Skullcandy Air Raid USB Board Replacement

Size: px

Start display at page:

Download "Skullcandy Air Raid USB Board Replacement"

Imogene Allen
5 years ago
Views:

1 Skullcandy Air Raid USB Board Replacement The USB port should be replaced if it is visibly broken or the device will no longer charge. Written By: Cyrene ifixit CC BY-NC-SA Page 1 of 12

2 INTRODUCTION In this guide, we will take the Skullcandy Air Raid apart so that the USB motherboard can be replaced. TOOLS: Phillips #00 Screwdriver (1) ifixit Opening Tools (1) Phillips #000 Screwdriver (1) T6 Torx Screwdriver (1) ifixit CC BY-NC-SA Page 2 of 12

Step 2 Handle Using the T-6 hexagonal screwdriver, unscrew the four 10mm

3 Step 1 Rubber Cover Starting with the corners, gently pull the rubber cover off of the device. Step 2 Handle Using the T-6 hexagonal screwdriver, unscrew the four 10mm #6 hex screws on the right side of the device. Remove the handle from the device. ifixit CC BY-NC-SA Page 3 of 12

Step 4 Gently pull the sides of the front plate outwards from the device.

4 Step 3 Front Plate Unscrew the two screws on the left side of the device using the phillips #00 screwdriver. One 5mm Phillips screw. One 8mm Phillips screw. Step 4 Gently pull the sides of the front plate outwards from the device. Pull up on the front plate to remove it from the device. ifixit CC BY-NC-SA Page 4 of 12

Step 6 Using the plastic opening tool, pry around edges of the speaker to loosen glue contact with front

5 Step 5 Speakers Using a #000 Philips Screwdriver, unscrew the four 8 mm Philips screws from each corner of both speakers (eight 8 mm Philips screws total). Step 6 Using the plastic opening tool, pry around edges of the speaker to loosen glue contact with front plate. If you are unable to loosen glue contact using the plastic opening tool, use a heat gun to assist in removal. ifixit CC BY-NC-SA Page 5 of 12

For reassembly, ensure proper orientation of the cable plug.

6 Step 7 Lift the speaker out of the device. Be aware of the connection with the ribbon cable. For reassembly, ensure proper orientation of the cable plug. Step 8 Firmly pull on the end of ribbon cable to disconnect the speaker from the motherboard. ifixit CC BY-NC-SA Page 6 of 12

the panel, above and below volume buttons.

7 Step 9 Control Buttons Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the middle of the panel, above and below volume buttons. Step 10 Lift the button panel. ifixit CC BY-NC-SA Page 7 of 12

8 Step 11 Button Motherboard Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the button motherboard. Step 12 Using a plastic opening tool, pry the button motherboard to detach it from the device. The button motherboard is connected to a ribbon cable inside the device. ifixit CC BY-NC-SA Page 8 of 12

Step 13 Ribbon Cable Pull the black ribbon cord attachment away from the

Pull on the cable until it releases from the back of the The black

will not disconnect from the Step 14 Back panel Using a Phillips #00

9 Step 13 Ribbon Cable Pull the black ribbon cord attachment away from the motherboard. Pull on the cable until it releases from the back of the motherboard. The black attachment is part of the connector, not the blue ribbon cable, so it will not disconnect from the motherboard. Step 14 Back panel Using a Phillips #00 Precision Screwdriver, unscrew two 8 mm screws. Lift off the back panel. ifixit CC BY-NC-SA Page 9 of 12

10 Step 15 Ribbon Cables Where the blue and white ribbon cable meets the motherboard, pull up on the black piece of the ribbon cable connector. Pull the ribbon cable away from the motherboard. Step 16 Pull on grey and white ribbon cable until it disconnects from the motherboard. ifixit CC BY-NC-SA Page 10 of 12

Step 17 Left Divider Using a Phillips #00 Precision

divider between the main cavity and the USB

motherboard to slide left divider back in place.

11 Step 17 Left Divider Using a Phillips #00 Precision Screwdriver, unscrew two 6 mm screws from the left divider between the main cavity and the USB motherboard. Pull out the USB/On Switch panel. Pull out the Left Divider. For reassembly, lift up on right side of motherboard to slide left divider back in place. Step 18 USB Motherboard Using a Phillips #00 Precision Screwdriver, unscrew two 5 mm Phillips-head screws from the USB motherboard. Remove the metal clip. ifixit CC BY-NC-SA Page 11 of 12

12 To reassemble your device, follow these instructions in reverse order. This document was last generated on :51:05 PM. ifixit CC BY-NC-SA Page 12 of 12

Canon EOS Rebel T4i Motherboard

Canon EOS Rebel T4i Motherboard Replacement This guide will show you how to replace the motherboard on your Canon Rebel T4i. Written By: Jordan Rabold ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION