Installation Manual Type PG-B3
|
|
- Lynne Carson
- 6 years ago
- Views:
Transcription
1 YASKAWA AC Drive-Option Card Complementary Type PG Installation Manual Type PG-B3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user receives this manual. PG PG-B3 MANUAL NO. TOBP C A
2 This Page Intentionally Blank
3 Table of Contents 1 PREFACE PRODUCT OVERVIEW OPTION CARD COMPONENTS ELECTRICAL INSTALLATION RELATED PARAMETERS TROUBLESHOOTING SPECIFICATIONS & WARRANTY INFORMATION Copyright 2008 YASKAWA ELECTRIC CORPORATION All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of Yaskawa. No patent liability is assumed with respect to the use of the information contained herein. Moreover, because Yaskawa is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without notice. Every precaution has been taken in the preparation of this manual. Yaskawa assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in this publication. YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 3
4 1 Preface 1 Preface Yaskawa manufactures products used as components in a wide variety of industrial systems and equipment. The selection and application of Yaskawa products remain the responsibility of the equipment manufacturer or end user. Yaskawa accepts no responsibility for the way its products are incorporated into the final system design. Under no circumstances should any Yaskawa product be incorporated into any product or design as the exclusive or sole safety control. Without exception, all controls should be designed to detect faults dynamically and fail safely under all circumstances. All systems or equipment designed to incorporate a product manufactured by Yaskawa must be supplied to the end user with appropriate warnings and instructions as to the safe use and operation of that part. Any warnings provided by Yaskawa must be promptly provided to the end user. Yaskawa offers an express warranty only as to the quality of its products in conforming to standards and specifications published in the Yaskawa manual. NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS OFFERED. Yaskawa assumes no liability for any personal injury, property damage, losses, or claims arising from misapplication of its products. Applicable Documentation This instruction manual has been written for the items listed below. Use this option card for its intended purpose only. Option Card YASKAWA AC Drive-Option Card Complementary PG: PG-B3 Installation Manual (this book) Document Number: TOBP C Read this manual first. It contains information required to install the option card and set up related drive parameters. Drive Refer to the manual of the drive this option card is being used with. The manual for the drive covers basic installation, wiring, operation procedures, functions, troubleshooting, and maintenance information. It also includes important information on parameter settings and how to tune the drive. To obtain instruction manuals for Yaskawa products access these sites: Europe: Japan: Other areas: contact a Yaskawa representative. 4 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
5 1 Preface Registered Trademarks Company names and product names listed in this manual are the registered trademarks of those companies. Supplemental Safety Information Read and understand this manual before installing, operating or servicing this option unit. The option unit must be installed according to this manual and local codes. The following conventions are used to indicate safety messages in this manual. Failure to heed these messages could result in serious or possibly even fatal injury or damage to the products or to related equipment and systems. DANGER Indicates a hazardous situation, which, if not avoided, will result in death or serious injury. W ARNING Indicates a hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury. Indicates an equipment damage message. NOTICE YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 5
6 1 Preface General Safety General Precautions The diagrams in this section may include option units and drives without covers or safety shields to illustrate details. Be sure to reinstall covers or shields before operating any devices. The option board should be used according to the instructions described in this manual. Any illustrations, photographs, or examples used in this manual are provided as examples only and may not apply to all products to which this manual is applicable. The products and specifications described in this manual or the content and presentation of the manual may be changed without notice to improve the product and/or the manual. When ordering a new copy of the manual due to damage or loss, contact your Yaskawa representative or the nearest Yaskawa sales office and provide the manual number shown on the front cover. DANGER Heed the safety messages in this manual. Failure to comply will result in death or serious injury. The operating company is responsible for any injuries or equipment damage resulting from failure to heed the warnings in this manual. NOTICE Do not expose the drive to halogen group disinfectants. Failure to comply may cause damage to the electrical components in the option unit Do not pack the drive in wooden materials that have been fumigated or sterilized. Do not sterilize the entire package after the product is packed. 6 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
7 2 Product Overview 2 Product Overview Regarding this Product By installing this option card to a drive, the drive is able to read a feedback signal send from a pulse generator (PG) attached to the motor. This PG signal lets the drive know about any subtle variations in the load, and provides the drive with the data necessary for controlling the output frequency to maintain constant speed with a high degree of accuracy. This card can read a maximum input frequency sent from the PG of 50 khz. Select a PG with an output of maximum 20 khz when operating at maximum speed. This option card allows the user to connect a incremental encoder (PG) for motor speed feedback to the drive and take advantage of the drive s V/f with PG control mode, Closed Loop Vector control mode, and Closed Loop Vector for PM motors to obtain more accurate control and higher performance. Checking Package Contents Table 1 Items Included with this Option Card Package Contents Option Card Lead Lines (for grounding) Screws (M3) Manual (this book) MANUAL Number of Items Inspect the Option Card for damage. If the Option Card appears damaged upon receipt, contact the shipper immediately. Verify receipt of the correct model by checking the model number printed on the Name plate of the Option Card. (see Figure 1) If you have received the wrong model or the Option Card does not function properly, contact your supplier. YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 7
8 2 Product Overview Tools Required for Installation A Phillips screwdriver PH1 (#1) is needed to install this option card. Additionally a straight-edge screwdriver (blade depth: 0.4 mm, width: 2.5 mm) will be needed to wire the terminal block. Note: Other tools are required for preparing encoder cables. 8 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
9 3 Option Card Components 3 Option Card Components Option Card Figure 1 D A PG-B3 E F Underside B C A Terminal block TB1 B Ground terminal (installation hole) C Terminal block TB2 D Model number E Installation hole F Connector (CN5) Figure 1 Option Card Terminal Block Figure 2 IP IG AO IG BO IG ZO IG TB2 TB1 A+ A- B+ B- Z+ Z- SD FE Figure 2 Terminal Block YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 9
10 4 Electrical Installation 4 Electrical Installation Safety Messages DANGER Electric Shock Hazard Power to the drive must be shut off when installing this option card. Even though the power has been shut off, voltage still remains in the drive s DC bus. Wait before removing the front cover once the drive has been turned off. The CHARGE light on the drive will go out after voltage in the DC bus drops below 50 V, at which point it is safe to remove the front cover. Due to the risk of electric shock, be sure that all LEDs have gone out and that the DC bus voltage has reached a safe level prior to performing any work on the drive. W ARNING Electrical Shock Hazard Do not allow unqualified personnel to perform work on the drive. Failure to comply could result in death or serious injury. Maintenance, inspection, and replacement of parts must be performed only by authorized personnel familiar with installation, adjustment and maintenance of AC drives and Option Cards. 10 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
11 4 Electrical Installation NOTICE Damage to Equipment Observe proper electrostatic discharge procedures (ESD) when handling the option unit, drive, and circuit boards. Failure to comply may result in ESD damage to circuitry. Never shut the power off while the drive is outputting voltage. Failure to comply may cause the application to operate incorrectly or damage the drive. Do not operate damaged equipment. Failure to comply may cause further damage to the equipment. Do not connect or operate any equipment with visible damage or missing parts. Properly connect all pins and connectors. Failure to comply may prevent proper operation and possibly damage equipment. YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 11
12 4 Electrical Installation Installing the Option Card This option card can be inserted into the either the CN5-B or CN5-C connectors located on the drive s control board. If only one option card is connected to the drive, use the CN5-C connector. If two option cards are connected, use both CN5-B and CN5-C. See the drive manual for directions on removing the front cover. 1. Shut off power to the drive, wait the appropriate amount of time for voltage to dissipate, then remove the operator and front cover. 2. Insert the CN5 connector on the option card into the matching CN5 connector on the drive, then fasten it into place using one of the screws included with the option card. Connect one of the lead lines using one of the screws to the ground terminal. Two separate lead lines have been included with the option card. Use the longer one when the option card is plugged into connector CN5-C on the drive side. Use Figure 3 Note: the shorter one if it is plugged into connector CN5-B. There are only two screw holes on the drive for ground terminals. If three option cards are connected, two of the lead lines will need to share the same ground terminal. A E B C F G J D K H I L A Connector CN5-C G Mounting screw B Connector CN5-B H Lead line C Connector CN5-A I Use wire cutters to create an opening for cable lines D Drive grounding terminal (FE) J Front cover E Insert connector CN5 here K Digital operator F Option card L Terminal cover Figure 3 Installing an Option Card 12 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
13 4 Electrical Installation Figure 4 3. Wire the option card to the terminal block on the option card. For wiring instructions, see Complementary Output on page 15 and Open- Collector Outputs on page 15. In the drives CIMR-A 2A0004 to 0040 and 4A0002 to 0023 the PG cable might need to be routed through the top cover to the outside. In this case cut out the perforated openings at the left side of the drive top cover. Make sure no sharp edges that can damage the cable remain. In the drives CIMR-A 2A0056 to 0211 and 4A0031 to 0165 the PG cable can be routed inside the drive. A B A Wires should pass through the access hold provided on the left side of the front cover. (CIMR-A 2A0004 to 0040, 4A0002 to 0023) B Use the open space provided inside the drive to route option card wiring. (CIMR-A 2A0056 to 0211, 4A0031 to 0165) Figure 4 Wiring space 4. Place the front cover back onto the drive as it was before. Note: 1. Take care when wiring the option card so that the front cover easily fits back onto the drive. Make sure a cable is not caught between the front cover and the drive when putting the cover back on. 2. The drive will not be used as NEMA Type1 if there is any exposed wiring outside the enclosure. YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 13
14 4 Electrical Installation Connection Diagram Refer to Figure 5 when wiring the terminal block on the option card. If using a single track encoder in the V/f with PG control mode, connect the pulse output from the PG to the option card and set parameter F1-37 in the drive to 0. If using a two track encoder, then connect the A and B pulse outputs on the PG to the option card and set F1-37 to 1. If using a two track encoder for the Close Loop Vector control mode, connect pulse outputs A and B from the encoder to the corresponding terminals on the option card. For a three track encoder, connect the A, B, and Z pulse outputs to the corresponding terminals on the option card. A detailed description of the option board terminals can be found in Terminal Functions on page 16. For a description of the PG cable, see PG Cables on page 17. For instructions on making your own cable, see Wire Gauges and Tightening Torque on page 18. Figure 5 R/L1 S/L2 T/L3 U/T1 V/T1 W/T1 M Drive PG B3 TB1 A+ A B+ B Z+ Z PG NC SD FE TB2 IP IG FE CN5 AO IG BO IG ZO IG A pulse monitor signal B pulse monitor signal Z pulse monitor signal Lead line twisted-pair shielded line main circuit terminal control circuit terminal Figure 5 Wiring the Option Card and PG 14 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
15 4 Electrical Installation Take the following steps to prevent erroneous operation caused by noise interference: Use shielded wire for the signal lines. Keep complementary output wiring under 100 m. Lines for open-collector output should kept under 50 m. Make sure that control lines to the option card, main circuit wiring, and power lines are separated from one another. Interface Circuit Complementary Output Figure 6 PG B3 12 V 330 Ω IP A+,B+,Z+ Vcc A,B,Z PG 470 Ω 330 Ω A,B,Z IG AO,BO,ZO IG 0V 0V Monitor Signal Figure 6 Complementary Outputs for the Interface Circuit Open-Collector Outputs Figure 7 PG B3 IP Vcc 12 V PG 330 Ω A+,B+,Z+ 470 Ω A,B,Z A,B,Z 330 Ω IG 0V AO,BO,ZO IG Monitor Signal Figure 7 Open-Collector Outputs for the Interface Circuit YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 15
16 4 Electrical Installation Terminal Functions Terminal Block Table 2 Terminal Functions PG Signal Output and Option Card Settings With a two or three track encoder the motor rotation direction is determined by the pulse that leads. A PG signal with leading A pulse is considered as rotation in Forward direction (counter-clockwise when from the load side). NOTICE: Make sure that the option card and PG have been set correctly to ensure that the motor operates as expected. Figure 8 TB1 TB2 Terminal Function Description A+ A+ pulse signal input Pulse signal inputs from the PG. A A inverse pulse input Signal inputs from complementary and open-collector B+ B+ pulse signal input outputs B B inverse pulse input Signal level H level: 8 to 12 V Z+ Z+ pulse signal input L level: 2.0 V or less Z Z inverse pulse input SD NC pin (open) For use when cables shields should not be grounded FE Ground Used for grounding shielded lines IP PG power supply Output voltage: 12.0 V ± 5% IG PG power supply common Max output current: 200 ma <1> AO A pulse monitor signal Outputs the monitor signal for the A, B, and Z pulses from BO B pulse monitor signal the PG speed control card For open collector outputs from the option card ZO Z pulse monitor signal Max voltage: 24 V IG Monitor signal common Max current: 30 ma <1> A separate power supply is needed if the PG requires more than 200 ma to operate. To continue operating through a momentary power loss, a back-up capacitor should be connected. A pulse The A pulse leads, followed by the B pulse displaced at 90 degrees B pulse Time Figure 8 Displacement of A and B Pulses After connecting the PG outputs to the option card, the direction can be checked by manually rotate the motor with the monitor on the drive. If the monitor shows the forward direction as being the opposite of what you want, set parameter F1-05/F1-32 to 1 to switch the direction of how the option card reads pulses from the PG output. 16 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
17 4 Electrical Installation PG Cables For cables running between the option card and the PG, Yaskawa recommends using a LMA- B-S185Y (complementary output) as show in Figure 9. For instructions on wiring the terminal block, see Terminal Functions on page 16. Figure 9 TB1 TB2 A+ A- B+ B- Z+ Z- SD FE IP IG AO IG BO IG ZO IG E 1 2 TA1 PG side A G B C H D F E Pin No. Figure 9 Wiring PG Cables Table 3 Connecting the PG Cable Option Card PG Cable Terminal Wire No. Color Pin No. IP 1 Blue C IG 2 White H A+ 3 Yellow B A 4 White G B+ 5 Green A B 6 White F FE E N/A (shield) D Table 4 PG Cable Types Length Type Length Type 10 m W m W m W m W5100 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 17
18 4 Electrical Installation Wire Gauges and Tightening Torque Wire gauge specifications are listed below in Table 5. Yaskawa recommends using crimp terminals for easy of wiring and to ensure proper connection. Crimp terminal specifications can be found in Table 6. Table 5 Wire Gauges and Tightening Torque Terminal Signal A+, A, B+, B, Z+, Z, FE, IP, IG AO, IG, BO, IG, ZO, IG Screw Size Tightening Torque (N m) M to 0.25 Bare Cable Possible Gauges mm 2 (AWG) Stranded wire: 0.25 to 1.0 (24 to 17) Single line: 0.25 to 1.5 (24 to 16) Recom mended Gauges mm 2 (AWG) 0.75 (18) Wiring Gauges with Crimp Terminals Possible Gauges mm 2 (AWG) 0.25 to 0.5 (24 to 20) Recom mended Gauges mm 2 (AWG) 0.5 (20) Wire Type Shielded twisted pair, etc. Shielded line, etc. Crimp Terminals Yaskawa recommends using CRIMPFOX ZA-3 by Phoenix Contact to crimp the terminal ends. NOTICE: Wire ends should be properly trimmed so no wire extends out from the crimp terminals. Table 6 Crimp Terminal Sizes Wire Gauge mm 2 (AWG) Model L (mm) d1 (mm) d2 (mm) Manufacturer 0.25 (24) AI YE d1 6 mm L d (22) AI TQ (20) AI 0.5-6WH Phoenix Contact 18 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
19 4 Electrical Installation Wiring Procedure When wiring the option card, wire ends should be prepared as shown in Figure 10. See Wire Gauges and Tightening Torque on page 18 to make sure that the proper tightening torque is applied to each terminal end. Take particular precautions to ensure that each cable is properly connected, and that wire covering has not been accidentally inserted into the terminals. NOTICE: Insulation or tape may be required to ensure that shielded lines do not come into contact with other wiring. Insufficient insulation may cause a short circuit that can damage the option card and the drive. NOTICE: Follow the tightening torque specifications in this manual for all terminal screws. Failing to do so may keep the drive from functioning properly and could damage the terminal block. Figure 10 Shield Insulation Option Card PG Ground Terminal FE/SD Shield shearth (Insulate with tape) Figure 10 Treating Terminal Ends for Shielded Line Figure 11 Avoid fraying wire stands when stripping insulation from wire. Strip length 5.5 mm Blade depth of 0.4 mm or less Blade width of 2.5 mm or less Terminal block Loosen screw to insert wire. Single wire or stranded wire Figure 11 Terminal Block Wiring YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 19
20 5 Related Parameters 5 Related Parameters The following parameters are used to set up the drive for operation with a PG option card. Set parameters as needed. Instructions on how to set parameters can be found in the instruction manual for the drive the PG option card is connected to. Table 7 Related Parameters Connector No. Parameter Description CN5-B CN5-C F1-01 Sets the pulses to be read from the pulse PG 1 Pulse Setting <1> generator. Sets the stopping method when the PG becomes disconnected (PGo). 0: Ramp to stop (decelerates at time set to C1- PG Feedback Loss 02) F1-02 (PGo) Operation 1: Coast to stop Selection 2: Fast Stop (decelerates at the time set to C1-09) 3: Continue running F1-03 F1-04 PG Overspeed (os) Operation Selection PG Deviation (dev) Operation Selection F1-05 PG 1 Rotation F1-06 PG 1 Ratio for PG Pulse Monitor Sets the stopping method when overspeed is detected. 0: Ramp to stop (decelerates at time set to C1-02) 1: Coast to stop 2: Fast Stop (decelerates at the time set to C1-09) 3: Continue running 0: Ramp to stop (decelerates at time set to C1-02) 1: Coast to stop 2: Fast Stop (decelerates at the time set to C1-09) 3: Continue running 0: Forward = A pulse leads 1: Forward = B pulse leads Sets the division ratio for the pulses output from the PG encoder. Set as a three digit number where x is the first digit, y is the second digit, and z the third: (1 + x) Ratio = yz When only the A pulse is read, this ratio is 1 disabled and pulses are set as to Setting Range 0 to Default to to to 3 3 0, to YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
21 5 Related Parameters No. F1-08 PG Overspeed (os) Level Overspeed (os) F1-09 Detection Time Excessive Speed Deviation F1-10 Detection (dev) Level Excessive Speed Deviation F1-11 Detection (DEv) Time F1-12 PG 1 Gear Teeth 1 <3> F1-13 <3> F1-14 Parameter PG 1 Gear Teeth 2 PG Disconnect (PGo) Detection Time Reverse Rotation detection for PG 1 (dv3) Reverse Rotation detection for PG 1 (dv4) PG 1 Option Card Function Connector Description CN5-B CN5-C Sets the level for detecting overspeed (os). Set as a percentage of the maximum output frequency. Sets the time required for the motor to exceed the the level set in F1-08 to trigger a fault. Sets the degree of speed deviation to trigger a dev fault. Set as a percentage of the maximum output frequency. Sets the time required a speed deviation situation to trigger a fault. Number of gear teeth between the PG and motor. Pulses 60 F1-13 (load side) F1-01 F1-12 (motor side) A gear ratio of 1 will be used if any of these parameters is set to 0. Sets the time in seconds for PG disconnect to be detected. 0: Disabled F1-18 n: Number of times a dv3 situation must be detected to trigger a fault. 0: Disabled F1-19 n: Number of times a dv4 situation must be detected to trigger a fault. F1-21 0: A pulse detection 1: AB pulse detection Selects the connector for the PG option card F1-30 Motor 2 PG Card connected to motor 2. Connector 0: CN5-C 1: CN5-B F1-31 Sets the pulses to be read from the pulse PG 2 Pulse Setting <1> generator. F1-32 PG 2 Rotation 0: Forward = A pulse leads 1: Forward = B pulse leads Setting Range Default 0 to to 2.0 <2> 0 to to to to to to , to to , 1 0 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 21
22 5 Related Parameters No. F1-33 <3> F1-34 <3> F1-35 F1-37 Parameter PG 2 Gear Teeth 1 PG 2 Gear Teeth 2 PG 2 Division Ratio for Pulse Monitor PG 2 Option Card Function Connector CN5-B CN5-C Description Number of gear teeth between the PG and motor.. Pulses 60 F1-33 (load side) F1-31 F1-34 (motor side) A gear ratio of 1 will be used if any of these parameters is set to 0. Sets the division ratio for the pulses output from the PG encoder. Set as a three digit number where x is the first digit, y is the second digit, and z the third: (1 + x) Ratio = yz When only the A pulse is read, this ratio is 1 disabled and pulses are set as to : A pulse detection 1: AB pulse detection Setting Range 0 to 1000 Default 0 1 to , 1 0 <1> The number of output pulses for the PG can be calculated as follows: Motor speed at maximum frequency output (min f (Hz) -1 ) PG 60 <2> Value changes according to the control mode selection in A1-02. <3> Enabled only when using the V/f with PG control mode. PG rating (p/rev) 22 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
23 6 Troubleshooting 6 Troubleshooting Error Codes Displayed on the Drive Operator The table below lists the various fault codes related to the option card and pulse generator. Further detail on various faults can be found in the instruction manual for the drive. Make sure the PG cable is properly connected. Check the cables between the PG and the option card. Make sure the option card is properly installed to the drive. Table 8 Fault Display Digital Operator Display Fault Name Speed Deviation (for Control Mode with PG) dev The deviation between the speed reference and speed feedback is greater than the setting in F1-10 for longer than the time set to F1-11. Cause Possible Solution Load is too heavy. Reduce the load. Acceleration and deceleration times are set too short. Increase the acceleration and deceleration times (C1-01 through C1-08). The load is locked up. Check the machine. Parameters are not set appropriately. Check the settings of parameters F1-10 and F1-11. Motor brake engaged. Ensure the motor brake releases properly. Digital Operator Display Fault Name dv1 Z-phase Pulse Fall Detection The motor turned one full rotation without the Z pulse being detected. Cause Possible Solution Make sure the PG encoder is properly connected and shielded line is PG encoder is not connected, not wired properly, or is damaged. properly grounded. If the problem continues after cycling power, then replace either the PG option card or the PG encoder itself. Digital Operator Display Fault Name Z-phase Noise Fault Detection dv2 The Z pulse is out of phase by more than 5 degrees for the number of times specified in parameter F1-17. Cause Possible Solution Noise interference along the PG cable. Separate the PG cable lines from the source of the noise (very possibly drive output wiring). PG cable is not wired properly. Rewire the PG encoder and maker sure all lines including shielded line are properly connected. YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 23
24 6 Troubleshooting PG option card or the PG encoder is damaged. Digital Operator Display Cause dv3 The Z-pulse offset is not set properly to E5-11. An external force on the load side has caused the motor to move. Noise interference along the PG cable affecting the A or B pulse. PG encoder is disconnected, not wired properly, or the PG option card or PG itself is damaged. Rotational direction for the PG encoder set to F1-05 is the opposite of the order of the motor lines. Digital Operator Display Cause dv4 The Z-pulse offset is not set properly to E5-11. Noise interference along the PG cable affecting the A or B pulse. PG encoder is disconnected, not wired properly, or the PG option card or PG itself is damaged. If the problem continues after cycling power, then replace either the PG option card or the PG encoder itself. Fault Name Inversion Detection The torque reference and acceleration are in opposite directions from one another (one is in reverse and the other is forward) while at the same time the speed reference and actual motor speed differ by over 30% for the number of pulses set to F1-18. Possible Solution Set the value for Δθ to E5-11 as specified on the motor nameplate. Replacing the PG encoder or changing the application so that the motor rotates in reverse instead requires readjustment of the Z-pulse offset. Make sure the motor is rotating in the right direction. Look for any problems on the load side that might be causing the motor to rotate in the opposite direction. Rewire the PG encoder and make sure all lines including shielded line are properly connected. Make sure motor lines for each phase (U, V, W) are connected properly. Fault Name Inversion Prevention Detection Pulses indicate that the motor is rotating in the opposite direction of the speed reference. Set the number of pulses to trigger inverse detection to F1-19. Note: Disable inverse detection in applications where the motor may rotate in the opposite direction of the speed reference. Setting F1-19 to 0 disables this feature. Possible Solution Set the value for Δθ to E5-11 as specified on the motor nameplate. If the problem continues after cycling power, then replace either the PG option card or the PG encoder itself. Replacing the PG encoder or changing the application so that the motor rotates in reverse instead requires readjustment of the Z-pulse offset. Make sure the motor is rotating in the right direction. Look for any problems on the load side that might be causing the motor to rotate in the opposite direction. Rewire the PG encoder and maker sure all lines including shielded line are properly connected. If the problem continues after cycling power, then replace either the PG option card or the PG encoder itself. 24 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
25 6 Troubleshooting Digital Operator Display Cause ofa00 Non-compatible option card connected to port CN5-A. Digital Operator Display ofb00 Cause Non-compatible option card connected to port CN5-B. Digital Operator Display ofb01 Cause Option card at port CN5-B was changed during run. Digital Operator Display ofc01 Cause Option card at port CN5-C was changed during run. Digital Operator Display ope06 Cause A control mode has been selected that requires a PG option card to be installed, but no PG encoder is installed (A1-02 = 1, 3, or 7). Digital Operator Display Cause Overshoot is occurring. os Incorrect speed feedback scaling if terminal RP is used as speed feedback input in V/f control Fault Name Non-Compatible Option Card at CN5-A Possible Solution Use only compatible option cards. See note <1>. Fault Name Non-Compatible Option Card at CN5-B Possible Solution Use only compatible option cards. See note <1>. Fault Name Option Card Connection Error at CN5-B Possible Solution Switch the power off and reconnect the option card. Fault Name Option Card Connection Error at CN5-C Possible Solution Switch the power off and reconnect the option card. Fault Name Control Method Selection Error Correct the setting for the control method. Possible Solutions Connect a PG option card. Correct the value set to A1-02. Fault Name Overspeed The motor speed feedback exceeded the F1-08 setting. Possible Solutions Increase the settings for C5-01 (Speed Control Proportional Gain 1) and reduce C5-02 (Speed Control Integral Time 1). If using a Closed Loop Vector mode enable Feed Forward Control and perform Inertia Auto-Tuning. Set H6-02 to value of the speed feedback signal frequency when the motor runs at the maximum speed. Adjust the input signal using parameters H6-03 through H6-05. YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 25
26 6 Troubleshooting Incorrect PG pulse number has been set Inappropriate parameter settings. Digital Operator Display PGo Cause PG cable is disconnected. PG cable wiring is wrong. PG encoder does not have enough power. Brake is holding the motor. Check and correct parameter F1-01. Check the setting for the overspeed detection level and the overspeed detection time (F1-08 and F1-09). Fault Name PG Disconnect Detected when no PG pulses received for a time longer than setting in F1-14. Possible Solutions Reconnect the cable. Correct the wiring. Make sure the correct power supply is properly connected to the PG encoder. Ensure the brake releases properly <1> Depending the type of option card, only a certain number of cards may be connected at the same time. Refer to table below. More details can be found in the option card section of the drive instruction manual. Table 9 Option Card Installation Option Card Connector Number of Cards Possible SI-C3, SI-N3, SI-P3, SI-S3, AI-A3, DI-A3 <2> CN5-A 1 PG-B3, PG-X3 CN5-B, C 2 <3> DO-A3, AO-A3 CN5-A, B, C 1 <2> The AI-A3 and DI-A3 option can also be installed to option ports CN5-B and CN5-C, but are then used for monitoring purposes only. Input levels are then displayed in U1-17, U1-21 to U1-23. Here, the option cards cannot be used to set the frequency reference or replace the drive analog input with higher resolution inputs. <3> If only one PG option card is connected to the drive, use the CN5-C connector. If two PG option cards are connected, use both CN5-B and CN5-C. 26 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
27 7 Specifications & Warranty Information 7 Specifications & Warranty Information Specifications Table 10 Option Card Specifications Option Card Compatible Pulse Generators PG Wiring Length PG Power Supply Compatible Control Modes Maximum Input Frequency Pulse Monitor Output PG Disconnect Detection Ambient Temperature Humidity Storage Temperature Area of Use Altitude PG-B3 Complementary, Open-collector Single track (A pulse), 2 track (A, B pulse) or 3 track (A, B, Z pulse) H level: 8 to 12 V L level: 2.0 V max. Complementary: 100 m max. Open-collector: 50 m max. Output voltage: 12 V ± 5% Max. Output Current: 200 ma V/f with PG, Closed Loop Vector, Closed Loop Vector for PM motors 50 khz Monitor for A, B, and Z pulse output: 24 V max, 30 ma Open-collector output Software detection 10 C to 50 C 95% RH or less with no condensation 20 C to 60 C allowed for short-term transport of the product Indoor (free of corrosive gas, airborne particles, etc.) 1000 m or less YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual 27
28 7 Specifications & Warranty Information Revision History The revision dates and numbers of the revised manuals are given on the bottom of the back cover. MANUAL NO. TOBP C A Published in Japan July Date of publication Date of original publication Date of Publication Rev. No Section July 2008 First edition Revised Content 28 YASKAWA ELECTRIC TOBP C A YASKAWA AC Drive-Option Card PG-B3 Installation Manual
29 YASKAWA AC Drive-Option Card Complementary Type PG Installation Manual IRUMA BUSINESS CENTER (SOLUTION CENTER) 480, Kamifujisawa, Iruma, Saitama , Japan Phone Fax YASKAWA ELECTRIC AMERICA, INC Norman Drive South, Waukegan, IL 60085, U.S.A. Phone Fax YASKAWA ELETRICO DO BRASIL LTDA. Avenida Fagundes Filho, 620 Sao Paulo-SP CEP , Brazil Phone Fax YASKAWA ELECTRIC EUROPE GmbH Hauptstraβe 185, Eschborn, Germany Phone Fax YASKAWA ELECTRIC UK LTD. 1 Hunt Hill Orchardton Woods Cumbernauld, G68 9LF, United Kingdom Phone Fax YASKAWA ELECTRIC KOREA CORPORATION 7F, Doore Bldg. 24, Yeoido-dong, Youngdungpo-Ku, Seoul , Korea Phone Fax YASKAWA ELECTRIC (SINGAPORE) PTE. LTD. 151 Lorong Chuan, #04-01, New Tech Park , Singapore Phone Fax YASKAWA ELECTRIC (SHANGHAI) CO., LTD. No.18 Xizang Zhong Road. Room , Harbour Ring Plaza Shanghai , China Phone Fax YASKAWA ELECTRIC (SHANGHAI) CO., LTD. BEIJING OFFICE Room 1011A, Tower W3 Oriental Plaza, No.1 East Chang An Ave., Dong Cheng District, Beijing , China Phone Fax YASKAWA ELECTRIC TAIWAN CORPORATION 9F, 16, Nanking E. Rd., Sec. 3, Taipei, Taiwan Phone Fax YASKAWA ELECTRIC CORPORATION YASKAWA In the event that the end user of this product is to be the military and said product is to be employed in any weapons systems or the manufacture thereof, the export will fall under the relevant regulations as stipulated in the Foreign Exchange and Foreign Trade Regulations. Therefore, be sure to follow all procedures and submit all relevant documentation according to any and all rules, regulations and laws that may apply. Specifications are subject to change without notice for ongoing product modifications and improvements YASKAWA ELECTRIC CORPORATION. All rights reserved. MANUAL NO. TOBP C A Published in Japan July
Installation Manual Type AO-A3
YASKAWA AC Drive-Option Card Analog Monitor Installation Manual Type AO-A3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
Installation Manual Type AI-A3
YASKAWA AC Drive-Option Card Analog Input Installation Manual Type AI-A3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
Installation Manual Type PG-X3
YASKAWA AC Drive-Option Card Line Driver Type PG Installation Manual Type PG-X3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
Installation Manual Type DO-A3
YASKAWA AC Drive-Option Card Digital Output Installation Manual Type DO-A3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
YASKAWA AC Drive-J1000 Option. RS-232C Interface. Technical Manual Type SI-232/J, SI-232/JC RS-232C SI-232/J, SI-232/JC J1000
YASKAWA AC Drive-J1000 Option RS-232C Interface Technical Manual Type SI-232/J, SI-232/JC To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
Analog Monitor Installation Manual
Analog Monitor Installation Manual Part Number: 144-23919 Copyright 2011 Magnetek 1. Preface and Safety Magnetek manufactures products used as components in a wide variety of industrial systems and equipment.
Analog Input Installation Manual
Analog Input Installation Manual August 2011 Part Number: 144-23917 Copyright 2011 Magnetek 1. Preface and Safety Magnetek manufactures products used as components in a wide variety of industrial systems
Installation Manual Type AO-A3
YASKAWA AC Drive 1000-Series Option Analog Monitor Installation Manual Type AO-A3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
Installation Manual Type AI-A3
YASKAWA AC Drive 1000-Series Option Analog Input Installation Manual Type AI-A3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
YASKAWA AC Drive 1000-Series Option Complementary Type PG Installation Manual
YASKAWA AC Drive 1000-Series Option Complementary Type PG Installation Manual Type: PG-B3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
ERN1387. Installation Manual. YASKAWA AC Drive 1000-Series Option Motor Encoder Feedback HEIDENHAIN ERN1387 Interface
YASKAWA AC Drive 1000-Series Option Motor Encoder Feedback HEIDENHAIN ERN1387 Interface Installation Manual Type PG-E3 To properly use the product, read this manual thoroughly and retain for easy reference,
YASKAWA AC Drive-J1000 Option RS-232C Interface. Technical Manual Type SI-232/J, SI-232/JC
YASKAWA AC Drive-J1000 Option RS-232C Interface Technical Manual Type SI-232/J, SI-232/JC To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
LED. Installation Manual Type JVOP-182. YASKAWA AC Drive Option LED Operator JVOP-182
YASKAWA AC Drive Option LED Operator Installation Manual Type JVOP-182 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end
PROFIBUS-DP INTERFACE UNIT INSTRUCTIONS
YASKAWA VS-606 V7 OPTION UNIT PROFIBUS-DP INTERFACE UNIT INSTRUCTIONS MODEL: SI-P1/V7 Upon receipt of the product and prior to initial operation, read these instructions thoroughly and retain them for
YASKAWA AC Drive 1000-Series Option Digital Input
YASKAWA AC Drive 1000-Series Option Digital Input Installation Manual Type DI-A3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
YASKAWA AC Drive 1000-Series Option 24 V Power Supply
YASKAWA AC Drive 1000-Series Option 24 V Power Supply Installation Manual Type: PS-A10L, PS-A10H To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and
YASKAWA AC Drive-1000 Series Option Operator Mounting Kit NEMA Type 4X, IP66 Installation Manual Model No.: UUX or UUX000527
YASKAWA AC Drive-1000 Series Option Operator Mounting Kit NEMA Type 4X, IP66 Installation Manual Model No.: UUX000526 or UUX000527 To properly use the product, read this manual thoroughly and retain for
EnDat, HIPERFACE. Installation Manual. YASKAWA AC Drive Option Motor Encoder Feedback (EnDat, HIPERFACE) Interface. Type: PG-F3
YASKAWA AC Drive Option Motor Encoder Feedback (EnDat, HIPERFACE) Interface Installation Manual Type: PG-F3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection,
YASKAWA 1000-Series Option. 24 V Power Supply
YASKAWA 1000-Series Option 24 V Power Supply Installation Manual Type: PS-A10LB, PS-A10HB To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
DeviceNet. DeviceNet. Installation Manual Type SI-N3. YASKAWA AC Drive-Option Card SI-N3
YASKAWA AC Drive-Option Card DeviceNet Installation Manual Type SI-N3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end
YASKAWA AC Drive 1000-Series Option EtherNet/IP. Technical Manual
YASKAWA AC Drive 1000-Series Option EtherNet/IP Technical Manual Type: SI-EN3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
YASKAWA 1000-Series Option LED Operator
YASKAWA 1000-Series Option LED Operator Installation Manual Type: JVOP-182 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
Installation Manual. YASKAWA AC Drive-V1000 Option EtherNet/IP. Type SI-EN3/V
YASKAWA AC Drive-V1000 Option EtherNet/IP Installation Manual Type SI-EN3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
PROFIBUS-DP. Installation Manual. YASKAWA AC Drive Option PROFIBUS-DP
YASKAWA AC Drive Option PROFIBUS-DP Installation Manual Type: SI-P3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user
EtherNet/IP. EtherNet/IP. Installation Manual. YASKAWA AC Drive Option. Type: SI-EN3
YASKAWA AC Drive Option EtherNet/IP Installation Manual Type: SI-EN3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end
YASKAWA AC Drive Option PROFIBUS-DP. Technical Manual
YASKAWA AC Drive Option PROFIBUS-DP Technical Manual Type: SI-P3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user
Installation Manual Type SI-P3/V
YASKAWA AC Drive-V1000 Option PROFIBUS-DP Installation Manual Type SI-P3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
VS-616PC5/P5 Option Instruction Manual
VS-66PC5/P5 Option Instruction Manual Isolated 4-20mA Output Monitor Card PRECAUTIONS! DANGER. Read this instruction manual in its entirety before installing the Isolated Monitor Card or operating the
YASKAWA AC Drive Option EtherNet/IP. Technical Manual
YASKAWA AC Drive Option EtherNet/IP Technical Manual Type: SI-EN3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user
over time. Improper wiring practices could result in drive malfunction due to loose terminal connections. Control Circuit Terminal Block Functions Dri
Figure 3.14 Main speed frequency reference. Multi-function programmable Safety input Forward run/stop Reverse run/stop External fault Fault reset Multi-step speed 1 main/aux switch Multi-step speed 2 Jog
Technical Manual Type SI-C3
YASKAWA AC Drive-Option Card CC-Link Technical Manual Type SI-C3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user
Technical Manual Type SI-N3
YASKAWA AC Drive-Option Card DeviceNet Technical Manual Type SI-N3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user
Installation Manual Type SI-EN3
YASKAWA AC Drive 1000-Series Option EtherNet/IP Installation Manual Type SI-EN3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
Technical Manual. YASKAWA AC Drive-Option Card MECHATROLINK-II. Type: SI-T3
YASKAWA AC Drive-Option Card MECHATROLINK-II Technical Manual Type: SI-T3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
YASKAWA AC Drive 1000-Series Option EtherNet/IP. Technical Manual
TM YASKAWA AC Drive 1000-Series Option EtherNet/IP Technical Manual Type: SI-EN3D To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
YASKAWA AC Drive 1000-Series Option
YASKAWA AC Drive 1000-Series Option Modbus TCP/IP Installation Manual Type: SI-EM3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
DeviceNet. DeviceNet. Installation Manual. YASKAWA AC Drive-V1000 Option V1000. Type SI-N3/V
YASKAWA AC Drive-V1000 Option DeviceNet Installation Manual Type SI-N3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
Installation Manual Type SI-N3/V
YASKAWA AC Drive-V1000 Option DeviceNet Installation Manual Type SI-N3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
Installation Manual. YASKAWA AC Drive 1000-Series Option Modbus TCP/IP. Type SI-EM3
YASKAWA AC Drive 1000-Series Option Modbus TCP/IP Installation Manual Type SI-EM3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
Technical Manual. YASKAWA AC Drive 1000-Series Option Modbus TCP/IP. Type: SI-EM3
MANUAL NO. SIEP C730600 57A YASKAWA AC Drive 1000-Series Option Modbus TCP/IP Technical Manual Type: SI-EM3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection,
YASKAWA AC Drive-V1000 Option PROFIBUS-DP. Technical Manual
YASKAWA AC Drive-V1000 Option PROFIBUS-DP Technical Manual Type: SI-P3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
YASKAWA AC Drive Option DeviceNet. Technical Manual
YASKAWA Option DeviceNet Technical Manual Type SI-N3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user receives this
Installation & Technical Manual
YASKAWA AC Drive - 1000-Series Option Metasys N2 & APOGEE FLN P1 Installation & Technical Manual Type: SI-J3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection,
2012 YASKAWA ELECTRIC CORPORATION
Copyright 2012 YASKAWA ELECTRIC CORPORATION All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, electronic,
YASKAWA AC Drive 1000-Series Option PROFINET. Installation Manual
TM YASKAWA AC Drive 1000-Series Option PROFINET Installation Manual Type: SI-EP3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
YASKAWA AC Drive 1000-Series Option
YASKAWA AC Drive 1000-Series Option DeviceNet Installation Manual Type: SI-N3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
YASKAWA AC Drive 1000-Series Option LCD Operator
YASKAWA AC Drive 1000-Series Option LCD Operator Installation Manual Type JVOP-180 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
YASKAWA AC Drive 1000-Series Option EtherNet/IP. Installation Manual
TM YASKAWA AC Drive 1000-Series Option EtherNet/IP Installation Manual Type: SI-EN3D To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
FR-A8AR INSTRUCTION MANUAL
INVERTER Plug-in option FR-A8AR INSTRUCTION MANUAL Relay output function PRE-OPERATION INSTRUCTIONS INSTALLATION AND WIRING RELAY OUTPUT 1 2 3 Thank you for choosing this Mitsubishi inverter plug-in option.
MECHATROLINK-III MECHATROLINK-III
YASKAWA AC Drive- Option MECHATROLINK-III Installation Manual Type: SI-ET3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
Ethernet/IP Single and Dual-Port
YASKAWA Z1000 Bypass Option Ethernet/IP Single and Dual-Port Technical Manual Type: SI-EN3/SI-EN3D Applicable Products : Z1B1- To properly use the product, read this manual thoroughly and retain for easy
YASKAWA AC Drive Z1000
YASKAWA AC Drive Z1000 AC Drive Bypass for HVAC Fans and Pumps Manual Supplement Bypass controller firmware version: VST800298 Bypass controller monitor UB-18 displays the software version of the Z1000
YASKAWA AC Drive 1000-Series Option
YASKAWA AC Drive 1000-Series Option PROFIBUS-DP Installation Manual Type: SI-P3/V, SI-P3/T To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
LCD. Installation Manual Type JVOP-180. YASKAWA AC Drive-Option LCD Operator JVOP-180
YASKAWA AC Drive-Option LCD Operator Installation Manual Type JVOP-180 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end
YASKAWA AC Drive J1000
YASKAWA AC Drive J1000 Compact V/f Control Drive Technical Manual Type: CIMR-JC Model: 200 V Class, Single-Phase Input: 0.1 to 2.2 kw 200 V Class, Three-Phase Input: 0.1 to 5.5 kw 400 V Class, Three-Phase
YASKAWA AC Drive-J1000
YASKAWA AC Drive-J1000 Compact V/f Control Drive Technical Manual Type: CIMR-JU Models: 200 V Class, Three-Phase Input: 0.1 to 5.5 kw 200 V Class, Single-Phase Input: 0.1 to 2.2 kw 400 V Class, Three-Phase
2 YASKAWA ELECTRIC SIEP C A V1000 Option Modbus TCP/IP Technical Manual
Copyright 2012 YASKAWA ELECTRIC CORPORATION All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, electronic,
INVERTER INSTRUCTION MANUAL. Relay output function. Plug-in option FR-A7AR PRE-OPERATION INSTRUCTIONS INSTALLATION AND WIRING RELAY OUTPUT
INVERTER Plug-in option FR-A7AR INSTRUCTION MANUAL Relay output function PRE-OPERATION INSTRUCTIONS INSTALLATION AND WIRING RELAY OUTPUT 1 2 3 Thank you for choosing this Mitsubishi Inverter plug-in option.
OPC-VG1-PG / PGo. PG Interface Card for FRENIC-VG. Instruction Manual
Instruction Manual PG Interface Card for FRENIC-VG OPC-VG1-PG / PGo Thank you for purchasing our PG interface card designed for the high-performance, vector control FRENIC-VG series of inverters. - Improper
YASKAWA AC Drive J1000
YASKAWA AC Drive J1000 Compact V/f Control Drive Technical Manual Type: CIMR-JU Models: 200 V Class, Three-Phase Input: 0.1 to 5.5 kw 200 V Class, Single-Phase Input: 0.1 to 2.2 kw 400 V Class, Three-Phase
IO-AO6X I/O Expansion Module 6 Isolated Analog Outputs
IO-AO6X I/O Expansion Module 6 Isolated Analog Outputs The IO-AO6X is an I/O Expansion Module that can be used in conjunction with specific Unitronics OPLC controllers. The module offers 6 12-bit isolated
YASKAWA AC Drive-J1000
YASKAWA AC Drive-J1000 Compact V/f Control Drive Quick Start Guide Type: CIMR-JU Models: 200 V Class, Three-Phase Input: 0.1 to 5.5 kw 200 V Class, Single-Phase Input: 0.1 to 2.2 kw 400 V Class, Three-Phase
LONWORKS Option Card CM048
LONWORKS Option Card CM48! Unpack the LONWORKS Option Kit and verify that all components are present and undamaged. Part LONWORKS Option Board (UUX258) 1 LONWORKS Data Diskette 1 Installation Guide (IG.AFD.2)
Varispeed SERIES OPTION CARD DeviceNet COMMUNICATION INTERFACE CARD USER'S MANUAL Model: SI-N1
YASKAWA Varispeed SERIES OPTION CARD DeviceNet COMMUNICATION INTERFACE CARD USER'S MANUAL Model: SI-N1 YASKAWA MANUAL NO. SIBP C730600 01B Copyright 2004 YASKAWA ELECTRIC CORPORATION All rights reserved.
Technical Manual Type SI-P3
YASKAWA AC Drive 1000-Series Option PROFIBUS-DP Technical Manual Type SI-P3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
YASKAWA AC Drive-J1000 Compact V/f Control Drive Technical Manual
YASKAWA AC Drive-J1000 Compact V/f Control Drive Technical Manual Type: CIMR-JU Models: 200 V Class, Three-Phase Input: 0.1 to 5.5 kw 200 V Class, Single-Phase Input: 0.1 to 2.2 kw 400 V Class, Three-Phase
YASKAWA AC Drive Option PROFINET. Technical Manual
YASKAWA AC Drive Option PROFINET Technical Manual Type: SI-EP3 To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user receives
PROFINET. Installation Manual. YASKAWA AC Drive-V1000 Option. Type SI-EP3/V
YASKAWA AC Drive-V1000 Option PROFINET Installation Manual Type SI-EP3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
YASKAWA AC Drive J1000
YASKAWA AC Drive J1000 Compact V/f Control Drive Installation & Start-Up Manual Type: CIMR-JA, CIMR-JT Models: 200 V Class, Three-Phase Input: 0.1 to 5.5 kw 200 V Class, Single-Phase Input: 0.1 to 2.2
V E1B Snap-in I/O Module
V200-18-E1B Snap-in I/O Module The V200-18-E1B plugs directly into the back of compatible Unitronics OPLCs, creating a selfcontained PLC unit with a local I/O configuration. Features 16 isolated digital
YASKAWA AC Drive 1000-Series Option PROFIBUS-DP
YASKAWA AC Drive 1000-Series Option PROFIBUS-DP Installation Manual Type: SI-P3/V, SI-P3/T To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
YASKAWA AC Drive-V1000 Option. Modbus TCP/IP. Installation Manual
YASKAWA AC Drive- Option Modbus TCP/IP Installation Manual Type: SI-EM3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the
YASKAWA AC Drive-V1000 Option EtherNet/IP
YASKAWA AC Drive-V1000 Option EtherNet/IP Installation Manual Type: SI-EN3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure
V1000 Series AC Drive
Installation & Start-Up Manual V1000 Series AC Drive Receiving Mechanical Installation Electrical Installation Start-Up Programming and Operation Troubleshooting Periodic Inspection and Maintenance Options
H Manual Stretch Wrap Machine uline.com FILM ROLL CAPACITY TECHNICAL DATA ELECTRICAL SPECIFICATIONS TURNTABLE SPECIFICATIONS
H-2304 Manual Stretch Wrap Machine 1-800-295-5510 uline.com SYSTEM SpecificationS IMPORTANT! Read this manual thoroughly and familiarize yourself with ALL controls and operating features. Keep this manual
V E1B Snap-in I/O Module
V200-18-E1B Snap-in I/O Module The V200-18-E1B plugs directly into the back of compatible Unitronics OPLCs, creating a selfcontained PLC unit with a local I/O configuration. Features 16 isolated digital
LiquiFlo AC General Purpose (Volts/Hertz) and Vector Duty Drive Software Start-Up and Reference Manual Version 6.4
LiquiFlo AC General Purpose (Volts/Hertz) and Vector Duty Drive Software Start-Up and Reference Manual Version 6.4 Instruction Manual D2-3410-7 The information in this manual is subject to change without
Operating instructions. Standstill monitor A / / 2011
Operating instructions Standstill monitor A300 UK 1 2 3 4 5 6 7 8 7390337 / 01 02 / 2011 1 2 3 4 5 6 7 8 switchpoint min max pulse/min power Made in Germany ifm electronic gmbh D 45127 Essen func. I II
Line reactors SINAMICS. SINAMICS G130 Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation
Safety information 1 General 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions Control version V4.7 04/2014 A5E00331462A Legal
GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000
GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000 Instruction Manual D2-3390-2 The information in this manual is subject to change without notice. Throughout this manual, the
24/48/120 VAC Interface Card Instruction Manual
24/48/120 VAC Interface Card Instruction Manual Distributed by Ergonomic Partners Sales@ErgonomicPartners.com www.ergonomicpartners.com Tel: (314) 884-8884 April 2012 Part Number: -R2 Copyright 2012 Magnetek
Technical Manual SMART TRAC PS Card
Technical Manual SMART TRAC PS Card Contents Important Safety and Warranty Information 1 Warnings, Cautions and Notes...1 General Safety Precautions - Warnings...2 Important Warranty Information...2 Smart
GV3000/SE 230 VAC 1-20 HP General Purpose (Volts/Hertz) and Vector Duty Drive Software Start-Up and Reference Manual Version 6.04
GV3000/SE 230 VAC 1-20 HP General Purpose (Volts/Hertz) and Vector Duty Drive Software Start-Up and Reference Manual Version 6.04 Instruction Manual D2-3387-4 The information in this manual is subject
TRC-190 User s Manual
User s Manual Edition 3.2, May 2017 www.moxa.com/product 2017 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used only
V E2B Snap-in I/O Module
V200-18-E2B Snap-in I/O Module The V200-18-E2B plugs directly into the back of compatible Unitronics OPLCs, creating a selfcontained PLC unit with a local I/O configuration. Features 16 isolated digital
SUN2000P-375 W Smart PV Optimizer. User Manual. Issue 01. Date HUAWEI TECHNOLOGIES CO., LTD.
Issue 01 Date 2017-08-01 HUAWEI TECHNOLOGIES CO., LTD. 2017. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of
SMVector Additional I/O Module Installation and Operation Manual
SMVector Additional I/O Module Installation and Operation Manual About These Instructions This documentation applies to the optional Additional I/O module for the SMVector inverter and should be used in
YASKAWA AC Drive 1000-Series Option. Modbus TCP/IP. Installation Manual
YASKAWA AC Drive 1000-Series Option Modbus TCP/IP Installation Manual Type: SI-EM3D To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance.
Hybrid AC Driver [GCNC-1110]
Page 1 Installation Manual and Datasheet Page 2 Key Features Smooth and quiet operation at all speeds and extremely low motor heating Industrial grade performance for an alternating current servo motor
Technical Manual. Inverter HF-520 Option CC-Link. Manual
Inverter HF-520 Option CC-Link Technical Manual Type SI-C3/V-H NOTICE 1. Make sure that this technical manual is delivered to the end user of inverter unit. 2. Read this manual before installing or operating
Operating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
Digital ac/dc (24V) Input Module
Installation Instructions Digital ac/dc (24V) Input Module Catalog Number 1771-IND, Series C Topic Page Important User Information 2 Before You Begin 3 Power Requirements 3 Prevent Electrostatic Discharge
Operating instructions. Speed monitor D / / 2014
Operating instructions Speed monitor D200 80005257 / 00 05 / 2014 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5 2.2 Target group...5
8902/E1 Sin/Cos Speed Feedback Option
8902/E1 Sin/Cos Speed Feedback Option Technical Manual HA469252U001 Issue 2 Compatible with Version 1.x Software Copyright 2007 Parker SSD Drives, a division of Parker Hannifin Ltd. All rights strictly
YASKAWA AC Drive-V1000 Option CANopen. Technical Manual
YASKAWA AC Drive-V1000 Option CANopen Technical Manual Type SI-S3/V To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user
The following conventions are used to indicate precautions in this manual.
Safety Information Read this instruction manual and the related documents thoroughly before installation, operation, maintenance or inspection of this product. Make sure you understand product information,all
IO-DI8-TO8, IO-DI8-TO8-L I/O Expansion Modules 8 Inputs, 8 Outputs
IO-DI8-TO8, IO-DI8-TO8-L I/O Expansion Modules 8 Inputs, 8 Outputs The IO-DI8-TO8 and IO-DI8-TO8-L are I/O expansion modules that can be used in conjunction with specific Unitronics OPLC controllers. The
V E2B Snap-in I/O Module
i4 Automation Ltd - 01480 395256 V200-18-E2B Snap-in I/O Module The V200-18-E2B plugs directly into the back of compatible Unitronics OPLCs, creating a selfcontained PLC unit with a local I/O configuration.
Line reactors SINAMICS. SINAMICS G120P Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation 4
Safety information 1 General 2 SINAMICS SINAMICS G120P Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions Control version V4.6 11/2013 A5E32845290B AA
YASKAWA AC Drive A1000 Option. Technical Manual
YASKAWA AC Drive A1000 Option Technical Manual Type: SI-ES3 for A1000 Series To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure