HP 1300 Remanufacturing Instructions Oasis Imaging Products, Inc. Technical Support: ext 110

Transcription

1 HP 1300 Remanufacturing Instructions Oasis Imaging Products, Inc. Technical Support: ext 110 Reference Information: Q2613A Q2613X OEM Yields: 13A % 13X % Materials Needed: Toner Drum PCR (if needed) Mylars (if needed) Wiper Blade Doctor Blade (if needed) Lint free, Wax free wipes Tools Required: #2 Philips Screwdriver Approximate Reman Time: #1 Flat Tip Screwdriver 25 min. 1/8 Punch or smaller 3/32 Drill Bit Power Drill or Screwdriver OEM Chip The HP Laser Jet 1300 toner cartridge has a chip similar to the 4100 cartridge that monitors the toner level. The chip looks similar to the HP 4200/4300 cartridge chips. The chip is not a lock out device, the cartridge will print with a second cycle OEM chip but will give you a display of Non HP Cartridge Detected. The printer will not detect toner low without a new, or replacement chip. Without a new chip the toner low functions on the printer are disabled. 1. The cartridge halves are held together by a pair of retaining pins (Fig.1); one on each end of the cartridge. The cartridge pins will cause damage to the PCR cradle if pushed in; therefore they must be removed from the inside and pushed out. The method of removal in these instructions will cause some minor damage to the cartridge shell, but will not be visible to the end user. Fig Using a small flat head screwdriver, gently pry up on the door hinge with the spring to remove the drum shutter door from the waste bin (Fig. 2). Do the same to the opposite door hinge and carefully remove the shutter door. Fig Once the shutter door is removed you can see the area on figure 3 & 4 that needs to be drilled, so that you can push the cartridge pins out. Fig. 3 Fig. 4 Hewlett Packard LaserJet 1300 Cartridge Remanufacturing Instructions

2 4. Using a 3/32 drill bit carefully drill a small hole into the plastic housing where the cartridge pin is located (Fig. 5). Repeat this process on the opposite side of the cartridge where the second cartridge pin is located (Fig. 6). Fig Once the holes are drilled in the cartridge pin locations you will be able to see the end of the cartridge pin. Use a small punch or angled tool to push the pin out from the inside of the cartridge (Fig. 7). Push the pin out enough so that you can get a pair of pliers on the pin once it is free from the internal housing to fully remove it. Repeat the same steps on the opposite pin (Fig. 8). Once the pins are removed you can separate the cartridge halves. Fig. 6 Fig. 7 Fig Remove the screw that secures the OPC stabilizer (Fig. 9). 7. Once that is done carefully remove the OPC (Fig. 10). 8. Remove the PCR (Fig. 11) Fig. 9. Fig. 10 Fig. 11

3 9. Remove the two screws that secure the wiper blade (Fig 12). Remove the blade and replace if necessary. Remove all residual toner from the waste bin. Check Mylar recovery blade and ensure that it is not creased or damaged. Clean or replace PCR and OPC and reassemble in reverse order. Fig Remove one screw from the end cap on the gear end side of the toner hopper (Fig. 13). Fig Once the end cap is removed remove the gears from the toner hopper. Make a notation of the position of the gears for re -assembly (Fig.14). Fig Remove the one screw on the mag contact end cap on the opposite side of the toner hopper (Fig. 15). Fig. 15

4 13. Carefully remove the magnetic roller by lifting the roller from the toner hopper section (Fig. 16). Note the location of all peripheral components on the mag roller (bushings, etc). Use compressed air to remove all residual toner from the surface of the sleeve and inspect for damage. Fig Remove the two screws that hold the doctor blade in place (Fig. 17). Use compressed air or a vacuum to remove the residual toner from the blade; replace if necessary. Inspect the mag roller Mylar for damage; replace if necessary. Clean the hopper with compressed air or a vacuum; clean the hopper of all residual toner. Fill the toner hopper with the required gram load and prepare for re assembly. Fig Reassemble the toner hopper in reverse order of the disassembly. Clean and inspect all components and replace if necessary (Fig. 18). Place the cartridge halves together and avoid damaging the springs on the top of the toner hopper. Align the pinholes on each side and insert the cartridge pins to hold the halves together. Fig. 18 Oasis and You Succeeding Together!

5 New Hampshire (603) Fax: (603) Tennessee Fax: (901) Texas Canada South America International: (603) Fax: (603) Illinois California Fax: ((714) North Carolina Fax: (603) Europe Netherlands Fax: Oasis Imaging Products, Inc. Any attempt to reproduce any part of these instructions without the written consent of Oasis Imaging Products, Inc. may result in legal action. All registered trademarks are the property of their respective owners.