Installation and User Guide. Digidim Remote Control (303) Product description. Switching Lights On/Off using Digidim 303 Remote

Transcription

1 Installaton and User Gude Dgdm Remote Control (0) Product descrpton The Dgdm Remote (0) can be used n conjuncton wth the Dm Sense to modfy the preset lght levels and recall/ store scenes, as well as actvatng ts specal functons (00 h Burn-In, PIR Walk test and Mode Identfcaton). A. LED Indcator (Flashes as each message s transmtted) B. Scene Recall/Confguraton C. n/ff/shft D. Modfer Keys E. Transmtter F. Battery Cover Swtchng Lghts n/ff usng Dgdm 0 Remote To swtch the lghts n or ff:. Pont the remote control at a controller 0 %. Press n/ff/shft key on remote control to swtch the lghts on or off Note: Throughout ths document Controller refers to Dm 0/ Sense and/or Button Panels. Recall Scenes usng Dgdm 0 Remote To recall a scene usng the DIGIDIM remote:. Pont the remote control at a controller. Press scene key,, or to recall scene Modfy Lght Levels usng Dgdm 0 Remote To modfy DALI lght levels usng the DIGIDIM remote:. Pont the remote control at a controller. Press scene Up modfer key to rase DALI lght level. Press scene Down modfer key to lower DALI lght level Note: To store scenes see chapter % DALI 00 % 00 % % To modfy DALI lght levels usng the DIGIDIM remote:. Pont the remote control at a controller. Press scene Up modfer key to rase DALI lght level. Press scene Down modfer key to lower DALI lght level DALI % 00 % 00 % % Helvar Data s subject to change wthout notce.

2 Contents Secton Page Product descrpton Swtchng Lghts n/ff usng Dgdm 0 Remote Recall Scenes usng Dgdm 0 Remote Modfy Lght Levels usng Dgdm 0 Remote Store Scenes usng Dgdm 0 Remote Specal Functons usng Dgdm 0 Remote LED Flash Feedback Techncal Data Helvar Data s subject to change wthout notce.

3 Store Scenes usng Dgdm 0 Remote To store a modfed scene usng the DIGIDIM remote:. Pont the remote control at a controller. H old scene key,, or for 0 seconds to 0 s store scene. Dm Sense LEDs wll flash green f successful. 0 s 0 s 0 s Note: See LED Feedback table on fnal page of ths document for LED nformaton. Specal Functons usng Dgdm 0 Remote Start/Stop 00 hour Burn-In Mode To start or stop Burn-In mode:. Pont the remote control at a controller. Press n/ff/shft key and scene at same tme 0/ Note: Restartng a Burn-In test followng a stop wll cause the 00 hour counter to restart from 0. Use Resume sburn-in Mode to contnue a stopped Burn-In test. See nstructon. below for nformaton how to do ths. Resume Burn-In Mode To resume a stopped Burn-In mode at a later date:. Pont the remote control at a controller. Press n/ff/shft key and scene 0/ Note: If a Power ff/n cycle occurs, the counter wll be reset to 0. Mode Identfcaton To establsh whch Dm Sense mode s selected:. Pont the remote control at a controller. Press n/ff/shft key and scene Start/Stop PIR Walk Test. Pont the remote control at a controller.8 Press n/ff/shft key and scene 0/ Note: Number of flashes depends on mode selected. See overleaf for detaled LED nformaton 0/ sec sec Helvar 0 Remote Control DIM: Installaton and User Gude Doc. D00 ssue,

4 LED Flash Feedback Two LEDs, red and green, located n the Dm Sense flash to provde vsual feedback for varous states. Functon User Defned Mode Selected Followng an upload from IR Remote Mode Selected (Classroom) LED Flash Feedback Mode Selected (Sngle ffce) Mode Selected (pen Plan ffce) Mode Selected (Corrdor Lnk) Mode Selected (Corrdor Hold) Mode Selected (Meetng Room) PIR Walk Test Mode Sequence repeats untl walk test s complete 00 hour Burn-In Mode Sequence repeats untl burn-n s complete sec sec sec DALI Errors Sequence repeats untl error clears Change from unoccuped to occuped Typcally follows a PIR detecton Data receved from IR Remote Re-enablng of IR Remote. Successful upload from IR Remote. Vsble after storng modfed settngs Faled upload from IR Remote. Vsble when modfed settngs upload fals. Excluded from use wth DIGIDIM 0 Remote Control Helvar 0 Remote Control DIM: Installaton and User Gude Doc. D00 ssue,

5 Techncal Data Connectons Power Power supply: Range peratng range: No external physcal connectons are necessary IEC, LR0/AAA. V Battery Approxmately m: wth ±. angle to panels wth ± angle to multsensors peraton IR frequency: khz Mechancal data Dmensons: mm 8 mm 9 mm Housng: Matt dark grey, nonflammable polycarbonate, halogen free Weght: 0 g peratng condtons Ambent temperature: 0 C to 0 C Relatve humdty: Max. 90 %, non-condensng Storage temperature: 0 C to 0 C Conformty and standards Envronment: Comples wth WEEE and RoHS drectves Helvar 0 Remote Control DIM: Installaton and User Gude Doc. D00 ssue,