FACULTY OF ENGINEERING. Lab Experiment
|
|
- Bruce Chandler
- 6 years ago
- Views:
Transcription
1 FACULTY OF ENGINEERING ECE2056 Data Communications and Networking Lab Experiment DCN1: Network Setup and Study Using Routers Last revised: Revised by: GVT
2 Learning Outcome: Pre- Requisite: Instructions: Design a basic local area network through the connections of multiple routers. For the tasks given in this experiment, the students must have completed them in the simulator. Otherwise, it would be a waste of time running this experiment, and it may even damage the equipment used. For the following tasks, remember to capture the screenshots of your work, and put them in your report. 1. Topology a) Connect the routers (e.g., AR2200, AR2220, etc.) according to the topology below. 2. Basic Operations a) Connect a PC to any of the routers (suggested to connect to AR1) using a console cable. b) Run a terminal emulation program such as Putty on the PC to create a connection. c) Select a COM port (COM3 or COM4). The following settings should appear by default but if it does not, set the parameters to: 9600 bits per second 8 data bits No parity 1 stop bit 2
3 No flow control d) Turn on the power switch to start the routers. When the startup process is complete, a command prompt is shown. You are now in User View environment. <Huawei> e) Before the router can be configured, all prior configurations have to be reset or erased from the router s memory. This is done to prevent configuration conflicts. f) To reset the router to the default factory configuration, run the reset saved-configuration command to clear all previous configurations. <Huawei> reset saved-configuration This will delete the configuration in the flash memory. The device configurations will be erased to reconfigure. Are you sure? (y/n) [n]:y Clear the configuration in the device successfully. <Huawei> g) Run the reboot command to restart the devices. <Huawei> reboot Info: The system is comparing the configuration, please wait. Warning: All the configuration will be saved to the next startup configuration. Continue? [y/n]: n System will reboot! Continue? [y/n]: y Info: system is rebooting, please wait h) Once the router has rebooted, run the system-view command to access the System View. Most of the following tasks can only be completed in System View. <Huawei> system-view [Huawei] i) The first thing to do on a router that had been recently erased is to change the device name using the sysname command. [Huawei] sysname AR1 [AR1] j) Repeat steps (a) till (i) for router AR2 and AR3 as in the topology diagram. 3
4 3. Configure IP Address for an Interface a) Configure an IP address for each interface of the routers, following the assignment shown in the topology above. b) Take an example where the GE 0/0/0 interface of router AR1 is assigned with IP address /24. c) Use the command interface gigabitethernet 0/0/0 [AR1] interface gigabitethernet 0/0/0 [AR1-GigabitEthernet0/0/0] d) Then enter the command ip address [AR1-GigabitEthernet0/0/0] ip address [AR1-GigabitEthernet0/0/0] quit [AR1] e) Repeat steps (c) till (d) for all connected interfaces on AR1 (i.e. GE 0/0/1) f) Check the configuration result by running the display currentconfiguration command. [AR1] display current-configuration g) Repeat steps (c) till (f) for AR2 and AR3. 4. Test connectivity between routers a) After completing the configuration, run the ping command to test the connection between any two routers. b) At AR1, try to ping AR2 at the IP address of [AR1] ping PING : 56 data bytes, press CTRL_C to break Reply from : bytes=56 Sequence=1 ttl=255 time = 1 ms Reply from : bytes=56 Sequence=2 ttl=255 time = 2 ms Reply from : bytes=56 Sequence=3 ttl=255 time = 1 ms Reply from : bytes=56 Sequence=4 ttl=255 time = 3 ms Reply from : bytes=56 Sequence=5 ttl=255 time = 2 ms ping statistics packet(s) transmitted 5 packet(s) received 0.00% packet loss round-trip min/avg/max = 1/2/3 ms c) Is there connectivity between AR1 and AR2? 4
5 d) Likewise, attempt the following ping tests: AR1 can ping AR2 AR2 can ping AR3 AR3 can ping AR1 Connections Status (Yes/No) e) Now, from AR2, attempt to ping the IP address of The result will show that there is no connectivity. f) Run the display ip routing-table command to view the routing table of AR2. [AR2] display ip routing-table g) You will notice that the routing table of AR2 does not contain the route to network segment /24. h) If AR2 needs to communicate with this network segment, the route must be configured on AR2. 5. Configure a static route a) In AR2, configure a static route for network segment /24 with the next hop being the IP address of AR3 s GE 0/0/2 interface, by running the command ip route-static [AR2] ip route-static b) Check the IP routing table to confirm the presence of this new entry. Show the content of the IP routing table in your report. c) Run the ping test again. Does it get a positive reply? We can trace the route from AR2 to by running the command tracert [AR2] tracert d) Explain the result in your report. 6. Configure a Backup Static Route a) Now suppose the link between AR2 s GE 0/0/2 and AR3 s GE 0/0/2 is broken. In the lab we can disconnect the cable from the router. In the simulator we can go to a particular interface and run the command shutdown (the reverse is undo shutdown). 5
6 b) Confirm that now AR2 cannot ping c) Check the IP routing table. The static route entry should have now been automatically removed. What is your solution to this problem? d) At AR2, we can configure a backup static route, by running: [AR2] ip route-static preference 80 It is a backup route because its preference value is larger than the default, which is 60. e) Show the IP routing table in your report. f) At AR3, we need to configure a static route that connects AR3 to the network segment /24, by running: [AR3] ip route-static g) Show the IP routing table in your report. h) After configuring the static route, the backup static route takes effect whenever the default static route becomes unavailable. i) The result is that AR2 can now ping even when the direct link between AR2 and AR3 is broken. We can trace the route from AR2 to by running the command tracert Explain the result in your report. 7. Configure a Default Route a) At AR1, ping [AR1] ping PING : 56 data bytes, press CTRL_C to break ping statistics packet(s) transmitted 0 packet(s) received % packet loss b) The result is negative because the route to has not been configured on AR1. 6
7 c) Configure a default route on AR1 to implement network connectivity, by running: [AR1] ip route-static d) Show the IP routing table in your report. e) Now ping again, and report the result. 8. Routing Information Protocol (RIP) Configuration a) Before proceeding with this task, remove ALL the static and default entries previously entered in ALL routers, by running the command undo ip route-static all. [AR1] undo ip route-static all [AR2] undo ip route-static all [AR3] undo ip route-static all b) Confirm that now AR2 cannot ping , and that AR1 cannot ping c) Now, at each router, enable RIP by running the command rip 1 (here the process ID is arbitrarily selected to be 1), and then advertise the network segment to RIP by running the command network [AR1] rip 1 [AR1-rip-1] network [AR1-rip-1] quit [AR2] rip 1 [AR2-rip-1] network [AR2-rip-1] quit [AR3] rip 1 [AR3-rip-1] network [AR3-rip-1] quit d) Now view the routing tables of all routers to confirm that they have learnt the RIP s routes. e) Test the connectivity between any two IP addresses. For example, ping from AR3. We can trace the route from AR3 to by running the command tracert Show your result and explain it. f) Now break the direct link between AR2 and AR3 by either shutting down one of the interfaces or simply disconnect the cable from the router. 7
8 g) Run the command tracert again. What are the changes? Explain. 9. Prepare the report a) Compose a report that consists of the observations of the results of each command/task. Briefly discuss your observations using the questions in the lab sheet as a guide. b) Use the template in the following page as the cover page of your report. 8
9 FACULTY OF ENGINEERING ECE2056 Data Communications and Networking Lab Experiment DCN1: Network Setup and Study Using Routers Student Name: Student ID: Lab Group No.: Degree Major: Declaration of originality: I declare that all sentences, results and data mentioned in this report are from my own work. All work derived from other authors have been listed in the references. I understand that failure to do this is considered plagiarism. I agree that this report will be given 0 marks if any words/photos in this report are copied from others. Student s signature: 9
FACULTY OF ENGINEERING. Lab Experiment
FACULTY OF ENGINEERING ECE2056 Data Communications and Networking Lab Experiment DCN2: Network Setup and Study Using Switches Last revised: 20-11- 2015 Revised by: GVT Learning Outcome: Pre- Requisite:
More informationTable of Contents 1 System Maintaining and Debugging 1-1
Table of Contents 1 System Maintaining and Debugging 1-1 System Maintaining and Debugging 1-1 Ping 1-1 Introduction 1-1 Configuring Ping 1-1 Ping Configuration Example 1-2 Tracert 1-4 Introduction 1-4
More informationThe term "router" in this document refers to both routers and Layer 3 switches. Step Command Remarks. ipv6 host hostname ipv6-address
Contents Configuring IPv6 DNS 1 Overview 1 Configuring the IPv6 DNS client 1 Configuring static domain name resolution 1 Configuring dynamic domain name resolution 1 Displaying and maintaining IPv6 DNS
More informationConfiguring IPv6 DNS. Introduction to IPv6 DNS. Configuring the IPv6 DNS client. Configuring static domain name resolution
Contents Configuring IPv6 DNS 2 Introduction to IPv6 DNS 2 Configuring the IPv6 DNS client 2 Configuring static domain name resolution 2 Configuring dynamic domain name resolution 2 Displaying and maintaining
More informationTable of Contents 1 System Maintenance and Debugging Commands 1-1
Table of Contents 1 System Maintenance and Debugging Commands 1-1 System Maintenance Commands 1-1 ping 1-1 ping ipv6 1-5 tracert 1-6 tracert ipv6 1-7 System Debugging Commands 1-8 debugging 1-8 display
More informationPing, tracert and system debugging commands
Contents Ping, tracert and system debugging commands 1 Ping and tracert commands 1 ping 1 ping ipv6 5 tracert 7 tracert ipv6 9 System debugging commands 10 debugging 10 display debugging 11 i Ping, tracert
More informationTable of Contents 1 System Maintaining and Debugging Commands 1-1
Table of Contents 1 System Maintaining and Debugging Commands 1-1 System Maintaining Commands 1-1 ping 1-1 tracert 1-4 System Debugging Commands 1-6 debugging 1-6 display debugging 1-7 i 1 System Maintaining
More informationLab Configuring HSRP and GLBP Topology
Topology 2014 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 9 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1
More informationH
H12-711 Number: H12-711 Passing Score: 600 Time Limit: 120 min File Version: 1.0 Exam A QUESTION 1 The network administrator wants to improve the performance of network transmission, what steps can the
More informationTable of Contents 1 Static Routing Configuration 1-1
Table of Contents 1 Static Routing Configuration 1-1 Introduction 1-1 Static Route 1-1 Default Route 1-1 Application Environment of Static Routing 1-2 Configuring a Static Route 1-2 Configuration Prerequisites
More informationH
H12-223 Number: H12-223 Passing Score: 600 Time Limit: 120 min Exam A QUESTION 1 The network administrator wants to improve the performance of network transmission, what steps can the administrator take?
More informationTable of Contents 1 Commands for Access Controller Switch Interface Board 1-1
Table of Contents 1 Commands for Access Controller Switch Interface Board 1-1 Commands for Access Controller and Access Controller Switch Interface Board 1-1 acl (user interface view) 1-1 activation-key
More informationContents. Ping, tracert, and system debugging commands 1 debugging 1 display debugging 2 ping 2 ping ipv6 5 tracert 7 tracert ipv6 9
Contents Ping, tracert, and system debugging commands 1 debugging 1 display debugging 2 ping 2 ping ipv6 5 tracert 7 tracert ipv6 9 i Ping, tracert, and system debugging commands debugging Syntax Default
More informationThis is a sample Lab report from ECE 461 from previous years. L A B 6
This is a sample Lab report from ECE 461 from previous years. L A B 6 Part 1 1. o the source and destination M A C/IP addresses change when a packet traverses a bridge? Provide an explanation and include
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 MPLS L2VPN overview 1 About MPLS L2VPN 1 Comparison with traditional VPN 2 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration
More informationLab Troubleshooting Using traceroute Instructor Version 2500
Lab 9.3.4 Troubleshooting Using traceroute Instructor Version 2500 294-833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 9.3.4 Copyright 2003, Cisco Systems, Inc. Objective Use the traceroute Cisco IOS
More informationTable of Contents 1 Static Routing Configuration 1-1
Table of Contents 1 Static Routing Configuration 1-1 Introduction 1-1 Static Route 1-1 Default Route 1-1 Application Environment of Static Routing 1-2 Configuring a Static Route 1-2 Configuration Prerequisites
More informationChapter 10 - Configure ASA Basic Settings and Firewall using ASDM
Chapter 10 - Configure ASA Basic Settings and Firewall using ASDM This lab has been updated for use on NETLAB+ Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet interfaces.
More informationHP 5120 EI Switch Series
HP 5120 EI Switch Series Layer 3 - IP Routing Configuration Guide Part number: 5998-1793 Software version: Release 2220 Document version: 6W100-20130810 Legal and notice information Copyright 2013 Hewlett-Packard
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 MPLS L2VPN overview 1 Basic concepts of MPLS L2VPN 2 Implementation of MPLS L2VPN 2 MPLS L2VPN configuration task list 4 Configuring MPLS L2VPN 5 Configuring CCC MPLS
More informationLab 6-1 Configuring a WLAN Controller
Lab 6-1 Configuring a WLAN Controller Topology Diagram Scenario Step 1 In the next two labs, you will configure a wireless solution involving a WLAN controller, two lightweight wireless access points,
More informationTable of Contents 1 DNS Configuration 1-1
Table of Contents 1 DNS Configuration 1-1 DNS Overview 1-1 Static Domain Name Resolution 1-1 Dynamic Domain Name Resolution 1-1 Configuring Domain Name Resolution 1-3 Configuring Static Domain Name Resolution
More informationCS 386M Lab 1 Router Configuration and Routing
CS 386M Lab 1 Router Configuration and Routing In this lab you will learn: PartA Cisco 2600 Router Configuration Static Routing PartB 30 min Dynamic Routing PartC 40 min Explore! Components used in this
More informationUsing ping, tracert, and system debugging
Contents Using ping, tracert, and system debugging 1 Ping 1 Using a ping command to test network connectivity 1 Ping example 1 Tracert 3 Prerequisites 4 Using a tracert command to identify failed or all
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 Overview 1 Comparison with traditional VPN 1 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration task list 4 Configuring
More informationLab 6-1 Configuring a WLAN Controller
Lab 6-1 Configuring a WLAN Controller Topology Diagram Scenario In the next two labs, you will configure a wireless solution involving a WLAN controller, two lightweight wireless access points, and a switched
More informationBefore you start the lab exercises see the lab administrator or EEE3080F tutor to get assigned to your routers.
EEE00F Lab Basics of the Network Lab Student Lab Manual Before you start the lab exercises see the lab administrator or EEE00F tutor to get assigned to your routers. Contents. Resources used in the labs...
More informationLogin management commands
Contents Login management commands 1 CLI login configuration commands 1 display telnet client configuration 1 telnet 1 telnet ipv6 2 telnet server enable 3 User interface configuration commands 3 acl (user
More informationTable of Contents Chapter 1 IP Addressing Configuration
Table of Contents Table of Contents... 1-1 1.1 IP Addressing Overview... 1-1 1.1.1 IP Address Classes... 1-1 1.1.2 Special Case IP Addresses... 1-2 1.1.3 Subnetting and Masking... 1-3 1.1.4 IP Unnumbered...
More informationContents. Ping, tracert, and system debugging commands 1. debugging 1 display debugging 1 ping 2 ping ipv6 5 tracert 7 tracert ipv6 10
Contents Ping, tracert, and system debugging commands 1 debugging 1 display debugging 1 ping 2 ping ipv6 5 tracert 7 tracert ipv6 10 i Ping, tracert, and system debugging commands debugging Syntax Default
More informationCS356 Lab NIL (Lam) In this lab you will learn: Cisco 2600 Router Configuration Static Routing PartB 20 min Access Control Lists PartC 30 min Explore!
CS356 Lab NIL (Lam) In this lab you will learn: PartA Time: 2 hrs 40 min Cisco 2600 Router Configuration Static Routing PartB 20 min Access Control Lists PartC 30 min Explore! Components used: 2 computers
More informationH3C S7500E Software Upgrade Configuration Examples
H3C S7500E Software Upgrade Configuration Examples Copyright 2015 Hangzhou H3C Technologies Co., Ltd. A l l ri g h t s re s e r ve d. No part of this manual may be reproduced or transmitted in any form
More informationIPv6 ND Configuration Example
IPv6 ND Configuration Example Keywords: IPv6 ND Abstract: This document describes the application environment and typical configuration of IPv6 ND. Acronyms: Acronym Full spelling ARP FIB Address Resolution
More informationLaboration 2 Troubleshooting Switching and First-Hop Redundancy
Laboration 2 Troubleshooting Switching and First-Hop Redundancy Topology All contents are Copyright 1992 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1
More informationLab 6.7.1: Ping and Traceroute
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1-ISP R2-Central Eagle Server S0/0/0 10.10.10.6 255.255.255.252 N/A Fa0/0 192.168.254.253 255.255.255.0 N/A S0/0/0
More informationConfiguring static routing
Contents Configuring static routing 1 Introduction 1 Static route 1 Default route 1 Static route configuration items 1 Configuring a static route 2 Configuration prerequisites 2 Configuration procedure
More informationPreLab for CS356 Lab NIL (Lam) (To be submitted when you come for the lab)
PreLab for CS356 Lab NIL (Lam) (To be submitted when you come for the lab) Name: UT EID: 1. Differentiate between Routers, Switches, and Hubs. 2. Explain subnet masks. 3. For this lab, where is subnet
More informationIP Routing Lab Assignment Configuring Basic Aspects of IP IGP Routing Protocols
IP Routing Lab Assignment Configuring Basic Aspects of IP IGP Routing Protocols 1 PURPOSE AND GOALS This lab assignment will give you a hands-on experience in configuring and managing routers and particularly
More informationLab Capturing and Analyzing Network Traffic
Lab 1.2.2 Capturing and Analyzing Network Traffic Host Name IP Address Fa0/0 Subnet Mask IP Address S0/0/0 Subnet Mask Default Gateway RouterA 172.17.0.1 255.255.0.0 192.168.1.1 (DCE) 255.255.255.0 N/A
More informationH3C S10500 IP Unnumbered Configuration Examples
H3C S10500 IP Unnumbered Configuration Examples Copyright 2015 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means
More informationLab Configuring and Verifying Standard IPv4 ACLs Topology
Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 10 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1
More informationChapter 7 Lab 7-1, Configuring BGP with Default Routing
Chapter 7 Topology Objectives Configure BGP to exchange routing information with two ISPs. Background The International Travel Agency (ITA) relies extensively on the Internet for sales. For this reason,
More informationOperation Manual ARP H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 ARP Overview... 1-1 1.1.1 ARP Function... 1-1 1.1.2 ARP Message Format... 1-1 1.1.3 ARP Address Resolution Process... 1-2 1.1.4 ARP Mapping Table... 1-3 1.2
More informationTable of Contents 1 Static Routing Configuration 1-1
Table of Contents 1 Static Routing Configuration 1-1 Introduction 1-1 Static Route 1-1 Default Route 1-1 Application Environment of Static Routing 1-2 Configuring a Static Route 1-2 Configuration Prerequisites
More informationHP A6600 Routers Network Management and Monitoring. Command Reference. Abstract
HP A6600 Routers Network Management and Monitoring Command Reference Abstract This document describes the commands and command syntax options available for the HP A Series products. This document is intended
More informationHuawei CloudEngine 6850
Huawei CloudEngine 6850 Switch Configuration Guide for Dell EMC SC Series SANs Abstract This document illustrates how to configure Huawei CloudEngine 6850 series switches for use with Dell EMC SC Series
More informationLoopback detection configuration commands
Contents Loopback detection configuration commands 1 display loopback-detection 1 loopback-detection action 2 loopback-detection enable 2 loopback-detection interval-time 3 i Loopback detection configuration
More informationTable of Contents 1 GRE Configuration Point to Multi-Point GRE Tunnel Configuration 2-1
Table of Contents 1 GRE Configuration 1-1 GRE Overview 1-1 Introduction to GRE 1-1 GRE Security Options 1-3 GRE Applications 1-3 Protocols and Standards 1-4 Configuring a GRE over IPv4 Tunnel 1-4 Configuration
More informationLab 3: Basic Device Configuration
Lab 3: Basic Device Configuration University of Jordan Faculty of Engineering & Technology Computer Engineering Department Computer Networks Laboratory 907528 2 Lab 3: Basic Device Configuration **Given
More informationChapter 8 Lab 8-2, Using Manual IPv6 Tunnels with EIGRP for IPv6
Chapter 8 Lab 8-2, Using Manual IPv6 Tunnels with EIGRP for IPv6 Topology Objectives Configure EIGRP for IPv4. Create a manual IPv6 tunnel. Configure EIGRP for IPv6 across the tunnel. Background In this
More informationDr. Tom Hicks. Computer Science Department Trinity University
Dr. Tom Hicks Computer Science Department Trinity University 1 1 Remote Desktop Into CS-X That Contains Your Switch? Open Putty To Your Switch 2 What is the Command To Go Into Privilege Mode DO IT! enable
More informationChapter 8 Lab 8-3, Configuring 6to4 Tunnels
Chapter 8 Lab 8-3, Configuring 6to4 Tunnels Topology Objectives Configure EIGRP for IPv4. Create a 6to4 tunnel. Configure static IPv6 routes. Background In this lab, you configure EIGRP for full connectivity
More informationLab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
More informationLab Configuring and Verifying Standard ACLs Topology
Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 9 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1
More informationIntroduction to Networks: Case Study, Option 2
Introduction to Networks: Case Study, Option 2 Name: Name: Name: Academy username: Academy username: Academy username: Topology Diagram Assessment Objectives For an acceptable Case Study, the student must
More informationH3C SR6600/SR6600-X Routers
H3C SR6600/SR6600-X Routers Network Management and Monitoring Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SR6600X-CMW520-R3103 SR6602-CMW520-R3103 SR6602X_MCP-CMW520-R3103
More informationOperation Manual IP Addressing and IP Performance H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 IP Addressing Overview... 1-1 1.1.1 IP Address Classes... 1-1 1.1.2 Special Case IP Addresses... 1-2 1.1.3 Subnetting and Masking... 1-2 1.2 Configuring IP
More informationLab Assignment 4 ECE374 Spring Posted: 03/22/18 Due: 03/29/18. In this lab, we ll take a quick look at the ICMP and IP protocols.
Lab Assignment 4 ECE374 Spring 2018 Posted: 03/22/18 Due: 03/29/18 In this lab, we ll take a quick look at the ICMP and IP protocols. Whenever possible you should hand in Wireshark screenshots that you
More informationEmergency shell commands 1
Contents Emergency shell commands 1 copy 1 delete 1 dir 2 display copyright 4 display install package 4 display interface m-eth0 5 display ip routing-table 7 display ipv6 routing-table 7 display version
More informationLab 6-1 Configuring a WLAN Controller
Lab 6-1 Configuring a WLAN Controller Topology Diagram Scenario In the next two labs, you will configure a wireless solution involving a router with a built-in WLAN controller, two lightweight wireless
More informationCS 326e Lab 2, Edmondson-Yurkanan, Spring 2004 Router Configuration, Routing and Access Lists
CS 326e Lab 2, Edmondson-Yurkanan, Spring 2004 Router Configuration, Routing and Access Lists Name: In this lab you will learn: PartA Cisco 2600 Router Configuration Static Routing PartB 20 min Dynamic
More informationSkills Assessment (OSPF) Student Training Exam
Skills Assessment (OSPF) Student Training Exam Topology Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 16 Addressing Table Device Interface IP Address Subnet
More informationCCNA Semester 3 labs. Part 1 of 1 Labs for chapters 1 8
CCNA Semester 3 labs Part 1 of 1 Labs for chapters 1 8 2.1.2.12 Lab - Building a Switched Network with Redundant Links 2.3.2.3 Lab - Configuring Rapid PVST+, PortFast and BPDU Guard 2.4.3.4 Lab - Configuring
More informationRealCiscoLAB.com. Chapter 6 Lab 6-1, Configuring BGP with Default Routing. Configure BGP to exchange routing information with two ISPs.
RealCiscoLAB.com CCNPv6 ROUTE Chapter 6 Lab 6-1, Configuring BGP with Default Routing Topology Objectives Background Configure BGP to exchange routing information with two ISPs. The International Travel
More informationH Q&As. HCNA-HNTD (Huawei Network Technology and Device) Pass Huawei H Exam with 100% Guarantee
H12-211 Q&As HCNA-HNTD (Huawei Network Technology and Device) Pass Huawei H12-211 Exam with 100% Guarantee Free Download Real Questions & Answers PDF and VCE file from: 100% Passing Guarantee 100% Money
More informationHP FlexFabric 5700 Switch Series
HP FlexFabric 5700 Switch Series Layer 3 - IP Routing Configuration Guide Part number: 5998-6688 Software version: Release 2416 Document version: 6W100-20150130 Legal and notice information Copyright 2015
More informationThis document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
More information~ 1 ~ Ankara University Department of Computer Engineering COM LAB 1 Part 1
~ 1 ~ Ankara University Department of Computer Engineering COM332 2017 LAB 1 Part 1 SECTION 1 PC Network TCP/IP Configuration Objective Identify tools used to discover a computer network configuration
More informationPacket Tracer - Connect a Router to a LAN (Instructor Version)
(Instructor Version) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Device Interface IP Address Subnet Mask Default
More informationUpgrade 6081RC Firmware
6081RC Upgrade procedure for firmware and CoMon bootloader Date Action Sign-off 1/22/2009 Write initial upgrade procedure for firmware & CoMon bootloader Nathan Meyer 1/27/2009 Edit to simplify procedure
More informationLAB THREE STATIC ROUTING
LAB THREE STATIC ROUTING In this lab you will work with four different network topologies. The topology for Parts 1-4 is shown in Figure 3.1. These parts address router configuration on Linux PCs and a
More informationUsing the emergency shell 1
Contents Using the emergency shell 1 Emergency shell usage guidelines 1 Managing the file systems 1 Obtaining a system image from an FTP/TFTP server 2 Configuring the management Ethernet interface 2 Checking
More informationLab: RIP v2 with VLSM
Lab: RIP v2 with VLSM Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway BRANCH HQ ISP PC1 PC2 PC3 PC4 PC5 Lo1 S0/0/0 Lo1 S0/0/0 S0/0/1 S/0/0/1 Learning Objectives
More informationHuawei CloudEngine 6850
Huawei CloudEngine 6850 Switch Configuration Guide for Dell PS Series SANs Abstract This document illustrates how to configure Huawei CloudEngine 6850 series switches for use with Dell PS Series storage
More informationLab Troubleshooting VTP Configuration
Lab 4.4.3 Troubleshooting VTP Configuration Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask S1 VLAN 99 172.17.99.11 255.255.255.0 S2 VLAN 99 172.17.99.12 255.255.255.0
More informationH3C SR6600 Routers DVPN Configuration Example
H3C SR6600 Routers DVPN Configuration Example Keywords: DVPN, VPN, VAM, AAA, IPsec, GRE Abstract: This document describes the DVPN configuration example for the H3C SR6600 Routers Series. Acronyms: Acronym
More informationRealCiscoLAB.com. Chapter 6 Lab 6-2, Using the AS_PATH Attribute. Topology. Objectives. Background. CCNPv6 ROUTE
RealCiscoLAB.com CCNPv6 ROUTE Chapter 6 Lab 6-2, Using the AS_PATH Attribute Topology Objectives Background Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use
More informationLab 5.6.2: Challenge RIP Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway BRANCH HQ ISP PC1 PC2 PC3 Fa0/0 S0/0/0 Fa0/0 S0/0/0 S0/0/1 Fa0/0 S0/0/1 NIC NIC NIC Learning Objectives Upon completion
More informationLab Using the CLI to Gather Network Device Information Topology
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A Lo0 209.165.200.225 255.255.255.224 N/A S1 VLAN 1 192.168.1.11 255.255.255.0
More informationLab : Challenge OSPF Configuration Lab. Topology Diagram. Addressing Table. Default Gateway. Device Interface IP Address Subnet Mask
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 HQ S0/0/0 S0/0/1 Lo1 10.10.10.1 255.255.255.252 Fa0/0 Branch1 S0/0/0 S0/0/1 Fa0/0 Branch2 S0/0/0 S0/0/1 PC1
More informationRIP V1 with Split Horizon, Route Poisoning, and Poison Reverse. Interpret the contents of the routing table using the show ip route command
RIP V1 with Split Horizon, Route Poisoning, and Poison Reverse Lab 7 This CCNA Video Mentor lab helps you build a deeper understanding of RIP operations, particularly of the effect of distance vector loop-avoidance
More informationTroubleshooting Network analysis Software communication tests and development Education. Protocols used for communication (10 seconds capture)
Lab 1 Wireshark Wireshark is an open source and free packet analyser used for many purposes, such as: Troubleshooting Network analysis Software communication tests and development Education This reports
More informationSkills Assessment (OSPF) Student Training Exam
Skills Assessment (OSPF) Student Training Exam Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 17 Addressing Table Assessment Objectives Device
More informationSkills Assessment (EIGRP) Student Training Exam
Skills Assessment (EIGRP) Student Training Exam Topology Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 15 Addressing Table Device Interface IP Address Subnet
More informationThis document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA 2: Routers
More informationTable of Contents 1 IP Addressing Configuration IP Performance Configuration 2-1
Table of Contents 1 IP Addressing Configuration 1-1 IP Addressing Overview 1-1 IP Address Classes 1-1 Special Case IP Addresses 1-2 Subnetting and Masking 1-2 Configuring IP Addresses 1-3 Displaying IP
More informationConfiguring HSRP. Global Knowledge Training LLC L5-1
L5 Configuring HSRP Global Knowledge Training LLC L5-1 Objectives In this lab you will examine the hot standby router protocol (HSRP). First you will configure PxR2 similar to PxR1, so they are both possible
More informationHP A5120 EI Switch Series IRF. Command Reference. Abstract
HP A5120 EI Switch Series IRF Command Reference Abstract This document describes the commands and command syntax options available for the HP A Series products. This document is intended for network planners,
More informationIntroduction to lab assignments with GNS3
Politecnico di Torino TSR/CNTS, PRL, PAR Introduction to lab assignments with GNS3 User guide and helpful tips Roberto Bonafiglia, Fulvio Risso October 27, 2017 Contents 1 Requirements 4 2 Access to GNS3
More informationSkills Assessment (EIGRP) Student Training Exam
Skills Assessment (EIGRP) Student Training Exam Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 16 Addressing Table Assessment Objectives Device
More informationICMP Computer Networks Lab Lab Course Number: Lab Course Name: Computer Networks (A) 3. Lab Name: ICMP
112039 Computer Networks Lab - 3 ICMP 1. Lab Course Number: 112039 2. Lab Course Name: Computer Networks (A) 3. Lab Name: ICMP 4. Lab Overview: In this lab, we ll investigate the ICMP protocol; examine
More informationH3C SR6600 Routers. Network Management and Monitoring. Command Reference. Hangzhou H3C Technologies Co., Ltd.
H3C SR6600 Routers Network Management and Monitoring Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 20100930-C-1.08 Product Version: SR6600-CMW520-R2420 Copyright
More informationConfiguration and Management of Networks 2012
Configuring BGP with default routing Topology Objectives Background Instructions Configure BGP to exchange routing information with two ISPs. The International Travel Agency (ITA) relies extensively on
More informationChapter 6: Network Layer
Chapter 6: Network Layer Introduction to Networks Intro to Networks v5 Network Layer Intro to Networks v5 2 The Network Layer End to End Transport processes Addressing end devices Encapsulation of Packets
More informationLab Managing the MAC Address Table 2900XL Series
Lab 6.2.3 Managing the MAC Address Table 2900XL Series Objective Create a basic switch configuration. Manage the switch MAC table. Background/Preparation Cable a network similar to the one in the diagram.
More informationInitial Configuration for the Switch
Options for Initial Configuration, page 1 Configuring the Switch Using the Web User Interface, page 1 Configuring the Switch Using the CLI, page 4 Configuring the Switch in the ROMMON Mode, page 12 Options
More informationYour Name: Your student ID number:
CSC 573 / ECE 573 Internet Protocols October 11, 2005 MID-TERM EXAM Your Name: Your student ID number: Instructions Allowed o A single 8 ½ x11 (front and back) study sheet, containing any info you wish
More informationImplement Static Routes for IPv6 Configuration Example
Implement Static Routes for IPv6 Configuration Example Document ID: 113361 Contents Introduction Prerequisites Components Used Conventions Configure Network Diagram Configurations Verify Related Information
More informationContents. Configuring a default route 1 Introduction to default routes 1
Contents Configuring static routing 1 Introduction to static routes 1 Configuring a static route 1 Configuration prerequisites 1 Configuration procedure 1 Configuring BFD for static routes 2 BFD control
More informationLab 4.2.5a Connectivity Tests Ping
Lab 4.2.5a Connectivity Tests Ping Objective Use the ping command to send ICMP datagrams to target host. Verify that the network layer between source and destination is working properly. Retrieve information
More information