Intrusion Detection Technology SafeKey Switching Module SSM/A, SSM/U Product Manual

Transcription

1 Intrusion Detection Technology SafeKey Switching Module SSM/A, SSM/U Product Manual

2

3 ABB i-bus KNX Contents Contents Page 1 General Using the product manual Note Product and functional overview Description of the inputs and outputs Operating controls Device Technology SafeKey Switching Module SSM/A, SSM/U Technical data Circuit diagram Dimension drawing Assembly and installation Commissioning Creating chipkeys/keypad codes Creating the programming key Creating chipkeys Creating the keypad code Creating a code combination (chipkey and keypad code) Creating chipkeys/keypad codes Deleting the chipkey Deleting the keypad code or code combination Delete all chipkeys Deleting all keypad codes and code combinations Function Set/Unset request Setting Direct setting Setting with chipkey Setting with keypad code Setting with code combination Delayed setting Setting with chipkey Setting with keypad code Setting with code combination Unsetting Unsetting with direct setting Unsetting with chipkey Unsetting with keypad code Unsetting with code combination Unsetting with delayed setting Unsetting with chipkey Unsetting with keypad code Unsetting with code combination Function Potential-free switching Time inhibit...25 A Appendix A.1 Direct setting flow chart...27 A.2 Delayed setting flow chart...27 A.3 ETS parameters in the Security Terminal...28 A.4 Ordering Information...34 A.5 Notes...35 SSM/x 2CDC D0201 i

4

5 ABB i-bus KNX General 1 General The SafeKey Switching Module ensures simple connection and evaluation of a SafeKey Wall Reader with and without a keypad for potential-free switching of electrical components or when transferring a set/unset request. 1.1 Using the product manual This manual provides you with detailed technical information relating to the function, installation and programming of the SafeKey Switching Module. The application of the device is explained using examples. This manual is divided into the following sections: Chapter 1 General Chapter 2 Device technology Chapter 3 Commissioning Chapter A Appendix Note Notes and safety instructions are represented as follows in this manual: Note Tips for usage and operation Examples Application examples, installation examples, programming examples Important These safety instructions are used as soon as there is danger of a malfunction without risk of damage or injury. Caution These safety instructions are used as soon as there is danger of a malfunction without risk of damage or injury. Danger These safety instructions are used if there is a danger for life and limb with inappropriate use. Danger These safety instructions are used if there is a danger to life with inappropriate use. SSM/x 2CDC D0201 3

6 ABB i-bus KNX General 1.2 Product and functional overview Description of the inputs and outputs The SafeKey Switching Module features two inputs and two outputs. The input (+ / D / P / -) is used for connection of a SafeKey Wall Reader with or without keypad. Connection is implemented with the 4-core cable of the Wall Reader. The maximum cable length is six metres. The connection cable is connected to the terminals (+ / D / P / -), see 1Circuit diagram, page 9. Input C is used for evaluation of the external or internal setting status information of the Security Terminal MT/x. The evaluation is used for control of the buzzer in the SafeKey Wall Reader, see ETS parameters in the Security Terminal, page 28. For further information see: Function Set/Unset request, page 19 Note The evaluation of input C is only undertaken with the function Set/Unset request. With function potentialfree switching, input C does not have a function. Output E is used for transferring a set/unset request to the Security Terminal MT/x. The output is a normally closed (N.C.) contact with an integrated resistor combination of 2.7 kohm and 560 Ohm. The normally closed contact is switched in parallel to a 560 Ohm resistor, so that a resistance value of 2.7 kohm is present on the terminals when the contact is closed, and 3.26 kohm is present when the contact is opened. The integrated resistor combination is used on the one hand as a setting line for the Security Terminal and on the other hand as a tamper monitoring feature (disconnection or short circuit) for the cable between the SafeKey Switching Module and the Security Terminal. Output F is used for potential-free switching of electrical components, e.g. door openers or garage doors. Depending on the connection, the output can be used as a normally closed (N.C.) or normally open (N.O.) contact, see 1Circuit diagram, page 9. Caution Output F has a maximum switching current rating of 5 A! The device can be destroyed if the max. switching current is exceeded. 4 2CDC D0201 SSM/x

7 ABB i-bus KNX General Operating controls The SafeKey Switching Module has many functions that can be set via DIP switch. DIP switch function overview: DIP switch Function at ON Function at OFF 1 Set/Unset request Potential-free (floating) switching 2 Control time of the relay s (fine adjustment via rotary potentiometer). Only with the function potential-free switching. Control time of the relay 1 10 s (fine adjustment via rotary potentiometer). Only with the function potential-free switching 3 Delayed setting Direct setting 4 Dynamic* control of the relay Static** control of the relay 5 Switch-in of the integrated resistor combination for function set/unset request on output E * Dynamic control = relay operates with pushbutton behaviour ** Static control = relay operates with switching behaviour Switch off of the integrated resistor combination for function potential-free switching on output F The following settings are possible: Function Set/Unset request via output E DIP 1 (ON): DIP 2 (OFF): DIP 3 (OFF): DIP 4 (OFF): DIP 5 (ON): Set/Unset request No function Direct setting Static control of the relay Integrated resistor combination DIP 1 (ON): DIP 2 (OFF): DIP 3 (OFF): DIP 4 (ON): DIP 5 (ON): Set/Unset request No function Direct setting Dynamic control of the relay Integrated resistor combination DIP 1 (ON): DIP 2 (OFF): DIP 3 (ON): DIP 4 (ON): DIP 5 (ON): Set/Unset request No function Delayed setting Dynamic control of the relay Integrated resistor combination SSM/x 2CDC D0201 5

8 ABB i-bus KNX General Function Potential-free switching via output F DIP 1 (OFF): DIP 2 (OFF): DIP 3 (OFF): DIP 4 (OFF): DIP 5 (OFF): Function potential-free switching Control time of the relay 1 10 s (fine adjustment via rotary potentiometer). No function No function No function DIP 1 (OFF): DIP 2 (ON): DIP 3 (OFF): DIP 4 (OFF): DIP 5 (OFF): Function potential-free switching Control time of the relay s (fine adjustment via rotary potentiometer). No function No function No function Programming button The programming button is used for creating the programming key and/or deleting the memory of the SafeKey Switching Module. Rotary potentiometer The rotary potentiometer is used for fine adjustment of the relay control time with the function potential-free switching. DIP switch Position Position of the rotary potentiometer Control time of the relay 2 OFF Left end limit 1 s 2 OFF Right end limit 10 s 2 ON Left end limit 10 s 2 ON Right end limit 100 s The range between the left and right limits is used for fine adjustment of the relay control time. 6 2CDC D0201 SSM/x

9 ABB i-bus KNX Device Technology 2 Device Technology 2.1 SafeKey Switching Module SSM/A, SSM/U SSM/A 2CDC S0011 The SafeKey Switching Module enables simple connection and evaluation of a SafeKey Wall Reader to the MT/x. This can be undertaken with and without a code keypad (WEL or WELT). The module can be used either for potential-free switching of electrical components up to 5 A at maximum V DC/AC, e.g. electrical door openers or garage doors, or for transferring a set/unset request to the Security Terminal MT/x. The switching procedure or the set/unset request can be initiated via the chipkey and/or via a code entry. The module is suitable for flush mounting and surface mounting, depending on the housing design. A 12 V power supply is required. 2.2 Technical data Supply Inputs Outputs Connection terminals Operating controls Supply voltage Current consumption Number SafeKey Wall Reader connection Acknowledgement input Number Type Output E Output F Maximum switching current Maximum switching voltage Screw terminals Tightening torque Programming button Rotary potentiometer DIP switch 12 V DC/AC ±1.6 V < 5 ma (typical) maximum 50 ma with relay control 2 (+ / D / P / -) Potential-free (floating) or max. 12 V DC Terminal C1: + Terminal C2: - 2 Monostable relay For set/unset request with integrated resistor combination (2.7 kohm Ohm) For potential-free switching of electrical components, e.g. door openers or garage doors 5 A V DC/AC mm² stranded mm² solid core Multi-core connection capacity (same cross-section) mm² stranded mm² solid core Maximum 0.25 Nm For creation of the programming key or deleting the memory of the Module For fine adjustment of the relay control time with the function potential-free switching For selection of the module functionality SSM/x 2CDC D0201 7

10 ABB i-bus KNX Device Technology Enclosure IP 30 To EN Safety class II To EN Temperature range Operation -5 C +45 C Transport -25 C +70 C Storage -25 C +55 C Ambient conditions Maximum air humidity 93 %, no condensation allowed Design PCB in enclosure (SM or FM) Dimensions in (H x W x D) Enclosure SM (50 x 114 x 26) Enclosure FM (50 x 114 x 21) Cover FM (70 x 134 x 4) Installation Flush mounting (SSM/U) Surface mounting (SSM/A) Mounting position As required Weight Housing/colour CE mark Module with flush mounting enclosure Module with surface mounting enclosure Plastic, halogen-free, white In accordance with the EMC guideline and low voltage guideline 0.08 kg 0.07 kg 8 2CDC D0201 SSM/x

11 ABB i-bus KNX Device Technology 2.3 Circuit diagram 1 Power supply 12 V DC/AC 2 DIP switch 3 Output E for set/unset request 4 Output F for potential-free switching 5 Acknowledge input C 6 Programming button 7 Rotary potentiometer 8 SafeKey Wall Reader connection (+ / D / P / -) SSM/x 2CDC D0201 9

12 ABB i-bus KNX Device Technology 2.4 Dimension drawing 2CDC F0010 2CDC F0010 2CDC F CDC D0201 SSM/x

13 ABB i-bus KNX Device Technology 2.5 Assembly and installation The device is suitable for flush mounting and surface mounting, depending on the housing design. The electrical connection is implemented using screw terminals. The terminal assignment is located on the housing. The device is ready for operation after the SafeKey Wall Reader and the supply voltage have been connected. Accessibility to the device for the purpose of operation, testing, visual inspection, maintenance and repair must be provided compliant to VDE Commissioning requirements The installation and commissioning may only be carried out by qualified electrical specialists. The appropriate norms, guidelines, regulations and specifications for your country should be observed when planning and setting up electrical installations and security systems for intrusion and fire detection. Protect the device from damp, dirt and damage during transport, storage and operation. Only operate the device within the specified technical data limits! The device should only be operated in an enclosed housing (distribution board)! The voltage supply to the device must be switched off, before mounting work is performed. Cleaning If a device becomes dirty, it can be cleaned using a dry cloth or a cloth dampened with a soapy solution. Corrosive agents or solutions should never be used. Maintenance The device is maintenance-free. No repairs should be carried out by unauthorised personnel if damage occurs, e.g. during transport and/or storage. SSM/x 2CDC D

14

15 ABB i-bus KNX Commissioning 3 Commissioning 3.1 Creating chipkeys/keypad codes Before a chipkey or a keypad code can be created in the memory of the SafeKey Switching Module, the programming key must be created. Any chipkey can be used as the programming key. The module can manage 512 chipkeys or keypad codes including the programming key. Important Only one programming key can be created per SafeKey Switching Module. However, with several SafeKey Switching Modules, the same programming key can be created. SSM/x 2CDC D

16 ABB i-bus KNX Commissioning Creating the programming key Press programming button, until a continuous tone can be heard from the Wall Reader. When this tone sounds, insert a chipkey into the key reader and remove it again. This process teaches-in the chipkey as the programming key in the SafeKey Switching Module. It is recommended that you assign a special marking to this chipkey. New chipkeys or keypad codes can only be created using the programming key. Caution By pressing the programming button, the entire memory content of the SafeKey Switching Module is deleted, i.e. all the chipkeys, keypad codes, code combinations and the programming key used up to now are irretrievably deleted. Press the programming button, until a continuous tone is heard. During this continuous tone, insert a chipkey into the key reader and remove it again. 1 x The continuous tone stops. The chipkey has now been teached-in as a programming key. ABB Mark the programming key accordingly, e.g. P for programming key. Important If a programming key is lost, a new programming key must be created. For this purpose, proceed as described in chapter Creating the programming key, page CDC D0201 SSM/x

17 ABB i-bus KNX Commissioning Creating chipkeys In order to create a new chipkey, the programming key and a chipkey unknown to the system are required. Insert the programming key into the key reader and remove it again. 1 x A slow intermittent tone will sound for about 6 s. The module is now in programming mode. During this signal tone, insert any chipkey into the key reader and remove it again. The signal tone stops. The chipkey has been created. 1 x Creating the keypad code The programming key is required to create a new keypad code. Insert the programming key into the key reader and remove it again. 1 x A slow intermittent tone will sound for about 6 s. The module is now in programming mode. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU 0 WZ STOP PROG Enter any 6-digit keypad code (keys 0 9) during the signal tone. The signal tone ceases, when the first key is pressed. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU 0 WZ STOP PROG Press the PROG key, after you have entered the keypad code. The keypad code has been created. SSM/x 2CDC D

18 ABB i-bus KNX Commissioning Creating a code combination (chipkey and keypad code) In order to create a code combination, the programming key and a known or unknown chipkey are required. Insert the programming key into the key reader and remove it again. 1 x A slow intermittent tone will sound for about 6 s. The module is now in programming mode. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU 0 WZ Enter any 5-digit keypad code (keys 0 9) during the signal tone. The signal tone ceases, when the first key is pressed. STOP PROG Insert the known/unknown chipkey and remove it again. A code combination con- sisting of keypad code and chipkey has been created. 1 x Note Use of the code combination offers the following benefits should a chipkey be mislaid or lost: The chipkey can be deleted from the memory using the keypad code. 16 2CDC D0201 SSM/x

19 ABB i-bus KNX Commissioning 3.2 Deleting chipkeys/keypad codes Deleting the chipkey In order delete a chipkey, the programming key and the chipkey to be deleted are required. 2 x Insert and remove the programming key twice consecutively into the key reader. A fast intermittent tone will sound. The module is now in deleting mode. Insert the chipkey to be deleted into the key reader and remove it. The chipkey has been deleted. 1 x Deleting the keypad code or code combination A programming key is required to delete a keypad code or a code combination. 2 x Insert and remove the programming key twice consecutively into the key reader. A fast intermittent tone will sound. The module is now in deleting mode. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU 0 WZ STOP PROG Enter the keypad code or the keypad code of the code combination to be deleted during the signal tone. The signal tone ceases, when the first key is pressed. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU 0 WZ STOP PROG After entering the keypad code or the code of the code combination to be deleted, press the PROG key on the Wall Reader. The keypad code or the code combination (chipkey and keypad code) are deleted. SSM/x 2CDC D

20 ABB i-bus KNX Commissioning Delete all chipkeys The programming key is required to delete all chipkeys. 3 x Insert and remove the programming key three times consecutively into the key reader. A continuous tone sounds. Insert the programming key into the key reader and remove it again. The continu- ous tone stops. All chipkeys have been deleted. 1 x Deleting all keypad codes and code combinations A programming key is required to delete all keypad codes or code combinations. 3 x Insert and remove the programming key three times consecutively into the key reader. A continuous tone sounds. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU 0 WZ Press any key (keys 0 9). The continuous tone stops. All keypad codes and code combinations have been deleted. STOP PROG 18 2CDC D0201 SSM/x

21 ABB i-bus KNX Commissioning 3.3 Function Set/Unset request The function Set/Unset request is used to set and unset the Security Terminal MT/x Setting A differentiation is made between two methods when setting: Direct setting For direct setting, the Security Terminal MT/x is switched set and unset from outside the premises by the user. Delayed setting For delayed setting, the Security Terminal MT/x is switched set and unset from inside the premises by the user. Note In order to ensure that an alarm is not triggered during a setting attempt, the user has a certain time (delay time) to exit the premises after a setting attempt. During unsetting, the user once again has a certain time (alarm delay) to unset the alarm at the Security Terminal, after they have entered the premises Direct setting There are different ways of direct setting: with chipkey with keypad code with code combination Important For direct setting, the acknowledgement input C must be switched with the status information external set or internal set of the Security Terminal, e.g. via an available relay output of the Security Terminal. No signal may be present on the acknowledgement input C in the unset state of the Security Terminal, i.e. the input may not be bypassed and 12 V DC may not be applied. A signal must be present on the acknowledgement input C in the set state of the Security Terminal, i.e. the input must be bypassed or 12 V DC must be applied. SSM/x 2CDC D

22 ABB i-bus KNX Commissioning Setting with chipkey Note With static control (switching behaviour) of the relay, the contact with successful setting is closed, until it is unset. The contact is re-opened if setting is unsuccessful. With dynamic control (pushbutton behaviour) of the relay, the contact is opened and closed again for about 1.5 s both for the setting and the unsetting request. 2 x Insert and remove the teached-in chipkey twice consecutively in the key reader. With successful setting, a long continuous tone sounds for about 2.5 s. (A signal is present on acknowledgement input C). With a non-successful setting, a fast intermittent tone sounds for about 2 s. (No signal is present on acknowledgement input C) Setting with keypad code 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (6-digit). 0 WZ STOP PROG 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU 0 WZ Press the PROG button after entering the code. STOP PROG With successful setting, a long continuous tone sounds for about 2.5 s. (A signal is present on acknowledgement input C). With a non-successful setting, a fast intermittent tone sounds for about 2 s. (No signal is present on acknowledgement input C). 20 2CDC D0201 SSM/x

23 ABB i-bus KNX Commissioning Setting with code combination 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (5-digit). 0 WZ STOP PROG 2 x Insert and remove the teached-in chipkey twice consecutively in the key reader. With successful setting, a long continuous tone sounds for about 2.5 s. (A signal is present on acknowledgement input C). With a non-successful setting, a fast intermittent tone sounds for about 2 s. (No signal is present on acknowledgement input C) Delayed setting There are different ways of delayed setting: with chipkey with keypad code with code combination Important With delayed setting, the acknowledgement input C evaluates the delay or alarm time of the Security Terminal, i.e. as soon as a signal is present on the acknowledgement input C, the buzzer on the Safe- Key Wall Reader is controlled. The continuous tone continues as long as a signal is present on acknowledgement input C. Note With dynamic control (pushbutton behaviour) of the relay, the contact is opened and closed again for about 1.5 s both for the setting and the unsetting request. SSM/x 2CDC D

24 ABB i-bus KNX Commissioning Setting with chipkey Insert and remove the teached-in chipkey once in the key reader. 1 x During the delay time, a continuous tone is sounded (duration is determined from the Security Terminal via the communication object Delay time is active). A continuous tone is not sounded if the delay time has not been triggered Setting with keypad code 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (6-digit). 0 WZ STOP PROG During the delay time, a continuous tone is sounded (duration is determined from the Security Terminal via the communication object Delay time is active). A continuous tone is not sounded if the delay time has not been triggered Setting with code combination 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (5-digit). 0 WZ STOP PROG Insert and remove the teached-in chipkey once in the key reader. 1 x During the delay time, a continuous tone is sounded (duration is determined from the Security Terminal via the communication object Delay time active). A continuous tone is not sounded if the delay time has not been triggered. 22 2CDC D0201 SSM/x

25 ABB i-bus KNX Commissioning Unsetting A differentiation is made between two methods when unsetting: Unsetting with direct setting For direct setting, the Security Terminal is switched unset from outside the premises by the user. Unsetting with delayed setting For delayed setting, the Security Terminal is switched unset from inside the premises by the user Unsetting with direct setting There are different ways of unsetting with direct setting: with chipkey with keypad code with code combination Unsetting with chipkey Insert and remove the teached-in chipkey once in the key reader. 1 x When unsetting is successful, a short tone sounds for about 0.5 s. Unsetting only occurs if there is no longer a signal on acknowledgement input C. With a non-successful unsetting, a fast intermittent tone sounds for about 2 s. (A signal is still present on acknowledgement input C) Unsetting with keypad code 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (6-digit). 0 WZ STOP PROG When unsetting is successful, a short tone sounds for about 0.5 s. Unsetting only occurs if there is no longer a signal on acknowledgement input C. With a non-successful unsetting, a fast intermittent tone sounds for about 2 s. (A signal is still present on acknowledgement input C). SSM/x 2CDC D

26 ABB i-bus KNX Commissioning Unsetting with code combination 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (5-digit). 0 WZ STOP PROG Insert and remove the teached-in chipkey once in the key reader. 1 x When unsetting is successful, a short tone sounds for about 0.5 s. Unsetting only occurs if there is no longer a signal on acknowledgement input C. With a non-successful unsetting, a fast intermittent tone sounds for about 2 s. (A signal is still present on acknowledgement input C) Unsetting with delayed setting There are different ways of unsetting with delayed setting: with chipkey with keypad code with code combination Unsetting with chipkey During the alarm delay, a continuous tone is sounded (duration is determined from the Security Terminal via the communication object Alarm delay active). A continuous tone is not sounded if the alarm delay has not been triggered. Insert and remove the teached-in chipkey once in the key reader. 1 x 24 2CDC D0201 SSM/x

27 ABB i-bus KNX Commissioning Unsetting with keypad code During the alarm delay, a continuous tone is sounded (duration is determined from the Security Terminal via the communication object Alarm delay is active). A continuous tone is not sounded if the alarm delay has not been triggered. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (6-digit). 0 WZ STOP PROG Unsetting with code combination During the alarm delay, a continuous tone is sounded (duration is determined from the Security Terminal via the communication object Alarm delay active). A continuous tone is not sounded if the alarm delay has not been triggered. 1 AB 2 CD 3 EF 4 GHI 5 KL 6 MN 7 OP 8 RS 9 TU Enter the teached-in keypad code (5-digit). 0 WZ STOP PROG Insert and remove the teached-in chipkey once in the key reader. 1 x 3.4 Function Potential-free switching The function potential-free switching is used if electrical components are controlled via output F. 1 x Insert and remove the teached-in chipkey once in the key reader. Output F is controlled. The control time is dependent on the set function Time as well as on the adjustment of the rotary potentiometer, see Operating elements, page 5. This function can also be undertaken by using a keypad code or a code combination. 3.5 Time inhibit After the keypad code has be entered incorrectly several times (6-digit code 13 times), a 10 minute time inhibit occurs. A valid keypad code can no longer be accepted during the time inhibit. A triggered inhibit time will be indicated by a short recurring signal tone. SSM/x 2CDC D

28

29 ABB i-bus KNX Appendix A Appendix A.1 Direct setting flow chart Unset request Set acknowledgement Set request 1. Waiting for set acknowledgement on acknowledgement input C T 3s 2x 1x T >3 s Fault setting A.2 Unset acknowledgement Delayed setting flow chart Set request Signalization Delay time Finish Delay time Signalization Delay time 1. Alarm Delay active? yes 1x no Unset request 1x Unset request 1x SSM/x 2CDC D

30 ABB i-bus KNX Appendix A.3 ETS parameters in the Security Terminal The following examples should provide an overview of the respective ETS parameters of the Security Terminal that are required for the function Set/Unset request of the SafeKey Switching Module. Direct setting with static control of the relay: DIP 1 (ON): DIP 2 (OFF): DIP 3 (OFF): DIP 4 (OFF): DIP 5 (ON): Set/Unset request No function Direct setting Static control of the relay Integrated resistor combination The following parameters must be set in the Setting/Unsetting parameter window. Mode of setting/unsetting the system: normal Period of message setting confirmation : can be freely selected Period of message Unsetting confirmation : can be freely selected Period of message "Error during setting": can be freely selected 28 2CDC D0201 SSM/x

31 ABB i-bus KNX Appendix In parameter window Zone x, in the example shown Zone A, the following parameters must be set. Input: Setting/Unsetting input Behaviour: Switch Function: Monitored N/C contact (2.7 kohm Ohm) Type of setting/unsetting: External setting/unsetting Set minimum signal time manually: no Note The function Monitored N/C contact (2.7 kohm Ohm) is used for tampering detection of the setting input, i.e. the line is monitored, and if there is an open circuit or short-circuits between the SafeKey Switching Module and Security Terminal, a tampering alarm is issued. In parameter window Output x, in the example shown Output 1, the following parameters must be set. Operating mode of output: via device state Select device state: Externally set Enable time function: no Invert output: no SSM/x 2CDC D

32 ABB i-bus KNX Appendix Direct setting with dynamic control of the relay: DIP 1 (ON): DIP 2 (OFF): DIP 3 (OFF): DIP 4 (ON): DIP 5 (ON): Set/Unset request No function Direct setting Dynamic control of the relay Integrated resistor combination The following parameters must be set in the Setting/Unsetting parameter window. Mode of setting/unsetting the system: normal Period of message Setting confirmation : can be freely selected Period of message Unsetting confirmation : can be freely selected Period of message "Error during setting": can be freely selected In parameter window Zone x, in the example shown Zone A, the following parameters must be set. Input: Setting/Unsetting input Behaviour: Button Function: Monitored N/C contact (2.7 kohm Ohm) Type of setting/unsetting: External setting/unsetting Set minimum signal time manually: no Note The function Monitored N/C contact (2.7 kohm Ohm) is used for tampering detection of the setting input, i.e. the line is monitored, and if there is an open circuit or short circuits between the SafeKey Switching Module and Security Terminal, a tampering alarm is issued. 30 2CDC D0201 SSM/x

33 ABB i-bus KNX Appendix In tab Output x, in the example shown Output 1, the following parameters must be set. Operating mode of output: via device state Select device state: Externally set Enable function time: no Invert output: no SSM/x 2CDC D

34 ABB i-bus KNX Appendix Delayed setting with dynamic control of the relay: DIP 1 (ON): DIP 2 (OFF): DIP 3 (ON): DIP 4 (ON): DIP 5 (ON): Set/Unset request No function Delayed setting Dynamic control of the relay Integrated resistor combination The following parameters must be set in the Setting/Unsetting parameter window. Mode of setting/unsetting the system: delayed Setting Delay in s [1 3600]: 30 (this value must be adapted to suit the application) Alarm Delay in s [1 3600]: 30 (this value must be adapted to suit the application) All other parameters can be individually set here. 32 2CDC D0201 SSM/x

35 ABB i-bus KNX Appendix In parameter window Zone x, in the example shown Zone A, the following parameters must be set. Input: Setting/Unsetting input Behaviour: Buttons Function: Monitored N/C contact (2.7 kohm Ohm) Type of setting/unsetting: external setting/unsetting Set minimum signal time manually: no Note The function Monitored N/C contact (2.7 kohm Ohm) is used for tampering detection of the setting input, i.e. the line is monitored, and if there is an open circuit or short-circuits between the SafeKey Switching Module and Security Terminal, a tampering alarm is issued. In parameter window Output x, in the example shown Output 1, the following parameters must be set. Operating mode of output: via device state Select device state: Delay time is active Enable time function: no Invert output: no SSM/x 2CDC D

36 ABB i-bus KNX Appendix A.4 Ordering Information Device type Product name Order code bbn EAN Price group Weight 1 pcs [kg] SSM/A SafeKey Switching Module, SM 2CDG R P SSM/U SafeKey Switching Module, FM 2CDG R P WEL/A, ES SafeKey Wall Reader, Stainless GHQ R P steel WELT/A, ES SafeKey Wall Reader with Keypad, GHQ R P Stainless steel WELT/A, MC SafeKey Wall Reader with Keypad, GHQ R P Matt chrome-plated SCS SafeKey Chipkey GHQ R P Packaging [pc.] 34 2CDC D0201 SSM/x

37 ABB i-bus KNX Appendix A.5 Notes SSM/x 2CDC D

38 ABB i-bus KNX Appendix Notes 36 2CDC D0201 SSM/x

39

40 Contact ABB STOTZ-KONTAKT GmbH Eppelheimer Straße Heidelberg, Germany Phone: +49 (0) (Marketing) +49 (0) (KNX Helpline) Fax: +49 (0) Further information and local contacts: Note: We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG shall not be liable for any consequences arising from errors or incomplete information in this document. We reserve the rights to this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its content in whole or in parts is forbidden without prior written consent of ABB AG. Order number 2CDC D0201 (09.11) Copyright 2011 ABB All rights reserved