Harvatek International 0.4 Quad Digit Clock Display HCD89010

Transcription

1 Harvatek International.4 Quad Digit Clock Display Official Product Customer Part No Data Sheet No. **************** **************** Oct Version of 1.8 Page 1/7

2 Revision History Revision Page Version No. Revision Date DS original CHANGE PACKAGE DIMENSIONS CHANGE LED Change REF height and digit Add Customer P/N Add ESD Change ELECTRICAL / OPTICAL CHARACTERISTICS Change packing Change LED IV Official Product Customer Part No Data Sheet No. **************** **************** Oct Version of 1.8 Page 2/7

3 DISCLAIMER This is a.4 inch(1mm) digit height quadruple digit seven-segment display. This device utilizes white SMD LED,and has a black face and white segments. FEATURES *.4 inch(1.mm) DIGIT HEIGHT *CONTINUOUS UNIFORM SEGMENTS *LOW POWER REQUIREMENT *EXCELLENT CHARACTERS APPEARANCE *HIGH BRIGHTNESS & HIGH CONTRAST *WIDE VIEWING ANGLE *SOLID STATE RELIABILITY *CATEGORIZED FOR LUMINOUS INTENSITY Official Product Customer Part No Data Sheet No. **************** **************** Oct Version of 1.8 Page 3/7

4 6 6.5± PACKAGE DIMENSIONS.4 Quad Digit Clock Display PIN 16 PIN 1 6 PIN1 PART NO DATE CODE BIN CODE F E DIGIT 1 A G A C D G B DP C DIGIT 2 DIGIT 3 L1 DIG.1 DIG.2 DIG.3 L1 L2 DIGIT 4 L3 DIG.4 PART NO DATE CODE D DP1 DP2 DP3 DP4 NOTES: 1. All dimensions are in millimeters(inches), Tolerance is mm(.1inch)unless other wise noted. 2. Specifications are subject to change without notice. 2.54*7= The gap between the reflector and PCB shall not exceed.25mm. INTERNAL CIRCUIT DIAGRAM 1.16 DIGIT 1 DIGIT 2 DIGIT 3 DIGIT A B C D E F G DP A B C D E F G DP L1 L2 L3 A B C D E F G DP A B C D E F G DP ,12 no pin,pin 9 NC Official Product Customer Part No Data Sheet No. **************** **************** Oct Version of 1.8 Page 4/7

5 ABSOLUTE MAXIMUM RATING AT Ta = 25 PARAMETER MAXIMUM RATING UNIT Power Dissipation Per Segment 78 mw Continuous Forward Current Per Segment 2 ma Reverse Voltage Per Segment 5 V Operating Temperature Range Storage Temperature Range Electrostatic Discharge Threshold(HBM)Note -35 to to+85 1V Soldering Conditions: 1/16 inch below seating plane for 3 seconds at 26 Remarks:This product should be operated in forward bias.if a reverse voltage is continuously applied to the product, such operation can cause migration resulting in LED damage. ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25oC LED DISPLAY PARAMETER SYMBOL MIN. TYP. MAX. TYP Max UNIT TEST CONDITION Average Luminous Intensity Iv mcd IF=5mA Peak Emission Wavelength X Spectral Line Half-Width Y nm IF=5mA Forward Voltage Per Segment VF V IF=5mA Reverse Current Per Segment IR ua VR=5V Luminous Intensity Matching Ratio Iv-m :2 IF=5mA Note:Luminous intensity is measured with a light sensor and filter combination that approximates the CIE (Commision Internationale De L Eclairage) eye-response curve. Official Product Customer Part No Data Sheet No. **************** **************** Oct Version of 1.8 Page 5/7

6 Forward Current LF(mA) Relative Luminous Intensity Forward Current LF(mA) Luminous Intensity Relative Value at LF=1mA.4 Quad Digit Clock Display TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES 1. RELATIVE INTENSITY VS WAVELENGTH Wavelength(nm) 1 IF~ VF 3. IV~ IF Forward Voltage VF(V) Forward Current IF(mA) 5 IF~ Ta 2. IV~ Ta Ambient TemperatureTa( ) Ambient Temperature Ta( ) Official Product Customer Part No Data Sheet No. **************** **************** Oct Version of 1.8 Page 6/7

7 Packing Flow: product 24pcs per outside carton 12PCS per tube 4pcs inner carton per outside carton 6pcs tube per inner carton Remark :Tube Inner carton and outer carton of label need stick on client P/N Official Product Customer Part No Data Sheet No. **************** **************** Oct Version of 1.8 Page 7/7