EPROM Replacement Instructions for Sprint ; Controller Assembly. and Replacement Instructions for Sprint Controller Assembly
|
|
- Lorena Thompson
- 5 years ago
- Views:
Transcription
1 Sprint EPROM and Controller Replacement Instructions Page 1 EPROM Replacement Instructions for Sprint ; Controller Assembly Service Kit P/N and Replacement Instructions for Sprint Controller Assembly Service Kit P/N Introduction This publication contains instructions for the following two service kits: Sprint Controller IReplacement Kit, which contains one complete Sprint Controller Assembly, P/N Controller Assembly Reference Drawing: P/N Sprint Controller EPROM Replacement Kit, which contains: Six EPROMs, labeled1 as follows: MEDIA NUMBER l MEDIA NUMBER 2 MEDIA NUMBER 3 MEDIA NUMBER 4 MEDIA NUMBER 5 MEDIA NUMBER 7 One Electrostatic Discharge (ESD) wrist strap, One EPROM insertion tool, and One EPROM extraction tool Controller Assembly Reference Drawings: P/N and P/N Tools Required The tools required to install these kits are: l/4-in. open-end vvrench small flathead screwdriver CQ No&on Corporation &212 Issued 2l94 P/N A
2 Page 2 Sprint EPROM and Controller Replacement Instructions 2. Safety Precautions Before performing either replacement procedure, remove all power from the system and lock out external power to the electrical cabinet. ; WARNING: Failure to lock out external power to the electrical cabinet may present a serious shock hazard. The input terminal block remains energized with the power OFF. CAUTION: Static electricity can damage EPROMs and boards. Before handling or transporting any board or EPROM, put on the grounded electrostatic discharge (ESD) wrist strap supplied with this kit. For maximum protection, work on a grounded ESD surface. 3. Recording Your Controller User Settings If when you replace the existing controller or option board EPROMs, the user settings will be lost ancl reset to the Nordson defaults. Therefore, after replacing either the controller or the EPROMs, you will need to have available the Table 4.1 Default Settings for OmniScan Control System from section 4 of your applicator system manual so that you can re-enter this data. These are the pages where you entered data on your initial setup. Note: If you did not previously record your user settings, you must go through the menus to get this information. This time make sure that you record these settings for future use. Refer to the part of these instructions that apply to your kit. 4. Replacing the Controller Assembly The following two procedures describe how to remove the existing controller assembly and install a new controller assembly. If you are just replacing EPROMs in an existing controller, go to the EPROM Replacement procedure described later in this document. Once the new assembly is installed, you are then referred to a procedure describing how to check installation and configure software. Removing the Old Con troller Assembly 1. Move the melter circuit breaker to the OFF position. 2. Disconnect and lock out the input power to the melter main circuit breaker. Refer to Figure 1. Figure 1. Locking out powor PIN A Nordson Corporation 1994 Issued 2fQ4
3 Sprint EPROM and Controller Replacement Instructions Page 3 Removing the Old Controller Assembly (contd.) 3. Open the melter cabinet door and locate the controller. A t CAUTION: Wear the grounded wrist strap during this procedure. F:ailure to wear the grounded wrist strap may result in damage to the boards. 4. Ground the wrist strap and put it on your wrist. 5. Refer to Figure 2 and loosen the two lower screws (1) at the bottom sides of the protective cover (3). Figure 2. Removing protective cover 1. Lower Screws 2. Upper Screws 3. Protective Cover 6. While holding the protective cover (3), remove the two upper screws (2), and pull the cover off, clearing all boards. Then set it aside until you install the new controller assembly. 0 Nordson Corporation P/N A All Riqhts Reserved Issued 2l94
4 Page 4 Sprint EPROM and Con troller Replacement Instructions Removing the Old Controller Assembly (contd.) 7. Kefer to Figure 3 and diisconnect all external cables and connectors from the controller. ; Figure 3. Disconnecting controller s external cables and connectors 8. Move to the front of the cabinet door and, while supporting the entire controller assembly, remove the six screws that secure the controller s front panel to the door. 9. With all the screws removed, tilt the assembly slightly forward so that you can grasp the front panel, then carefully remove it from the cabinet door. IO. Set the entire assembly aside and, when time permits, contact your NordsonB representative or customer service for return procedures. 11. This completes removal of the old controller assembly. Proceed with lnsfalling the New Controller Assembly described next. Ins tailing the New Con troller Assembly 1. Remove the new controller from its packing material and inspect it for loose or broken items, etc. If damage is evident, contact your NordsonB representative or customer service before proceeding. 2. Move to the front of the cabinet door and, while supporting the entire controller assembly, insert the rear portion through the door opening. While holding the front panel against the supporting edge, install the six screws that secure the controller s front panel to the door. 3. Move to the rear of the cabinet door and connect all external cables and connectors to the controller (figure 3) that were removed from the original assembly. 4. Mount the old protective cover onto the new controller assembly as shown in figure 2 using four screws. 5. This completes installation of the new controller assembly. Proceed with Checking Installation and Configuring Software described later in this document. P/N A Issued 2/94 Q Nordson Corporation 1994
5 Sprint EPROM and Con troller Replacement Instructions Page 5 5. EPROM Replacement If you are installing a complete Sprint Controller Assembly (Kit P/N ), skip these instructions. This procedure is only for replacing the EPROMs on boards of an existing controller, and involves: gaining access to the controller boards, removing the boardls from the controller, replacing the board EPROMs, and reinstalling the boalrds Gaining Access to Con troller Boards 1. Move the melter circuit breaker to the OFF position. 2. Disconnect and lock out the input power to the melter main circuit breaker. Refer to Figure 4. Figure 4. Locking out power 3. Open the melter cabinet door and locate the controller. A t CAUTION: Wear the grounded wrist strap during this procedure. Failure to wear the grounded wrist strap may result in damage to the boards. 4. Ground the wrist strap and put it on your wrist. 6 Nordson Corporation 1994 All Rinhts Resewed Issued 2l94 P/N A
6 Page 6 Sprint EPROM and Con troller Replacement Instructions Gaining Access to Controller Boards (contd.) 5. Refer to figure 5 and loosen the two lower screws (1) at the bottom sides of the protective cover (3). Figure 5. Removing protective cover 1. Lower Screws 2. Upper Screws 3. Protective Cover 6. While holding the protective cover (3), remove the two upper screws (2), and pull the cover off, clearing all boards. Then set it aside. 7. Refer to Figure 6 and disconnect all external cables and connectors from the controller. Figure 6. Disconnecting controller s external cables and connectors P/N A Nordson Corporation 1994 Issued 2194
7 Sprint EPROM and Con troller Replacement Instructions Page 7 Rem0 ving Con troller Option Boards 1 Refer to Figure 7 and remove the outer three circuit boards by removing the screws and standoffs between them using a screwdriver and a l/4-in. wrench. Figure 7. Removing boards 1. l/o Option Board 2. Analog Option Board 3. RS23;? Option Board 4. ACU (main) Board Note: Referring to Figure 7, remove the circuit boards in the following order: the I/O (1), the analog input board (2), and the RS-232 (3). The ACU board (4) does not have to be removed. 2. Place the three boards on the grounded ESD surface, and continue with Replacing Board EPROMs described next. Replacing Board EPROMs A CAUTlONWear t the grounded wrist strap during this procedure. Failure to wear the grounded wrist strap may result in damage to the boards. This kit contains six EiPROMs. Install them on the following boards: ACU board MEDIA NUMBER 1 MEDIA NUMBER 2 MEDIA NUMBER 3 I/O board RS-232 board MEDIA NUMBER 4 MEDIA NUMBER 5 Analog board MEDIA NUMBER 7 1. Refer to drawing sheet 1 and locate the EPROMs labeled MEDIA NUMBEFt 1,2, and 3 on the ACU board. 2. Refer to drawing sheet 1 and locate the EPROM labeled MEDIA NUMBEFl4 on the I/O board. Q Nordson Corporation 1994 All Riqhts Reserved issued 2/94 P/N A
8 Page 8 Sprint EPROM and Controller Replacement Instructions Replacing Board EPROMs 3. Refer to drawing sheet 2 and locate the EPROM labeled (con td.) MEDIA NUMBER 5 on the RS-232 board. ; 4. Refer to drawing sheet 2 and locate the EPROM labeled MEDIA NUMBER 7 on the Analog board. 5. Except for MEDIA NUMBER 3 (on the ACU board), remove all the other EPROMs as follows: a. Push the locking tab in the direction of the arrow labeled OPEN to release the EPROM from its socket. Refer to Figure 8. Figure 8. EPROM locking tab (pictured in locked (ACT) position) b. Remove the EPROM by grasping it with the extraction tool. Pull gently from the board at a 90 angle. See Figure 9. Figure 9. Grasping EPROM chip using extracting tool 6. MEDIA NUMBER 3 dosle not have a locking tab. Just use the chip extraction as follows to remove it: P/N A Issued Nordson Corporation 1994 All Riqhts Reserved
9 Sprint EPROM and Controller Replacement Instructions Page 9 Replacing Board EPROMs (con td.) - a. As shown in Figure 9, align the tool above the EPROM and firmly grasp the ends of the chip. ; b. Pull the EPROM gently from the board at a 90 angle. 7. Remove the new EPROMs from their protective bags. Note: Observe the MIEDIA NUMBER of each chip. The EPROMs must be inserted in the correct location on the boards for proper equipment operation. Refer to dr awing sheets 1 and Insert each EPROM (except MEDIA NUMBER 3) in its correct socket as follows: a CAUTION: l3e sure that you insert the EPROMs correctly in I their respective socket, see Figure 10. If they are installed 0 wrong they will be damaged when power is applied to the controller. Figure 10. Correct orientation of EPROM chip placement in socket (Notch is closed to top of board.) 7. Pin 7 2. Top of board 3. Notch Location a. Align the notch of the socket with the notch in the EPROM. b. Make sure that each of the pins lines up correctly with the socket holes. Misalignment could cause one of the pins to bend. c. Ensure that the pins are fully bottomed in the socket. d. Lock the EPROM in its socket by pushing the tab in the direction of the arrow marked ACT. 0 Nordson Corporation Issued 2/94 P/N A
10 Page 10 Sprint EPROM and Controller Replacement Instructions Replacing Board EPROMs (con td.) 9. Insert MEDIA NUMBER 3 as follows: a. Holding the EPROM in the insertion tool, alignthe chip above the socket, making sure thlat each of the pins line up correctly with the socket holes. Misalignment could cause one of the pins to bend. Refer to Figure 11. Figure II. Aligning MEDIA NUMBER 3 with socket using insertion too/ b. Insert the EPROM into the socket with insertion tool. c. Press the EPROM firmly and evenly into the socket. 10. This completes EPROM installation. Continue with Checking the Board Switch Settings described next. Checking Option Board Switch Settings Check the switch settings on the I/O, Analog, and RS-232 boards before installing them. The switches should be set as shown in drawing After verifying for correct switch settings, go to Reinstalling Controller Boards described next. Reins tailing Con troller Option Boards 1. Replace the I/O, Analog, and RS-232 boards as shown in Figure 7. CAUTION: SometiImes the standoffs used for mounting the boards have been shipped with washers for use between the standoff and the board; however, it has been found that this slight spacing distance that the washer adds can cause problems with proper mating of the board s 64-pin connector Jl. Therefore, be sure not to use any washers between the board and standoff when reinstalling boards. Inspect the 64-pin connector Jl to ensure that all pins mate correctly with the corresponding socket. View the mated connector from several angles to ensure correct mating. 2. Reconnect all ribbon cables and connectors as shown in Figure 6. PM A Nordson Corporation 1994 Issued 2l94 All Rights Resewed
11 Sprint EPROM and Con troller Replacement Instructions Page 11 Reins tailing Con troller Option Boards (con td.) 3. Remount the protective cover as shown in Figure This completes installation of the boards. Proceed with Checking installation and CcvViguring Software described next. 6. Checking Ins talla tion and Configuring Software This procedure serves as a final operational check for the controller and should be performed after either installing a new option board and/or new EPROMs, or a new complete controller assembly. I. Restore external plower. The unit will now automatically perform power up self-test.. When the self test is finished and if no problems were encountered, the controller display begins monitoring the configured parameters, or displays the default present configuration code menu. Service Activity Performed and Software Version Option board replaced and its software version is same as that on old controller. Option board replaced and its software version is newer than that on old controller. Thus, controller software (EPROM) was replaced to match new board. Entire controller was replaced. 2. Depending on the software version and the service activity performed, Table I describes what action you should take next: Table 1. Action Required for Service Activity Performed Service Activity Needed Unit will resume normal operation. No further action required. Memory will be cleared and you must re-enter configuration code and all user settings recorded prior to performing the replacement operation described in these instructions. Continue with Re-entering Configuration Code Method 7 described below. Memory will contain factory default codes. You must re-enter configuration code and all user settings recorded prior to performing the replacement operation described in these instructions. Continue with Re-entering Configuration Code Method 2 described below. Re-en tering Configuration Code Method I After restoring power to the controller the default present configuration code menu shown below is displayed. This code is just a representation of the content of this [menu and is not your actual configuration code. PRESENT CONFIG CODE: 3400-lAA52/ 3400-l AA52/ 1. Enter 4011 as the! configuration code for your Sprint applicator. Then press ENTER until the controller resumes normal operation. Note that the dash (-) must be included in the configuration code. 2. The start-up software will run and the unit will resume normal operation using factory default parameters. You now need to re-enter your user settings, so go to Re-entering User Settings described at the end of this document. Q Nordson Corporation Issued 2/94 PIN A
12 Page 12 Sprint EPROM and Controller Replacement Instructions Re-en tering Configuration Code Method 2 Note: This method is only to be performed when you replaced the entire controller. Begin at the Run Mode with Operator Menu and access the Factory Menu as follows: 1. Press number 1, then 2, then 7. The display will show the following: ACCESS CODE: XXXX CALL NORDSON FOR PASSWORD: **** I 2. XxXx will be a four digit number. This number corresponds to the first of a pair of four-digit numbers shown in the password list in Table 2. Table 2. Access Code, Password Pairs I I I I IO i I :: :;:i 1 ii:: I :347 I I Select the CLR-RAM function using the touchpad. A warning message will appear and a YES/NO confirmation will be requested as shown below: Note: If you mistakenly choose the wrong function and do NOT want to change it, press the CANCEL touchpad. The factory menu will again be displayed. Either choose the function that you intend to change, or press CANCEL again if no changes are desired. The CLR-RAM function re-initializes the battery-backed RAM. When the battery-backed RAM is re-initialized, the configuration code and all user-defined values are reset to factory defaults. CLEAR ALL RAM VALUES: NO ARE YOU SURE? NO P/N A tssued Nordson Corporation 1994
13 Sprint EPROM and Controller Replacement Instructions Page 13 Re-en tering Configuration Code Method 2 (contd.) 5. Use the arrow keys to select YES and press ENTER. The CLEAR RAM function then displays the applicator s default present configuration code. This code is just a representation of the content of this menu and not your actual configuration code. PRESENT CONFIG CODE: 3400-I AA52/ 3400-l AA52l 6. Enter 4011 as the configuration code for your Sprint applicator. Then press ENTER until the controller resumes normal operation. Note that the dash (-) must be included in the configuration code. 7. The start-up software will run and the unit will resume normal operation using factory default parameters. You now need to re-enter your user settings as described next. Re-en tering User Settings Refer to the Tab/e 4. I Default Setfings for OnmiScan Control System from section 4 of your applicator system manual that you were told to record earlier and re-enter the respective parameters by selecting the appropriate menu item and changing the setting to those on your list. If necessary, refer to th,e Operating Instructions, Section 4 of your applicator manual for instructions on entering or changing settings. Once these data are entered the unit will start running from these new settings. 8 Nordson Corporation Issued 2l94 P/N A
14 Page 14 Sprint EPROM and Con troller Replacement Instructions P/N A No&on Corporation 1994 issued 2i94
Replacement Instructions for Controller Assembly MC0 Option Board
MC0 Option Board Replacement Instructions Page 1 Replacement Instructions for lomniscan@ Controller Assembly MC0 Option Board Service Kit P/N 166 773 1. Introduction This publication contains instructions
More informationEPROM Replacement for Contrbl Systems
EPROM Replacement 1 EPROM Replacement for OmniScan@ Contrbl Systems Important 0 Before starting, read all instruction sheets that have been provided with your service kit It is recommended that you use
More informationPro-Flo System Digital Controller EPROM Upgrade
Instruction Sheet P/N Pro-Flo System Digital Controller EPROM Upgrade 1. Introduction See Figure 1. The EPROM chips are designed to upgrade your Pro-Flo system digital controller for expanded operation.
More informationEMC 10T "CE" Mechanical Upgrade Procedure
EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationReplacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly
Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,
More information256 Kbytes (1771-DRS) 1 Mbyte (1771-DRS1) 4 Mbytes (1771-DRS4) Installation Data
Installation Data You can add static RAM memory to your control coprocessor main module to expand user memory. The RAM single inline memory module (SIMM) is available in the following sizes: 256 Kbytes
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0597 Kepco KIT 219-0597 contains the PROMs used to upgrade the firmware for BOP
More informationReplacement Instructions. Backplane PCA for the HP Router 650
Replacement Instructions Backplane PCA for the HP Router 650 Copyright Hewlett-Packard Company 1994. All rights reserved. Publication Number 5962-8369 Edition 1, August 1994 Printed in USA This guide provides
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationReplacing the Hardware Configuration Option EPROM on the 1822
MPMS Service Note 1014-806 Replacing the Hardware Configuration Option EPROM on the 1822 When you install an MPMS option, you will use these procedures to replace the hardware configuration option EPROM
More informationEMC 10/4 "CE" Mechanical Upgrade Procedure
EMC 10/4 "CE" Mechanical Upgrade Procedure Kit Part Number: 009663-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationFC-25/50DA Main Circuit Board Replacement Product Installation Document
FC-25/50DA Main Circuit Board Replacement Product Installation Document Document 51875 Rev A 10/12/01 ECN 01-506 This Product Installation Document outlines the replacement of the Main Circuit Board for
More informationEPX Touchscreen and Display Replacement Assemblies
EPX Touchscreen and Display Replacement Assemblies This document describes the procedures required to replace the touchscreen and display assembly in the EPX BZK-08T7 kit. The following procedures are
More informationInstalling and Removing SDRAM and DRAM
CHAPTER 4 This chapter explains how to remove and replace the main memory modules on the network processing engine or network services engine. For the location of the memory module you are replacing, find
More informationP1 PowerStation Backlight Bulb
The P1 PowerStation is designed to allow you to easily replace the backlight bulb without removing the unit from its enclosure. However, CTC recommends that you remove the touch screen completely before
More informationVoice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document
Voice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document Document 50795 Rev B 10/10/01 ECN 01-507 This Product Installation Document outlines the replacement of the Main
More informationReplacing Preamplifier Circuit Boards
Instruction Guide Replacing Preamplifier Circuit Boards Before you begin This instruction sheet applies to the Plexon PBX-series preamplifiers. Use these instructions to expand, replace, or upgrade the
More informationEPROM REPLACEMENT INSTRUCTIONS
MOTION CONTROL ENGINEERING, INC. 11354 WHITE ROCK ROAD RANCHO CORDOVA, CA 95742 TELEPHONE (916) 463-9200 FAX (916) 463-9201 CAR CONTROLLER MAIN PROCESSOR BOARD EPROM REPLACEMENT INSTRUCTIONS 42-02-G002
More informationS200 Series Brushless Servo Drive EPROM Upgrade
KOLLMORGEN www.danahermotion.com S200 Series Brushless Servo Drive EPROM Upgrade AC & DC version of the S200 is shown below in a work area that provides a static free work surface, grounded wrist strap,
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationELECRAFT P3 HIGH-PERFORMANCE PANADAPTER P3SVGA OPTION INSTALLATION AND OPERATING INSTRUCTIONS. Rev B, March 20, 2012
ELECRAFT P3 HIGH-PERFORMANCE PANADAPTER P3SVGA OPTION INSTALLATION AND OPERATING INSTRUCTIONS Rev B, March 20, 2012 Copyright 2012, Elecraft, Inc. All Rights Reserved Contents Introduction... 3 Customer
More informationIntel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide
Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationMicroprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
621 Hunt Valley Circle New Kensington, PA 15068 3015-5547 Tel: 724-334-5000 Revision 4 Fax: 724-334-5001 May 17, 2013 Microprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0621 Kepco KIT 219-0621-(n) contains the parts used to upgrade the firmware for
More informationInstalling and Upgrading Memory and Virtual Private Network Modules
APPENDIX C Installing and Upgrading Memory and Virtual Private Network Modules This chapter tells how to install or upgrade memory and how to install a Virtual Private Network (VPN) module in your Cisco
More informationInstalling a New Solo 1150 Hard Drive
Installing a New Solo 1150 Hard Drive This package includes a new hard drive kit for your Solo 1150 notebook computer and these printed instructions. Tools you need You will need a small Phillips screwdriver
More informationJob Aid: Replacing the Field Replaceable Units (FRUs) for the Avaya G430 Media Gateway
Job Aid: Replacing the Field Replaceable Units (FRUs) for the Avaya G430 Media Gateway! Important: Important: Always check the Avaya Support Website for Product Support Notices at http:// support.avaya.com
More informationINSTALLATION INSTRUCTIONS
TT-40 9/0 INSTALLATION INSTRUCTIONS Original Issue Date: 9/0 Model: Automatic Transfer Switches Equipped with the Programmable Controller Market: ATS Subject: External Battery Supply Module Kit GM69-KP
More informationSonnet AV/HPV Card Video Adapter Kit
Installation Instructions for Power Macintosh 7100 and 8100 Adapter Kit Inventory Before installing the AV/HPV Card Video Adapter, you will require the following items (Figure 1): Included with adapter
More informationUser Guide. Intel NUC7 Home, a Mini PC with Windows 10 NUC7i5BNKP. Intel NUC7 Enthusiast, a Mini PC with Windows 10 NUC7i7BNKQ
Intel NUC7 Home, a Mini PC with Windows 10 NUC7i5BNKP Intel NUC7 Enthusiast, a Mini PC with Windows 10 NUC7i7BNKQ User Guide 1 Before You Begin CAUTION The procedures in this guide assume familiarity with
More informationV5420 Host Card Upgrade Kit for R3082D Quick Start Guide
Quick Start Guide Upgrade kit contents The table below shows the contents of the V5420 Host Card Upgrade Kit (components are not shown to scale). Part Function Pieces V5420 Host Card 1 Host card bracket
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationUser Guide for NUC7i3DNHNC. Intel NUC7 Business, a Mini PC with Windows 10 NUC7i3DNHNC. User Guide
Intel NUC7 Business, a Mini PC with Windows 10 NUC7i3DNHNC User Guide 1 Before You Begin CAUTIONS The steps in this guide assume you re familiar with computer terminology and with the safety practices
More informationPS/IO Circuit Board Retrofit
S&C 6800 Series Automatic Switch Controls PS/IO Circuit Board Retrofit Table of Contents Section Page Introduction Qualified Persons.... 2 Read this Instruction Sheet.... 2 Retain this Instruction Sheet....
More informationRevision History E F G H J K Revision Description: K > Allegion Rebranding.
Notes: Enter any notes here. These notes must include: how many sides of the paper are printed ink color (usually black, may also be one or two specific colors, such as a Pantone value, or 17.000 8.500
More informationInstallation Note. Source Attenuators and Bias Tees Upgrade Kit. For E8362B/C PNA Series Microwave Network Analyzers. Network Analyzer Model Number
Installation Note Source Attenuators and Bias Tees Upgrade Kit For E8362B/C PNA Series Microwave Network Analyzers Network Analyzer Model Number Upgrade Kit Part Number E8362B/C E8362-60115 Agilent Part
More informationPrint Mechanism Maintenance Kit
Print Mechanism Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the print mechanism maintenance kit in the following printers: ZT0 ZT0 ZT0 Read
More informationAC300/AC400 SERIES DYNAMIC BRAKING and ADDITIONAL FORM C RELAY. INSTALLATION INSTRUCTIONS Document Number:
Minarik Variable Speed AC Motor Drives AC300/AC400 SERIES DYNAMIC BRAKING and ADDITIONAL FORM C RELAY INSTALLATION INSTRUCTIONS Document Number: 250-0297 These instructions apply to models rated: 7.5 25
More informationUser Guide. Intel NUC 8 Business, a Mini PC with Windows 10 NUC8i7HNKQC. Intel NUC 8 Enthusiast, a Mini PC with Windows 10 NUC8i7HVKVA
Intel NUC 8 Business, a Mini PC with Windows 10 NUC8i7HNKQC Intel NUC 8 Enthusiast, a Mini PC with Windows 10 NUC8i7HVKVA User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume
More informationMemory Expansion for DriveLogix Controller
Installation Instructions Memory Expansion for rivelogix ontroller!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work
More informationUser Guide for NUC8i5BEK, NUC8i3BEK. Intel NUC Kit NUC8i5BEK Intel NUC Kit NUC8i3BEK. User Guide
Intel NUC Kit NUC8i5BEK Intel NUC Kit NUC8i3BEK User Guide 1 Before You Begin CAUTIONS The steps in this guide assume you re familiar with computer terminology and with the safety practices and regulatory
More informationIntel NUC Kit DC53427HYE User Guide. Intel NUC Kit DC53427HYE
Intel NUC Kit DC53427HYE User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers and with the safety
More informationMaintaining E-Series Routers
Maintaining E-Series Routers 9 This chapter lists the tools, items, and steps needed for installing and uninstalling E-series components. Other maintenance procedures must be performed by an authorized
More informationIntel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK. User Guide
Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationKeysight Second Source, Combiner, and Mechanical Switches Upgrade Kit
Keysight Second Source, Combiner, and Mechanical Switches Upgrade Kit To Upgrade PNA-X N5241A, N5242A, or N5249A Option 419 to Option 423 Upgrade Kit Order Number: N5241AU- 927, N5242AU- 927, and N5249AU-
More informationUser Guide. Intel NUC 7 Home, a Mini PC with Windows 10 NUC7i5BNKP. Intel NUC 7 Enthusiast, a Mini PC with Windows 10 NUC7i7BNKQ
Intel NUC 7 Home, a Mini PC with Windows 10 NUC7i5BNKP Intel NUC 7 Enthusiast, a Mini PC with Windows 10 NUC7i7BNKQ User Guide 1 Before You Begin CAUTION The steps in this guide assume you re familiar
More informationZ Series and S4M Ribbon Take-Up Spindle Maintenance Kit
Z Series and SM Installation Instructions This kit includes the parts and documentation necessary to install the Ribbon Take-Up Spindle Maintenance Kit into the following printers: Z Series (ZM, Z6M, ZMplus,
More informationSmart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction
Smart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction Electronics Module (Part number 51404208 503, -513) Document Form: 34-SM-33-01 Effective: 09-01 Supersedes: 34-SM-33-01,
More informationInstalling the upgrade memory kit in the G450 and G430 Media Gateway
Installing the upgrade memory kit in the G450 and G430 Media Gateway Important: Always check the Avaya Support Website for Product Support Notices at http://www.avaya.com/ support and select Communication
More informationIon Memory Upgrade. Visit the AMI Entertainment Web site PM
Ion Memory Upgrade Visit the AMI Entertainment Web site http://www.meritgames.com PM0672-04 COPYRIGHT 2011 AMI ENTERTAINMENT NETWORK, INC. Ion Memory Upgrade CONTENTS: QTY PART NUMBER DESCRIPTION 1 EC0146-06
More informationUser Guide. Intel NUC 8 Enthusiast, a Mini PC with Windows 10 NUC8i7BEKQA. Intel NUC 8 Home, a Mini PC with Windows 10 NUC8i5BEKPA
Intel NUC 8 Enthusiast, a Mini PC with Windows 10 NUC8i7BEKQA Intel NUC 8 Home, a Mini PC with Windows 10 NUC8i5BEKPA User Guide 1 Before You Begin CAUTIONS The steps in this guide assume you re familiar
More informationAllen-Bradley Motors
Installation Instructions Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers Purpose Firmware Update Kit Contents Hardware and Software Requirements This
More informationElecraft K3 KREF3 Output Level Modification
Elecraft K3 Revision A, September 15, 2015 Copyright 2015, Elecraft, Inc. All Rights Reserved Introduction This modification increases the output levels from the KREF3 Reference Oscillator to provide proper
More informationIntel NUC7 Home, a Mini PC with Windows 10 NUC7i3BNHXF. Intel NUC7 Home, a Mini PC with Windows 10 NUC7i5BNHXF
Intel NUC7 Home, a Mini PC with Windows 10 NUC7i3BNHXF Intel NUC7 Home, a Mini PC with Windows 10 NUC7i5BNHXF Intel NUC7 Enthusiast, a Mini PC with Windows 10 NUC7i7BNHXG User Guide 1 Before You Begin
More informationUser Guide for NUC7CJYSAL. Intel NUC 7 Essential, a Mini PC with Windows 10 NUC7CJYSAL. User Guide
Intel NUC 7 Essential, a Mini PC with Windows 10 NUC7CJYSAL User Guide 1 Before You Begin CAUTIONS The procedures in this guide assume familiarity with the general terminology associated with personal
More informationHow to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit
Instructional Video Series How to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit Skill Level: Challenging Time to Complete: Approximately 45 Minutes Required
More informationAfter completing this chapter, you will meet these objectives:
3.0 Introduction Assembling computers is a large part of a technician's job. As a technician, you will need to work in a logical, methodical manner when working with computer components. As with any learned
More informationRemoving and Installing the ISA and the ISM
CHAPTER This chapter describes how to remove the ISA or ISM from supported platforms and also how to install a new or replacement ISA or ISM. This chapter contains the following sections: Handling the
More informationAutoScan to MultiScan Replacement Kit
Instruction Sheet P/N AutoScan to MultiScan Replacement Kit WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationA TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address
Requirements A TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address Power Up A Reader with an Ethernet adaptor installed and the network cable
More informationGateway Profile 4 service guide
Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................
More informationPC9/P9 CPU Card Replacement
Introduction These instructions explain how to replace the CPU card in the PC9 Industrial PC or the P9 PowerStation. They include steps for disassembling the unit, removing the old CPU card, installing
More informationT9 EPP KEYPAD FIELD UPGRADE
T9 EPP KEYPAD FIELD UPGRADE TDN 07103-00237 July 1, 2014 Corporate Headquarters 21405 B Street Long Beach, MS 39560 Phone: (800) 259-6672 Fax: (228) 868-9445 COPYRIGHT NOTICE 2014 Triton. All Rights Reserved.
More informationMODULUS 21 Power Distribution Unit (PDU) Replacement. Overview A. Introduction
Page 1 of 16 MODULUS 21 Power Distribution Unit (PDU) Replacement Overview Introduction This notice explains how to replace the AC Power Distribution Unit (PDU), also known as a Power Distribution Assembly
More informationIntel NUC Kit D54250WYKH & D34010WYKH User Guide. Intel NUC Kit D54250WYKH Intel NUC Kit D34010WYKH User Guide
Intel NUC Kit D54250WYKH Intel NUC Kit D34010WYKH User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationIntel NUC Kit DN2820FYKH User Guide. Intel NUC Kit DN2820FYKH User Guide
Intel NUC Kit DN2820FYKH User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers and with the safety
More informationMotion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure
Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure 2008 Motion Computing, Inc. All rights reserved. This document contains information protected by copyright. No part of this document may be reproduced
More informationIntel NUC Kit NUC7i3BNHX1 with Intel Optane Memory. Intel NUC Kit NUC7i5BNHX1 with Intel Optane Memory
Intel NUC Kit NUC7i3BNHX1 with Intel Optane Memory Intel NUC Kit NUC7i5BNHX1 with Intel Optane Memory Intel NUC Kit NUC7i7BNHX1 with Intel Optane Memory User Guide 1 Before You Begin CAUTIONS The procedures
More informationSerial ATA Hot Swap Drive Cage Upgrade Kit for: Intel Server Chassis SC5200 Intel Server Chassis SC5250-E
Serial ATA Hot Swap Drive Cage Upgrade Kit for: Intel Server Chassis SC5200 Intel Server Chassis SC5250-E A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/Products Order Number:
More informationIntel NUC Kit NUC7i7BNH Intel NUC Kit NUC7i5BNH Intel NUC Kit NUC7i3BNH
Intel NUC Kit NUC7i7BNH Intel NUC Kit NUC7i5BNH Intel NUC Kit NUC7i3BNH User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated
More informationMaintaining the ERX System
7 This chapter describes the procedures that you must perform to maintain the ERX system and its components. Other maintenance procedures must be performed by an authorized Juniper Networks technician.
More informationInstalling the Cisco ADE 2130 and 2140 Series Appliance Hardware Options
CHAPTER 4 Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options This chapter provides instructions for installing, replacing, and removing various hardware options in your Cisco ADE
More informationPowerFlex DC Drive - Frame A Switching Power Supply Circuit Board
Installation Instructions PowerFlex DC Drive - Frame A Switching Power Supply Circuit Board ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should plan or implement
More informationInstallation Note. Configurable Test Set Upgrade Kit. For PNA Series RF Network Analyzers (E8801A, E8802A, and E8803A) Network Analyzer Model Number
Installation Note Configurable Test Set Upgrade Kit For PNA Series RF Network Analyzers (E8801A, E8802A, and E8803A) Network Analyzer Model Number Upgrade Kit Part Number E8801A, E8802A, E8803A E8801-60103
More informationE2460GS Oscilloscope Upgrade Kit
Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationThank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com.
Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com. Please check out our ebay auctions for more great deals on Factory Service Manuals: servicemanuals4u Dell Latitude
More information2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual
2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation
More informationInstallation Instruction VCPRGBGM05 - rev1.5 RGB Interface Harness modification Navigation Radio
Introduction The following instruction procedure is for the RGB interface to a GM 05 Nav Radio as part of the Webasto Product NAVCam Back-up Camera (VCP-0000220). In addition, an installer will need to
More informationGPIB-232CT-A IBCL EPROM Installation Guide
NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide GPIB-232CT-A IBCL EPROM Installation Guide This guide describes how to replace the factory-installed EPROM that comes with your GPIB-232CT-A.
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationNvidia Quadro FX 5600 graphics card and auxiliary power adapter cable installation
Nvidia Quadro FX 5600 graphics card and auxiliary power adapter cable installation HP xw8600 and xw9400 Workstations This document describes how to install an Nvidia Quadro FX 5600 graphics card and an
More information13 MMC for PC Option Modules
Part Number M.1300.8684 MMC for PC Option Modules Manual V3.0 The information in this document is also available in the MMC for PC Hardware Manual. 13 MMC for PC Option Modules 13.1 General The MMC for
More informationReplacing or Upgrading DiskOnChip Memory
Installation Instructions Replacing or Upgrading DiskOnChip Memory Objectives This document describes how to replace or upgrade DiskOnChip flash memory in a RAC6182 Industrial Computer. European Union
More informationIntel NUC Kit NUC6CAYS User Guide
Intel NUC Kit NUC6CAYS User Guide Regulatory Model NUC6CAY 1 Before You Begin CAUTIONS The steps in this guide assume you re familiar with computer terminology and with the safety practices and regulatory
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More informationPlasma Panel Replacement Guide DU-42PX12X
Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be
More informationWarning! To prevent any bodily damage read entire manual before starting.
Warning! To prevent any bodily damage read entire manual before starting. DANGER To prevent possible electrical shock during an electrical storm, do not connect or disconnect cables or station protectors
More informationIntel NUC Kit NUC5i3MYHE & NUC5i5MYHE User Guide. Intel NUC Kit NUC5i3MYHE Intel NUC Kit NUC5i5MYHE User Guide
Intel NUC Kit NUC5i3MYHE Intel NUC Kit NUC5i5MYHE User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationAllen-Bradley Drives. Instructions. (For 6180 Industrial Computers)
Instructions (For 6180 Industrial Computers) This document describes how to remove or install a Pentium processor in the 6180 Industrial Computer. Processor specifications are also provided. The processor
More informationInstallation Note. IF Access Upgrade Kit. For PNA Series Microwave Network Analyzers. Network Analyzer Model Number. Upgrade Kit Part Number
Installation Note IF Access Upgrade Kit For PNA Series Microwave Network Analyzers Network Analyzer Model Number E8361A/C, E8362B/C, E8363B/C, E8364B/C Upgrade Kit Part Number E8362-60116 Agilent Part
More informationIntel NUC 7 Home, a Mini PC with Windows 10 NUC7i3BNHXF. Intel NUC 7 Home, a Mini PC with Windows 10 NUC7i5BNHXF
Intel NUC 7 Home, a Mini PC with Windows 10 NUC7i3BNHXF Intel NUC 7 Home, a Mini PC with Windows 10 NUC7i5BNHXF Intel NUC 7 Enthusiast, a Mini PC with Windows 10 NUC7i7BNHXG User Guide 1 Before You Begin
More informationedrive RAM Battery Alternate Replacement Procedure
edrive RAM Battery Summary This technical note describes the process for replacing the TINI RAM battery with a higher capacity battery. With the edrive turned on, the external battery can be changed without
More informationEquipment (Tools) Needed
www.displayrepairkit.com Display Repair Kit This kit is compatible with all Fluke 80 Series (83, 85, 86, 87, & 88), Matco MD- 88 Fluke 88, and Fluke Kent-Moore J39200 Multimeters. Older Fluke 80 Series
More informationDell XPS M1730 Service Manual
Dell XPS M1730 Service Manual Model PP06XA www.dell.com support.dell.com Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE:
More informationSRP Field Upgrade Installation Instructions
SRP Field Upgrade Installation Instructions 03 November 2004 Part No: 162-00982-00 Revision A01 This document describes installation procedures for upgrading switch route processor (SRP) modules, I/O modules,
More informationReplace the edrive TINI Module and Battery
Product All edrive Configurations Special Information INFORMATION: This service bulletin is for informational purposes only. It is intended for use by Northrop Grumman Cutting Edge Optronics (NG CEO) employees
More informationTD-700 FLUOROMETER SERVICE MANUAL
TD-700 FLUOROMETER SERVICE MANUAL July 1996 CONTENTS Page Section 1 INTRODUCTION 2 Section 2 PRELIMINARY CHECKS 3 Section 3 TROUBLESHOOTING GUIDE 5 A. Lamp (Fluorescent) 5 B. Lamp Heater 7 C. Fan 8 D.
More informationIntel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide. Intel NUC Kit NUC7i7BNH Intel NUC Kit NUC7i5BNH Intel NUC Kit NUC7i3BNH User Guide
Intel NUC Kit NUC7i7BNH Intel NUC Kit NUC7i5BNH Intel NUC Kit NUC7i3BNH User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated
More information