SV100G2 BIOS. User Manual

Transcription

1 SV100G2 BIOS User Manual Version 1.1 August Copyright 2016 Wiwynn. All rights reserved.

2 Copyright Copyright 2016 by Wiwynn Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Wiwynn Corporation. Disclaimer The information in this guide is subject to change without notice. Wiwynn Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Wiwynn Corporation software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Wiwynn Corporation, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. 2 Wiwynn SV100G2 BIOS User Manual

3 Revision History Date Version Changes 2016/07/ First release 2016/08/ Changed all screens. 2. Modified changes based on Setup Menu v0.09 in pages 7, 8, 9, 17 to 22 (added section 3.2), 26, 27, 29, 30 (added section 3.5), 32, 55, 62, 63, 64, 69, 70 and 71. Wiwynn SV100G2 BIOS User Manual 3

4 Contents Preface... 6 Introduction... 6 About this Manual BIOS Setup Entering BIOS Setup BIOS Hotkeys Menu Bar Navigation Keys Main Advanced Intel(R) Ethernet Connection X552 to 10 GBE SFP LSI SAS3 MPT Controller SAS Trusted Computing Serial Port Console Redirection Network Stack Configuration CSM Configuration USB Configuration Wiwynn Options IntelRCSetup Processor Configuration Advanced Power Management Configuration Memory Configuration IIO Configuration PCH Configuration Server ME Configuration Runtime Error Logging Server Mgmt System Event Log BMC Self Test Log BMC Network Configuration Security Wiwynn SV100G2 BIOS User Manual

5 7. Boot Save & Reset POST Code Table PEI Phase DXE Phase BIOS Recovery and Flash Update BIOS Recovery BIOS Flash Update Wiwynn SV100G2 BIOS User Manual 5

6 Preface Basic Input/Output System (also known as BIOS) is a firmware program stored on a chip in the system mainboard. Introduction BIOS Setup is a text-based utility that allows the user to configure the system and view current settings and environment information for the platform devices. The Setup utility controls the platform s built-in devices, the Boot Manager and Error Manager. About this Manual This manual contains information about the system BIOS and discusses how to configure the system by changing the settings of the BIOS parameters. Chapter 1 contains information regarding the BIOS setup, hotkeys, menu bar and navigation keys. Chapters 2 to 8 contain detailed description of the BIOS menus, submenus and functions. Chapter 9 lists the POST Code Table. Chapter 10 shows the BIOS recovery and update methods. 6 Wiwynn SV100G2 BIOS User Manual

7 1. BIOS Setup 1.1 Entering BIOS Setup To enter BIOS Setup, press the <Del> key during the Power-On-Self-Test (POST) to enter the BIOS Setup menu, otherwise, POST will continue with its test routines. Note that the BIOS Setup options may vary depending on your hardware configuration. 1.2 BIOS Hotkeys The following hotkeys work during POST: Key Del Esc F1 F2 F3 F4 F7 Function Enter BIOS setup utility Exit General Help Previous Values Optimized Defaults Save & Reset Enter Boot Menu Wiwynn SV100G2 BIOS User Manual 7

8 1.3 Menu Bar The tabs on the BIOS Menu bar on the top of the screen are: Main: Shows the BIOS, processor and system memory information. You can set the System Time and System Date here. Advanced: Sets the Advanced settings for Power, Memory, USB, and Super IO. IntelRCSetup: Sets the processor, thermal, USB, Network, South and North Bridge chipsets configurations, and system event log. Server Mgmt: Configures server management features. Security: Sets the system security features. Boot: Sets the boot configuration, quiet boot and boot device priority. Save & Exit: Allows the user to save or discard the configuration changes made on other Setup screens. Use < Enter > key or to select a field on the menu bar. 8 Wiwynn SV100G2 BIOS User Manual

9 1.4 Navigation Keys Use the following navigation keys to set the BIOS parameters: Key Function >< Select screen <Enter> Select item Select +/- Change option F1 F2 F3 F4 <Esc> General Help Previous Values Optimized Defaults Save & Reset Exit NOTES: Setup options may vary depending on your hardware configuration. Grayed-out fields are not user-configurable. In the descriptive table following each of the menu screenshots, settings in boldface are the default and suggested settings. Wiwynn SV100G2 BIOS User Manual 9

10 2. Main After entering the Setup Menu, you will see the Main menu screen. The Main menu displays the BIOS, memory and chipset information. You can set the system date and time. 10 Wiwynn SV100G2 BIOS User Manual

11 Parameter Description Option System Date System Time Set the date. Use Tab to switch between the date elements. Format is Day MM/DD/YYYY, Set the time. Use Tab to switch between the time elements. Hours are in 24-hour format. Format is HH:MM:SS Wiwynn SV100G2 BIOS User Manual 11

12 3. Advanced Setting the wrong values in the Advanced menu may cause the system to malfunction. Advanced screen provides an access point to configure several groups of options. On this screen, the user can select the option group to be configured. Configuration actions are performed on the selected screen, and not directly on the Advanced screen. Parameter Intel(R) Ethernet Connection X552 to 10 GBE SFP+ Trusted Computing Serial Port Console Redirecting CSM Configuration USB Configuration Wiwynn Options Description Configure 10 Gigabit Ethernet device parameters. Trusted Computing Settings Serial Port Console Redirection Enable or disable CSM configuration, Option ROM execution settings, etc. USB configuration parameters Wiwynn features options 12 Wiwynn SV100G2 BIOS User Manual

13 3.1 Intel(R) Ethernet Connection X552 to 10 GBE SFP+ Use this submenu to configure the 10 Gb Ethernet device parameters. The parameters of this configuration are dependent on Intel driver Intel(R) Ethernet Connection X552 to 10 GBE SFP+F8:0F:41:03:AE:FE Wiwynn SV100G2 BIOS User Manual 13

14 NOTE: SFP+ Wake on LAN (WoL) currently is Non-POR in Broadwell-DE SoC. 14 Wiwynn SV100G2 BIOS User Manual

15 3.1.2 Intel(R) Ethernet Connection X552 to 10 GBE SFP+F8:0F:41:03:AE:FF Wiwynn SV100G2 BIOS User Manual 15

16 NOTE: SFP+ Wake on LAN (WoL) currently is Non-POR in Broadwell-DE SoC. 16 Wiwynn SV100G2 BIOS User Manual

17 3.2 LSI SAS3 MPT Controller SAS3224 Use this submenu to enter Avago Technologies (LSI) SAS3 MPT Controller HII Configuration Application. Select to continue with HII Configuration. Wiwynn SV100G2 BIOS User Manual 17

18 Select to manage controller properties View Controller Properties 18 Wiwynn SV100G2 BIOS User Manual

19 Wiwynn SV100G2 BIOS User Manual 19

20 3.2.2 Change Controller Properties Parameter Description Option Legacy BIOS Display the current status of Legacy BIOS. Select and Apply Changes to modify. Enabled, Disabled 20 Wiwynn SV100G2 BIOS User Manual

21 3.2.3 Advanced Controller Properties Wiwynn SV100G2 BIOS User Manual 21

22 Parameter Description Option New Port Configuration Number of Phys per Port Auto: Controller automatically configures the ports. Manual: User maps the controller phys to port numbers. Specify how many phys will be configured per port. The phys will be sequentially assigned to ascending port numbers, starting with port 0. Manual, Auto 4, 1, 2, 8 22 Wiwynn SV100G2 BIOS User Manual

23 3.3 Trusted Computing Wiwynn SV100G2 BIOS User Manual 23

24 Parameter Description Option Configuration Security Device Support Current Status Information TPM Enabled Status: TPM Active Status: TPM Owner Status: Enable or disable BIOS support for security device. If Disabled, the OS will not show the security device. TCG EFI protocol and INT1A interface will not be available. If Enabled, system will schedule an operation for the security device. Display the current status of the security device. Provide the current capability state of the security device. Provide the current capability state of the security device. Provide current ownership state, i.e., Owned or Unowned. Enable, Disable Enabled Disabled Activated Deactivated Owned Unowned 24 Wiwynn SV100G2 BIOS User Manual

25 3.4 Serial Port Console Redirection To manage your host remotely from a serial console, you can redirect the console to a serial port. Use this option to enable or disable the Console Redirection function. Wiwynn SV100G2 BIOS User Manual 25

26 Parameter Description Option Console Redirection Settings The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings. Console Redirection Enable or disable Console Redirection Enabled, Disabled Console Redirection Settings The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings COM0 Console Redirection Settings 26 Wiwynn SV100G2 BIOS User Manual

27 Parameter Description Option Terminal Type Bits per second Character formatting used for console redirection. This setting must match the remote terminal application. ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes. Select the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds. VT-UTF8, ANSI, VT100, VT , 9600, 19200, 38400, Data Bits Data bits. 8, 7 Parity Stop Bits A parity bit can be sent with the data bits to detect transmission errors. Even: Parity bit is 0 if the no. of 1's in the data bits is even. Odd: Parity bit is 0 if no. of 1's in the data bits is odd. Mark: Parity bit is always 1. Space: Parity bit is always 0. Note that Mark and Space Parity do not allow for error detection. They can be used as an additional data bit. Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. None, Even, Odd, Mark, Space 1, 2 Wiwynn SV100G2 BIOS User Manual 27

28 Parameter Description Option Flow Control VT-UTF8 Combo Key Support Recorder Mode Flow control prevents data loss from buffer overflow. If the receiving buffers are full during data sending, a 'stop' signal can be sent to stop the data flow. Once the buffers are empty, a 'start' signal can be sent to restart the flow. Hardware flow control uses two wires to send the start/stop signals. Enable VT-UTF8 Combination Key Support for ANSI/VT100 terminals. If this mode is enabled, only text will be sent. This is to capture Terminal data. None, Hardware RTS/CTS Enabled, Disabled Disabled, Enabled Putty KeyPad Select FunctionKey and KeyPad on Putty. VT100, LINUX, XTERMR6, SCO, ESCN, VT400 Redirection After BIOS POST The Settings specify if Boot Loader is selected then Legacy console redirection is disabled before booting to Legacy OS. Default value is Always Enable which means Legacy console Redirection is enabled for Legacy OS. Always Enable BootLoader 28 Wiwynn SV100G2 BIOS User Manual

29 Console Redirection Settings Parameter Description Option Out-of-Band Microsoft Windows Emergency Management Services (EMS) allows for remote management of a Windows Server OS through a serial port. COM1, COM0 Wiwynn SV100G2 BIOS User Manual 29

30 3.5 Network Stack Configuration Parameter Description Option Network Stack Enable or disable UEFI Network Stack. Enabled, Disabled Ipv4 PXE Support Enable or disable ipv4 PXE Boot Support. If disabled, ipv4 boot option will not be created. Enabled, Disabled Ipv6 PXE Support Enable or disable ipv6 PXE Boot Support. If disabled, ipv6 boot option will not be created. Enabled, Disabled 30 Wiwynn SV100G2 BIOS User Manual

31 3.6 CSM Configuration This function enables or disables the Compatibility Support Module Configuration (CSM). Wiwynn SV100G2 BIOS User Manual 31

32 If CSM Support is enabled, you will see the following parameters: Parameter Description Option CSM Support Enable or disable CSM Support. Enabled, Disabled Boot option filter Controls Legacy/UEFI ROMs priority. UEFI only, Legacy only Network Controls the execution of UEFI and Legacy PXE OpROM. Auto, UEFI, Do not launch, Legacy Storage Controls the execution of UEFI and Legacy Storage OpROM. Auto, UEFI, Do not launch, Legacy Video Controls the execution of UEFI and Legacy Video OpROM. Legacy, UEFI Other PCI devices Determines OpROM execution policy for devices other than Network, Storage or Video Auto, UEFI, Do not launch, Legacy 32 Wiwynn SV100G2 BIOS User Manual

33 3.7 USB Configuration Parameter Description Option Legacy USB Support Device reset time-out Select Enabled to enable legacy USB support. Auto disables legacy support if no USB devices are connected. Disabled keeps USB devices available only for EFI applications. USB mass storage device Start Unit command time-out. Enabled, Disabled Auto 20 sec, 10 sec, 30 sec, 40 sec Wiwynn SV100G2 BIOS User Manual 33

34 3.8 Wiwynn Options Parameter Description Option Endless Boot Console Redirection Switch Enable infinity boot loop when the system did not find any bootable device. Console redirection switch. Enabled, Disabled Auto, Local, SOL Debug Mode For BIOS engineer debugging. Enabled, Disabled 34 Wiwynn SV100G2 BIOS User Manual

35 4. IntelRCSetup Parameter Processor Configuration Advanced Power Management Configuration Memory Configuration IIO Configuration PCH Configuration Server ME Configuration Runtime Error Logging Description Display and provide the option to change the Processor settings. Display and provide the option to change the Power Management settings. Display and provide the option to change the Memory settings. Display and provide the option to change the IIO settings. Display and provide the option to change the PCH settings. Configure Server ME Technology Parameters Press <Enter> to view or change the runtime error log configuration. Wiwynn SV100G2 BIOS User Manual 35

36 4.1 Processor Configuration This submenu displays and provides the option to change the Processor settings. Parameter Description Option Hyper- Threading (ALL) Execute Disable Bit Enable Intel TXT Support Enable Hyper-threading (software method) to enable or disable logical processor threads. When disabled, forces the XD feature flag to always return 0. Enable Intel Trusted Execution Technology Configuration. Disable the "EV DFX Features" when TXT is enabled. Enable, Disable Enable, Disable Disable, Enable VMX Enable the Vanderpool Technology to take effect after reboot. Enable, Disable Enable SMX Enable or disable Safer Mode Extensions. Enable, Disable 36 Wiwynn SV100G2 BIOS User Manual

37 4.2 Advanced Power Management Configuration Wiwynn SV100G2 BIOS User Manual 37

38 Parameter Description Option CPU PM Tuning EIST (P-States) CPU P State Control CPU C State Control CPU Advanced PM Turning If Auto is selected, all bits in MSR 1FCh keeping value as PO. When enabled, OS sets CPU frequency according to the load. When disabled, CPU frequency is set at max non-turbo. Control the CPU frequency. Control the CPU idle states. Additional CPU Power Management settings. Auto, Manual Enabled, Disabled 38 Wiwynn SV100G2 BIOS User Manual

39 4.2.1 CPU P State Control Parameter Description Option Turbo Mode Turbo mode allows a CPU logical processor to execute a higher frequency when enough power is available but not exceeding CPU defined limits. Enable, Disable Wiwynn SV100G2 BIOS User Manual 39

40 4.2.2 CPU C State Control 40 Wiwynn SV100G2 BIOS User Manual

41 Parameter Description Option C2C3TT CPU C State Package C State limit CPU C3 report CPU C6 report Enhanced Halt State (C1E) OS ACPI Cx Default is 0, means [AUTO]. C2 to C3 Transition Timer, PPDN_INIT = 1:10:1:74 Bit[110] Enable the Enhanced Cx state of the CPU, takes effect after reboot. Package C State limit. Enable or disable CPU C3 (ACPI C2) report to OS. Recommended is Disable. Enable or disable CPU C6 (ACPI C2) report to OS Recommended is Enable. Enable the Enhanced C1E state of the CPU, takes effect after reboot. Report CC3/CC6 to OS ACPI C2 or ACPI C3. 0 to 256 Enable, Disable C6 (Retention) state, C0, C1 state, C2 state, C6 (non Retention) state, Disable, Enable Enable, Disable Enable, Disable ACPI C2, ACPI C3 Wiwynn SV100G2 BIOS User Manual 41

42 4.2.3 CPU Advanced PM Tuning Parameter Energy Perf BIAS Description Provide hint to CPU for better performance or power savings. 42 Wiwynn SV100G2 BIOS User Manual

43 Parameter Description Option Energy Performance Tuning Energy Performance BIAS setting Select BIOS or Operating System to choose the energy performance bias tuning. Set Energy Performance BIAS, which overrides OS setting Enable, Disable Balanced Performance, Performance, Balanced Power, Power Wiwynn SV100G2 BIOS User Manual 43

44 4.3 Memory Configuration 44 Wiwynn SV100G2 BIOS User Manual

45 Parameter Description Option Memory Frequency Maximum Memory Frequency Selections in MHz. Auto, 1600, 1867, 2133, 2400 ECC Support Enable or disable DDR ECC Support. Auto, Enable, Disable Memory Topology Display the memory topology with DIMM population information. Each socket has 2 Nodes/iMC's (numbered from 0-7). Each node supports up to 2 channels (0&1) and 3 DIMM's per channel (0,1&2) on EP platforms. Memory Set the memory thermal settings. Thermal Memory RAS Configuration Display and change the Memory RAS Settings. Wiwynn SV100G2 BIOS User Manual 45

46 4.3.1 Memory Topology 46 Wiwynn SV100G2 BIOS User Manual

47 4.3.2 Memory Thermal Parameter Description Option Set Throttling Mode Configure Thermal Throttling Mode. Select Disblaed, OLTT or CLTT mode. CLTT, Disabled, OLTT Wiwynn SV100G2 BIOS User Manual 47

48 4.3.3 Memory RAS Configuration Parameter Description Option Correctable Error Correctable Error Threshold 4, 1, 10, 1000 Threshold (1/4/10/1000) used for sparing, tagging, and leaky bucket Patrol Scrub Enable or disable Patrol Scrub Enable, Disable Demand Scrub Enable or disable Demand Scrub Enable, Disable 48 Wiwynn SV100G2 BIOS User Manual

49 4.4 IIO Configuration Parameter Intel VT for Directed I/O (VT-d) Description Press <Enter> to bring up the Intel VT for Directed I/O (VT-d) Configuration menu. Wiwynn SV100G2 BIOS User Manual 49

50 Parameter Description Option Intel VT for Directed I/O (VT-d) Interrupt Remapping Coherency Support (Non-Isoch) Coherency Support (Isoch) Enable or disable Intel Virtualization Technology for Directed I/O (VT-d) by reporting the I/O device assignment to VMM through DMAR ACPI Tables. Enable or disable VT_D Interrupt Remapping Support. Enable or disable Non-Isoch VT_D Engine Coherency support. Enable or disable Isoch VT_D Engine Coherency support. Enable, Disable Enable, Disable Enable, Disable Enable, Disable 50 Wiwynn SV100G2 BIOS User Manual

51 4.5 PCH Configuration Parameter PCH Devices PCI Express Configuration PCH SATA Configuration USB Configuration Description Enable or disable Intel(R) IO Controller Hub devices. Press <Enter> to bring up the PCI Express Configuration menu. SATA devices and settings USB Configuration Settings Wiwynn SV100G2 BIOS User Manual 51

52 4.5.1 PCH Devices Parameter Description Option PCH state after G3 Select S0/S5 for ACPI state after a G3. Options are S0, S5 and Last State S5 (sync with BMC), S0, Last State 52 Wiwynn SV100G2 BIOS User Manual

53 4.5.2 PCH Express Configuration Parameter Description Option PCI-E ASPM Support (Global) Enable or disable ASPM support for all downstream devices. L1 Only, Disable Wiwynn SV100G2 BIOS User Manual 53

54 4.5.3 PCH SATA Configuration 54 Wiwynn SV100G2 BIOS User Manual

55 Parameter Description Option SATA Controller Enable or disable SATA controller. Enabled, Disabled Configure SATA as SATA Port # Configure SATA as AHCI. AHCI Port # Enable or disable SATA port. Enabled, Disabled Spin Up Device SATA Device Type If enabled for any of the ports, Staggered Spin Up will be performed and only the drives with this option enabled will spin up at boot. Otherwise all drives spin up at boot. Identify if the SATA port is connected to Solid State Drive or Hard Disk Drive. Disabled, Enabled Hard Disk Drive, Solid State Drive Wiwynn SV100G2 BIOS User Manual 55

56 4.5.4 USB Configuration Parameter Description Option xhci mode The xhci controller operation mode. Auto, Enabled, Disabled 56 Wiwynn SV100G2 BIOS User Manual

57 4.6 Server ME Configuration Parameter Description Option Altitude The altitude of the platform location above the see level, expressed in meters. The hex number is decoded as 2's complement signed integer. Provide the value if the altitude is unknown. 12C Wiwynn SV100G2 BIOS User Manual 57

58 4.7 Runtime Error Logging 58 Wiwynn SV100G2 BIOS User Manual

59 Parameter Description Option System Errors System Poison System Error enabling and logging setup option. Enable or disable Core, Uncore and IIO Poison. Enable, Disable, Auto Enable, Disable PCI/PCI Error Enabling Press <Enter> to view or change the PCH errors enabling options PCI/PCI Error Enabling Wiwynn SV100G2 BIOS User Manual 59

60 Parameter Description Option PCI-Ex Error Enable Corrected Error Enable Uncorrected Error Enable Enable or disable PCIe Correctable errors. Enable or disable PCIe Uncorrectable errors. Yes, No Enable, Disable, Enable, Disable, Fatal Error Enable Enable or disable PCIe Fatal errors. Enable, Enable SERR propagation Enable PERR propagation Enable PCI device to generate SERR#. Enable PCI device to generate PERR# Disable, Yes No Yes No 60 Wiwynn SV100G2 BIOS User Manual

61 5. Server Mgmt This menu allows the user to configure several server management features and also provided an access point to the screens for configuring Console Redirection, displaying system information and controlling the BMC LAN configuration. Wiwynn SV100G2 BIOS User Manual 61

62 Parameter Description Option BMC Support Enable or disable interfaces to communicate with BMC. Enabled, Disabled FRB-2 Timer Enable or disable FRB-2 timer (POST timer). Enabled, Disabled FRB-2 Timer timeout Enter a value between 3 to 6 minutes as the FRB-2 timer expiration value. 6 minutes, 3 minutes, 4 minutes, 5 minutes FRB-2 Timer Policy System Event Log Bmc self test log BMC Network Configuration Configure how the system should respond if Do Nothing, the FRB-2 Timer expires. Not available if Reset, FRB-2 Timer is disabled. Power Down, Power Cycle Press <Enter> to change the SEL event log configuration. Logs the report returned by the BMC self-test command. Configure BMC network parameters 62 Wiwynn SV100G2 BIOS User Manual

63 5.1 System Event Log Parameter Description Option When SEL is Full Log EFI Status Codes Choose an option in response to a full SEL. Enable or disable the logging of EFI Status Codes, log only error code or progress code, or both. Do Nothing, Erase Immediately Error code, Disabled, Both, Progress code Wiwynn SV100G2 BIOS User Manual 63

64 5.2 BMC Self Test Log Parameter Description Option Erase Log Erase Log options. Yes, on every reset, No Log EFI Status Codes Select the action to be taken when the log is full. Clear Log, Do not log anymore 64 Wiwynn SV100G2 BIOS User Manual

65 5.3 BMC Network Configuration Wiwynn SV100G2 BIOS User Manual 65

66 Parameter Description Option Configuration Address Source Select to configure LAN channel parameters statically or dynamically (by BIOS or BMC). Unspecified option will not modify any BMC network parameters during BIOS phase. Unspecified, Static, DynamicBmcDhcp, DynamicBmcNonDhcp 66 Wiwynn SV100G2 BIOS User Manual

67 6. Security The BIOS uses passwords to prevent unauthorized tampering with the server setup. To access this screen, select the Security option. Parameter Administrator Password Description Set the administrator password. Wiwynn SV100G2 BIOS User Manual 67

68 7. Boot 68 Wiwynn SV100G2 BIOS User Manual

69 Parameter Description Option Setup Prompt Timeout Number of seconds to wait for setup activation key (0xFFFF) means 1 to indefinite waiting. Bootup NumLock State Select the keyboard NumLock state upon bootup. On, Off New Boot Option Policy Control the placement of newly detected UEFI boot options. Default, Place First, Place Last Quiet Boot Enable or disable the Quiet Boot option. Disabled, Enabled Boot Option # Set the system boot order. UEFI USB Drive BBS Specify the Boot Device Priority sequence from available USB drives. Priorities UEFI NETWORK Specify the Boot Device Priority sequence from available network drives. Drive BBS Priorities UEFI Hard Disk Drive BBS Specify the Boot Device Priority sequence from available hard disk drives. Priorities Wiwynn SV100G2 BIOS User Manual 69

70 8. Save & Exit The Save & Exit screen allows the user to save or discard changes before resetting the system. It also allows the user to restore the BIOS Settings to the factory defaults or to save or restore them to a set of user-defined default values. 70 Wiwynn SV100G2 BIOS User Manual

71 Parameter Save Changes and Reset Discard Changes and Reset Save Changes Restore Defaults Description Reset the system after saving the changes. Reset the system without saving any changes. Save the changes done so far to any of the setup options. Restore/load default values for all the setup options. Save as User Defaults Restore User Default Save the changes done so far as User Defaults. Restore the User Defaults to all the setup options. Wiwynn SV100G2 BIOS User Manual 71

72 9. POST Code Table 9.1 PEI Phase A. Progress Codes Normal Code 0x10 0x11 0x15 0x19 0x2B 0x2C 0x2D 0x2E 0x2F 0x31 0x37 0x3B 0x4F 0x60 Description PEI Core is started Pre-memory CPU initialization is started Pre-memory North Bridge initialization is started Pre-memory South Bridge initialization is started Memory initialization. Serial Presence Detect (SPD) data reading Memory initialization. Memory presence detection Memory initialization. Programming memory timing information. Memory initialization. Configuring memory. Memory initialization Memory Installed Post-Memory North Bridge initialization is started Post-Memory South Bridge initialization is started DXE IPL is started DXE Core is started 72 Wiwynn SV100G2 BIOS User Manual

73 Recovery Code 0xF0 0xF1 0xF2 0xF3 0xF4 Description Recovery condition triggered by firmware (Auto recovery) Recovery condition triggered by user (Forced recovery) Recovery process started Recovery firmware image is found Recovery firmware image is loaded B. Error Codes Normal Code 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B Description Memory initialization error. Invalid memory type or incompatible memory speed. Memory initialization error. SPD reading has failed. Memory initialization error. Invalid memory size or memory modules do not match. Memory initialization error. No usable memory detected. Unspecified memory initialization error Memory not installed Invalid CPU type or Speed CPU mismatch CPU self-test failed or possible CPU cache error CPU micro-code is not found or micro-code update failed Internal CPU error Reset PPI is not available Wiwynn SV100G2 BIOS User Manual 73

74 Recovery Code 0xF8 0xF9 0xFA Description Recovery PPI is not available Recovery capsule is not found Invalid recovery capsule 9.2 DXE Phase A. Progress Codes Code 0x60 0x61 0x62 0x63 0x68 0x69 0x6A 0x70 0x71 0x72 0x78 0x79 0x90 0x91 0x92 0x93 0x94 0x95 Description DXE Core is started NVRAM initialization Installation of the South Bridge Runtime Services CPU DXE initialization is started PCI host bridge initialization North Bridge DXE initialization is started North Bridge DXE SMM initialization is started South Bridge DXE initialization is started South Bridge DXE SMM initialization is started South Bridge devices initialization ACPI module initialization CSM initialization Boot Device Selection (BDS) phase is started Driver connecting is started PCI Bus initialization is started PCI Bus Hot Plug Controller Initialization PCI Bus Enumeration PCI Bus Request Resources 74 Wiwynn SV100G2 BIOS User Manual

75 Code 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAB 0xAD 0xAE 0xAF 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 Description PCI Bus Assign Resources Console Output devices connect Console input devices connect Super IO Initialization USB initialization has started USB Reset USB Detect USB Enable IDE initialization has started IDE Reset IDE Detect IDE Enable SCSI initialization has started SCSI Reset SCSI Detect SCSI Enable Setup Verifying Password Start of Setup Setup Input Wait Ready To Boot event Legacy Boot event Exit Boot Services event Runtime Set Virtual Address MAP Begin Runtime Set Virtual Address MAP End Legacy Option ROM Initialization System Reset USB hot plug PCI bus hot plug Clean-up of NVRAM Configuration Reset (reset of NVRAM settings) Wiwynn SV100G2 BIOS User Manual 75

76 B. Error Codes Code 0xD0 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 0xDA 0xDB 0xDC Description CPU initialization error North Bridge initialization error South Bridge initialization error Some of the Architectural Protocols are not available PCI resource allocation error. Out of Resources No Space for Legacy Option ROM No Console Output Devices are found No Console Input Devices are found Invalid password Error loading Boot Option Boot Option is failed Flash update is failed Reset protocol is not available 76 Wiwynn SV100G2 BIOS User Manual

77 10. BIOS Recovery and Flash Update 10.1 BIOS Recovery Recovery is a BIOS function that allows the user to update or change the BIOS programmed into a flash part. For recovery to work, the BIOS must have the Boot Block section of the BIOS in a non-corrupted state. This means that BIOS will execute normally through the Boot Block phase of execution. If this is not possible, then the code used to perform a recovery may also be corrupted and therefore unreliable to properly execute. With the current implementation, the BIOS can detect if there is corrupt code in the flash part and it can automatically enter into a recovery mode. The recovery processes are listed below. 1 Once recovery mode has been invoked, the system will attempt to find the BIOS update file on the different media types that are enabled during porting. 2 Once the BIOS Update file has been found, the system will load that image into memory and boot from the new recovery image. 3 The boot process then automatically brings up a Setup page to start the recovery process. 4 If built with non-interactive mode, the BIOS will immediately start programming the recovery image into the flash part. If built with interactive mode, the Setup Screen will prompt the user with the option to program the recovery image with or without clearing the NVRAM area. 5 The default mode for the recovery module is set to interactive mode. Wiwynn SV100G2 BIOS User Manual 77

78 BIOS Recovery Instructions If any abnormal shutdown occurs during BIOS update and resulted in an incomplete update, the system will not power-on normally. Perform the following steps to recover the BIOS: 1 Copy HEITZ.ROM to the root directory of a USB key or hard disk drive with NTFS partition. 2 Reboot the system to perform auto recovery. 3 Enter the Setup menu Recovery page. 4 Set "Reset NVRAM" as "Enabled". 5 Set "Boot block update" as "Enabled". 6 Set "Main block update" as "Enabled". 7 Select Proceed with flash update then it will start flash update process. 8 Wait for 2-5 minutes to complete the flash update. 9 Reboot the system and observe if SUT boots normally. NOTE: If Boot Block crashes, this indicates that the system is unrecoverable. 78 Wiwynn SV100G2 BIOS User Manual

79 10.2 BIOS Flash Update For updating the BIOS, AMI provides independent BIOS vendor (IBV) utilities such as AFULNX for Linux-based OS and AFUWIN for Windows-based OS. Follow these steps to update the BIOS: 1 Use the flash command: AMIAFU filename.bin /X /B /P /K /N /ME For example: /afulnx_64 BWDE_E08.bin /X /B /P /K /N /ME (CentOS) 2 Reboot the system. Wiwynn SV100G2 BIOS User Manual 79