Loopback detection configuration commands
|
|
- Sydney Shaw
- 5 years ago
- Views:
Transcription
1 Contents Loopback detection configuration commands 1 display loopback-detection 1 loopback-detection action 2 loopback-detection enable 2 loopback-detection interval-time 3 i
2 Loopback detection configuration commands display loopback-detection display loopback-detection [ { begin exclude include } regular-expression ] Any view 1: Monitor level : Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. Use display loopback-detection to display the operating status of the loopback detection function. # Display the loopback detection operating status. <Sysname> display loopback-detection Loopback-detection is running. Detection interval is 30 second(s). Action mode: None Loopback-detection is enabled on the following VLAN(s): 1, 20, 315, 1001, 2008, , 2026 Loopback is detected on the following interface(s): GigabitEthernet4/0/1 GigabitEthernet4/0/2 Table 1 Command output Field Detection interval is 30 second(s) The loopback detection interval is 30 seconds. 1
3 Field Action mode Loopback detection action: None When detecting a looped port, the system prints log information and sends trap messages. Shutdown When detecting a looped port, the system prints log information, sends trap messages, and shuts down the port. After the port status detection timer (set by the shutdown-interval command) expires, the system will bring up the port. For more information about the port status detection timer, see Fundamentals Configuration Guide. loopback-detection action loopback-detection action { none shutdown } undo loopback-detection action System view none: Sets the loopback detection action to none. If you specify this keyword, the system only prints log information and sends trap messages when it detects a looped port. shutdown: Sets the loopback detection action to shutdown. If you specify this keyword, the system prints log information, sends trap messages, and shuts down the port to disable the port from sending and receiving packets (including loopback detection frames) when it detects a looped port. After the port status detection timer (set by the shutdown-interval command) expires, the system will bring up the port. Use loopback-detection action to configure the loopback detection action. Use undo loopback-detection action to restore the default. By default, the loopback detection action is none. # Set the loopback detection action to shutdown. [Sysname] loopback-detection action shutdown loopback-detection enable In system view: loopback-detection enable vlan { vlan-list all } 2
4 undo loopback-detection enable vlan { vlan-list all } In VLAN view: loopback-detection enable undo loopback-detection enable System view, VLAN view vlan-list: Specifies a list of existing VLANs, in the format of vlan-list = { vlan-id [ to vlan-id ] }&<1-10>, where vlan-id represents the VLAN ID in the range of 1 to 4094, and &<1-10> indicates you can specify up to 10 vlan-id [ to vlan-id ] parameters. all: Specifies all existing VLANs. Use loopback-detection enable to enable loopback detection. Use undo loopback-detection enable to disable loopback detection. By default, the loopback detection function is disabled. In system view, you can enable loopback detection for ports in multiple or all existing VLANs. In VLAN view, you can enable loopback detection only for ports in the VLAN. # Enable loopback detection for VLAN 10 through VLAN 100 in system view. [Sysname] loopback-detection enable vlan 10 to 100 # Enable loopback detection for VLAN 10 in VLAN view. [Sysname] vlan 10 [Sysname-vlan10] loopback-detection enable loopback-detection interval-time loopback-detection interval-time interval undo loopback-detection interval-time System view 3
5 interval: Specifies the loopback detection interval (in seconds) in the range of 1 to 300. Use loopback-detection interval-time to configure the loopback detection interval. Use undo loopback-detection interval-time to restore the default. By default, the loopback detection interval is 30 seconds. # Set the loopback detection interval to 10 seconds. [Sysname] loopback-detection interval-time 10 4
Loop detection commands 1
Contents Loop detection commands 1 display loopback-detection 1 loopback-detection action 1 loopback-detection enable 2 loopback-detection global action 3 loopback-detection global enable 4 loopback-detection
More informationCommand Manual MAC Address Table Management H3C S5500-EI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 MAC Address Table Management... 1-1 1.1.1 display mac-address... 1-1 1.1.2 display mac-address aging-time... 1-2 1.1.3 mac-address (Ethernet port view)...
More informationACSEI configuration commands
Contents ACSEI configuration commands 1 acsei client reboot 1 acsei server 1 acsei server enable 2 acsei timer clock-sync 2 acsei timer monitor 3 display acsei client info 3 display acsei client summary
More informationTable of Contents 1 Ethernet Interface Configuration Commands 1-1
Table of Contents 1 Ethernet Interface Configuration Commands 1-1 broadcast-suppression 1-1 description 1-2 display brief interface 1-3 display interface 1-4 display loopback-detection 1-8 duplex 1-9 flow-control
More informationPPP configuration commands
Contents PPP configuration commands 1 ip address ppp-negotiate 1 ip pool 1 link-protocol ppp 2 ppp authentication-mode 2 ppp chap password 4 ppp chap user 5 ppp ipcp remote-address forced 5 ppp pap local-user
More informationCommand Manual QinQ-BPDU TUNNEL H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 QinQ Configuration Commands... 1-1 1.1.1 qinq enable... 1-1 1.1.2 qinq ethernet-type... 1-2 1.1.3 qinq vid... 1-2 1.1.4 raw-vlan-id inbound... 1-3 Chapter
More informationContents. IP addressing configuration commands 1 display ip interface 1 display ip interface brief 3 ip address 5
Contents IP addressing configuration commands 1 display ip interface 1 display ip interface brief 3 ip address 5 i IP addressing configuration commands display ip interface Syntax View Default level Parameters
More informationHP A5120 EI Switch Series IRF. Command Reference. Abstract
HP A5120 EI Switch Series IRF Command Reference Abstract This document describes the commands and command syntax options available for the HP A Series products. This document is intended for network planners,
More informationHP 5820X & 5800 Switch Series IRF. Command Reference. Abstract
HP 5820X & 5800 Switch Series IRF Command Reference Abstract This document describes the commands and command syntax options available for the HP 5820X & 5800 Series products. This document is intended
More informationEthernet interface commands
Contents Ethernet interface commands 1 Common Ethernet interface commands 1 default 1 description 2 display counters 2 display counters rate 4 display interface 5 display interface brief 12 display packet-drop
More informationEthernet interface configuration commands
Contents Ethernet interface configuration commands 1 General Ethernet interface and subinterface configuration commands 1 alarm-detect 1 bandwidth 2 combo enable 2 default 3 description 4 display counters
More informationOperation Manual ARP H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 ARP Overview... 1-1 1.1.1 ARP Function... 1-1 1.1.2 ARP Message Format... 1-1 1.1.3 ARP Address Resolution Process... 1-2 1.1.4 ARP Mapping Table... 1-3 1.2
More informationPortal configuration commands
Contents Portal configuration commands 1 display portal acl 1 display portal connection statistics 5 display portal free-rule 7 display portal interface 9 display portal-roaming 11 display portal server
More informationHP A3100 v2 Switch Series
HP A3100 v2 Switch Series Layer 2 - LAN Switching Command Reference HP A3100-8 v2 SI Switch (JG221A) HP A3100-16 v2 SI Switch (JG222A) HP A3100-24 v2 SI Switch (JG223A) HP A3100-8 v2 EI Switch (JD318B)
More informationGVRP configuration commands
Contents GVRP configuration commands 1 display garp statistics 1 display garp timer 2 display gvrp local-vlan 3 display gvrp state 3 display gvrp statistics 5 display gvrp status 6 display gvrp vlan-operation
More informationHP MSR Router Series. Layer 2 LAN Switching Command Reference(V7)
HP MSR Router Series Layer 2 LAN Switching Command Reference(V7) Part number: 5998-7738b Software version: CMW710-R0304 Document version: 6PW104-20150914 Legal and notice information Copyright 2015 Hewlett-Packard
More informationEthernet Interface Configuration Commands
Table of Contents Ethernet Interface Configuration Commands 1 General Ethernet Interface/Subinterface Configuration Commands 1 combo enable 1 description 1 display interface 2 display interface brief 9
More informationContents. Tunneling commands 1
Contents Tunneling commands 1 bandwidth 1 default 1 description 2 destination 2 display interface tunnel 3 interface tunnel 7 mtu 8 reset counters interface 9 service 10 shutdown 11 source 11 tunnel dfbit
More informationEthernet Interface Configuration Commands
Table of Contents Ethernet Interface Configuration Commands 1 General Ethernet Interface/Subinterface Configuration Commands 1 combo enable 1 description 1 display interface 2 display interface brief 9
More informationControlled/uncontrolled port and port authorization status
Contents 802.1X fundamentals 1 802.1X architecture 1 Controlled/uncontrolled port and port authorization status 1 802.1X-related protocols 2 Packet formats 2 EAP over RADIUS 4 Initiating 802.1X authentication
More informationContents. Tunneling commands 1
Contents Tunneling commands 1 bandwidth 1 default 1 description 2 destination 3 4 interface tunnel 7 mtu 8 reset counters interface tunnel 9 service 9 shutdown 10 source 11 tunnel dfbit enable 12 tunnel
More informationEthernet interface configuration commands
Contents Ethernet interface configuration commands 1 General Ethernet interface/subinterface configuration commands 1 combo enable 1 default 1 description 2 display counters 3 display counters rate 4 display
More informationHP 5120 SI Switch Series
HP 5120 SI Switch Series Layer 2 - LAN Switching Configuration Guide Part number: 5998-1807 Software version: Release 1513 Document version: 6W100-20130830 Legal and notice information Copyright 2013 Hewlett-Packard
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5101 Document version: 6W100-20111031 Copyright 2011,
More informationHP A5120 EI Switch Series Layer 2 - LAN Switching. Command Reference. Abstract
HP A5120 EI Switch Series Layer 2 - LAN Switching Command Reference Abstract This document describes the commands and command syntax options available for the HP A Series products. This document is intended
More informationHP FlexFabric 5700 Switch Series
HP FlexFabric 5700 Switch Series IRF Command Reference Part number: 5998-6683 Software version: Release 2416 Document version: 6W100-20150130 Legal and notice information Copyright 2015 Hewlett-Packard
More informationH3C S5120-EI Switch Series
H3C S5120-EI Switch Series IP Multicast Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2210 Document version: 6W100-20110915 Copyright 2011, Hangzhou
More informationH3C S12500 sflow Configuration Examples
H3C S12500 sflow Configuration Examples Copyright 2013 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without
More informationTable of Contents 1 PPP Configuration Commands PPPoE Configuration Commands 2-1
Table of Contents 1 PPP Configuration Commands 1-1 PPP Configuration Commands 1-1 ip address ppp-negotiate 1-1 link-protocol ppp 1-2 mtu 1-2 ppp account-statistics enable 1-3 ppp authentication-mode 1-3
More informationTable of Contents Chapter 1 Configuration File Management Commands
Table of Contents Table of Contents... 1-1 1.1.1 display current-configuration... 1-1 1.1.2 display saved-configuration... 1-6 1.1.3 display this... 1-7 1.1.4 display startup... 1-8 1.1.5 reset saved-configuration...
More informationHP 6125G & 6125G/XG Blade Switches
HP 6125G & 6125G/XG Blade Switches Layer 2 - LAN Switching Configuration Guide Part number:5998-3155a Software version: Release 2103 and later Document version: 6W102-20141218 Legal and notice information
More informationARP attack protection commands
Contents ARP attack protection commands 1 Unresolvable IP attack protection commands 1 arp resolving-route enable 1 arp source-suppression enable 1 arp source-suppression limit 2 display arp source-suppression
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series IRF Command Reference Part number: 5998-2881 Software version: Release2207 Document version: 6W100-20121130 Legal and notice information Copyright 2012 Hewlett-Packard Development
More informationH3C S12500 VLAN Configuration examples
H3C S12500 VLAN Configuration examples Copyright 2014 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series Layer 3 - IP Services Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 52xx Document version: 6W102-20131220 Copyright 2013,
More informationH3C SecPath Series Firewalls and UTM Devices
H3C SecPath Series Firewalls and UTM Devices High Availability Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: F100 series: ESS 5132 F1000-A-EI: Feature 3722
More informationHP 5820X & 5800 Switch Series Layer 2 - LAN Switching. Configuration Guide. Abstract
HP 5820X & 5800 Switch Series Layer 2 - LAN Switching Configuration Guide Abstract This document describes the software features for the HP 5820X & 5800 Series products and guides you through the software
More informationTable of Contents. 1 TFTP Configuration Commands 1-1 TFTP Client Configuration Commands 1-1 tftp-server acl 1-1 tftp 1-2 tftp ipv6 1-3
Table of Contents 1 TFTP Configuration Commands 1-1 TFTP Client Configuration Commands 1-1 tftp-server acl 1-1 tftp 1-2 tftp ipv6 1-3 i 1 TFTP Configuration Commands TFTP Client Configuration Commands
More informationH3C SR6600 Routers. Layer 3 IP Services. Command Reference. Hangzhou H3C Technologies Co., Ltd.
H3C SR6600 Routers Layer 3 IP Services Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 20100930-C-1.08 Product Version: SR6600-CMW520-R2420 Copyright 2007-2010,
More informationHP 3600 v2 Switch Series
HP 3600 v2 Switch Series Layer 2 - LAN Switching Command Reference Part number: 5998-2361 Software version: Release 2108P01 Document version: 6W100-20131130 Legal and notice information Copyright 2013
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series Layer 3 - IP Services Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5101 Document version: 6W100-20111031 Copyright 2011,
More informationH3C SR G Core Routers
H3C SR8800 10G Core Routers IP Multicast Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SR8800-CMW520-R3347 Document version: 6W103-20120224 Copyright 2011-2012,
More informationConfiguring GVRP. Introduction to GVRP GARP. How GARP works. GARP messages
Contents Configuring GVRP 1 Introduction to GVRP 1 GARP 1 GVRP 4 Protocols and standards 5 GVRP configuration task list 5 Configuring GVRP functions 5 Configuring GARP timers 6 Displaying and maintaining
More informationTable of Contents. 2 Static Route Configuration Commands 2-1 Static Route Configuration Commands 2-1 delete static-routes all 2-1 ip route-static 2-1
Table of Contents 1 IP Routing Table Commands 1-1 IP Routing Table Commands 1-1 display ip routing-table 1-1 display ip routing-table acl 1-3 display ip routing-table ip-address 1-5 display ip routing-table
More informationHP 5130 EI Switch Series
HP 5130 EI Switch Series IRF Command Reference Part number: 5998-5478a Software version: Release 31xx Document version: 6W100-20150731 Legal and notice information Copyright 2015 Hewlett-Packard Development
More informationHPE FlexNetwork 5510 HI Switch Series
HPE FlexNetwork 5510 HI Switch Series Layer 3 IP Services Command Reference Part number: 5200-0078b Software version: Release 11xx Document version: 6W102-20171020 Copyright 2015, 2017 Hewlett Packard
More informationH3C WX3000E Series Wireless Switches
H3C WX3000E Series Wireless Switches Switching Engine Layer 2 Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: WX3000-CMW520-R3507P26 Document version: 6W101-20140714
More informationTable of Contents 1 WLAN Security Configuration Commands 1-1
Table of Contents 1 WLAN Security Configuration Commands 1-1 authentication-method 1-1 cipher-suite 1-2 gtk-rekey client-offline enable 1-2 gtk-rekey enable 1-3 gtk-rekey method 1-4 ptk-lifetime 1-5 security-ie
More informationH3C S5120-HI Switch Series
H3C S5120-HI Switch Series Layer 3 - IP Services Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 52xx Document version: 6W101-20140523 Copyright 2013-2014,
More informationH3C S3100V2 Switch Series
H3C S3100V2 Switch Series Layer 3 IP Services Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5203P05 and Release 5203P12 Document version: 6W101-20150530
More informationConfiguring Port-Based Traffic Control
CHAPTER 18 This chapter describes how to configure port-based traffic control features on the Catalyst 3750 Metro switch. For complete syntax and usage information for the commands used in this chapter,
More informationHP A3100 v2 Switch Series
HP A3100 v2 Switch Series Layer 2 - LAN Switching Configuration Guide HP A3100-8 v2 SI Switch (JG221A) HP A3100-16 v2 SI Switch (JG222A) HP A3100-24 v2 SI Switch (JG223A) HP A3100-8 v2 EI Switch (JD318B)
More informationtcp ipv6 timer fin-timeout 40 tcp ipv6 timer syn-timeout 40 tcp ipv6 window 41
Table of Contents IPv6 Basics Configuration Commands 1 IPv6 Basics Configuration Commands 1 display ipv6 fib 1 display ipv6 fibcache 2 display ipv6 interface 2 display ipv6 neighbors 5 display ipv6 neighbors
More informationH3C S3100V2-52TP Switch
H3C S3100V2-52TP Switch Layer 3 IP Services Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2111P02, Release 2112 Document version: 6W101-20180228 Copyright
More informationIP Services Volume Organization
IP Services Volume Organization Manual Version 6W100-20090626 Product Version Release 1102 Organization The IP Services Volume is organized as follows: Features IP Address IP Performance Optimization ARP
More informationConfiguring Port Security
33 CHAPTER This chapter describes how to configure port security on the Catalyst 4500 series switch. It provides an overview of port security on the Catalyst 4500 series switch and details the configuration
More informationHPE FlexNetwork HSR6800 Routers
HPE FlexNetwork HSR6800 Routers IRF Configuration Guide Part number: 5998-4487R Software version: HSR6800-CMW520-R3303P25 Document version: 6W105-20151231 Copyright 2015 Hewlett Packard Enterprise Development
More informationContents. FCoE commands 0
Contents FCoE commands 0 FCoE mode commands 0 display fcoe-mode 0 fcoe-mode 0 VFC interface commands 2 bandwidth 2 bind interface 2 default 3 description 4 display interface vfc 5 fc mode 8 interface vfc
More informationCommand Manual (For Soliton) IP Address-IP Performance. Table of Contents
Table of Contents Table of Contents Chapter 1 IP Address Configuration... 1-1 1.1 IP Address Configuration... 1-1 1.1.1 display ip interface... 1-1 1.1.2 display ip interface brief... 1-3 1.1.3 ip address...
More informationH3C S3100V2 Switch Series
H3C S3100V2 Switch Series Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5103 Document version: 6W100-20110620 Copyright 2011,
More informationH3C S5820X&S5800 Switch Series
H3C S5820X&S5800 Switch Series OAA Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 1211 Document version: 6W100-20110415 Copyright 2011, Hangzhou H3C
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series IP Multicast Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5101 Document version: 6W100-20111031 Copyright 2011, Hangzhou
More informationHP 3600 v2 Switch Series
HP 3600 v2 Switch Series IRF Configuration Guide Part number: 5998-2349a Software version: Release 2108P01 Document version: 6W100-20131130 Legal and notice information Copyright 2013 Hewlett-Packard Development
More informationH3C S9500E Series Routing Switches
H3C S9500E Series Routing Switches IP Multicast Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: S9500E-CMW520-R1828P04 Document version: 6W182-20140823 Copyright
More informationIP performance optimization
Contents IP performance optimization 1 display icmp statistics 1 display ip socket 2 display ip statistics 6 display tcp statistics 8 display udp statistics 10 ip forward-broadcast 11 ip icmp flow-control
More informationNOTE: The S9500E switch series supports HDLC encapsulation only on POS interfaces. Enabling HDLC encapsulation on an interface
Contents Configuring HDLC 1 Overview 1 HDLC frame format and frame type 1 Enabling HDLC encapsulation on an interface 1 Configuring an IP address for an interface 2 Configuring the link status polling
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 MPLS L2VPN overview 1 About MPLS L2VPN 1 Comparison with traditional VPN 2 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 Overview 1 Comparison with traditional VPN 1 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration task list 4 Configuring
More informationHP FlexFabric 5700 Switch Series
HP FlexFabric 5700 Switch Series Layer 2 LAN Switching Configuration Guide Part number: 5998-6686 Software version: Release 2416 Document version: 6W100-20150130 Legal and notice information Copyright
More informationHPE 5920 & 5900 Switch Series
HPE 5920 & 5900 Switch Series Layer 3 IP Services Command Reference Part number: 5998-6643t Software version: Release 2422P01 Document version: 6W101-20171030 Copyright 2016, 2017 Hewlett Packard Enterprise
More informationHPE FlexNetwork 5510 HI Switch Series
HPE FlexNetwork 5510 HI Switch Series Layer 3 IP Services Command Reference Part number: 5200-3837 Software version: Release 13xx Document version: 6W100-20170315 Copyright 2015, 2017 Hewlett Packard Enterprise
More informationH3C S5820X&S5800 Series Ethernet Switches
H3C S5820X&S5800 Series Ethernet Switches Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 6W103-20100716 Product Version: Release 1110
More informationH3C S12500 Series Routing Switches
H3C S12500 Series Routing Switches Layer 3 IP Services Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: S12500-CMW710-R7128 Document version: 6W710-20121130 Copyright
More informationConfiguring IGMP Snooping and Filtering
CHAPTER 18 This chapter describes how to configure Internet Group Management Protocol (IGMP) snooping on the Catalyst 4500 series switch. It provides guidelines, procedures, and configuration examples.
More informationConfiguring VPLS. VPLS overview. Operation of VPLS. Basic VPLS concepts
Contents Configuring VPLS 1 VPLS overview 1 Operation of VPLS 1 VPLS packet encapsulation 4 H-VPLS implementation 5 Hub-spoke VPLS implementation 7 Multi-hop PW 8 VPLS configuration task list 9 Enabling
More informationContents. RMON commands 1
Contents RMON commands 1 display rmon alarm 1 display rmon event 2 display rmon eventlog 3 display rmon history 5 display rmon prialarm 7 display rmon statistics 9 rmon alarm 10 rmon event 13 rmon history
More informationThe term "router" in this document refers to both routers and Layer 3 switches. Step Command Remarks. ipv6 host hostname ipv6-address
Contents Configuring IPv6 DNS 1 Overview 1 Configuring the IPv6 DNS client 1 Configuring static domain name resolution 1 Configuring dynamic domain name resolution 1 Displaying and maintaining IPv6 DNS
More informationConfiguring IGMP Snooping and Filtering
CHAPTER 20 This chapter describes how to configure Internet Group Management Protocol (IGMP) snooping on the Catalyst 4500 series switch. It provides guidelines, procedures, and configuration examples.
More informationH3C S6800 Switch Series
H3C S6800 Switch Series OpenFlow Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2609 and later Document version: 6W103-20190104 Copyright 2019, New H3C Technologies
More informationConfiguring IPv6 DNS. Introduction to IPv6 DNS. Configuring the IPv6 DNS client. Configuring static domain name resolution
Contents Configuring IPv6 DNS 2 Introduction to IPv6 DNS 2 Configuring the IPv6 DNS client 2 Configuring static domain name resolution 2 Configuring dynamic domain name resolution 2 Displaying and maintaining
More informationConfiguring HSRP. Understanding HSRP CHAPTER
CHAPTER 40 This chapter describes how to use Hot Standby Router Protocol (HSRP) on the Cisco ME 3400E Ethernet Access switch to provide routing redundancy for routing IP traffic without being dependent
More informationH3C SecPath Series High-End Firewalls
H3C SecPath Series High-End Firewalls Attack Protection Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SECPATHF1000SAI&F1000AEI&F1000ESI-CMW520-R3721 SECPATH5000FA-CMW520-F3210
More informationConfiguring Port-Based Traffic Control
CHAPTER 17 This chapter describes how to configure the port-based traffic control features on your switch. For complete syntax and usage information for the commands used in this chapter, refer to the
More informationHP 5500 HI Switch Series
HP 5500 HI Switch Series IRF Configuration Guide Part number: 5998-2376a Software version: Release 5203 and Release 5206 Document version: 6W102-20140228 Legal and notice information Copyright 2014 Hewlett-Packard
More informationTable of Contents 1 IP Address Configuration Commands IP Performance Configuration Commands 2-1
Table of Contents 1 IP Address Configuration Commands 1-1 IP Address Configuration Commands 1-1 display ip interface 1-1 display ip interface brief 1-2 ip address 1-3 2 IP Performance Configuration Commands
More informationTable of Contents. 2 MIB Configuration Commands 2-1 MIB Configuration Commands 2-1 display mib-style 2-1 mib-style 2-1
Table of Contents 1 SNMP Configuration Commands 1-1 SNMP Configuration Commands 1-1 display snmp-agent community 1-1 display snmp-agent group 1-2 display snmp-agent local-engineid 1-3 display snmp-agent
More informationHP Unified Wired-WLAN Products
HP Unified Wired-WLAN Products Security Command Reference HP 830 Unified Wired-WLAN PoE+ Switch Series HP 850 Unified Wired-WLAN Appliance HP 870 Unified Wired-WLAN Appliance HP 11900/10500/7500 20G Unified
More informationHP FlexFabric 5930 Switch Series
HP FlexFabric 5930 Switch Series Layer 3 IP Services Command Reference Part number: 5998-4568 Software version: Release 2406 & Release 2407P01 Document version: 6W101-20140404 Legal and notice information
More informationConfiguring Port-Based Traffic Control
CHAPTER 22 This chapter describes how to configure the port-based traffic control features on the Cisco ME 3400 Ethernet Access switch. For complete syntax and usage information for the commands used in
More informationVPLS configuration commands
Contents VPLS configuration commands 1 bandwidth 1 broadcast-restrain 1 description 2 display bgp vpls 3 display l2vpn fast-switch-group 8 display mac-address vsi 9 display mpls l2vpn fib ac vpls 10 display
More informationHP 5820X & 5800 Switch Series IRF. Configuration Guide. Abstract
HP 5820X & 5800 Switch Series IRF Configuration Guide Abstract This document describes the software features for the HP 5820X & 5800 Series products and guides you through the software configuration procedures.
More informationOperation Manual Cluster Management. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 HGMP V1 Over... 1-1 1.2 HGMP Server Configuration... 1-2 1.2.1 Enabling HGMP Server on a Management Device... 1-2 1.2.2 Upgrading Software on a Switch through
More informationHPE VSR1000 Virtual Services Router
HPE VSR1000 Virtual Services Router High Availability Command Reference Part number: 5200-3170 Software version: VSR1000_HPE-CMW710-E0518-X64 Document version: 5W100-20170314 Copyright 2017 Hewlett Packard
More informationHP FlexFabric 5700 Switch Series
HP FlexFabric 5700 Switch Series FCoE Command Reference Part number: 5998-6675 Software version: Release 2416 Document version: 6W100-20150130 Legal and notice information Copyright 2015 Hewlett-Packard
More informationH3C S5130-HI Switch Series
H3C S5130-HI Switch Series Layer 3 - IP Services Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 1111 Document version: 6W100-20150615 Copyright 2015,
More informationVPLS configuration commands
Contents VPLS configuration commands 1 car 1 description 1 display bgp vpls 2 display l2vpn fast-switch-group 7 display mac-address vsi 8 display mpls l2vpn fib ac vpls 10 display mpls l2vpn fib pw vpls
More informationConfiguring MSDP. Overview. How MSDP operates. MSDP peers
Contents Configuring MSDP 1 Overview 1 How MSDP operates 1 MSDP support for VPNs 6 Protocols and standards 6 MSDP configuration task list 7 Configuring basic MSDP functions 7 Configuration prerequisites
More informationH3C S5130-HI Switch Series
H3C S5130-HI Switch Series Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 1111 Document version: 6W100-20150615 Copyright 2015,
More informationCommand Manual IPv4 Routing H3C S3610&S5510 Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents Chapter 1 Static Routing Configuration Commands... 1-1 1.1 Static Routing Configuration Commands... 1-1 1.1.1 delete static-routes all... 1-1 1.1.2 ip route-static...
More informationH3C S12500 Unauthorized DHCP Server Detection Configuration Examples
H3C S12500 Unauthorized DHCP Server Detection Configuration Examples Copyright 2013 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any
More information