SIMATIC PC. Panel PC Industrial Lite Without Operating System. Preface, Table of Contents

Size: px

Start display at page:

Download "SIMATIC PC. Panel PC Industrial Lite Without Operating System. Preface, Table of Contents"

Rudolf Stephens
5 years ago
Views:

1 Preface, Table of Contents SIMATIC PC Panel PC Industrial Lite Without Operating System Installation Guide General Information 1 Installation of the Drivers Using MS Windows NT Installation of the Drivers Using MS Windows Millennium Edition 3 Installation of the Drivers Using MS Windows Appendix Edition 10/01

2 Safety Guidelines This manual contains notices which you should observe to ensure your own personal safety, as well as to protect the product and connected equipment. These notices are marked as follows according to the level of danger: Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Caution used with the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Caution used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. Notice indicates that unwanted events or status can occur if the relevant information is not observed. Qualified Personnel Correct Usage Note draws your attention to particularly important information on the product, handling the product, or to a particular part of the documentation. Equipment may be commissioned and operated only by qualified personnel. Qualified personnel within the meaning of the safety notices in this manual are persons who are authorized to commission, ground and identify equipment, systems and circuits in accordance with safety engeneering standards. Please note the following: Trademarks Impressum Warning The device may only be used for the application cases specified in the catalog and the technical description and may only be used in combination with third-party equipment and components recommended or approved by Siemens. Startup must not take place until it is established that the machine which is to accommodate this component is conforms with the guideline 98/37 EC. Appropriate transport, and appropriate storage, installation and assembly, as well as careful operation and maintenance, are required to ensure that the product operates perfectly and safely. The registered trademarks of the Siemens AG can be found in the preface. The remaining trademarks in this publication may be trademarks, whose use by third parties for their own purposes could violate the rights of the owner. Editor and Publisher: A&D PT1 D1 Copyright Siemens AG 2001 All rights reserved The transmission and reproduction of this documentation and the exploitation and communication of its contents are not allowed, unless expressly granted. Violators are liable for damages. All rights reserved, especially in the case of the granting of a patent or registration by GM. Siemens AG Bereich Automation & Drives Geschäftsgebiet SIMATIC HMI Postfach 4848, D Nürnberg Siemens Aktiengesellschaft Exclusion of liability We have checked the content of this publication for compliance with the described hard and software. However, discrepancies cannot be excluded, with the result that we assume no guarantee for total compliance. The information in this publication is checked regularly, and any necessary corrections are included in the following editions. We would be grateful for any suggestions for improvement. Siemens AG 2001 Technical data subject to change. Order number

3 1 Preface This manual This Installation Guide forms part of the documentation for the SIMATIC Panel PC Industrial Lite (subsequently referred to as Panel PC IL). Note This Software Installation Guide only applies to Panel PC Industrial Lite systems which are ordered from Siemens AG without an operating system. Notation Different font formats simplify orientation within the text: Motor on Output File Edit The text on the screen of the operating unit is displayed in typewriter font. Inputs and outputs on the screen of the operating unit are displayed in italic typewriter font. Menu items, dialog names, tab controls and buttons of the operating system and the application are displayed in italic font. In context with menu items the complete path is always described. Trademarks The following names are registered trademarks of the Siemens AG: SIMATIC SIMATIC HMI SIMATIC Panel PC HMI ProTool ProTool/Lite ProTool/Pro Panel PC IL Installation Guide Without Operating System i

4 Preface 10/01 ii Panel PC IL Installation Guide Without Operating System

5 Table of Contents 1 General Information Installation of the Drivers Using MS Windows NT Installation of the Graphics Driver (Intel Chipset Onboard Graphics) Installation of the Monitor Mouse for ELO Touchscreen Setting Up the Analog Devices AD188x WDM Audio (SoundMax) Setting Up the Intel 825xx Onboard LAN Adapter Installation of the Siemens Virtual Keyboard Installation of the Drivers Using MS Windows Millennium Edition Installation of the Graphics Driver (Intel Chipset Onboard Graphics) Installation of the Monitor Mouse for ELO Touchscreen Setting Up the Intel 825xx Onboard LAN Adapter Installation of the Drivers Using MS Windows Installation of the Monitor Mouse for ELO Touchscreen Installation of the Siemens Virtual Keyboard Appendix... a Panel PC IL Installation Guide Without Operating System iii

6 Table of Contents 10/01 iv Panel PC IL Installation Guide Without Operating System

7 1 General Information In the case of a Panel PC IL, drivers which are not available as part of the operating system supplied must be installed. The driver installation is described for the following operating systems: Microsoft Windows NT 4.0 Microsoft Windows ME Microsoft Windows 2000 The installation of the operating system is not described. Note The information applies to the operating system languages German and English. The installation described below was tested on a Panel PC IL with a D1215-A2 system board. The scope of delivery of the SIMATIC Panel PC IL 70 includes the "PC IL 70 Documentation & Drivers" CD. This CD contains the drivers for the following devices: INF Packet for Intel Chipsets Intel Chipset Onboard Graphics Analog Devices AD188x WDM Audio Intel 825xx Onboard LAN Adapter Monitor Mouse for ELO Touchscreen Siemens Virtual Keyboard Microsoft DirectX 8.0a Microsoft Internet Explorer 5.5 Panel PC IL Installation Guide Without Operating System 1 1

8 General Information 10/ Panel PC IL Installation Guide Without Operating System

9 2 Installation of the Drivers Using MS Windows NT 4.0 In order to use the "PC IL 70 Documentation & Drivers" CD supplied properly, it is advisable to install the current Internet Explorer version and the latest Service Pack from Windows NT. Both can be found on the "PC IL 70 Documentation & Drivers" CD in the following paths: \updates\sp\nt4 for the Service Pack 6a \updates\ie\5.5 for Internet Explorer 5.5 Notice Please note that it is essential to install the Service Pack before Internet Explorer installation of IE 5.5 is based on a 128-bit coding. Installation of the Service Packs is no longer possible afterwards. When these conditions have been fulfilled on the PC, the drivers can be installed. Note It is recommended to copy the "MS Windows NT 4.0" directory \i386 from the CD to the root directory c:\i386 of your system data directory. The directory \i386 then contains the files which are necessary for the installation of the drivers. Panel PC IL Installation Guide Without Operating System 2 1

10 Installation of the Drivers Using MS Windows NT / Installation of the Graphics Driver (Intel Chipset Onboard Graphics) 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the graphics board are located under menu item Intel Chipset Graphics for Windows NT Select the required drivers from the corresponding operating system and start the installation by clicking on the icon. 3. Restart the PC following successful installation. 2 2 Panel PC IL Installation Guide Without Operating System

11 10/01 Installation of the Drivers Using MS Windows NT Installation of the Monitor Mouse for ELO Touchscreen 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the ELO Touchscreen are located under the menu item ELO Monitor Mouse for Windows NT Start the installation by clicking on the icon. The files required for the installation are decompressed in c:\elont. 3. Change to the directory \elont in order to install the touchscreen software and execute the Setup. Notice During the installation, ensure that the serial interface COM 2 is defined as the interface for the ELO Touchscreen. Otherwise, the display will not be activated. Panel PC IL Installation Guide Without Operating System 2 3

Installation of the Drivers Using MS Windows NT 4.0 10/01 4. Restart the PC following successful installation. 5.

12 Installation of the Drivers Using MS Windows NT /01 4. Restart the PC following successful installation. 5. Calibrate the ELO Touchscreen immediately after the restart. Follow the instructions which appear on the screen. The ELO Touchscreen is now configured. 2 4 Panel PC IL Installation Guide Without Operating System

13 10/01 Installation of the Drivers Using MS Windows NT Setting Up the Analog Devices AD188x WDM Audio (SoundMax) 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the Analog Devices AD188x Audio are located under menu item Analog Devices AD188x Audio for Windows NT Start the installation by clicking on the icon. 3. Restart the PC following successful installation. Panel PC IL Installation Guide Without Operating System 2 5

Installation of the Drivers Using MS Windows NT 4.0 10/01 2.4 Setting Up the Intel 825xx Onboard LAN Adapter Example configuration 1.

You are requested to install the NT Networking. 3. Click on the Yes button. 4.

14 Installation of the Drivers Using MS Windows NT / Setting Up the Intel 825xx Onboard LAN Adapter Example configuration 1. Click on the Network neighborhood icon with the right mouse button on the desktop. 2. Select the menu item Properties. You are requested to install the NT Networking. 3. Click on the Yes button. 4. The system then requests information on how the computer is connected within the network. In most cases, it is necessary to select the Wired to the network check box. 5. Click on the Next button. 2 6 Panel PC IL Installation Guide Without Operating System

A selection window then opens containing a range of network adapter cards from various manufacturers. 7.

15 10/01 Installation of the Drivers Using MS Windows NT 4.0 You are then requested to select your network adapter. 6. Select the Select from list... button. A selection window then opens containing a range of network adapter cards from various manufacturers. 7. Do not select anything from the list but install the network adapter after clicking on the Have Disk... button. Panel PC IL Installation Guide Without Operating System 2 7

$The files necessary are located on the "PC IL 70 Documentation & Drivers" CD supplied in the following path: \driver\nic\intel\pro100\v5.$ 0 8. Enter the path specified and confirm it with OK. 9. Access the following configuration item by clicking on the Next button. 10.

0 8. Enter the path specified and confirm it with OK. 9. Access the following configuration item by clicking on the Next button. 10.

16 Installation of the Drivers Using MS Windows NT /01 You are then prompted to enter the path containing the network adapter driver. The files necessary are located on the "PC IL 70 Documentation & Drivers" CD supplied in the following path: \driver\nic\intel\pro100\v Enter the path specified and confirm it with OK. 9. Access the following configuration item by clicking on the Next button. 10. Select the TCP/IP Protocol check box and confirm the selection by clicking on Next. 2 8 Panel PC IL Installation Guide Without Operating System

10/01 Installation of the Drivers Using MS Windows NT 4.0 11. Select the services required. Select the default configuration.

$Note The necessary files are located in the directory c:\i386 if they were previously copied there (refer to the Note in Chapter 0). 12. Enter the path.$

17 10/01 Installation of the Drivers Using MS Windows NT Select the services required. Select the default configuration. To complete the installation, certain Windows NT components are required. It is necessary to insert the Windows installation CD in the CD-ROM drive again. Note The necessary files are located in the directory c:\i386 if they were previously copied there (refer to the Note in Chapter 0). 12. Enter the path. In the next step, you must select whether the DHCP service should be activated. If a DHCP server is operated in your network, you can define whether your Panel PC IL should be allocated an IP address from such a DHCP server. Panel PC IL Installation Guide Without Operating System 2 9

Installation of the Drivers Using MS Windows NT 4.0 10/01 Note If this is not the case, it is also possible to define an IP address later.

To conclude the process, confirm the windows which subsequently appear and follow the instructions. 15.

18 Installation of the Drivers Using MS Windows NT /01 Note If this is not the case, it is also possible to define an IP address later. 13. Select the Yes button in order to activate the DHCP service. 14. Define the network settings in the Specify an IP address field. To conclude the process, confirm the windows which subsequently appear and follow the instructions. 15. Restart the PC following successful installation. After restarting your PC, it is possible to access the Microsoft network Panel PC IL Installation Guide Without Operating System

19 10/01 Installation of the Drivers Using MS Windows NT Installation of the Siemens Virtual Keyboard 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the Siemens Virtual Keyboard are located under menu item Siemens Virtual Keyboard for Windows Me, NT 4.0 & Start the installation by clicking on the icon. 3. Restart the PC following successful installation. Panel PC IL Installation Guide Without Operating System 2 11

20 Installation of the Drivers Using MS Windows NT /01 4. After the PC has been restarted, conclude the installation by confirmation with the OK button. The Virtual Keyboard is then started. Your PC is now configured. You can now start with the installation of your applications Panel PC IL Installation Guide Without Operating System

21 3 Installation of the Drivers Using MS Windows Millennium Edition Note It is recommended to install the latest operating system Service Pack on the PC. Service Pack 2 is located on the "PC IL 70 Documentation & Drivers" CD. After completing the installation of MS Windows ME, you can start installing the specific drivers. Panel PC IL Installation Guide Without Operating System 3 1

22 Installation of the Drivers Using MS Windows Millennium Edition 10/ Installation of the Graphics Driver (Intel Chipset Onboard Graphics) 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the graphics board are located under menu item Intel Chipset Graphics for Windows Me. 2. Start the installation by clicking on the icon. The graphics card is automatically installed; the license agreement must be confirmed here. 3. Restart the PC following successful installation. 4. Set the screen resolution following the restart. Select Start Settings Control Panel Display. The following window is opened: 3 2 Panel PC IL Installation Guide Without Operating System

23 10/01 Installation of the Drivers Using MS Windows Millennium Edition Set the required resolution in Screen area: Resolution 12" display 800 x " display 1024 x 768 Panel PC IL Installation Guide Without Operating System 3 3

24 Installation of the Drivers Using MS Windows Millennium Edition 10/ Installation of the Monitor Mouse for ELO Touchscreen 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the ELO Monitor Mouse are located under the menu item ELO Monitor Mouse for Windows Me. 2. Start the installation by clicking on the icon. The files required for the installation are decompressed in c:\elontwin9x. Notice During the installation, ensure that the serial interface COM 2 is defined as the interface for the ELO Touchscreen. Otherwise, the display will not be activated. 3 4 Panel PC IL Installation Guide Without Operating System

25 10/01 Installation of the Drivers Using MS Windows Millennium Edition 3. Calibrate the ELO Touchscreen immediately after the restart. Follow the instructions which appear on the screen. Note It is not necessary to restart the PC. Panel PC IL Installation Guide Without Operating System 3 5

Installation of the Drivers Using MS Windows Millennium Edition 10/01 3.

26 Installation of the Drivers Using MS Windows Millennium Edition 10/ Setting Up the Intel 825xx Onboard LAN Adapter Although your network components were set up during installation of the operating system, it is still necessary to install the correct drivers for the network card. 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. 2. Open the Device Manager. The System Properties window contains the PCI Ethernet Controller device. 3. Select it and then click on the Properties button. The following window opens: 3 6 Panel PC IL Installation Guide Without Operating System

10/01 Installation of the Drivers Using MS Windows Millennium Edition 4. Select the Reinstall Driver button. 5. Confirm the subsequent window by clicking on Next. The driver is located and set up. 6.

27 10/01 Installation of the Drivers Using MS Windows Millennium Edition 4. Select the Reinstall Driver button. 5. Confirm the subsequent window by clicking on Next. The driver is located and set up. 6. Restart the PC. The network card is now configured. 7. Install the Siemens Virtual Keyboard. Proceed as in Point 3.1 described previously but select the menu item Siemens Virtual Keyboard and execute the installation. 8. Restart the PC following successful installation. The installation is concluded directly after the restart. Panel PC IL Installation Guide Without Operating System 3 7

28 Installation of the Drivers Using MS Windows Millennium Edition 10/ Panel PC IL Installation Guide Without Operating System

29 4 Installation of the Drivers Using MS Windows 2000 Note It is recommended to install the latest operating system Service Pack on the PC. Service Pack 2 is located on the "PC IL 70 Documentation & Drivers" CD. In order to install the necessary drivers in Windows 2000, select Start Settings Control Panel Display. The following window appears: The Plug & Play has recognized the device and entered the device in the Device Manager under the item Other devices but could not assign drivers to the device. These devices are identified by a question mark. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. Panel PC IL Installation Guide Without Operating System 4 1

Installation of the Drivers Using MS Windows 2000 10/01 Install the drivers: 1. Click on the relevant device with the right mouse button. 2. Select the menu item Properties.

30 Installation of the Drivers Using MS Windows /01 Install the drivers: 1. Click on the relevant device with the right mouse button. 2. Select the menu item Properties. The following window is opened: 3. Select the Reinstall Driver... button. The wizard then starts up. 4 2 Panel PC IL Installation Guide Without Operating System

10/01 Installation of the Drivers Using MS Windows 2000 4. Specify how the driver should be installed.

31 10/01 Installation of the Drivers Using MS Windows Specify how the driver should be installed. It is recommended to select the Search for a suitable driver for my device option. 5. Confirm the selection by clicking on Next. The following window requests a source where the drivers should be searched for. 6. Select the CD-ROM drives check box. Panel PC IL Installation Guide Without Operating System 4 3

32 Installation of the Drivers Using MS Windows /01 7. Confirm the selection by clicking on Next. The drivers are searched for on the CD ROM. Then follow the instructions on the screen. Install the drivers in the following sequence: VGA Adapter Audio Controller for Multimedia Ethernet Controller 4 4 Panel PC IL Installation Guide Without Operating System

10/01 Installation of the Drivers Using MS Windows 2000 4.1 Installation of the Monitor Mouse for ELO Touchscreen 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive.

33 10/01 Installation of the Drivers Using MS Windows Installation of the Monitor Mouse for ELO Touchscreen 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the ELO Touchscreen are located under the menu item ELO Monitor Mouse for Windows Start the installation by clicking on the icon. The files required for the installation are decompressed in c:\elow2k. 3. Change to the directory \ elow2k in order to install the touchscreen software and execute the Setup. Notice During the installation, ensure that the serial interface COM 2 is defined as the interface for the ELO Touchscreen. Otherwise, the display will not be activated. Panel PC IL Installation Guide Without Operating System 4 5

Installation of the Drivers Using MS Windows 2000 10/01 4.

34 Installation of the Drivers Using MS Windows /01 4. Calibrate the ELO Touchscreen after the installation is complete. Note It is not necessary to restart the PC. 4 6 Panel PC IL Installation Guide Without Operating System

35 10/01 Installation of the Drivers Using MS Windows Installation of the Siemens Virtual Keyboard 1. Insert the "PC IL 70 Documentation & Drivers" CD in the CD-ROM drive. The CD automatically starts Internet Explorer. The drivers for the Siemens Virtual Keyboard are located under menu item Siemens Virtual Keyboard for Windows Me, NT 4.0 & Start the installation by clicking on the icon. The graphics card is automatically installed; the license agreement must be confirmed here. 3. Restart the PC following successful installation. Panel PC IL Installation Guide Without Operating System 4 7

36 Installation of the Drivers Using MS Windows /01 4. After the PC has been restarted, conclude the installation by confirmation with the OK button. The Virtual Keyboard is then started. Your PC is now configured. You can now start with the installation of your applications. 4 8 Panel PC IL Installation Guide Without Operating System

37 Appendix Abbreviations The abbreviations used in this Installation Guide have the following meanings: HMI IF IL PC PLC PU TCP/IP VGA Human Machine Interface Interface Industrial Lite Personal Computer Programmable Logic Controller Programming Unit Transmission Control Protocol/Internet Protocol Video Graphics Array Panel PC IL Installation Guide Without Operating System a

38 Appendix 10/01 b Panel PC IL Installation Guide Without Operating System

Siemens Drives & PLCs

Siemens Drives & PLCs SIMATIC HMI Configuring Text-based Displays Table of Contents Introduction Commissioning Operating Units Product Brief Basic Steps for a Configuration Extend Configuration with Simple Elements Edition