Stresses in an Elliptical Beam
|
|
- Claud Arnold
- 5 years ago
- Views:
Transcription
1 Problem: An offset tensile link is shaped to clear an obstruction with a geometry as shown in the figure. The cross section at the critical location is elliptical, with a major axis of 4 in and a minor axis of 2 in. For a load of 20 kip, estimate the stresses at the inner and outer surfaces of the critical section Joseph Shigley and Charles Mischke. Mechanical Engineering Design 5th ed. New York: McGraw Hill, May 2002.
2 Overview Anticipated time to complete this tutorial: 30 minutes Tutorial Overview This tutorial is divided into five parts: 1) Tutorial Basics 2) Preprocessing 3) Solution 4) Post Processing 5) Hand Calculations Audience This tutorial assumes familiarity of ANSYS 8.0; therefore, it does not go into step by step detail. Prerequisites 1) ANSYS 8.0 in house Structural Tutorial 2) Completion of all Basic Machine Design Tutorials 3) Completion of three or more Guided Machine Design Tutorials 4) Completion of Guided Utility Hook Tutorial Objectives 1) Create an elliptical area 2) Create volumes by sweeping areas 3) Use symmetry boundary constraints to simplify the problem 4) Find the inner and outer stresses of a curved beam Outcomes 1) Explore possibilities with the graphical user interface (GUI) 2) Learn how to create and mesh simple geometries 3) Increase efficiency in problem set up and solving speed 2
3 In this tutorial: Instructions appear on the left. Visual aids corresponding to the text appear on the right. Tutorial Basics All commands on the toolbars are labeled. However, only operations applicable to the tutorial are explained. The instructions should be used as follows: Bold > Example: Italics MB1 MB2 MB3 Text in bold are buttons, options, or selections that the user needs to click on > Preprocessor > Element Type > Add/Edit/DeleteFile would mean to follow the options as shown to the right to get you to the Element Types window Text in italics are hints and notes Click on the left mouse button Click on the middle mouse button Click on the right mouse button Some basic ANSYS functions are: To rotate the models use Ctrl and MB3. To zoom use Ctrl and MB2 and move the mouse up and down. To translate the models use Ctrl and MB1. 3
4 Preprocessing 1) Setup the necessary preprocessor parameters. Add an element. Add a material model. Note: Use Solid 185 and assume steel 2) Create a sufficient number of keypoints that represents the geometry of an ellipse. To create the spline: > Preprocessor > Modeling > Create > Lines > Splines > Spline thru KPs Select half of the keypoints at first, then select the other half. Create the elliptical area by arbitrary lines. Add 3 more keypoints to complete half the geometry of the problem. Connect keypoints as shown to the right. Note: Use Arcs by end KPs & Rad and straight line Add a Line fillet where the two lines connect. Note: Use a radius of 10. Use the extrude areas along lines command to create the volume of the link. Before meshing the model, add a hard point in the center of the left edge cross section where the force will be applied 4
5 Solution 3) Mesh the model. If possible, use the volume sweep command. Note: Select Smart size and reduce the fine mesh to 3. Doing this should allow you not to have the error shown below. 4) Apply a symmetric boundary condition. > Solution > Define Loads > Apply > Structural > Displacement > Symmetry B.C. > On Areas Select the area shown to the right in purple. 5) Apply the lb load. 6) Solve the model. 5
6 Post Processing 7) Use the post processing tools to get the inner and outer stress values. > General Postproc > Results Viewer Then select the Von Mises stress. To better read the results, > General Postproc > List Results > Nodal Solution > Stress > Principal For this model, node 1 & 2 represent the outer and inner nodes of the critical section. The inner stress is about kpsi and the outer was about kpsi. The answers are relatively close to the analytical solution (about 3 % error). Try resolving the problem using different meshes and mesh densities to see if you can get solutions that are closer to the analytical ones. 6
7 Hand Calculations The numerical integration was carried out using Simpson s rule. r b br b/r A = ( ) = in 3.4( ) R = = in. 3( ) r n = = in..4( ) 3 The eccentricity e is then e = R rn = = in. For comparison, using 21 ordinates; 2 A = in R = 12in r n = e = in Continuing with the 11 -ordinate analysis, c = = in c i o = = in M = F(2 + 2) = 20000(4) = 80000inlb σ = σ i o = ( ) ( ) ( ) ( )14 = psi = psi 7
8 Hand Calculations Note that A, R, r n were evaluated by numerical integration even though it is possible to I 2 write A= ðab and R=12 by inspection. This is because R= where integral errors are I1 I1 correlated. Similarly r n =. This approach leads to more accurate R and r n and also I3 improves the estimate of e, something to keep in mind when writing computer programs. 8
Latch Spring. Problem:
Problem: Shown in the figure is a 12-gauge (0.1094 in) by 3/4 in latching spring which supports a load of F = 3 lb. The inside radius of the bend is 1/8 in. Estimate the stresses at the inner and outer
More informationBell Crank. Problem: Joseph Shigley and Charles Mischke. Mechanical Engineering Design 5th ed (New York: McGraw Hill, May 2002) page 87.
Problem: A cast-iron bell-crank lever, depicted in the figure below is acted upon by forces F 1 of 250 lb and F 2 of 333 lb. The section A-A at the central pivot has a curved inner surface with a radius
More informationBuckling of Euler Column
Problem: An Euler column with one end fixed and one end free is to be made of an aluminum alloy (E = 71 GPa). The cross sectional area of the column is 600 mm and the column is.5 m long. Determine the
More informationStatically Indeterminate Beam
Problem: A rectangular aluminum bar.5 inches thick and 2 inches wide is welded to fixed supports at the ends, and the bar supports a load W=800 lb, acting through the pin as shown. Find the reactions at
More informationStatically Indeterminate Beam
Problem: Using Castigliano's Theorem, determine the deflection at point A. Neglect the weight of the beam. W 1 N/m B 5 cm H 1 cm 1.35 m Overview Anticipated time to complete this tutorial: 45 minutes Tutorial
More informationTruss Optimization. Problem:
Problem: Assuming that the compression members of the truss showing in the figure will not buckle, find the minimum cross sectional area of each member using an allowable stress of 50 MPa. The dimensions
More informationTruss Bracket. Problem:
Problem: The truss structure shown above is mounted on the sides of buildings during construction for use as scaffolding for workers. A design team has created a new bracket design (shown below) to use
More informationBuckling (with sections)
roblem: An Euler column with one end fixed and one end free is to be made of an aluminum alloy (E = 71 Ga). The oss sectional area of the column is 600 mm and the column is.5 m long. Determine the column
More informationStiffness of Tapered Beam
Problem: A bar in tension has a conical shape of length L. The task is to find the stiffness of the tapered section. Compare the stiffness given by ANSYS to the theoretical stiffness given by: EA1 ( r2
More informationExercise 1. 3-Point Bending Using the GUI and the Bottom-up-Method
Exercise 1 3-Point Bending Using the GUI and the Bottom-up-Method Contents Learn how to... 1 Given... 2 Questions... 2 Taking advantage of symmetries... 2 A. Preprocessor (Setting up the Model)... 3 A.1
More informationChapter 2. Structural Tutorial
Chapter 2. Structural Tutorial Tutorials> Chapter 2. Structural Tutorial Static Analysis of a Corner Bracket Problem Specification Problem Description Build Geometry Define Materials Generate Mesh Apply
More informationfile://c:\documents and Settings\sala\Configuración local\temp\~hha54f.htm
Página 1 de 26 Tutorials Chapter 2. Structural Tutorial 2.1. Static Analysis of a Corner Bracket 2.1.1. Problem Specification Applicable ANSYS Products: Level of Difficulty: Interactive Time Required:
More informationLecture # 5 Modal or Dynamic Analysis of an Airplane Wing
Lecture # 5 Modal or Dynamic Analysis of an Airplane Wing Problem Description This is a simple modal analysis of a wing of a model airplane. The wing is of uniform configuration along its length and its
More informationExercise 2: Bike Frame Analysis
Exercise 2: Bike Frame Analysis This exercise will analyze a new, innovative mountain bike frame design under structural loads. The objective is to determine the maximum stresses in the frame due to the
More informationExercise 2: Bike Frame Analysis
Exercise 2: Bike Frame Analysis This exercise will analyze a new, innovative mountain bike frame design under structural loads. The objective is to determine the maximum stresses in the frame due to the
More informationCourse in ANSYS. Example0303. ANSYS Computational Mechanics, AAU, Esbjerg
Course in Example0303 Example Gear axle 3D Objective: Compute the maximum stress von Mise Tasks: How should this be modeled? Topics: Element type, Real constants, modeling, Plot results, output graphics,
More informationES 230 Strengths Intro to Finite Element Modeling & Analysis Homework Assignment 5
ES 230 Strengths Intro to Finite Element Modeling & Analysis Homework Assignment 5 The GREAT Combined Load Problem Moving on to Principal Stresses and von Mises Failure Criteria Open up your ANSYS model
More informationTUTORIAL 7: Stress Concentrations and Elastic-Plastic (Yielding) Material Behavior Initial Project Space Setup Static Structural ANSYS ZX Plane
TUTORIAL 7: Stress Concentrations and Elastic-Plastic (Yielding) Material Behavior In this tutorial you will learn how to recognize and deal with a common modeling issues involving stress concentrations
More informationANSYS. Geometry. Material Properties. E=2.8E7 psi v=0.3. ansys.fem.ir Written By:Mehdi Heydarzadeh Page 1
Attention: This tutorial is outdated, you will be redirected automatically to the new site. If you are not redirected, click this link to the confluence site. Problem Specification Geometry Material Properties
More informationProblem (From Shigley and Mischke Mechanical Engineering Design)
Problem 7-20 (From Shigley and Mischke Mechanical Engineering Design) Start by building the part shown in problem 7-20 in the textbook, make sure you are in English (IPS) units. Next, apply a material
More informationExample Cantilever beam
Course in ANSYS Example0300 Example Cantilever beam Objective: Compute the maximum deflection and locate point of maximum deflection Tasks: How should this be modelled? Compare results with results obtained
More informationTWO-DIMENSIONAL PROBLEM OF THE THEORY OF ELASTICITY. INVESTIGATION OF STRESS CONCENTRATION FACTORS.
Ex_1_2D Plate.doc 1 TWO-DIMENSIONAL PROBLEM OF THE THEORY OF ELASTICITY. INVESTIGATION OF STRESS CONCENTRATION FACTORS. 1. INTRODUCTION Two-dimensional problem of the theory of elasticity is a particular
More informationSESAM USER MANUAL. GeniE Tutorial. Semi Pontoon Workshop SAFER, SMARTER, GREENER
SESAM USER MANUAL GeniE Tutorial Semi Pontoon Workshop SAFER, SMARTER, GREENER Sesam User Manual GeniE Tutorial Semi Pontoon Workshop Date: 29 January 2015 Valid from GeniE V7.0 Prepared by DNV GL - Software
More informationANSYS 5.6 Tutorials Lecture # 2 - Static Structural Analysis
R50 ANSYS 5.6 Tutorials Lecture # 2 - Static Structural Analysis Example 1 Static Analysis of a Bracket 1. Problem Description: The objective of the problem is to demonstrate the basic ANSYS procedures
More informationTypes of Idealizations. Idealizations. Cylindrical Shaped Part. Cyclic Symmetry. 3D Shell Model. Axisymmetric
Types of Idealizations Idealizations Selecting the model type 3D Solid Plane Stress Plane Strain 3D Shell Beam Cyclic Symmetry Cylindrical Shaped Part Interior Pressure Load 3D model can be used to model
More information3D Design with 123D Design
3D Design with 123D Design Introduction: 3D Design involves thinking and creating in 3 dimensions. x, y and z axis Working with 123D Design 123D Design is a 3D design software package from Autodesk. A
More informationMAE 323: Lab 7. Instructions. Pressure Vessel Alex Grishin MAE 323 Lab Instructions 1
Instructions MAE 323 Lab Instructions 1 Problem Definition Determine how different element types perform for modeling a cylindrical pressure vessel over a wide range of r/t ratios, and how the hoop stress
More informationInstitute of Mechatronics and Information Systems
EXERCISE 4 Free vibrations of an electrical machine model Target Getting familiar with the fundamental issues of free vibrations analysis of a simplified model of an electrical machine, with the use of
More informationSimilar Pulley Wheel Description J.E. Akin, Rice University
Similar Pulley Wheel Description J.E. Akin, Rice University The SolidWorks simulation tutorial on the analysis of an assembly suggested noting another type of boundary condition that is not illustrated
More informationRelease 10. Kent L. Lawrence. Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
ANSYS Release 10 Tutorial Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
More informationANSYS Tutorial Release 11.0
ANSYS Tutorial Release 11.0 Structural & Thermal Analysis Using the ANSYS Release 11.0 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More informationExercise 1. 3-Point Bending Using the Static Structural Module of. Ansys Workbench 14.0
Exercise 1 3-Point Bending Using the Static Structural Module of Contents Ansys Workbench 14.0 Learn how to...1 Given...2 Questions...2 Taking advantage of symmetries...2 A. Getting started...3 A.1 Choose
More informationStructural static analysis - Analyzing 2D frame
Structural static analysis - Analyzing 2D frame In this tutorial we will analyze 2D frame (see Fig.1) consisting of 2D beams with respect to resistance to two different kinds of loads: (a) the downward
More informationModeling a Gear Standard Tools, Surface Tools Solid Tool View, Trackball, Show-Hide Snaps Window 1-1
Modeling a Gear This tutorial describes how to create a toothed gear. It combines using wireframe, solid, and surface modeling together to create a part. The model was created in standard units. To begin,
More informationStructural modal analysis - 2D frame
Structural modal analysis - 2D frame Determine the first six vibration characteristics, namely natural frequencies and mode shapes, of a structure depicted in Fig. 1, when Young s modulus= 27e9Pa, Poisson
More informationA pipe bend is subjected to a concentrated force as shown: y All dimensions in inches. Material is stainless steel.
Problem description A pipe bend is subjected to a concentrated force as shown: y 15 12 P 9 Displacement gauge Cross-section: 0.432 18 x 6.625 All dimensions in inches. Material is stainless steel. E =
More informationModule 1.7W: Point Loading of a 3D Cantilever Beam
Module 1.7W: Point Loading of a 3D Cantilever Beam Table of Contents Page Number Problem Description 2 Theory 2 Workbench Analysis System 4 Engineering Data 5 Geometry 6 Model 11 Setup 13 Solution 14 Results
More informationANSYS AIM Tutorial Structural Analysis of a Plate with Hole
ANSYS AIM Tutorial Structural Analysis of a Plate with Hole Author(s): Sebastian Vecchi, ANSYS Created using ANSYS AIM 18.1 Problem Specification Pre-Analysis & Start Up Analytical vs. Numerical Approaches
More informationANSYS AIM Tutorial Stepped Shaft in Axial Tension
ANSYS AIM Tutorial Stepped Shaft in Axial Tension Author(s): Sebastian Vecchi, ANSYS Created using ANSYS AIM 18.1 Contents: Problem Specification 3 Learning Goals 4 Pre-Analysis & Start Up 5 Calculation
More informationCATIA V5 Parametric Surface Modeling
CATIA V5 Parametric Surface Modeling Version 5 Release 16 A- 1 Toolbars in A B A. Wireframe: Create 3D curves / lines/ points/ plane B. Surfaces: Create surfaces C. Operations: Join surfaces, Split & Trim
More informationExample Plate with a hole
Course in ANSYS Example Plate with a hole A Objective: Determine the maximum stress in the x-direction for point A and display the deformation figure Tasks: Create a submodel to increase the accuracy of
More informationCourse in ANSYS. Example Truss 2D. Example0150
Course in ANSYS Example0150 Example Truss 2D Objective: Compute the maximum deflection Tasks: Display the deflection figure? Topics: Topics: Start of analysis, Element type, Real constants, Material, modeling,
More informationNonLinear Analysis of a Cantilever Beam
NonLinear Analysis of a Cantilever Beam Introduction This tutorial was created using ANSYS 7.0 The purpose of this tutorial is to outline the steps required to do a simple nonlinear analysis of the beam
More informationAnsys Lab Frame Analysis
Ansys Lab Frame Analysis Analyze the highway overpass frame shown in Figure. The main horizontal beam is W24x162 (area = 47.7 in 2, moment of inertia = 5170 in 4, height = 25 in). The inclined members
More informationAufgabe 1: Dreipunktbiegung mit ANSYS Workbench
Aufgabe 1: Dreipunktbiegung mit ANSYS Workbench Contents Beam under 3-Pt Bending [Balken unter 3-Pkt-Biegung]... 2 Taking advantage of symmetries... 3 Starting and Configuring ANSYS Workbench... 4 A. Pre-Processing:
More information3. Preprocessing of ABAQUS/CAE
3.1 Create new model database 3. Preprocessing of ABAQUS/CAE A finite element analysis in ABAQUS/CAE starts from create new model database in the toolbar. Then save it with a name user defined. To build
More informationBattery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
More informationSpur Gears Static Stress Analysis with Linear Material Models
Exercise A Spur Gears Static Stress Analysis with Linear Material Models Beam and Brick Elements Objective: Geometry: Determine the stress distribution in the spur gears when a moment of 93.75 in-lb is
More informationThe Essence of Result Post- Processing
APPENDIX E The Essence of Result Post- Processing Objectives: Manually create the geometry for the tension coupon using the given dimensions then apply finite elements. Manually define material and element
More informationTwo Dimensional Truss
Two Dimensional Truss Introduction This tutorial was created using ANSYS 7.0 to solve a simple 2D Truss problem. This is the first of four introductory ANSYS tutorials. Problem Description Determine the
More informationInstitute of Mechatronics and Information Systems
EXERCISE 2 Free vibrations of a beam arget Getting familiar with the fundamental issues of free vibrations analysis of elastic medium, with the use of a finite element computation system ANSYS. Program
More informationStructural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment. Kent L. Lawrence
ANSYS Workbench Tutorial Structural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More informationStructural static analysis - Analyzing 2D frame
Structural static analysis - Analyzing 2D frame In this tutorial we will analyze 2D frame (see Fig.1) consisting of 2D beams with respect to resistance to two different kinds of loads: (a) the downward
More informationC-clamp FEA Analysis
C-clamp FEA Analysis ME 341 students are asked to determine the stresses on the inner and outer surface of a C-clamp at a point on the curved section and the straight section of the clamp. The following
More informationTRINITAS. a Finite Element stand-alone tool for Conceptual design, Optimization and General finite element analysis. Introductional Manual
TRINITAS a Finite Element stand-alone tool for Conceptual design, Optimization and General finite element analysis Introductional Manual Bo Torstenfelt Contents 1 Introduction 1 2 Starting the Program
More informationTHREE DIMENSIONAL DYNAMIC STRESS ANALYSES FOR A GEAR TEETH USING FINITE ELEMENT METHOD
THREE DIMENSIONAL DYNAMIC STRESS ANALYSES FOR A GEAR TEETH USING FINITE ELEMENT METHOD Haval Kamal Asker Department of Mechanical Engineering, Faculty of Agriculture and Forestry, Duhok University, Duhok,
More informationStructural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment
ANSYS Workbench Tutorial Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More informationPro MECHANICA STRUCTURE WILDFIRE 4. ELEMENTS AND APPLICATIONS Part I. Yves Gagnon, M.A.Sc. Finite Element Analyst & Structural Consultant SDC
Pro MECHANICA STRUCTURE WILDFIRE 4 ELEMENTS AND APPLICATIONS Part I Yves Gagnon, M.A.Sc. Finite Element Analyst & Structural Consultant SDC PUBLICATIONS Schroff Development Corporation www.schroff.com
More informationEmbedded Reinforcements
Embedded Reinforcements Gerd-Jan Schreppers, January 2015 Abstract: This paper explains the concept and application of embedded reinforcements in DIANA. Basic assumptions and definitions, the pre-processing
More informationExercise 1: 3-Pt Bending using ANSYS Workbench
Exercise 1: 3-Pt Bending using ANSYS Workbench Contents Starting and Configuring ANSYS Workbench... 2 1. Starting Windows on the MAC... 2 2. Login into Windows... 2 3. Start ANSYS Workbench... 2 4. Configuring
More informationAbaqus/CAE Axisymmetric Tutorial (Version 2016)
Abaqus/CAE Axisymmetric Tutorial (Version 2016) Problem Description A round bar with tapered diameter has a total load of 1000 N applied to its top face. The bottom of the bar is completely fixed. Determine
More informationSDC. Engineering Analysis with COSMOSWorks. Paul M. Kurowski Ph.D., P.Eng. SolidWorks 2003 / COSMOSWorks 2003
Engineering Analysis with COSMOSWorks SolidWorks 2003 / COSMOSWorks 2003 Paul M. Kurowski Ph.D., P.Eng. SDC PUBLICATIONS Design Generator, Inc. Schroff Development Corporation www.schroff.com www.schroff-europe.com
More informationEach trainee receives the official 260 page courseware as part of attending this course.
Level 1 NURBS modelling with Rhino Course Outline This course is for anyone new, or nearly new, to Rhino. Recognised as THE introductory course for Rhino, all trainees receive an Official Certificate on
More informationExercise 1: Axle Structural Static Analysis
Exercise 1: Axle Structural Static Analysis The purpose of this exercise is to cover the basic functionality of the Mechanical Toolbar (MTB) in the context of performing an actual analysis. Details of
More informationStatic Stress Analysis
Static Stress Analysis Determine stresses and displacements in a connecting rod assembly. Lesson: Static Stress Analysis of a Connecting Rod Assembly In this tutorial we determine the effects of a 2,000-pound
More informationGeometry Clean-up in. Numerical Simulations
Geometry Clean-up in Numerical Simulations Scope of the this Presentation The guidelines are very generic in nature and has been explained with examples. However, the users may need to check their software
More informationNonLinear Materials AH-ALBERTA Web:
NonLinear Materials Introduction This tutorial was completed using ANSYS 7.0 The purpose of the tutorial is to describe how to include material nonlinearities in an ANSYS model. For instance, the case
More informationModule 1.7: Point Loading of a 3D Cantilever Beam
Module 1.7: Point Loading of a D Cantilever Beam Table of Contents Page Number Problem Description Theory Geometry 4 Preprocessor 6 Element Type 6 Material Properties 7 Meshing 8 Loads 9 Solution 15 General
More informationME Week 12 Piston Mechanical Event Simulation
Introduction to Mechanical Event Simulation The purpose of this introduction to Mechanical Event Simulation (MES) project is to explorer the dynamic simulation environment of Autodesk Simulation. This
More informationWORKSHOP 6.3 WELD FATIGUE USING NOMINAL STRESS METHOD. For ANSYS release 14
WORKSHOP 6.3 WELD FATIGUE USING NOMINAL STRESS METHOD For ANSYS release 14 Objective: In this workshop, a weld fatigue analysis on a VKR-beam with a plate on top using the nominal stress method is demonstrated.
More informationLesson: Static Stress Analysis of a Connecting Rod Assembly
Lesson: Static Stress Analysis of a Connecting Rod Assembly In this tutorial we determine the effects of a 2,000 pound tensile load acting on a connecting rod assembly (consisting of the rod and two pins).
More informationSOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users
SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users The premium provider of learning products and solutions www.cadartifex.com Table of Contents Dedication... 3 Preface... 15 Part 1. Introducing
More informationEssay 5 Tutorial for a Three-Dimensional Heat Conduction Problem Using ANSYS
Essay 5 Tutorial for a Three-Dimensional Heat Conduction Problem Using ANSYS 5.1 Introduction The problem selected to illustrate the use of ANSYS software for a three-dimensional steadystate heat conduction
More informationLicom Systems Ltd., Training Course Notes. 3D Surface Creation
, Training Course Notes Work Volume and Work Planes...........................1 Overview..........................................1 Work Volume....................................1 Work Plane......................................1
More informationIJMH - International Journal of Management and Humanities ISSN:
EXPERIMENTAL STRESS ANALYSIS SPUR GEAR USING ANSYS SOFTWARE T.VADIVELU 1 (Department of Mechanical Engineering, JNTU KAKINADA, Kodad, India, vadimay28@gmail.com) Abstract Spur Gear is one of the most important
More informationLearning Module 8 Shape Optimization
Learning Module 8 Shape Optimization What is a Learning Module? Title Page Guide A Learning Module (LM) is a structured, concise, and self-sufficient learning resource. An LM provides the learner with
More informationIn-plane principal stress output in DIANA
analys: linear static. class: large. constr: suppor. elemen: hx24l solid tp18l. load: edge elemen force node. materi: elasti isotro. option: direct. result: cauchy displa princi stress total. In-plane
More informationME 442. Marc/Mentat-2011 Tutorial-1
ME 442 Overview Marc/Mentat-2011 Tutorial-1 The purpose of this tutorial is to introduce the new user to the MSC/MARC/MENTAT finite element program. It should take about one hour to complete. The MARC/MENTAT
More informationModule 3: Buckling of 1D Simply Supported Beam
Module : Buckling of 1D Simply Supported Beam Table of Contents Page Number Problem Description Theory Geometry 4 Preprocessor 7 Element Type 7 Real Constants and Material Properties 8 Meshing 9 Solution
More informationWorkshop 15. Single Pass Rolling of a Thick Plate
Introduction Workshop 15 Single Pass Rolling of a Thick Plate Rolling is a basic manufacturing technique used to transform preformed shapes into a form suitable for further processing. The rolling process
More informationCourse in ANSYS. Example0410. ANSYS Computational Mechanics, AAU, Esbjerg
Course in Example0410 Example Frame 2D Objective: Compute the harmonic response Tasks: Perform a modal analysis Display the mode shapes Perform a harmonic analysis Topics: Topics: Start of analysis, Element
More informationSolidworks 2006 Surface-modeling
Solidworks 2006 Surface-modeling (Tutorial 2-Mouse) Surface-modeling Solid-modeling A- 1 Assembly Design Design with a Master Model Surface-modeling Tutorial 2A Import 2D outline drawing into Solidworks2006
More informationCustomized Pre/post-processor for DIANA. FX for DIANA
Customized Pre/post-processor for DIANA FX for DIANA About FX4D for DIANA FX4D is a general purpose pre/post-processor for CAE simulation. FX4D has been specialized for civil/architectural applications.
More informationGroup 5 James Pacey, Ray Brown, Brent Sutherland
Group 5 James Pacey, Ray Brown, Brent Sutherland Definition: To model a constant velocity birfield axle joint and shaft, and perform a stress analysis on the birfield Objectives: Gain further CAD experience
More informationFuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
More information3DEXPERIENCE 2017x FINITE ELEMENT ESSENTIALS IN SDC USING SIMULIA/CATIA APPLICATIONS. Nader G. Zamani
Nader G. Zamani FINITE ELEMENT ESSENTIALS IN 3DEXPERIENCE 2017x USING SIMULIA/CATIA APPLICATIONS SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
More informationChapter 3. Thermal Tutorial
Chapter 3. Thermal Tutorial Tutorials> Chapter 3. Thermal Tutorial Solidification of a Casting Problem Specification Problem Description Prepare for a Thermal Analysis Input Geometry Define Materials Generate
More informationQuarter Symmetry Tank Stress (Draft 4 Oct 24 06)
Quarter Symmetry Tank Stress (Draft 4 Oct 24 06) Introduction You need to carry out the stress analysis of an outdoor water tank. Since it has quarter symmetry you start by building only one-fourth of
More informationANSYS EXERCISE ANSYS 5.6 Temperature Distribution in a Turbine Blade with Cooling Channels
I. ANSYS EXERCISE ANSYS 5.6 Temperature Distribution in a Turbine Blade with Cooling Channels Copyright 2001-2005, John R. Baker John R. Baker; phone: 270-534-3114; email: jbaker@engr.uky.edu This exercise
More informationIntroduction to Computer Aided Engineering: Solidworks and Cosmosworks using CosmosXpress
Introduction to Computer Aided Engineering: Solidworks and Cosmosworks using CosmosXpress Open SolidWorks Tutorial written by Jerry Dutreuil Professor Frank Fisher Stevens Institute of Technology Last
More informationCATIA V5 FEA Tutorials Release 14
CATIA V5 FEA Tutorials Release 14 Nader G. Zamani University of Windsor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com CATIA V5 FEA Tutorials 2-1 Chapter 2 Analysis
More informationSuper Elastic Alloy Eyeglass Frame Design Using the ANSYS Workbench Environment
Super Elastic Alloy Eyeglass Frame Design Using the ANSYS Workbench Environment Peter R. Barrett, P.E. Computer Aided Engineering Associates Inc. Patrick Cunningham Computer Aided Engineering Associates
More informationComputational Simulation of Cylindrical Pressure Loading
Computational Simulation of Cylindrical Pressure Loading MEG 795 Special Topics: Energy Methods II Presented By: Nallani Gopi Nov 20, 2003 Department of Mechanical Engineering University of Nevada,Las
More informationMiddle East Technical University Mechanical Engineering Department ME 413 Introduction to Finite Element Analysis Spring 2015 (Dr.
Middle East Technical University Mechanical Engineering Department ME 413 Introduction to Finite Element Analysis Spring 2015 (Dr. Sert) COMSOL 1 Tutorial 2 Problem Definition Hot combustion gases of a
More informationCourse in ANSYS. Example0153. ANSYS Computational Mechanics, AAU, Esbjerg
Course in Example0153 Example Offshore structure F Objective: Display the deflection figure and von Mises stress distribution Tasks: Import geometry from IGES. Display the deflection figure? Display the
More informationCATIA Surface Design
CATIA V5 Training Exercises CATIA Surface Design Version 5 Release 19 September 2008 EDU_CAT_EN_GS1_FX_V5R19 Table of Contents (1/2) Creating Wireframe Geometry: Recap Exercises 4 Creating Wireframe Geometry:
More informationGlider. Clay. Fig. 1 Side face. Step 5. In the Convert Entities Property Manager: click side face, Fig. 3 click OK twice, Fig. 3. Fig. 3.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. Step 2. Click the side face of the Fuselage,
More informationTUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.
TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.
More informationDMU Engineering Analysis Review
Page 1 DMU Engineering Analysis Review Preface Using This Guide Where to Find More Information Conventions What's New? Getting Started Inserting a CATAnalysis Document Using DMU Space Analysis From CATAnalysis
More informationCold Drawn Tube. Problem:
Cold Dawn Tube Poblem: An AISI 1 cold-dawn steel tube has an ID of 1.5 in and an OD of 1.75 in. What maximum extenal pessue can this tube take if the lagest pincipal nomal stess is not to exceed 8 pecent
More information