on Ext. board) JTMS (on Ext. board) JTCK (on Ext. board) JTDI (on Ext. board) JTDO (on Ext. board) JTRST (on Ext. board) TAMPER (on Ext. board) PC PC PC PC NRST JTDI JTMS JTCK JTDO JNTRST PC.V +.V_CP0 PC GPIO0 PB (on Ext. board) PB (on Ext. board) PB (on Ext. board) PB (on Ext. board) PB (on Ext. board) PB0 (on Ext. board) PB (on Ext. board) PB (on Ext. board) PB (on Ext. board) PB0 (on Ext. board) PA/MCO (on Ext. board) PA (on Ext. board) PA (on Ext. board) PA (on Ext. board) PA (on Ext. board) GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO0 +.V_CP0 +.V +.V_mod R 0 Ohm LED ED GREE REEN PB_F0 (on Ext. board) PB_F0 (on Ext. board) VDD_F0 (on Ext. board) BOOT0_F0 (on Ext. board) PB_F0 (on Ext. board) PB_F0 (on Ext. board) PB_F0 (on Ext. board) PB_F0 (on Ext. board) PB_F0 (on Ext. board) PD_F0 (on Ext. board) PC_F0 (on Ext. board) PC_F0 (on Ext. board) PC0_F0 (on Ext. board) PA_F0 (on Ext. board) PA_F0 (on Ext. board) PF_F0 (on Ext. board) PF_F0 (on Ext. board) PA_F0 (on Ext. board) (PA_F0) (PA_F0) (PA0_F0) (PA_F0) PA_F0 (on Ext. board) PA PA0 PA PA PC PC R..K J B V_mod +.V_mod CON ON FEMALE Conn..V +.V +.V_mod STLQ0CR U.V Connettore sul bordo per mini dongle PA PA +.V_mod PA0.V.V PA PC PC PC PC PC +.V VBAT_F0 (on Ext. board) PC_F0 (on Ext. board) PC_F0 (on Ext. board) PC_F0 (on Ext. board) PF0_F0 (on Ext. board) PF_F0 (on Ext. board) PC0_F0 (on Ext. board) (PC_F0) (PC_F0) (PC_F0) PA0_F0 (on Ext. board) PA_F0 (on Ext. board) PA_F0 (on Ext. board) PA_F0 (on Ext. board) (PF_F0) (PF_F0) PA_F0 (on Ext. board) PA_F0 (on Ext. board) PA_F0 (on Ext. board) PA_F0 (on Ext. board) PC_F0 (on Ext. board) FEMALE Conn. N/C IN GND N/C OUT WF F GPIO_TXD 0 GPIO_SPICS GPIO_ADC GPIO_RXD GPIO_MOSI ANTENN NTENNA LED ED R 0 0K J A 0 0 TDO_SCK TRST_MISO 0 TCK TDI VIN/.V TMS C 00 00n J A NM N..M 0 0 R C 00 00n C 00 00n LED ED 0 C u uf GPIO_SCLK BOOT0 GPIO_ADC0 GND GPIO_ADC GPIO_DAC GPIO0 TXD RXD CTS_DN GPIO0_MISO RTS_DP GPIO GPIO_SCL GPIO GPIO_SDA GPIO_ADC GND J CON ON R..K R STG TG B B U J B 0 0 CON ON R..K DIR VCCB DIR VCCA GND OE J C 00 00n SW W SW PUSHBUTTON C 00 00n 0 A A 0 JP P R 0 Ohm R..K SW W SW PUSHBUTTON C 00 00n J R..K C 00 00n TP P C 0 0u..V C 00 00n C n R 0 0 Ohm R..K LED ED YELLO ELLOW JP P JP P R JP P R..K GSPG0DI0 / DocID0 Rev
3 STEVAL-IDW00V Revision history Revision history Table. Document revision history Date Revision Changes -Feb-0 Initial release. DocID0 Rev /
4 STEVAL-IDW00V Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 0 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America / DocID0 Rev
5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: STMicroelectronics: STEVAL-IDW00V
STEVAL-SPBT4ATV3. USB dongle for the Bluetooth class 1 SPBT2632C1A.AT2 module. Features. Description
USB dongle for the Bluetooth class 1 SPBT2632C1A.AT2 module Features Based on V3.0 Bluetooth class 1 module, SPBT2632C1A.AT2 USB interface and power supply Supported reprogrammability via USB interface
More informationAN2261 APPLICATION NOTE
APPLICATION NOTE GPIO ports configuration in ST30 devices INTRODUCTION The General Purpose IO (GPIO) Ports of ST30 devices are programmable by software in several modes:, Output, Alternate Function,, Output
More informationSTEVAL-CCM002V1. TFT-LCD panel demonstration board based on the STM32 as LCD controller. Features. Description
TFT-LCD panel demonstration board based on the STM32 as LCD controller Data brief Features Displays images on a TFT-LCD using the STM32 as LCD controller Includes a slideshow of images to demonstrate static
More informationDescription SPC564A-DISP. March 2014 DocID Rev 3 1/5
SPC564A-DISP: Discovery+ evaluation board Description Data brief - production data Features SPC564A70L7 32-bit 150 MHz e200z4 Power Architecture core, 2Mbyte on-chip in an LQFP176 package. Board Supply:
More informationSTEVAL-PCC010V1. ST802RT1A Ethernet PHY demonstration board with STM32F107 controller add-on board. Features. Description
ST802RT1A Ethernet PHY demonstration board with STM32F107 controller add-on board Data brief Features ST802RT1A Ethernet PHY demonstration board: ST802RT1A fast Ethernet physical layer transceiver On-board
More informationST21NFCB. Near field communication controller. Features. RF communications. Hardware features. Communication interfaces. Electrical characteristics
Near field communication controller Data brief Features NFC operating modes supported: Card emulation Reader / Writer Peer-to-peer communication Hardware features FBGA WFBGA 64-pin 36 Kbytes of EEPROM
More informationSTM32 embedded target for MATLAB and Simulink release 3.1. Summary for STM32 embedded target for MATLAB and Simulink release 3.1:
Release note STM32 embedded target for MATLAB and Simulink release 3.1 Introduction This release note is related to STM32 embedded target for MATLAB and Simulink (STM32- MAT/TARGET). It is updated periodically
More informationAN4321 Application note
Application note Getting started with the SPC56L-Discovery Introduction SPC56L-Discovery evaluation kit is based on the 32-bit microcontrollers SPC56EL70L5. The SPC56L-Discovery is an evaluation board
More informationMain components USB charging controller with integrated power switch
DN0019 Design note Smart dual-port USB charger with STCC2540 Designs from our labs describe tested circuit designs from ST labs which provide optimized solutions for specific applications. For more information
More informationLD A very low drop adjustable positive voltage regulator. Description. Features
7 A very low drop adjustable positive voltage regulator Description Datasheet - production data Features P ² PAK Output current limit Low-dropout voltage: typically 400 mv at 7 A output current Output
More informationAN2667 Application note
Application note STM8A GPIO application examples Introduction This document is intended to provide two practical application examples of the GPIO peripheral use in the STM8A device. The examples are: Toggling
More informationAN4274 Application note
Application note The serial communication driver between the ST7580 and the STM32Fx By Vincenzo Mormina Introduction This document describes the serial communication driver between the ST7580 and the STM32Fx.
More informationAN4440 Application note
Application note RFFE HVDAC control Pascal Paillet Introduction The purpose of this application note is to familiarize mobile phone designers with RFFE HVDAC control. Common tasks are explained and more
More informationAN4113 Application note
Application note Managing the Driver Enable signal for RS-485 and IO-Link communications with the STM32F05x USART Introduction RS-485 and IO-Link are half-duplex communication protocols that offer easy
More informationUM1719 User manual. The STPM3x evaluation software. Introduction
User manual The STPM3x evaluation software Introduction The STPM3x evaluation software is a graphical user interface to read, configure and calibrate the STPM3x energy metering ICs, suitable for parallel
More informationECMF02-3F3. Common mode filter with ESD protection. Features. Description. Applications. Complies with the following standard:
Common mode filter with ESD protection Datasheet production data Figure 1. Pin configuration (bump side) 1 2 A B Flip Chip 6 bumps C Features Figure 2. Schematic (bump side) Very large differential bandwidth
More informationAN2676 Application note
Application note STM8A reset application examples Introduction This document is one of a set of application notes giving examples of how to use the various blocks of the STM8A microcontroller family and
More informationEMIF03-SIM06F3. 3-line IPAD, EMI filter including ESD protection. Description. Features. Application. Complies with the following standards:
3-line IPAD, EMI filter including ESD protection Description Datasheet production data The EMIF03-SIM06F3 chip is a highly integrated audio filter device designed to suppress EMI/RFI noise in all systems
More informationAN3996 Application Note
Application Note Adjustable LED blinking speed using STM8SVLDISCOVERY Application overview This application note provides a short description of the demonstration firmware Discover which is preprogrammed
More informationAN626 Application note
Application note Serial EEPROM product numbering This application note provides a detailed description of the part numbering scheme of Serial EEPROM products. The part numbering scheme consists of a maximum
More informationST33F1M, ST33F1M0, ST33F896, ST33F768, ST33F640, ST33F512
ST33F1M, ST33F1M0, ST33F896, ST33F768, ST33F640, ST33F512 Secure MCU with 32-bit ARM SC300 CPU, SWP interface, NESCRYPT cryptoprocessor and high-density Flash memory Data brief Micromodule DFN8 package
More informationSTM3220G-SK/KEI. Keil starter kit for STM32F2 series microcontrollers (STM32F207IG MCU) Features. Description
Keil starter kit for STM32F2 series microcontrollers (STM32F207IG MCU) Data brief Features The Keil MDK-Lite development tools: µvision 4 IDE/Debugger for application programming and debugging ARM C/C++
More informationAN4464 Application note
Application note Porting a Green Hills SW to SPC5Studio Introduction SPC5Studio provides a comprehensive framework to design, build and deploy embedded applications for SPC56 Power Architecture 32-bit
More informationST10F271B/E, ST10F272B/E Errata sheet
Errata sheet BAG silicon version Introduction Note: This errata sheet describes all the functional and electrical problems known in the BAG silicon version of ST10F271B, ST10F271E, ST10F272B and ST10F272E
More informationAN4308 Application note
Application note Methods of STCC2540, STCC5011, STCC5021 control Introduction By Ondrej Plachy The STCC2540 and STCC5011/STCC5021 (STCCxxxx in text below) devices are combinations of a current limited
More informationAN2143 Application note
AN2143 Application note Programming the ST10F27X embedded Flash using the ST10FLASHER tool Introduction This document summarizes the different steps needed to program the internal Flash memory of the ST10F27x
More informationThis document describes the hardware architecture of the board, how to configure the jumpers and to enable specific functions.
User manual SPC560B-DIS discovery board Introduction This document describes the hardware architecture of the board, how to configure the jumpers and to enable specific functions. November 2013 DocID025237
More informationSTEVAL-VNH5019A. Motor driver evaluation board based on VNH5019A. Description. Features
STEVAL-VNH5019A Motor driver evaluation board based on VNH5019A Description Data brief Features Type R DS(on) I out V CC(max) VNH5019A-E 18 mω typ (per leg) 30 A 41 V Handling up to 30 A of maximum motor
More informationAN2672 Application note
Application note I²C application examples Introduction The I 2 C peripheral is very flexible, supporting standard interrupts in both 10-bit and 7-bit addressing modes. As a result, generated events are
More informationSTM3210B-SK/KEIL STR91X-SK/KEI, STR7-SK/KEIL
STM3210B STR91X-SK/KEI, STR7 Keil starter kits for ST ARM core-based microcontrollers Data brief Features The ARM RealView Microcontroller Development Kit complete development software package with: µvision3
More informationUM1572 User manual. STEVAL-IPE020V1: ST energy meter application based on the Android platform. Introduction
User manual STEVAL-IPE020V1: ST energy meter application based on the Android platform Introduction The ST energy meter application is a user friendly Android based solution based on NFC technology that
More informationDescription of STM8 LIN software package (STSW-STM8A-LIN) release 4.1. Table 1. Release information. STM8 LIN package
Release note Description of STM8 LIN software package (STSW-STM8A-LIN) release 4.1 Introduction The STM8 LIN package implements the LIN 2.x (2.1 and 2.0) and LIN 1.3 protocols to drive USART/UART1 (named
More informationSTEVAL-IHM028V1. 2 kw 3-phase motor control demonstration board featuring the IGBT intelligent power module STGIPS20K60. Features.
Features 2 kw 3-phase motor control demonstration board featuring the IGBT intelligent power module STGIPS20K60 Data brief Complete solution for a 2 kw power inverter HV supply mode: voltage 90 VAC to
More informationEV-VNQ5E050AK VNQ5E050AK evaluation board
VNQ5E050AK evaluation board Data brief production data Features Parameter Symbol Value Unit Max supply voltage V CC 41 V Operating voltage range V CC 4.5 to 28 V Max On-State resistance R ON 50 mω Current
More informationAN2470 Application note TS4871 low voltage audio power amplifier Evaluation board user guidelines Features Description
Application note TS4871 low voltage audio power amplifier Evaluation board user guidelines Features TS4871 low voltage audio power amplifier with active low standby mode Operating range from V CC =2.2V
More informationAN2061 APPLICATION NOTE
APPLICATION NOTE EEPROM Emulation with ST10F2xx Description External EEPROMs are often used in automotive applications to store adaptative/evolutive data. On the other hand, the Microcontroller used in
More informationAN3980 Application note
Application note STM32 firmware library for dspin L6470 1 Introduction This application note describes the implementation of the STM32 firmware library for the dspin stepper motor control product (L6470).
More informationUM1750 User manual. STEVAL-IPE023V1: STPMxx programmer. Introduction
User manual STEVAL-IPE023V1: STPMxx programmer Introduction This evaluation board is a tool for programming the STPMxxx energy meter ICs family. The board has been developed to provide an insulated USB
More informationSTM32-MP3NL/DEC. STM32 audio engine MP3 decoder library. Description. Features
STM32 audio engine MP3 decoder library Data brief Features MPEG-1, 2 or 2.5 formats Layers 1, 2 and 3 Constant bit rate and variable bit rate Mono or stereo input streams PCM (Pulse Code Modulation) output
More informationOSPlus USB Extension. OSPlus USB 2.0 extension. Description. Features. Application. TCP/IP stack NexGenOS NexGenIP VFS. FAT Ext2 LVM Device layer
OSPlus USB 2.0 extension Data brief Application VFS FAT Ext2 LVM Device layer Device drivers TCP/IP stack NexGenOS NexGenIP NexGenRemote NexGenResolve NexGenBoot NexGenPPP USB stack OSPlus interface Class
More informationAN2855 Application note
Application note Configuration for single-click and double-click detection using the FC30 Introduction This document is intended to provide application information for the click and double-click detection
More informationAN3354 Application note
Application note STM32F105/107 in-application programming using a USB host 1 Introduction An important requirement for most Flash-memory-based systems is the ability to update firmware installed in the
More informationEVAL6235PD. L6235 three-phase brushless DC motor driver demonstration board. Features. Description
L6235 three-phase brushless DC motor driver demonstration board Features Operating supply voltage from 8 V to 52 V 5.6 A output peak current (2.8 A RMS ) Operating frequency up to 100 khz Non-dissipative
More informationUM0401 User manual. User manual for eight bit port expander STMPE801 demonstration board. Introduction
User manual User manual for eight bit port expander STMPE801 demonstration board Introduction This document explains the functioning of the demo board for the port expander Chip STMPE801 with a PC GUI
More informationAN2474 Application note
AN474 Application note TS4995.W fully differential audio power amplifier with selectable standby and 6db fixed gain - Evaluation board user guidelines Introduction This application note describes the DEMO
More informationUSB dongle for the Bluetooth class 2 SPBT3.0DP2 module
STEVAL-BTDP USB dongle for the Bluetooth class SPBT.0DP module Data brief Features Based on the V.0 Bluetooth class module SPBT.0DP USB interface and power supply Reprogramming support via USB interface
More informationAN3279 Application Note
Application Note Adjustable LED blinking speed using STM8S-DISCOVERY touch sensing key Application overview This application note provides a short description of how to use the touch sensing key to change
More informationSTM8-SK/RAIS STM8-D/RAIS ST7-SK/RAIS ST7-D/RAIS
STM8-SK/RAIS STM8-D/RAIS ST7-SK/RAIS ST7-D/RAIS Raisonance s complete, low-cost starter kits for STM8 and ST7 Features Embedded RLink USB interface to host PC In-circuit debugging and programming Application
More informationSTEVAL-ILL055V1: 11 W offline LED drive with high power factor based on HVLED815PF (EU input range) Figure 1. STEVAL-ILL055V1
User manual STEVAL-ILL055V1: 11 W offline LED drive with high power factor based on HVLED815PF (EU input range) Introduction The purpose of this document is to provide detailed information for the STEVAL-ILL055V1
More informationSTM32-SK/KEIL STR91X-SK/KEI, STR7-SK/KEIL
STM32 STR91X-SK/KEI, STR7 Keil starter kits for ST ARM core-based microcontrollers Data brief Features The ARM RealView Microcontroller Development Kit complete development software package with: µvision3
More informationSOT23-6L ESDALCL6-2SC6
Very low capacitance and low leakage current ESD protection Features 2 data-line protection Datasheet production data Protects V BUS Very low capacitance: 2.5 pf typ. Very low leakage current: 10 na at
More informationSTICE CF/Stice_Connect AD/Stice_Connect AS/Stice_Connect
STICE CF/Stice_Connect AD/Stice_Connect AS/Stice_Connect Full-featured cost-effective emulation system for ST microcontrollers Data brief Features Emulation system Real-time emulation of STM8 MCUs (CPU
More informationSTM32-SK/RAIS,STR91X-SK/RAI,STR7-SK/RAIS STM32-D/RAIS,STR9-D/RAIS,STR7-D/RAIS
STM32-SK/RAIS,,STR7-SK/RAIS STM32-D/RAIS,STR9-D/RAIS,STR7-D/RAIS Raisonance REva starter kits for ST ARM core-based microcontrollers Data brief Features Raisonance software toolset with: GNU C compiler
More informationAN2240 Application note
AN0 Application note Using the evaluation board for the TS7 low noise microphone preamplifier with V bias Introduction This application note describes the DEMO TS7 evaluation board, specifically designed
More informationST19WR08 Dual Contactless Smartcard MCU With RF UART, IART & 8 Kbytes EEPROM Features Contactless specific features
Dual Contactless Smartcard MCU With RF UART, IART & 8 Kbytes EEPROM Data Brief Features Enhanced 8-bit CPU with extended addressing modes 112 KBytes user ROM with partitioning 2 KBytes user RAM with partitioning
More informationObsolete Product(s) - Obsolete Product(s)
8 line low capacitance EMI filter and ESD protection Main product characteristics Where EMI filtering in ESD sensitive equipment is required: LCD and camera for mobile phones Computers and printers Communication
More informationAN3965 Application note
Application note STM32F40x/STM32F41x in-application programming using the USART 1 Introduction An important requirement for most Flash-memory-based systems is the ability to update firmware when installed
More informationAN3348 Application note
Application note Porting etpu code to etpu compiler build tools guides Introduction This guide would take you through the process of porting your application to the new etpu Compiler (EC). EC was designed
More informationUM0792 User manual. Demonstration firmware for the DMX-512 communication protocol transmitter based on the STM32F103Zx.
User manual Demonstration firmware for the DMX-512 communication protocol transmitter based on the STM32F103Zx Introduction This document describes how to use the demonstration firmware for the DMX-512
More informationSTTS V memory module temperature sensor. Features
2.3 V memory module temperature sensor Data brief Features is a 2.3 V memory module temperature sensor forward compatible with JEDEC standard TS3000 and backward compatible with STTS424 Operating temperature
More informationUM0693 User manual. 1 Introduction. STM8L101-EVAL demonstration firmware
User manual STM8L101-EVAL demonstration firmware 1 Introduction Note: This document describes the demonstration firmware running on the STM8L101-EVAL evaluation board. You can use it to evaluate the capabilities
More informationAN3001 Application note
Application note Demonstration board user guidelines for the TS4657 single supply stereo digital audio line driver Introduction This application note focuses on the TS4657 demonstration board, designed
More informationSTLC2500D. Bluetooth V2.1 "Lisbon" + EDR. Features. Description
Bluetooth V2.1 "Lisbon" + EDR Data Brief Features Based on Ericsson Technology Licensing Baseband Core (EBC) Bluetooth specification compliance: V2.1 ( Lisbon ) + EDR HW support for packet types ACL, SCO,
More informationAN3975 Application note
Application note Transparent serial link over ST7590 OFDM PRIME modem 1 Introduction Nowadays, a lot of power meter manufacturers or smart grid providers are switching from simple networks like RS845 to
More informationAN2734 Application note S-Touch design procedure Introduction
Application note S-Touch design procedure Introduction The purpose of this application note is to provide the system/hardware engineers enough ground knowledge to start the design of capacitive touch inferface
More informationST19NP18-TPM-I2C Trusted Platform Module (TPM) with I²C Interface Features
Trusted Platform Module (TPM) with I²C Interface Data brief Features Single-chip Trusted Platform Module (TPM) Embedded TPM 1.2 firmware I²C communication interface (Slave mode) Architecture based on ST19N
More informationAN2557 Application note
Application note STM32F10x in-application programming using the USART Introduction An important requirement for most Flash-memory-based systems is the ability to update firmware when installed in the end
More informationUM1677 User manual. Getting started with STM32F030 Value Line Discovery development tools. Introduction
User manual Getting started with STM32F030 Value Line Discovery development tools Introduction This document describes the software, firmware environment and development recommendations required to build
More informationUM1488 User manual. STPMC1 evaluation software. Introduction
User manual STPMC1 evaluation software Introduction STPMC1 evaluation software is a graphical user interface to read, configure and calibrate an STPMC1 energy metering device, suitable for parallel and
More informationSTA bit single chip baseband controller for GPS and telematic applications. Features
32-bit single chip baseband controller for GPS and telematic applications Data Brief Features Suitable for automotive applications ARM7TDMI 16/32 bit RISC CPU based host microcontroller. Complete embedded
More informationAN2825 Application Note
Application Note S-Touch STMPE811 resistive touchscreen controller advanced features Introduction This application note provides details on the advanced features of the S-Touch STMPE811 touchscreen controllers.
More informationEMIF01-SMIC01F2 IPAD. Single line EMI filter including ESD protection. Main application. Description. Benefits. Pin configuration (Bump side view)
IPAD Single line EMI filter including ESD protection Main application Single ended microphone in mobile phones and portable devices Description The is a highly integrated device designed to suppress EMI/RFI
More informationAN3154 Application note
Application note CAN protocol used in the STM32 bootloader Introduction This application note describes the CAN protocol used in the STM32 microcontroller bootloader. It details each supported command.
More informationUM0592 User manual. STEVAL-PCC006V1, HDD bridge extension board. board for mass storage applications. Introduction
User manual STEVAL-PCC006V1, HDD bridge extension board for mass storage applications Introduction This document explains the use of the HDD extension demonstration board (STEVAL- PCC006V1) which can be
More informationAN2673 Application note
Application note STM8A SPI application examples Introduction This application note is one of a set of application notes giving examples of how to use the various blocks of the STM8A microcontroller family
More informationUM1650 User manual. SPC56L-Discovery. Introduction. This document describes how to configure the board and how to setup the I/O communication.
User manual SPC56L-Discovery Introduction This document describes how to configure the board and how to setup the I/O communication. September 2013 DocID024947 Rev 3 1/23 www.st.com Contents UM1650 Contents
More informationEMIF02-SPK02F2. 2-line IPAD, EMI filter and ESD protection. Features. Application. Description. Complies with the following standards
2-line IPAD, EMI filter and ESD protection Datasheet production data Features Packaged in lead-free Flip Chip Very low resistance: 0.35 Ω High attenuation: -45 db at 900 MHz Very low PCB space consumption:
More informationUM1084 User manual. CR95HF development software user guide. Introduction. Reference documents
User manual CR95HF development software user guide Introduction The CR95HF development software is a PC software which allows to configure, evaluate, and communicate with ST CR95HF 13.56 MHz multiprotocol
More informationEMIF02-MIC01F2 2-line IPAD, EMI filter including ESD protection Features Application Description Complies with the standards:
2-line IPAD, EMI filter including ESD protection Features 2-line symetrical low-pass filter Lead-free package High-density capacitor High-efficiency EMI filtering Very small PCB footprint: 1.42 mm x 1.92
More informationAN1335 APPLICATION NOTE
AN1335 APPLICATION NOTE Using the ST10F280 By André ROGER 1 - INTRODUCTION ST10F280 is a new member of ST10 family. This device has been specifically designed for application based on C167 and that now
More informationMain components 1 A, high efficiency adjustable single inductor dual mode buckboost DC-DC converter
DN0007 Design note STBB1 buck-boost converter used as a 500mA LED driver with 1.8VDC-5.5VDC Vin Designs from our labs describe tested circuit designs from ST labs which provide optimized solutions for
More informationST33F1M. Smartcard MCU with 32-bit ARM SecurCore SC300 CPU and 1.25 Mbytes high-density Flash memory. Features. Hardware features.
Smartcard MCU with 32-bit ARM SecurCore SC300 CPU and 1.25 Mbytes high-density Flash memory Data brief Features ST33F1M major applications include: Mobile communications (GSM, 3G and CDMA) Java Card applications
More informationObsolete Product(s) - Obsolete Product(s)
2-line IPAD, EMI filter and ESD protection for speaker Figure 1. Pin configuration (top view) and basic cell configuration Input SPK R in GND SPK L in 1 Pin 1 Micro QFN 6 leads 1.45 mm x 1.00 mm (bottom
More informationSTM8 I 2 C optimized examples
Application note STM8 I 2 C optimized examples Introduction This document describes how to use the following I 2 C optimized examples Hardware configuration example of a common I 2 C bus Master firmware
More informationUM1792 User manual. STLUX385A development environment. Introduction. Reference documents
User manual STLUX385A development environment Introduction This user manual provides complete information for SW developers about the complete STLUX385A development environment flow. The STLUX385A development
More informationSMP75. Trisil for telecom equipment protection. Features. Description. Applications. Benefits
Trisil for telecom equipment protection Features bidirectional crowbar protection voltage: 8 V low leakage current: I R = 2 µa max holding current: I H = 15 ma min repetitive peak pulse current: I PP =
More informationAN3250 Application note
Application note M24LR64-R Multi-bank reference design description and settings 1 Introduction The M24LR64-R multi-bank reference design has been created to help users increase the memory density of their
More informationAN2430 Application note
Application note STR75x SystemMemory boot mode Introduction te: This application note describes the features of the SystemMemory boot mode developed for STR75x Flash microcontrollers providing all the
More informationAN2737 Application note Basic in-application programming example using the STM8 I 2 C and SPI peripherals Introduction
Application note Basic in-application programming example using the STM8 I 2 C and SPI peripherals Introduction This application note is one of a set of application notes giving examples of how to use
More informationRN0046 Release note. 1 Introduction. SimpleMAC library for STM32W108xx kits. About this release note
Release note SimpleMAC library for STM32W108xx kits 1 Introduction About this release note This release note is related to the SimpleMAC library which supports all the available STM32W108xx kits. This
More informationAN3991 Application note
Application note How to drive multiple stepper motors with the L6470 motor driver Introduction The L6470 is a flexible device for the driving of bipolar stepper motors in multiple motor systems. This application
More informationAN2361 Application note
AN2361 Application note Interfacing with the STR91x software library using Configuration and Programming Software (CAPS) Introduction STR91x microcontrollers offer extremely flexible configuration of I/O
More informationUSB dongle for the Bluetooth class 1 SPBT3.0DP1 module. Description
STEVAL-BTDP USB dongle for the Bluetooth class SPBT.0DP module Data brief Features Based on the V.0 Bluetooth class module SPBT.0DP USB interface and power supply Reprogramming support via USB interface
More informationAN3964 Application note
Application note STM32L1x temperature sensor example Introduction This application note describes a method of implementing a simple application for temperature measurement using the STM32L-DISCOVERY and
More informationUSB dongle for the Bluetooth class 2 SPBT3.0DP2 module. Description
STEVAL-BTDP USB dongle for the Bluetooth class SPBT.0DP module Data brief Features Based on the V.0 Bluetooth class module SPBT.0DP USB interface and power supply Reprogramming support via USB interface
More informationSTMicroelectronics. STxP70-4 assembler. User manual Rev A. October
STMicroelectronics STxP70-4 assembler User manual 8229631 Rev A October 2009 www.st.com BLANK User manual STxP70-4 assembler Introduction The STxP70-4 version of the assembler is based upon the GNU assembler
More informationAN2408 Application note
Application note 900mA standalone linear Li-Ion battery charger with thermal regulation Introduction One way to minimize the size and complexity of a battery charger is to use a linear-type charger. The
More informationAN2936 Application note
Application note 0 W SMPS with HV power MOSFET and the L6565 for three-phase industrial applications Introduction This document introduces a solution for industrial power supplies fed by a three-phase
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. ST7xxxx-SK/RAIS Raisonance s complete, low-cost starter kits for ST7 The
More informationAN2202 Application note
Application note STR73x microcontroller power management Introduction This application note provides an overview of the STR73x power management features and gives some guidelines for using the low power
More information