Contents. Before Using Product Composition

Transcription

1 User Guide

2 Contents Before Using Product Composition Name of each part QUAD LOCK Mounting & Type Smart Phone Mounting Gun Handle Removal & Mounting Displaying LED by Status Power ON & OFF Communication Mode Setting Barcode and RFID Setting Charging Device Charging Device (Using USB Port via PC) Charging Device (Using Cradle) Support Concurrent Charging of Smart Phone Using Bluetooth Data Communication Mode Using USB Data Communication Mode Bluetooth Connection with Android Phone Bluetooth Connection with iphone Bluetooth Connection with Windows USB Connection with Windows ATS100 Specifications Product Warranty The copyright of this manual can be found on ATID. Unauthorized use or reproduction of part or all of the contents of this manual without prior permission of ATID is prohibited. 2

3 Before Using - The following conventions are used throughout this document to convey certain information. - Technical Support via the Internet is available 24 hours per day, 365 days per year. - This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation In no event shall or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Charging Precautions Icons Used Caution Warns you of a situation where unpredictable happen or damage Caution Warns you of a potential water shock situtation Use damaged power supply may cause problem please replace it. Do not place heavy material near device and do not pull power supply hardly. 3

4 Do not place too many power supply at the same time (It may cause conflagration or electronic damage) Be careful not to let liquid or pull power supply. (It may cause failure and electronic damage) Precautions when Using Icons used Caution Warns you of a situation where unpredictable happen or damage Caution Warns you of a potential water shock situation Caution warns you of a ban on disassemble Do not use chemical on the device but wipe it out with smooth cloth or tower. Do not place the device next to heating equipment (It may cause conflagration or electronic damage.) 4

5 In cleaning, do not splash water. (It may cause conflagration or device failure.) Do not install the device in a place subject to direct sun light, humidity and dust. (It may cause conflagration or electronic damage.) Do not disassemble, fix device and remodel device manually. Atid Co.,Ltd. is not responsible for any damage to or loss Do not place a magnet near the product 5

6 Product Composition ATS100 Main Body Gun Handle (With Battery) USB Sync Cable (Type-C) User Guide & Warranty Strap Hand strap QUAD LOCK Mount (Option) QUAD LOCK Adapter (Option) Cradle (Optional item) Name of each part 5 1 Power Button 2 2 Switch to Communication 3 mode 3 Reset Button 4 4 Trigger 5 QUAD LOCK Connection Port 6 2D Barcode Scanner 7 UHF 8 Barcode / RFID Switch Button 9 Charge Indicator 8 10 Barcode / RFID Indicator 9 11 Communication Mode Indicator M Hand strap Hole 13 Sync Cable Connector Gun Handle Removal Button 15 Gun Handle (With Battery) 16 Cradle Connector Caution Do not connect any other such as USB than supplied QUAD LOCK to QUAD LOCK Connection port, it may cause malfunction of the Device. 6 16

7 QUAD LOCK Mounting 1 The QUAD LOCK contacts need to be face down at the top of the device to meet the contacts shown in the image right. 2 The QUAD LOCK direction to push is shown in the diagram right. 3 The QUAD LOCK can be locked into position image right. LOCK UNLOCK QUAD LOCK Type Type-C Micro USB We may provide USB Type-C and Micro USB. *The standard USB cable will be Type-C. 7

8 Smart Phone Mounting 1 Ensure the phone is fitted into its QUAD LOCK case before attaching the case to the ATS Make sure all of the contacts - on both the QUAD LOCK socket 3 Align the phone towards 45 degrees into the right place. 4 To put USB cable Phone USB Port. Notice If you don't want to use USB, it's not mandatory to use it. please note it. 8

9 Gun Handle Removal 1 Press removal button 2 Pull out the gun to the right side to release it 3 Pull up the gun to release completely. Warning Be careful your hand When you Control Gun Handle Gun Handle Mounting 1 The Gun Handle needs to be face down at the device to meet the right place as image. 2 Push the gun to the left side to mounting the gun 9

10 Displaying LED by Status Charging Indicator - Red LED Blink : Low Battery - Red LED ON : Charging - Green LED ON : Charging Complete Barcode / RFID Indicator - Blue LED ON : Barcode Mode - Blue LED Blink : Trigger Input Mode - Blue LED OFF : RFID Mode Charging Indicator Barcode / RFID Indicator Communication Mode Indicator Communication Mode Indicator - Green LED Blink : Bluetooth Mode - Red LED Blink : USB Mode Power ON Press Power Button ( ) for a second then release with beep. Power OFF Press Power Button ( ) for a second. Communication Mode Setting Press arrow ( ) button it can be connected Bluetooth or USB. (Swtiching mode will be taked a couple of seconds) Barcode and RFID setting Press M - Barcode mode, RFID and Trigger scanning mode. 10

11 Charging Device 1 Input Charging Cable to ATS100 (USB Connector should be over 5V/2A ) 2 Input Charging Connector to socket. Charging Device (Using USB Port via PC) 1 Input USB Connector to ATS100 2 Input USB Connector to PC Notice The Device will be Charging via PC however your Phone wouldn't be able to Charge at the same time. 11

12 Charging Device (Using Cradle) 1 Input Device to Cradle. 2 Input USB Connector behind Cradle. 3 Input Adapter to socket. Notice - Cradle and Charging Connector will be Optional Items. - If you would like to buy them please call us. Support Concurrent Charging of Smart Phone ATS100 and mobile into QUAD LOCK direct charging connection will allow to both simultaneously. Important - Some Devices may not be Charged. - While Charging can not be Communicated via USB. - Charging device and mobile at the same time, Charging speed will be affected slowly. - Do not allow to Charge into PC, if you want to Charge simultaneously please use Charger Adapter - It does not allow to Quick Charge 12

13 Using Bluetooth Data Communication Mode Important Ensure Bluetooth setting should be ok before trying to connect the reader. iphone - Using BLE Mode Android, Windows - Using SPP Mode or HID Mode (HID mode is not managed via ATS100 Demo App.) Communication Mode Indicator 1 With the trigger of the ATS100 pulled, press the power button ( ) to turn on the power. Indication by Bluetooth Mode - Green LED Blinks Fast : BLE Mode - Green LED remains ON : HID Mode - Green LED Blinks every 2 seconds : SPP Mode 2 Press the Communication Mode Toggle Button ( ) to Set Indicator to Blink/ON in Green. (Set to Bluetooth Mode) Trigger 3 Each time you press the Barcode / RFID Switch Button (M), the BLE / HID / SPP Mode Switches sequentially. 4 Press and hold the Power Button ( ) until the buzzer sounds to complete the Setting. 13

14 Using USB Data Communication Mode Important Ensure USB setting should be ok before trying to connect the reader. iphone - Unable to Support Android, Windows - Using VCP Mode or HID Mode (HID mode is not managed via ATS100 Demo App.) Communication Mode Indicator Indication by USB Mode - Red LED Blinks every 2 seconds : VCP Mode - Red LED remains ON : HID Mode 1 With the trigger of the ATS100 pulled, press the power button ( ) to turn on the power. 2 Press the Communication Mode Toggle Button ( ) to Set Indicator to Blink/ON in Red. (Set to USB Mode) Trigger 3 Each time you press the Barcode / RFID Switch Button (M), the VCP / HID Mode Switches sequentially. 4 Press and hold the Power Button ( ) until the buzzer sounds to complete the Setting. 14

15 Bluetooth Connection with Android Phone Ensure the ATID Application for Android is Installed the mobile. Installation SDK : Important Ensure the ATS100 Bluetooth Mode with SPP. (See setting Bluetooth on page13) Notice Before trying to connect to the mobile, it must be enabled from Android Ver. 4.2 (Jelly Bean). To be recommended ver.6.0(mashmallow) for activation. 1 Press the application. 2 Press "YES" to complete Bluetooth connection 06:59 X.X.X.XXXXXXXXXX Application is requesting permission to turn on Bluetooth Allow? NO YES 15

16 3 Press "New Device". 4 Press "Scan Device". 06:59 Regist Device 06:59 X.X.X.XXXXXXXXXX Bluetooth USB Paired Devices New Devices 5 Press the correct device on the New Devices list. 6 Press ( ) 06:59 07:00 Regist Device Bluetooth Paired Devices USB ATS100-XXXX XX:XX:XX:XX:XX:XX X.X.X.XXXXXXXXXX New Devices ATS100-XXXX XX:XX:XX:XX:XX:XX 16

17 7 Press "Connect" 8 Press "OK" then it can be connected to ATS100 with beep. 07:00 07:00 X.X.X.XXXXXXXXXX X.X.X.XXXXXXXXXX ATS100-XXXX XX:XX:XX:XX:XX:XX Connect ATS100-XXXX XX:XX:XX:XX:XX:XX Delete Bluetooth pairing request Confirm passkey is XXXXXX to pair with ATS100-XXXX. CANCLE OK 17

18 Bluetooth disconnection with Android 1 Select ( ) in the right hand side arrow. 2 Select "Disconnect" with beep 07:00 07:00 ATS100-XXXX XX:XX:XX:XX:XX:XX X.X.X.XXXXXXXXXX ATS100-XXXX XX:XX:XX:XX:XX:XX X.X.X.XXXXXXXXXX Disconnect Delete Delete Android Device with Bluetooth Connection 1 Select ( ) in the right hand side arrow. 07:00 2 Select "Delete" to take out the device in the connection list 07:00 ATS100-XXXX XX:XX:XX:XX:XX:XX X.X.X.XXXXXXXXXX ATS100-XXXX XX:XX:XX:XX:XX:XX X.X.X.XXXXXXXXXX Disconnect Delete Important List of devices in Bluetooth record can't be deleted. 18

19 USB Connection with Android Phone Ensure the ATID Application for Android is Installed the mobile. Installation SDK : Important Ensure the ATS100 USB Mode with VCP. (See setting USB on page14) Notice Before trying to connect to the mobile, it must be enabled from Android Ver. 4.2 (Jelly Bean). To be recommended ver.6.0(mashmallow) for activation. 1 Put USB Cable to Phone USB Port. (See Mounting QUAD LOCK & Smart Phone on page 7-8) 2 Press the application. 19

20 3 Select "YES" (Ensure the Bluetooth mode when pair to device) 4 Select "New Device" 06:59 06:59 X.X.X.XXXXXXXXXX X.X.X.XXXXXXXXXX Application is requesting permission to turn on Bluetooth Allow? NO YES 5 Select "USB" 6 Select "Scan Device" 06:59 06:59 Regist Device Regist Device Bluetooth USB Bluetooth USB Paired Devices New Devices New Devices Enable connect an usb device automatically 20

21 7 Press the correct device on the New Devices list. 8 Press ( ) 06:59 07:00 Regist Device New Devices Bluetooth ATXXUSBSerial Unknown USB ATXXUSBSerial Unknown X.X.X.XXXXXXXXXX Enable connect an usb device automatically 9 Select "Connect" 10 Press "OK" then It can be connect ATS100 with beep. 07:00 07:00 X.X.X.XXXXXXXXXX X.X.X.XXXXXXXXXX ATXXUSBSerial Unknown Connect Enable Auto Connect Delete ATXXUSBSerial Unknown Allow the app to access the USB device? Use by default for this USB device CANCLE OK 21

22 USB disconnection with Android 1 Select ( ) in the right hand side arrow. 2 Select "Disconnect" with beep 07:00 07:00 X.X.X.XXXXXXXXXX X.X.X.XXXXXXXXXX ATS100 ATXXXXXXXXXXX ATS100 ATXXXXXXXXXXX Disconnect Enable Auto Connect Delete Delete Android Device with USB Connection 1 Select ( ) in the right hand side arrow. 2 Select "Delete" row to be taken to the device connection. 07:00 07:00 ATS100 ATXXXXXXXXXXX X.X.X.XXXXXXXXXX X.X.X.XXXXXXXXXX ATS100 ATXXXXXXXXXXX Disconnect Enable Auto Connect Delete 22

23 Scanning RFID Tag : Android Phone Ensure connection to Android device via Bluetooth or USB. 1 Select guided arrow area. If you select You might have accidentally deleted Device in the list 2 Select "RFID". 07:00 07:00 Inventory ATS100 ATXXXXXXXXXXX X.X.X.XXXXXXXXXX RFID Barcode Key Tag/Total Count Select start or pull trigger. 4 Select "Stop" or release Trigger it will stop 07:00 scanning Tag. Inventory RFID Barcode Key Tag/Total Count 0 0 Trigger 23

24 5 View list of scanned data. Inventory 07:01 RFID Barcode Key XXXXXXXXXXXXXXXXXXXXXXXXXXXX 6 XXXX XXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXX Tag/Total Count

25 Scanning Barcode : Android Phone Ensure connection to Android device via Bluetooth or USB. 1 Select guided arrow area. If you select You might have accidentally deleted Device in the list 2 Select "RFID". 07:00 07:00 Inventory ATS100 ATXXXXXXXXXXX X.X.X.XXXXXXXXXX RFID Barcode Key Tag/Total Count Select start or pull trigger. Inventory 07:00 4 When the Barcode is within the scan range, the Barcode can be read. RFID Barcode Key Tag/Total Count 0 0 Trigger 25

26 5 View list of scanned data. Inventory 07:01 RFID Barcode Key UPCA XXXXXXXXXXXX A 1 Tag/Total Count

27 Bluetooth Connection with iphone Ensure the ATID Application for iphone is installed in the mobile. Installation SDK : Important Ensure the ATS100 Bluetooth Mode with BLE. (See setting Bluetooth on page13) 1 Go to settings and Tap on the Bluetooth to be taken Bluetooth mode. 2 Press the application. 오후 1:34 98% Settings Bluetooth Bluetooth Location accuracy and nearby services are improved when Bluetooth is turned on Notice The application will be applicable higher version of ios

28 3 Press "New Device" to complete Bluetooth Connection 4 Awaiting list on the device 오후 1:35 98% 오후 1:35 98% Demo Back Regist Device Paired Devices XXXXXX.X New Devices 5 Press the right Device to be Connected with beep 오후 1:35 98% Back Regist Device Paired Devices New Devices ATS100-XXXX 28

29 Bluetooth disconnection with iphone 1 Select ( ) in the right hand side arrow. 2 When the buzzer sounds and the color of the changes to blue, the connection is released. 오후 1:35 98% 오후 1:36 98% Demo Demo XXXXXX.X XXXXXX.X ATS100-XXXX ATS100-XXXX Delete iphone Device with Bluetooth Connection 1 Select ( ) in the right hand side arrow. 2 "OK". 오후 1:35 Demo 98% 오후 1:36 98% Demo XXXXXX.X XXXXXX.X ATS100-XXXX Delete Do you want to delete the selected conntection? Cancel OK 29

30 Scanning RFID Tag : ios Ensure Connection to ios Device via Bluetooth. 1 " Inventory". 2 Select "Start" or pull Trigger. 오후 1:36 98% Inventory 오후 1:36 98% Inventory Inventory Barcode Inventory Barcode Tag/Total Count 0/0 Tag/Total Count 0/0 3 Select "Stop" or release Trigger it will stop scanning Tag. 4 View list of scanned data 오후 1:36 98% Inventory Inventory Barcode XXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXX 6 XXXXXXXXXXXXXXXXXXXXXXXXXXX 17 XXXXXXXXXXXXXXXXXXXXXXXXXXXX 22 XXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXX 21 XXXXXXXXXXXXXXXXXXXXXXXXXXXX 13 Trigger XXXXXXXXXXXXXXXXXXXXXXXXXXXX 23 Tag/Total Count 24/296 30

31 Scanning barcode : ios Ensure Connection to ios Device via Bluetooth. 1 " Barcode". 2 Select "Start" or pull Trigger. 오후 1:37 98% Inventory 오후 1:37 98% Inventory Inventory Barcode Inventory Barcode Tag/Total Count 0 Total Count 0 3 When the Barcode is within the scan range, the Barcode can be read. 4 View list of scanned data. 오후 1:37 98% Inventory Inventory Barcode UPC -A XXXXXXXXXXXX Code 39 CODE 39 UCC/ EAN -128 XXXXXXXXXXXXXXXX UPC -E XXXXXXXX Trigger Total Count 4 31

32 Bluetooth Connection with Windows Ensure the ATID Demo Program for Windows is installed in the PC. Installation SDK : Important Ensure the ATS100 Bluetooth mode with SPP. (See setting Bluetooth on page13) Notice Ensure ".NET Framework 3.5" installed in the PC. Windows 7 Start > Devices and Printers > Add device The wireless devices will appear, accompany by relevant device information. Select ATS100-XXXX and Next. Following procedure can be paired device. ( For Windows10 go to next page.) Properties > Service : Remember Port name COM5 Check 32

33 Windows 10 Start > Devices and Printers The wireless devices will appear, accompany by relevant device information. Select ATS100-XXXX and select Next. Following procedure can be paired device. Properties > Service : Remember Port name COM5 Check 1 Launch Demo Program. 2 Select ATS100 in product list 33

34 Important Ensure Port name, communication type, paring status and installation driver. 3 The selected Device will be the same Port name by properties. 4 "Connect" then the Device will be Connected with beep 34

35 Bluetooth disconnection with Windows "Disconnect" then the Device will be disconnected with beep 35

36 USB Connection with Windows Ensure the ATID Demo Program for Windows is installed in the PC. Installation SDK : Important Ensure the ATS100 USB mode with VCP. (See setting USB communication on page14) Notice Ensure ".NET Framework 3.5" installed in the PC. 1 Input USB connector to ATS100 2 Input USB connector to PC. 36

37 3 The selected device will be the same Port name by properties Check 4 Launch Demo Program. 5 Select ATS100 in product list 37

38 Important Ensure Port name, Communication Type, paring status and installation driver. Ensure USB driver for Windows is installed in the PC. Installation : 6 The selected Device will be the same Port name by properties. 7 "Connect" then the Device will be Connected with beep 38

39 USB disconnection with Windows "Disconnect" then the device will be disconnected with beep Scanning RFID Tag : Windows Ensure Connection to Windows via Bluetooth or USB. 1 Ensure Operation mode is RFID. Check 39

40 2 If you don't want to detect Tag in continuous Mode, please deselect "Continuous". Check 3 Select "start" or pull trigger. 40

41 4 Select stop or release Trigger will be stop scanning the Tag. Trigger 5 View list of scanned data. 41

42 Scanning Barcode : Windows Ensure connection to Windows via Bluetooth or USB. 1 Select guided arrow area in Operation Mode. 2 Select "Start" or pull Trigger. 42

43 3 The Barcode will be scanned in range. Trigger 4 View list of scanned data 43

44 ATS100 Specifications Performance Characteristics Processor Physical Characteristics Dimensions (W x L x H) Weight Power Standard I/O Port Audio Data Capture Barcode RFID (UHF) Frequency Reading range RF output Protocol Wireless Communication Bluetooth User Environment ARM7 Core 76.1 x x mm (without QUAD LOCK ) 420g (With Battery) Input DC 5V 2A USB type-c, VCP, HID Buzzer 1D or 2D Imager Barcode Scanner MHz (US) / MHz (EU) MHz (Japan 1W LBT) MHz (Japan 0.25W LBT) 0M ~ 5M (According to Tag & Environment) 1W (MAX) Operating temperature -20 C to 60 C Storage temperature Humidity Drop Specification Dust & Water Proof Additional Features Notification CRADLE (OPTION) Standard Interface GUN HANDLE (OPTION) Gun Handle Battery MOUNT (OPTION) Mount Type GEN2, ISO / IEC C Bluetooth V4.1 Class 1 (HID, SPP, BLE) -30 C to 70 C 95% non - condensing 1.5M Drop to steel plate IP65 LED, Buzzer, Vibrator Charge Only (Option), USB Type-C Lithium-Ion 3.7V 5,200mAH (Rechargeable) QUAD LOCK Mount Type Mount Mechanism 44

45 Details about ATS100 For further information ATS100 please visit Download SDK For SDK installation, please visit Warranty and Product service s products have warranty against defects in workmanship and materials for a period of 1year shall not be responsible for any damage to or loss of any Software programmes, data or removable data storage media, or the restoration or reinstallation of any Software programmes or data. Certificate This device complies with KC, FCC, CE and TELEC rules. However, changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment ATID CO.,Ltd. Address : Byuksan Digital Valley-II #1211, 184 Gasan Digital 2-Ro, Gumcheon-Gu, Seoul, KOREA (Zip code: 08501) Tel : Fax : Website : atid@atid1.com The contents of the User's Manual are subject to change without notice for the purpose of changing specifications or improving the product. 45

46 Memo 46

47 Product Warranty - This product is manufactured through strict quality control and inspection. - If a malfunction occurs during normal use, you can get it repaired free of charge during the warranty period through your retailer or distributor. - Even if the warranty period expires or the warranty period is valid, the repair cost will be charged for the customer's fault (disassembly, modification, dropping, shock, damage, unreasonable operation, etc.). - In the event of a malfunction due to natural disasters (fire, salt damage, flood, etc.), repair costs will be charged. - If the consumable parts have reached the end of their useful life, the repair costs will be charged. - Please present warranty when requesting repair. - Warranty will not be reissued, please keep it carefully. - This warranty is only valid of purchase country. Perforated line Manufacturer ATID CO.,Ltd. Product type Bluetooth reader Warranty Period 1 Year Country of manufacture Korea Model name ATS100 Warranty Exclusions Purchasing office * Purchase year * Accessories other than body (But, the warranty period of the battery is 6 months based on the shipment date.) Customer Name * Customer phone number * Customer address * Please fill in the part of * before submission. Memo 47

48 Head Office: Address : Byuksan Digital Valley-II #1211, 184 Gasan Digital 2-Ro, Gumcheon-Gu, Seoul, KOREA (Zip code: 08501) Tel : Fax : Website : atid@atid1.com Overseas Sales: English : Japanese :