VN310 Hardware Integration
|
|
- Lester Lester
- 5 years ago
- Views:
Transcription
1 VN310 Hardware Integration Application Note Revision 1.0 December 18,
2 Contents 1. INTRODUCTION PIN-OUT AND INTERFACE SUMMARY INTERFACING WITH VN310-I FOR ISA100.11A APPLICATIONS VN310-I HARDWARE INTERFACING VIA UART VN310-I HARDWARE INTERFACING VIA SPI INTERFACING WITH VN310-H FOR WIRELESS HART APPLICATIONS VN310-H HARDWARE INTERFACING VIA UART VN310-H HARDWARE INTERFACING VIA SPI VN310-H HARDWARE INTERFACING WITH THE WIRED HART MAINTENANCE PORT CIRCUITRY VN310 KEY SPECIFICATIONS EXTERNAL ANTENNA SPECIFICATIONS AND INSTALLATION REQUIREMENTS VN310 MECHANICAL SPECIFICATIONS VN310 COMPLIANCE WITH RADIO LAWS Page 2 of 15
3 1. Introduction The purpose of this document is to provide the necessary data to achieve hardware integration of the VN310 with a customer s eternal application processor. By definition the VN310 is essentially a radio module, approimately 1.1 W 1.4 L, that is pre-loaded with the Nivis wireless communications stack. The small form factor enables the radio to be used in a variety of applications. There are two variants of the VN310 radio module that are identical from hardware perspective, the only difference being the wireless communications stack firmware loaded: VN310-I pre-loaded with Nivis ISA100.11a stack as factory firmware VN310-H pre-loaded with Nivis Wireless Hart stack as factory firmware. The VN310 module employs two TTL serial ports, UART1 and UART2. The UART1 port is reserved for factory configuration however in the case of VN310-H it is also used to interface with a wired HART modem for the required HART maintenance port. An eternal processing entity can communicate with the VN310 using either a UART interface (UART2) or an SPI interface. 2. Pin-out and Interface Summary The VN310 radio module uses a Freescale 32-bit ARM7 microcontroller as its core. The transmit path utilizes a PA (power amplifier) to increase the power output of the integrated 2.4 GHz, radio transmitter to a maimum output power at the antenna connector of +15 dbm, and with a nominal operating power level of +10 dbm. The transmit power variation vs. temperature is no greater than +/- 3 db over the industrial temperature range of A digital-to-analog converter (DAC) is used to vary the bias voltage on the power amplifier to adjust the radio output power, and also to maintain the optimum output power vs. current consumption. The advantages of a radio module with adjustable power output are the following: Ability to adjust radio output power in steps of 1 dbm, from 0 dbm to +15 dbm, for maimum fleibility and range. Energy consumption can be reduced by using lower radio output power setting, while communication range can be increased by using higher radio output power. Provides greater power level consistency, for systems where symmetrical links are more critical. The normalized radio output power means that the radio will transmit with the same outout power on all radio Page 3 of 15
4 channels and its communications range is consistent. Country code (CC) support enables the unit to be configured for different regulatory certification needs, especially locations that require reduced transmit power, such as Europe, Japan, and China. By simply configuring the CC into the VN310, the module self-adjustes so that its radio transmit power is compliant with the country regulations. Once CC set, the application processor can only configure the radio s transmit output power from 0 dbm to the maimum allowed by the CC. Some software protocol stacks such as the Wireless Hart and ISA100.11a standards require a very high stability time base. The VN310 module is by design optimized for such needs by using a temperature compensated (DTCXO) real time clock. The DTCXO s maimum drift is 5 ppm over the entire temperature range of To improve reliability, a separate onboard hardware watchdog timer is used to reset the radio if the core stops communicating with the watchdog for a predefined time interval. UART2_RTS/EXTRTS UART2_CTS/EXTCTS UART2_RX UART2_TX UART1_RTS/HART_MODEM_RTS GND UART1_CTS UART1_RX/HART_MODEM_RX UART1_TX/HART_MODEM_TX RDY_RADIO GND SPI_SCK/CLK SPI_MOSI/MOSI SPI_MISO/MISO SPI_SS/SS GPIO/VN_LED RESET GND VIN GPIO/VN_LED2 GPIO/HART_MODEM_CD_IC GND WKU_RADIO GPIO/HART_MODEM_PWR GPIO/VN_LED3 BOOT_SWITCH GPIO/HART_MODEM_CD VN_STATUS GND GND Figure 1: VN310 Pin-out and signals direction (top view) Note 1: All pins marked as must be left unconnected. Note 2: To minimize energy consumption, all unused pins should be left unconnected. Page 4 of 15
5 Table 1: VN310 Pin Definitions No. Name Description Type Dir Comments 1 UART2-RTS UART2 Request to Send DIG In UART communication between VN310 and application processor (AP). This signal is active low and is used by the AP to indicate a ready-toreceive state. 2 UART2-CTS UART2 Clear to Send DIG Out UART communication between VN310 and application processor. This signal is active low and is used by VN310 to indicate a want-to-send state. 3 UART2-RXD UART2 Receive Data DIG In UART communication between VN310 and application processor. 4 UART2-TXD UART2 Transmit Data DIG Out UART communication between VN310 and application processor. 5 UART1-RTS UART1 Request to Send DIG I/O Input on VN310-I. Output on VN310-H. 6 GND Ground N/A N/A 7 UART1-CTS UART1 Clear to Send DIG Out Standard UART communication with flow control. Not used on VN310-H. 8 UART1-RXD UART1 Receive Data DIG In Standard UART communication with flow control. 9 UART1-TXD UART1 Transmit Data DIG Out Standard UART communication with flow control. 10 N/A N/A Not Used. Do not connect. 11 N/A N/A Not Used. Do not connect. 12 RDY_RADIO RDY_RADIO DIG Out READY signal used by VN310 to wake up the application processor. This signal is active low and is used by VN310 to indicate a ready-toreceive state. It will be generated as a response to the application CPU WKU signal. 13 N/A N/A Not Used. Do not connect. 14 GND Ground N/A N/A 15 SPI-SCK SPI Clock DIG Out Standard SPI Communication. 16 SPI-MOSI SPI Data Out DIG Out Standard SPI Communication. 17 SPI-MISO SPI Data In DIG In Standard SPI Communication. 18 SPI-SS SPI Slave Select DIG Out Standard SPI Communication. 19 GPIO GPIO/VN_LED1 N/A N/A GPIO used to control VN310 s LED1. Do not connect if not needed. 20 N/A N/A Not Used. Do not connect. 21 VN_STATUS VN_STATUS DIG In VN310 wakeup/status/reset_to_provisioning_default, usually connected to a push-button. Holding this pin low for 2 seconds wakes-up the VN310 and LEDs signaling. On VN310-I, holding this pin low for 10 seconds causes the radio to reset its provisioning information to the factory defaults state and unjoin the network. 22 N/A N/A Not Used. Do not connect. 23 GND Ground N/A N/A 24 N/A N/A Not Used. Do not connect. Page 5 of 15
6 No. Name Description Type Dir Comments 25 N/A N/A Not Used. Do not connect. 26 N/A N/A Not Used. Do not connect. 27 N/A N/A Not Used. Do not connect. 28 N/A N/A Not Used. Do not connect. 29 N/A N/A Not Used. Do not connect. 30 N/A N/A Not Used. Do not connect. 31 GND Ground N/A N/A 32 DIG I/O Not Used. Do not connect. 33 DIG I/O Not Used. Do not connect. 34 DIG I/O Not Used. Do not connect. 35 DIG I/O Not Used. Do not connect. 36 DIG I/O Not Used. Do not connect. 37 DIG I/O Not Used. Do not connect. 38 GPIO GPIO HART_MODEM_CD DIG In GPIO not used in VN310-I. Do not connect. HART_MODEM_CD pin used by VN310-H to detect the carrier (CD) from eternal wired HART maintenance port s modem. This signal is required for lower power consumption. 39 BOOT_SWITCH GPIO BOOT_SWITCH DIG In VN310 s bootloader reads this GPIO s state at startup and decides what firmware image to boot. Usually connected to a switch in multi-boot configuration (VN310-I & VN310-H), or pulled-high for VN310-I configuration, or pulled-low for VN310-H configuration. 40 GPIO GPIO/VN_LED3 DIG Out GPIO used to control VN310 s LED3. Do not connect if not needed. Not used on VN310-H. 41 GPIO GPIO HART_MODEM_PWR DIG Out GPIO not used in VN310-I. Do not connect. HART_MODEM_PWR pin used by VN310-H to power ON/OFF the eternal wired HART maintenance port (energy saving). 42 WKU_RADIO WKU_RADIO DIG In Eternal wake-up signal used by the AP to wake up the VN310 module. This signal is active high and is used by the AP to wake up the VN310 from sleep mode, and to signal the intention to communicate with the VN310. Keeping this line active will block the VN310 from entering low power mode (sleep). 43 GND Ground N/A N/A 44 GPIO GPIO HART_MODEM_CD_IC N/A N/A GPIO not used in VN310-I. Do not connect. HART_MODEM_CD_IC pin used by VN310-H to detect the carrier (CD) from eternal wired HART maintenance port s modem. HART_MODEM_CD_IC is usually a CD signal provided by a SoC HART modem, while the HART_MODEM_CD signal is generated by a lower power consumption circuitry thus allowing powering off the HART Page 6 of 15
7 No. Name Description Type Dir Comments modem during sleep mode. 45 N/A N/A Not Used. Do not connect. 46 GPIO GPIO/VN_LED2 DIG Out GPIO used to control VN310 s LED2. Do not connect if not needed. Not used on VN310-H. 47 N/A N/A Not Used. Do not connect. 48 Vin Supply Voltage N/A In See Note GND Ground N/A N/A 50 RESET RESET pin DIG In Reset pin of the VN310. LOW to reset and HIGH to run. 51 N/A N/A Not Used. Do not connect. 52 N/A N/A Not Used. Do not connect. 53 N/A N/A Not Used. Do not connect. 54 N/A N/A Not Used. Do not connect. 55 N/A N/A Not Used. Do not connect. Note 3: In the default configuration, the radio is powered directly from an eternal power source which should have a range of 3.3 to 10.0 volts for standard operation. The radio has an internal LDO regulator that provides a constant 3.0 volts in order to maintain a narrow output power range and to comply with regulatory requirements. Contact Nivis engineering for more information. 3. Interfacing with VN310-I for ISA100.11a applications An application processor (AP) can communicate with the VN310 radio module using either UART or SPI hardware interfacing. The supported communication protocols between AP and VN310-I are described in the following documents: Full API: _Nivis_ISA100.11a_FULL_API_Integration_Manual.pdf Simple API: _Nivis_ISA100.11a_SIMPLE_ API Integration_Manual.pdf Page 7 of 15
8 3.1 VN310-I hardware interfacing via UART Figure 2: VN310-I hardware interfacing via UART Page 8 of 15
9 3.2 VN310-I hardware interfacing via SPI Figure 3: VN310-I hardware interfacing via SPI Page 9 of 15
10 4. Interfacing with VN310-H for Wireless HART applications An application processor (AP) can communicate with the VN310 radio module using either UART or SPI hardware interfacing. The supported communication protocols between AP and VN310-H are described in the following documents: Full API: _Nivis_WirelessHART_Full_API_Integration_Manual.pdf Simple API: _Nivis_WirelessHART_Simple_API_Integration_Manual.pdf 4.1 VN310-H hardware interfacing via UART Figure 4: VN310-H hardware interfacing via UART Page 10 of 15
11 4.2 VN310-H hardware interfacing via SPI Figure 5: VN310-H hardware interfacing via SPI 4.3 VN310-H hardware interfacing with the Wired HART Maintenance Port circuitry Figure 6: VN310-H hardware interfacing with HART Maintenance Port Page 11 of 15
12 5. VN310 Key Specifications For detailed information please consult the following documents: VN310 Datasheet: Nivis_VersaNode_310_Datasheet.pdf 5.1 Eternal antenna specifications and installation requirements Figure 7: Antenna specifications Antenna Installation requirements The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Page 12 of 15
13 6. VN310 Mechanical Specifications Figure 8: VN310 mechanical dimensions Figure 9: VN310 s RF Shield Page 13 of 15
14 Figure 10: VN310 Additional Drawings Page 14 of 15
15 Figure 11: VN310 Recommended Footprint 7. VN310 compliance with Radio Laws EN v1.7.1 (Europe) FCC ID: SQB-VN R5 (USA) IC ID: 6546A-VN R5 (Canada) MIC (MIC Notice No. 88 Appendi No. 43, Japan) For detailed information please consult Nibis website and the following documents: VN310 Datasheet: Nivis_VersaNode_310_Datasheet.pdf Page 15 of 15
Product Specification
Product Specification Features Amp ed RF, Inc. Description 15mm x 27mm The added class 1 power, +18dBm, of the BT-11, gives this module one of the best ranges in the industry. It s completely pin compatible
More informationProduct Specification
Product Specification 15mm x 27mm Description One of the most capable Bluetooth modules available, the BT-21 Bluetooth OEM Module is designed for maximum flexibility. The BT-21 module includes 14 general
More informationBT 31 Data Sheet. Amp ed RF Technology Inc.
BT 31 Data Sheet Amp ed RF Technology Inc. Product Specification BT31 Features Bluetooth features FCC&Bluetooth licensed radio Bluetooth v3.0 Class 1 radio Range up to 100m LOS 1.5Mbps data throughput
More informationxpico 200 Series Evaluation Kit User Guide
xpico 200 Series Evaluation Kit User Guide This guide describes how to setup the xpico 200 series evaluation kit and provides the information needed to evaluate the included xpico 240 or xpico 250 embedded
More informationBLE Bluetooth Low Energy Modules SBC2112-B. Preliminary Specification. Version 1.0
BLE Bluetooth Low Energy Modules SBC2112-B Preliminary Specification Version 1.0 23-JUN.-2014 Content 1. Description...3 2. Features...3 3. Block Diagram...3 4. Radio Characteristics...4 5. Electrical
More informationBT-22 Product Specification
BT-22 Product Specification Features Amp ed RF, Inc. Description 10.4 mm x 13.5 mm Our micro-sized Bluetooth module is the smallest form factor available providing a complete RF platform. The BT-22 is
More informationReindeer Technologies Pvt Ltd Excellence through Innovation
RDZM-T24FZ 2.4 GHZ IEEE 802.15.4/ZIGBEE RF TRANSCEIVER Datasheet Reindeer Technologies Pvt Ltd Excellence through Innovation S-2, Old No. 15, New No. 31 Rajamannar Street, T Nagar, Chennai 600017 India.
More informationHZX N03 Bluetooth 4.0 Low Energy Module Datasheet
HZX-51822-16N03 Bluetooth 4.0 Low Energy Module Datasheet SHEN ZHEN HUAZHIXIN TECHNOLOGY LTD 2017.7 NAME : Bluetooth 4.0 Low Energy Module MODEL NO. : HZX-51822-16N03 VERSION : V1.0 1.Revision History
More informationPrototyping Module Datasheet
Prototyping Module Datasheet Part Numbers: MPROTO100 rev 002 Zenseio LLC Updated: September 2016 Table of Contents Table of Contents Functional description PROTOTYPING MODULE OVERVIEW FEATURES BLOCK DIAGRAM
More informationMarch 21, BT22 Datasheet. Amp ed RF Technology, Co., Ltd.
March 21, 2011 BT22 Datasheet Amp ed RF Technology, Co., Ltd. BT22 Features Bluetooth features Bluetooth qualified Bluetooth v2.1+edr Class 2 radio Range up to 30m LOS Description 10.4 mm x 13.5 mm Our
More informationELET114A Bluetooth Module DATASHEET. Website:http://www.elinketone.com / 7
Bluetooth Module DATASHEET Website:http://www.elinketone.com 2013 06 09 1 / 7 A. Overview Bluetooth Module is designed by ShenZhen ElinkEtone Technology Company for intelligent wireless transmission, with
More informationUser Guide. Date Apr BlueEva+C11/G2. Stollmann. E + V GmbH. User Guide
Version r02 Date Apr 2009 Author: ta Date saved: 06.04.09 Ref: BlueEva+C11G2_User_Guide_r02.doc Revision: r02 Page 1 of 22 Note This device was developed for the purpose of communication in an office environment.
More informationApproved by: Date CET Initials Name Justification :20:12 NTJ Niels Thybo Johansen
Instruction Selection Guideline Document No.: INS10027 Version: 6 Description: This document introduces the ZW0201, and ZW0301 Single Chip based families, and suggests which module to choose for a given
More informationSH1030 Rev Introduction. Ultra low power DASH7 Arduino Shield Modem. Applications. Description. 868 MHz. Features
SH1030 Rev. 1.2 Applications Wireless sensor network Data acquisition equipment Security systems Industrial monitor and control Internet of things (IoT) Ultra low power DASH7 Arduino Shield Modem 868 MHz
More informationALPW-BLEM103 Datasheet 1.0 Bluetooth Low Energy HCI
ALPW-BLEM103 Datasheet 1.0 Bluetooth Low Energy HCI FEATURES Ready-to-use Bluetooth Low Energy HCI module Ultra Small form factor 12mm x 12mm Ultra Low Power consumption EM Microelectronic Bluetooth Low
More informationRayson Bluetooth Module
Rayson Bluetooth Module Low Energy Smart Module Features Bluetooth standard V4.0 conformity. CSR000/00 chip Programmable general purpose PIO controller : Switch-mode power supply. IC for EEPROM and ICs
More informationESPino - Specifications
ESPino - Specifications Summary Microcontroller ESP8266 (32-bit RISC) WiFi 802.11 (station, access point, P2P) Operating Voltage 3.3V Input Voltage 4.4-15V Digital I/O Pins 9 Analog Input Pins 1 (10-bit
More informationWM1030 Rev Introduction. Ultra low power DASH7 Modem. Applications. Description. 868 / 915 MHz. Features. WIZZILAB Technical datasheet 1/10
WM1030 Rev. 1.2 Applications Wireless sensor network Data acquisition equipment Security systems Industrial monitor and control Internet of things (IoT) Ultra low power DASH7 Modem 868 / 915 MHz 1 Introduction
More informationLM780 Bluetooth Classic Data Module with IC Antenna
Bluetooth Classic Data Module with C Antenna Revised 7/DEC/206 Features Bluetooth v2.0/ v2. specification 26.92mm x 5.20mm x 2.0mm 4 dbm Tx utput Power (Class 2) SMT Side and Bottom Pads for easy production
More informationPmod modules are powered by the host via the interface s power and ground pins.
1300 Henley Court Pullman, WA 99163 509.334.6306 www.store. digilent.com Digilent Pmod Interface Specification 1.2.0 Revised October 5, 2017 1 Introduction The Digilent Pmod interface is used to connect
More informationLM072 Bluetooth 2.0 / EDR Serial Data Module Class 1 BC04, 8MB Flash, Up to 100m
Bluetooth.0 /. + EDR Serial Data Module 0700 0/MAR/0 8.mm mm Features Applications Bluetooth standard v.0 and BT v. + EDR specification Serial Communications SPP firmware supported by default. Medical
More informationDatasheet DFBM-NQ62X-DT0R. A Bluetooth Low Energy System On Chip Module. Proprietary Information and Specifications are Subject to Change
1 Datasheet DFBM-NQ62X-DT0R A Bluetooth Low Energy System On Chip Module. Preliminary Data Sheet Sheet 1 of 18 Aug. 16, 2016 Contents 1. Features... 3 1-1. General... 3 1-2. Bluetooth... 3 2. Model No.
More informationGSM 4 click MIKROE Weight: 33 g
GSM 4 click MIKROE-2388 Weight: 33 g GSM 4 click is a mikrobus add-on board that features the u-blox SARA-G3 series 2.5G GSM/GPRS cellular quad-band module. The SARA-G3 module has a miniature LGA (Land
More informationAi-Thinker. ESP-12S Datasheet. Version V0. Copyright 2018 ESP-12S WIFI MODULE V0. Shenzhen Ai-Thinker Technology Co., Ltd All Rights Reserved
Copyright 2018 Shenzhen Technology Co., Ltd All Rights Reserved ESP-12S Datasheet Version V0 Copyright 2018 Disclaimer and Copyright Notice Information in this document, including URL references, is subject
More informationPmod ESP32 Reference Manual
Pmod ESP32 Reference Manual The Digilent Pmod ESP32 features a radio with support for 802.11 b/g/n Wifi and dualmode Bluetooth. This module is perfect for connecting your FPGA or microcontroller projects
More informationPLC Stamp micro EVB Datasheet
PLC Stamp micro EVB Datasheet I2SE GmbH March 23, 2016 1/13 CONTENTS CONTENTS Contents 1 Revisions 3 2 Introduction 3 2.1 Handling................................................ 3 3 Reference Documents
More informationRN-171-XV b/g Wireless LAN Module
RN-171-XV 802.11 b/g Wireless LAN Module Features Drop-in Wi-Fi solution for existing systems that currently use 802.15.4 modules Based on Roving Networks robust RN-171 Wi-Fi module Based on a pseudo-standard
More informationXPort Direct+ Integration Guide/Data Sheet
XPort Direct+ Integration Guide/Data Sheet Part Number 900-524 Revision B December 2007 Patents, Copyright and Trademark 2007, Lantronix. All rights reserved. No part of the contents of this book may be
More informationARDUINO PRIMO. Code: A000135
ARDUINO PRIMO Code: A000135 Primo combines the processing power from the Nordic nrf52 processor, an Espressif ESP8266 for WiFi, as well as several onboard sensors and a battery charger. The nrf52 includes
More informationLM780 Bluetooth Serial Data Module 25m Distance with On-Board Antenna
Bluetooth Serial Data Module 25m Distance with On-Board Antenna Product: 1 General Description is LM Technologies Ltd Class 2 Bluetooth Data module with on-board chip antenna. This module is a CSR Bluecore
More informationspecification: imp001
specification: imp001 version 20140812 http://www.electricimp.com 1. Product description 1.1 General description The imp001 is a complete wireless network node in a card form factor. It works in conjunction
More informationSee version notes page for changes EPOS. Aviation M2M LNG
Bluetooth Module with IC Antenna Features Revised 16/MAY/2018 See version notes page for changes Bluetooth.0,.1 wireless technology Configurations preinstalled on production 18 dbm Tx Power and 88 dbm
More informationGWBMA0x Bluetooth Audio module
GWBMA0x Bluetooth Audio module Data sheet version 0.9 draft GWBMA0X DATASHEET 0.9 GIGAWIT 1 Introduction GWBMA1X is a high performance Bluetooth audio module, It provides various type of wireless audio
More informationCM5000 DATASHEET v0.1
CM5000 DATASHEET - 2 - http://www.advanticsys.com/cm5000.html v0.1 Table of Contents 1. INTRODUCTION... 5 2. HARDWARE CHARACTERISTICS... 6 2.1 CM5000 DIAGRAMS... 6 2.2 MICROCONTROLLER DESCRIPTION - TI
More informationRN-174. WiFly GSX Super Module. Features. Description. Applications. rn-174-ds v1.1 1/24/2011
www.rovingnetworks.com rn-174-ds v1.1 1/24/2011 WiFly GSX Super Module Features Development board containing the RN-171 module, status LEDs, power regulator Supports chip antenna (-C), PCB Trace antenna
More informationSerial Port Plug - F2M01SXA Brief Datasheet. Features. Applications. General Description. Provides transparent RS-232 serial cable replacement.
Serial Port Plug - F2M01SXA Features Provides transparent RS-232 serial cable replacement. No need for external drivers. Power is supplied via the D-SUB or mini-usb connector. Supports the Bluetooth Serial
More informationPLC-Stamp micro. I2SE GmbH. April 8, /12
PLC-Stamp micro I2SE GmbH April 8, 2015 1/12 Revisions Revision Release Date Changes 3 April 08, 2015 added information about UART and SPI interface, added MSL information 2 April 16, 2014 added information
More informationZigBee Compliant Platform 2.4G RF Low Power Transceiver Module for IEEE Standard. DATA SHEET Version B
ZMD400-A01 ZigBee Compliant Platform 2.4G RF Low Power Transceiver Module for IEEE 802.15.4 Standard DATA SHEET Version B Quan International Co., Ltd., ZMD400 Features Fully compliant 802.15.4 Standard
More informationSKB360I Bluetooth 4.0 Low Energy Module Datasheet
SKB360I Bluetooth 4.0 Low Energy Module Datasheet Name: Bluetooth 4.0 Low Energy Module Model No.: SKB360I Version: V1.01 Revision History: Revision Description Approved Date V1.01 Initial Release Hogan
More informationWIZ140SR/WIZ145SR Datasheet
WIZ140SR/WIZ145SR Datasheet ( Version 0.9 ) 2010 WIZnet Co., Ltd. All Rights Reserved. For more information, visit our website at http://www.wiznet.co.kr WIZ140SR/WIZ145SR Datasheet (WIZnet Co., Ltd.)
More informationLM780 Bluetooth Module with IC Antenna
Bluetooth Module with C Antenna Revised 8/NO/2017 Features Bluetooth v2.0 / v2.1 specification 26.92mm x 15.20mm x 2.0mm 4 dbm Tx Output Power (Class 2) SMT Side and Bottom Pads for easy production Low
More informationAi-Thinker. ESP-01F Datasheet. Version V1 Copyright Copyright 2018 Shenzhen Ai-Thinker Technology Co., Ltd All Rights Reserved
Copyright 2018 Shenzhen Technology Co., Ltd All Rights Reserved ESP-01F Datasheet Version V1 Copyright 2018 Disclaimer and Copyright Notice Copyright 2018 Shenzhen Technology Co., Ltd All Rights Reserved
More informationCookie User Manual. For NuMicro Edition 1.0. Rev. 1.0 Release: forum.coocox.org.
Cookie User Manual For NuMicro Edition 1.0 Rev. 1.0 Release: 2012-08-09 Website: Forum: Techinal: Market: www.coocox.org forum.coocox.org master@coocox.com market@coocox.com 1 Introduction Cookie is an
More informationOverview. Applications. Features. Pin assignment
Shanghai Yancan Electronic Technology Co., Ltd. Product Name:BLE module Model No.:ZEN-BD98 Overview ZEN-BD98 is a BLE module. By this module, the communication between mobile phone and user s device can
More informationEZmoto V4.1 Product description Rev. 2 30/07/2015
EZmoto V4.1 Product description Rev. 2 30/07/2015 1 Contents 1. Overview... 3 2. Hardware Interface Description... 3 2.1 Main features of the EZmoto... 3 2.2 Hardware block diagram... 4 2.3 Internal Hardware
More informationLM068 Bluetooth v4.1 Dual Mode RS232 Serial Adapter Standalone (With Embedded Bluetooth v4.1 Stack)
Bluetooth v. Dual Mode RS Serial Adapter Revision Draft v.0.mm mm mm Features World s smallest Bluetooth Serial Adapter (RS) Ease of configuration and setup using the LM9v software Bluetooth v. wireless
More informationM M WIFI Module
M1000 150M WIFI Module Stable and High Performance 32bit MIPS Processor Compliant with IEEE 802.11n standard, up to 150Mbps Data Rate Small and Castellated Mounting Holes Design 3.3VDC Input Power, Low
More informationBT53 Datasheet. Amp ed RF Technology, Inc.
BT53 Datasheet Amp ed RF Technology, Inc. 1 BT53 Product Specification Bluetooth features FCC & Bluetooth licensed radio Bluetooth v4.1 Class 1 radio Range up to 80m LOS 13.5mm x 11.6mm x 2.6mm Description
More informationSPWF01SA SPWF01SC. Serial-to-Wi-Fi b/g/n intelligent modules. Features. Applications
SPWF01SA SPWF01SC Serial-to-Wi-Fi b/g/n intelligent modules Datasheet - production data Features 2.4 GHz IEEE 802.11 b/g/n transceiver STM32 ARM Cortex-M3, with 64 KB RAM and 512KB Flash memory 1MByte
More informationHow to create your own peripheral modules for use with the ARC EMSK and embarc
How to create your own peripheral modules for use with the ARC EMSK and embarc Overview embarc is an open software platform designed to help accelerate the development and production of embedded systems
More informationDual Serial Shield User Manual
Dual Serial Shield User Manual PN: 2050 Berkshire Products, Inc. Phone: 770-271-0088 http://www.bkp-store.com/ Rev: 1.00 Copyright 2013 Table of Contents 1 Introduction... 2 1.1 XB compatibility... 2 2
More informationAppNote-US2400-EVB Low Power 2.4GHz Transceiver
US2400-EVB for IEEE 802.15.4 Standard Revision History Hardware Revision Date Description of Changes V01 / V02 Sep. 2011 Initial release V03 Dec 2011 Addition 4.1 Evaluation Board Variants and 5.3 Connector
More informationWLS-TC Specifications
Specifications Document Revision 1.0, February, 2010 Copyright 2010, Measurement Computing Corporation Typical for 25 C unless otherwise specified. Specifications in italic text are guaranteed by design.
More informationProduct Brief. Model: TLM922S-P01A. Ver.1.4
Product Brief Model: TLM922S-P01A Ver.1.4 1 Index 1. Overview... 3 2. Product Features... 3 3. Application... 4 4. Product Specifications... 4 5. PIN Definition... 5 6. PCB Dimension... 6 7. Pin Configuration...
More informationWiMOD - ic880a. Application Note AN014 / Version 1.3. USB modifications for direct SPI operation. Document ID: 4000/40140/0079
WiMOD - ic880a Application Note AN014 / Version 1.3 USB modifications for direct SPI operation Document ID: 4000/40140/0079 IMST GmbH Carl-Friedrich-Gauss-Str. 2-4 D-47475 Kamp-Lintfort Overview Document
More informationQFBR-S01IN001Z. Optical Phase Interrogator. Data Sheet. Description. Features. Applications
Optical Phase Interrogator Description The QFBR-S01IN001Z is a versatile optical phase interrogation (OPI) unit based on Avago proprietary technology. The working principle is based on comparing a fixed
More informationApplications Wi-Fi sensors Wi-Fi automation Internet of things Wi-Fi enterteinment Serial to Wi-Fi
Introduction Flyport is a revolutionary WiFi module based on the open source platform openpicus. Flyport is not simply a serial to WiFi solution, but a smart module with no need of an external host processor
More informationLM780 Bluetooth Serial Data Module
Features Bluetooth v2.0 + EDR and v2.1 + EDR compliant firmware available Class 2 radio with integrated chip antenna - 25 m range in open space Lead Free, RoHS compliant Small Size: 15.24mm x 27.67mm x
More informationLM780 Bluetooth Module with IC Antenna
Bluetooth Module with C Antenna Revised 11/JAN/2018 Datasheet ersion 1.0 Features Bluetooth v2.0 / v2.1 specification 26.92mm x 15.20mm x 2.0mm 4 dbm Tx Output Power (Class 2) SMT Side and Bottom Pads
More informationRN-174. WiSnap M2 Super Module. Features. Description. Applications. ~ page 1 ~ rn-174-ds v1.1 6/1/2011
WiSnap M2 Super Module Features Development board containing the RN-171 module, status LEDs, power regulator Supports chip antenna (RN-174-C), PCB Trace antenna (RN-174-P), wire antenna (RN- 174-W) and
More informationLM048 Bluetooth v2.0, v2.1 RS232 Serial Adapter Standalone (With Embedded Bluetooth v2.0 / v2.1 Stack)
Bluetooth v.0, v. RS Serial Adapter Revised 8/NOV/0.mm mm mm Features World s smallest Bluetooth Serial Adapter (RS) Bluetooth v.0, v. wireless technology 8 dbm Tx Power and -8 dbm Rx Sensitivity Serial
More informationRN-174 WiFly Super Module
RN- WiFly Super Module Features Evaluation board for the RN- module Supports chip antenna (RN--C), PCB trace antenna (RN--P), wire antenna (RN--W), and U.FL connector for an external antenna (RN--U) Ultra-low
More informationData Sheet. QFBR-S01IN001Z Optical Phase Interrogator. Description. Features. Applications
QFBR-S01IN001Z Optical Phase Interrogator Data Sheet Description Avago technologies QFBR-S01IN001Z is a versatile optical phase interrogation (OPI) unit based on Avago proprietary technology. The working
More informationOpenPicus WIFI module. Introduction. Pinout. Features
Introduction FLYPORT is a professional, slim, wireless module ready for integration in brand new or existing electronic products. Based on Microchip PIC 24F256FJ106GA 16 bits processors and the Microchip
More informationProduct Datasheet: DWM1001-DEV DWM1001 Module Development Board. Key Features and Benefits
Product Datasheet: DWM1001-DEV DWM1001 Module Development Board Plug-and-Play Development Board for evaluating the performance of the Decawave DWM1001 module Easily assemble a fully wireless RTLS system,
More informationLogic Way GmbH, DIMM-CPU-CB09.odt
Logic Way GmbH, http://www.logicway.de 2010-12-17 DIMM-CPU-CB 09 Breakout and interface board for vehicle application with 2xCAN, 2x2.4GHz IEEE802.15.4 radio, GPS receiver, GSM/GPRS modem, RTC, SD card,
More informationLM072 Bluetooth Module Standalone (With Embedded Bluetooth v2.0/v2.1 Stack)
Bluetooth Module Revised 3/JAN/2018 2.8mm 28.2mm 15mm Features Bluetooth v2.0, v2.1 wireless technologiy SMT Side and Bottom Pads for easy production 18 dbm Tx Output Power and 82 dbm Rx Sensitivity See
More informationRN-134. WiFly GSX Super Module SuRF Board. Features. Description. Applications. ~ page 1 ~ rn-134-ds v1.
WiFly GSX Super Module SuRF Board Features UART interface with RS232 and TTL signaling Through hole board simplifies system integration Accepts 3-12VDC Status LEDs to show network status and data transfer
More information802.11b/g/n IOT Module
802.11b/g/n Industrial-Grade IOT Module, Qualcomm Atheros QCA4010, 1T1R Feature Standard: 802.11b/g/n Host Interface: UART, SPI/SDIO, I2C/I2S, USB, ADC Chipset: Qualcomm Atheros QCA4010 Antenna: PCB Printed
More informationLBM313 Datasheet. Version 0.20 March 27, 2014
LBM313 Datasheet Version 0.20 March 27, 2014 1 Introduction The LightBlueM Module is a full-featured Bluetooth 4.0 module with built in 8-bit SoC. It is based on Texas Instruments CC2540 system on chip.
More informationSPWF01SA SPWF01SC. Serial-to-Wi-Fi b/g/n intelligent modules. Applications. Features
SPWF01SA SPWF01SC Serial-to-Wi-Fi b/g/n intelligent modules Datasheet - production data Industrial operating temperature range FCC/CE/IC certified RoHS compliant Surface mount PCB module Applications SPWF01SA
More informationBLUETOOTH MODULE. Model BT-20
BLUETOOTH MODULE Model BT-20 Device Features 3.3V power operation Fully qualified by BQB Full speed Bluetooth operation with full piconet support 8M flash memory for application firmware Applications PC
More informationUser Guide. Release r01
Release r01 Note This device was developed for the purpose of communication in an office environment. It is intended solely for our industrial clients for physical integration into their own technical
More informationBluetooth RS-232 Dongle. User s Manual BTS-100
Bluetooth RS-232 Dongle User s Manual BTS-100 Table of Contents 1. INTRODUCTION... 2 2. PHYSICAL DIAGRAM... 3 3. BLUETOOTH PAIRING AND CONNECTING... 4 4. RS-232 INSTALLATION... 10 5. HYPERTERMINAL SETTING
More informationWireless Sensor Networks. FireFly 2.2 Datasheet
2.2 Datasheet July 6, 2010 This page intentionally left blank. Contents 1. INTRODUCTION...1 Features...1 Applications...2 2. BLOCK DIAGRAM...3 3. HARDWARE CONNECTIONS...4 Power...5 Header 1 ( UARTS, I2C,
More informationProduct Brief. Model: TLM922S-P01A. Ver.1.0
Product Brief Model: TLM922S-P01A Ver.1.0 1 Index 1. Overview... 3 2. Product Features... 3 3. Application... 4 4. Product Specifications... 4 5. PIN Definition... 6 6. PCB Dimension... 7 7. Pin Configuration...
More informationPage 1 of 11 Version 1.2 Release Date: PenMount PM2204 PCI Controller Board Data Sheet. Table of contents
Page 1 of 11 Table of contents Table of contents... 1 Revision history... 2 1.0 Introduction... 3 2.0 Specifications... 4 3.0 Mechanical drawing... 5 3.1 Mechanical size... 5 3.2 Touch line pin definition...
More informationAQ_G24 GSM Terminal Card Motorola Cellular GSM Engine
AQ_G24 GSM Terminal Card Motorola Cellular GSM Engine Version: 01.01 AQ_G24 Terminal Card_HD_V01.01 17.JUL.2008-1 - Hardware Interface Description 1. Hardware Features of the AQ_G24 Terminal Card Feature
More informationLM961 Bluetooth Dual Mode Module Standalone (With Embedded Bluetooth v4.1 Stack)
Bluetooth Dual Mode Module Revised 13/DEC/2017 18.9mm 2.55mm 12.71mm Features Bluetooth v4.1 specification (Dual Mode) Fully integrated module with no additional components required Class 1 Tx Out Power
More informationLM058 Bluetooth v2.0, v2.1 RS232 Serial Adapter - SMA Connector Standalone (With Embedded Bluetooth v2.0 / v2.1 Stack)
Bluetooth v2.0, v2. RS232 Serial Adapter - SMA Connector Revised 3/MAR/20 Datasheet Version.0 mm mm 34mm Features Bluetooth v2.0, v2. wireless technology dbm Tx Power and - dbm Rx Sensitivity Serial (RS232)
More informationG80 SoC Datasheet. Where Hardware Meets Software
GHI Electronics, LLC 501 E. Whitcomb Ave. Madison Heights, Michigan 48071 Phone: (248) 397-8856 Fax: (248) 397-8890 www.ghielectronics.com G80 SoC Datasheet Where Hardware Meets Software GHI Electronics,
More informationWIZnet PRODUCT GUIDE.
WIZnet PRODUCT GUIDE www.wiznet.co.kr www.wiznettechnology.com Ethernet Controller and Microcontroller Ethernet Controller and Microcontroller Embedded Core W5200 W5100 W5300 TCP/IP + MAC + PHY TCP/IP
More informationEmbedded WiFi Module for M2M and IOT
INGICS TECHNOLOGY SPECIFICATION Ver. 1C iwm021 Feb, 2015 Embedded WiFi Module for M2M and IOT size 20mmX15mm INGICS TECHNOLOGY CO., LTD. SUPPORT@INGICS.COM WWW.INGICS.COM 1 Contents Contents Introduction
More informationProduct Overview: DWM1001-DEV DWM1001 Module Development Board. Key Features and Benefits
Product Overview: DWM1001-DEV DWM1001 Module Development Board Plug-and-Play Development Board for evaluating the performance of the Decawave DWM1001 module Easily assemble a fully wireless RTLS system,
More informationWU106 IoT WLAN Module Datasheet
WU106 IoT WLAN Module Datasheet Document Information Title WU106 Document type Datasheet Document number SL-18020008 Revision and date V1.03 03-Mar -2018 Disclosure restriction Public 1 / 13 WU106-DA-001,A/1
More informationBT121 BLUETOOTH SMART READY MODULE
BT121 BLUETOOTH SMART READY MODULE DATA SHEET Tuesday, 09 June 2015 Document Version: 1.41 Copyright Silicon Labs All rights reserved. Silicon Labs assumes no liability or responsibility for any errors,
More informationFrequently Asked Questions
Bluetooth low energy Module Frequently Asked Questions Rev. record 29-Sep.-2017> Ver.1.0 Release 1. General Q1-1: How to order the modules, evaluation boards (EVB) and evaluation kits (EVK)? A1-1: To order,
More informationRN-174. WiFly GSX Super Module. Features. Description. Applications. rn-174-ds v1.1 4/20/2011
www.rovingnetworks.com rn-174-ds v1.1 4/20/2011 WiFly GSX Super Module Features Development board containing the RN-171 module, status LEDs, power regulator Supports chip antenna (-C), PCB Trace antenna
More informationUnwired One. Main Features. Wireless embedded computer
Main Features High performance 400 MHz MIPS24K processor core Ultra-compact 25 35 4mm form-factor 802.11 b/g/n and Ethernet support Integrated 2.4 GHz Wi-Fi antenna USB 2.0 interface support SPI, UART,
More informationCB-1 Peripheral Board Technical Manual
CB-1 Peripheral Board Technical Manual Date: 13 May 2007 Document Revision: 1.02 BiPOM Electronics 16301 Blue Ridge Road, Missouri City, Texas 77489 Telephone: 1-713-283-9970. Fax: 1-281-416-2806 E-mail:
More informationSpecification. Delock industry USB WLAN 144Mbps module. date: ,50 60,00 25,00
5,50 60,00 25,00 date: 16.03.2009 Contents: device overall description 802.11n Wireless LAN - features - block diagram - modulation methods - channel assignment - security - software & OS support - operating
More informationBluetooth Interface Module
Bluetooth Interface Module Datasheet Bluetooth Interface Module Product Overview Bluetooth Interface Module provides the Bluetooth Communication between CPU Board and any Bluetooth enabled device. This
More informationSession 4. Embedded Wireless LAN Module. (WizFi210/220) Ultra Low Power. WIZnet EU 2012 MARCH - 1 -
Session 4 Ultra Low Power Embedded Wireless LAN Module (WizFi210/220) WIZnet EU - 1-2012 MARCH Contents Wi-Fi Product Roadmap Specification WizFi210 Feature WIZnet Wi-Fi module comparison Target Application
More informationEM35x Ember Companion Kit Technical User Guide
Technical User Guide EM35x Ember Companion Kit Technical User Guide 0008-02-17-00-000 EM35x Ember Companion Kit Technical User Guide Module Definition Each module is soldered on a carrier board making
More informationOLS425 / OLP425 series
OLS425 / OLP425 series Stand-alone Bluetooth low energy modules Electrical Mechanical Data Sheet Abstract This document describes the hardware characteristics of the OEM Bluetooth Low Energy Platform (OLP425)
More informationDEVBOARD3 DATASHEET. 10Mbits Ethernet & SD card Development Board PIC18F67J60 MICROCHIP
DEVBOARD3 DATASHEET 10Mbits Ethernet & SD card PIC18F67J60 MICROCHIP Version 1.0 - March 2009 DEVBOARD3 Version 1.0 March 2009 Page 1 of 7 The DEVBOARD3 is a proto-typing board used to quickly and easily
More informationCarambola2 (-I) Data sheet. Carambola2 is a tiny surface mountable 2.4 GHz Wi-Fi module running OpenWRT linux software
(-I) is a tiny surface mountable 2.4 GHz Wi-Fi module running OpenWRT linux software 8devices is a member of Carambola wireless modules family and is based on Qualcomm/Atheros AR9331 SoC. is a surface
More informationWireless LAN Module. IEEE802.11b/g/n WYSAGVDX7
Wireless LAN Module IEEE802.11b/g/n WYSAGVDX7 Application Note In case you adopt this module and design some appliance, please ask for the latest specifications to the local sales office. 1/12 Table of
More informationRadiocrafts Embedded Wireless Solutions
CEF Ultra-Low Power sub-1 GHz Radio Module platform Product Description The RC18x0 Radio Module platforms are a series of compact surface-mounted ultra-low power RF modules based on the CC1310 system-on-chip
More informationWizFi220 follows all of information described in this documents
WizFi210 Datasheet (Version 1.20) WizFi220 follows all of information described in this documents 2013 WIZnet Co., Ltd. All Rights Reserved. For more information, visit our website at http://www.wiznet.co.kr
More information