Addendum to ABB 670 and 650 series version 2.2 IEC Ed.1 MICS

Transcription

1 Addendum to ABB 670 and 650 series version 2.2 IEC Ed.1 MICS (Model Implementation Conformance Statement) Template version 0.1 Date: April 24, 2008 UCA International Users Group Testing Sub Committee Document Review Summary: Reviewer Role Reviewer Name Organization Review Date Review Status Product Architect Johan Sälj TPTE No remarks To be revised Type des. Prep. PSAC/TPTC / Johanna C Doc. kind Declaration of conformity No. of p. Appr. / Svensson Johan O Title Addendum to ABB 670 and 650 series Resp. dept PSAC/TPTC Approved version 2.2 Ed1 - MICS Part no. FILE: Addendum to ABB 650 & 670 series version 2.2 Ed1 - MICS.docx; SAVEDATE: :54; TEMPLATE: Techn_Doc_Stand_P.dot C; SKELETON: 1MRG en A 1 10

2 ABB 670 and 650 series version 2.2 IEC Ed.1 MICS Introduction Scope Denominations Logical Nodes List Logical Node Extensions New Logical Nodes Extended Logical Nodes SMPPTRC Revision ZMMMXU Revision Common Data Class Extensions Enum types Extensions Control Block Extensions MRG en A 2

3 1 Introduction This addendum together with the MICS document for 670 series [1] makes the complete model implementation conformance statement for 670 series This model implementation conformance statement is applicable for ABB 670 Series (REB670, REC670, RED670, REG670, REL670, RES670 and RET670) and 650 Series (REB650, REC650, RED650, REL650, REQ650 and RET650) of version when configured in Edition 1 mode. This MICS document specifies the modelling extensions compared to IEC edition 1 Clause 2 contains the list of implemented logical nodes. Clause 3 describes the new and extended logical nodes. Clause 4 describes the new and extended common data classes (if any). Clause 5 describes the new and extended enum types. Clause 6 describes any other extensions. 1.1 Scope The purpose of this document is to serve as an addendum to the MICS, Modelling Implementation Conformance Statement according to IEC It covers the additions of the products within ABB 670 and 650 Series of version The document contains the description and layout of the Logical Node types, the vendor specific Logical Nodes and the vendor specific additions to the standard Logical Nodes. The details of the respective DATA types are described in the ICD file for the respective products, mentioned above. There is no vendor specific Common Data Classes defined in these products. This document describes the layout of the Logical Nodes types used in the ABB 670 and 650 Series product platform. Each Logical Node type represents a function or a part of a function. The descriptions of the functions and their connection to the logical nodes are described in the Technical reference manuals. From the products definitions, it is a strict relation between the version of a function and the version of each Logical Node type and these are re-used in different products based upon ABB 670 and 650 Series platform. Note that the type versions of the Logical Nodes and their attributes are only unique for each ICD file. This means that during engineering, creating the SCD file(s) of the communication, the tool may change or add content to the type names. 1.2 Denominations Although not required nor defined in IEC 61850, the ABB 670 and 650 Series supports version handling of the Logical Node types. The reason is that it shall be easy to distinguish between the LN types used in different version of the products based upon the same platform and the version of the platform. The revisions of LN type higher than 0 have Revision<No> concatenated with the LN type name. DATA types are not version handled. 1.3 Reference Ref Document id Rev Document title [1] 1MRG A ABB 670 and 650 series version 2.2 IEC Ed.1 MICS 1MRG en A 3

4 2 Logical Nodes List No Logical Nodes have been added in comparison with [1]. 1MRG en A 4

5 3 Logical Node Extensions The following table use M : Data is mandatory in the IEC O: Data is optional in the IEC and is used in the device. E: Data is an extension to the IEC C: Data is conditional in the IEC New Logical Nodes New logical nodes have the lnns attribute in the Name plate. The value of lnns is $, which in this case is a reference to the MICS document. 1.5 Extended Logical Nodes The following Logical Nodes have been update in comparison with [1]. All extra data that has been added, is marked as E (Extended), these data contains the datans attribute with a reference the MICS. LN Class Prefix (default) LN Type Description MMXU ZM ZMMMXU Impedance monitoring PTRC SMP SMPPTRC Single, two or three pole tripping logic SMPPTRC Revision 5 PTRC class Attribute Name DATA Type Explanation M/O/E /C Remarks PTRC Trip logic Data Common Logical Node Information Mod ABB_aINC Mode M Beh ABB_aINS Behaviour M Health ABB_cINS Health M NamPlt ABB_aLPL Name plate M Status Information Op ABB_a_dACT Operate (combination of subscribed Op from protection functions) C Str ABB_h_dACD Start O LORs ABB_v1_dSPC Reset Lockout E Controllable SPTr ABB_v1_dSPS Single Pole Trip E 1MRG en A 5

6 TwoPTr ABB_v1_dSPS Two Pole Trip E TPTr ABB_v1_dSPS Three Pole Trip E ClsLO ABB_v1_dSPS Close Lockout E ZMMMXU Revision 4 MMXU class Attribute Name DATA Type Explanation M/O/E /C Remarks MMXU Impedance monitoring Data Common Logical Node Information Mod ABB_a_dINC Mode M Beh ABB_a_dINS Behaviour M Health ABB_c_dINS Health M NamPlt ABB_a_dLPL Name plate M Status Information Z ABB_m_dWYE Phase impedance O PPZ ABB_v3_dDEL Phase to phase related measured values of a three phase system, magnitude and angle E 1MRG en A 6

7 4 Common Data Class Extensions No common data class extensions have been made. 1MRG en A 7

8 5 Enum types Extensions No Enum types extensions have been made. 1MRG en A 8

9 6 Control Block Extensions No Control block extensions have been made. 1MRG en A 9

10 REVISION Rev. ind. Page (P) Chapt. (C) Description Date Dept./Init. - All New Document TPTC/JO 1MRG en A 10