Interconnecting Cisco Networking Devices Part2 (ICND2) Exam.

Size: px

Start display at page:

Download "Interconnecting Cisco Networking Devices Part2 (ICND2) Exam."

Oswin Parrish
5 years ago
Views:

1 Cisco Interconnecting Cisco Networking Devices Part2 (ICND2) Exam TYPE: DEMO Examskey Cisco exam demo product is here for you to test quality of the product. This Cisco demo also ensures that we have this product ready unlike most companies, which arrange the product for you as you order these exam questions are prepared by Cisco subject matter specialists. Hence these are most accurate version of the exam questions that you can get in the market. We also offer bundle discount packages for every Cisco certification track, so you can buy all related exam questions in one convenient bundle. And for corporate clients we also offer bundles for Cisco certification exams at huge discount. Check out our Exam Page and Cisco Certification Page for more details of these bundle packages. 1

Question: 1 To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.) A.

2 Question: 1 To allow or prevent load balancing to network /24, which of the following commands could be used in R2? (Choose two.) A. R2(config-if)#clock rate B. R2(config-if)#bandwidth C. R2(config-if)#ip ospf cost D. R2(config-if)#ip ospf priority E. R2(config-router)#distance ospf Answer: B, C Question: 2 2

3 After the network has converged, what type of messaging, if any, occurs between R3 and R4? A. No messages are exchanged B. Hellos are sent every 10 seconds. C. The full database from each router is sent every 30 seconds. D. The routing table from each router is sent every 60 seconds. Answer: B Question: 3 OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF? A. 2 3

4 B. 3 C. 4 D. 5 E. 6 F. 7 Answer: C Question: 4 R1 is configured with the default configuration of OSPF. From the following list of IP addresses configured on R1, which address will the OSPF process select as the router ID? A B C D Answer: A Question: 5 DRAG DROP Riverside Towing is redesigning the network that connects its three locations. The administrator gave the networking team to use for addressing the entire network. After subnetting the address, the team is ready to assign the addresses. The administrator plans to configure ip subnet-zero and use RIP v2 as the routing protocol. As a member of the networking team, you must 4

address the network and at the same time conserve unused addresses for future growth. With those goals in mind, drag the host addresses on the left to the correct router interface.

5 address the network and at the same time conserve unused addresses for future growth. With those goals in mind, drag the host addresses on the left to the correct router interface. One of the routers is partially configured. Move your mouse over a router to view its configuration. Not all of the host addresses on the left are necessary. Answer: Cars Fa0/0 IP = /26 Trucks S0/1 IP = /30 Trucks Fa0/0 IP = /28 Vans Fa0/0 IP = /25 Question: 6 Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.) A. Global addresses start with 2000::/3. B. Link-local addresses start with FE00::/12. C. Link-local addresses start with FF00::/10. D. There is only one loopback address and it is :: 1. E. If a global address is assigned to an interface, then that is the only allowable address for the interface. Answer: A, D Question: 7 5

Refer to the exhibit. Given the partial configuration shown in the exhibit, why do internal workstations on the 192.168.1.0 network fail to access the Internet? A. A NAT pool has not been defined. B.

6 Refer to the exhibit. Given the partial configuration shown in the exhibit, why do internal workstations on the network fail to access the Internet? A. A NAT pool has not been defined. B. The wrong interface is overloaded. C. NAT has not been applied to the inside and outside interfaces. D. The access list has not been applied to the proper interface to allow traffic out of the internal network. Answer: C Question: 8 6

7 Refer to the exhibit. Hosts in network are unable to reach hosts in network Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.) A. Interface S0/0 on RouterB is administratively down. B. Interface S0/0 on RouterA is configured with an incorrect subnet mask. C. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU. D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet. E. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA. F. The cable that is connected to S0/0 on RouterA is faulty. Answer: C,E Explanation: Based on the information provided in the exhibit, we know that Serial0/0 is up, line protocol is down, under normal circumstances there are three states: 1. serial0/0 up, line protocol is up The interface is up and the line protocol is up 2. serial0/0 down, line protocol is down The interface is down and there is something wrong with the physical layer. 3. serial0/0 up, line protocol is down The interface is up, but the encapsulation format is not matching,clock rate issues Question: 9 A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration? (Choose three.) A. A switch in the VTP client mode cannot update its local VLAN database. B. A trunk link must be configured between the switches to forward VTP updates. C. A switch in the VTP server mode can update a switch in the VTP transparent mode. D. A switch in the VTP transparent mode will forward updates that it receives to other switches. E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number. F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership. Answer: A, B, D Question: 10 7

Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown C.

8 Refer to the exhibit. What statement is true of the configuration for this network? A. The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported. B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown C. The number 1 referred to in the ip nat inside source command references access-list number 1. D. ExternalRouter must be configured with static routes to networks /24 and /24. Answer: C Question: 11 Refer to the exhibit. Which mask is correct to use for the WAN link between the routers that will provide connectivity while wasting the least amount of addresses? 8

A. /23 B. /24 C. /25 D. /30 Answer: D Question: 12 Refer to the exhibit. What can be determined about the interfaces of the Main_Campus router from the output shown? A. The LAN interfaces are configured on different subnets.

9 A. /23 B. /24 C. /25 D. /30 Answer: D Question: 12 Refer to the exhibit. What can be determined about the interfaces of the Main_Campus router from the output shown? A. The LAN interfaces are configured on different subnets. B. Interface FastEthernet 0/0 is configured as a trunk. C. The Layer 2 protocol of interface Serial 0/1 is NOT operational. D. The router is a modular router with five FastEthernet interfaces. E. Interface FastEthernet 0/0 is administratively deactivated. Answer: B Question: 13 What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.) 9

A. They create split-horizon issues. B. They require a unique subnet within a routing domain. C. They emulate leased lines. D. They are ideal for full-mesh topologies. E.

10 A. They create split-horizon issues. B. They require a unique subnet within a routing domain. C. They emulate leased lines. D. They are ideal for full-mesh topologies. E. They require the use of NBMA options when using OSPF. Answer: B, C Question: 14 Refer to the exhibit. Which switch provides the spanning-tree designated port role for the network segment that services the printers? A. Switch1 B. Switch2 C. Switch3 D. Switch4 Answer: C Explanation: Printers are connected by hubs. Decide the switch that provides the spanning-tree designated port role between Switch3 and Switch4. They have the same priority Compare their MAC addresses. Switch3 with a smaller MAC address will provide a designated port for printers. 10

Designated port A designated port is one that has been determined as having the best (lowest) cost. A designated port will be marked as a forwarding port.

11 Designated port A designated port is one that has been determined as having the best (lowest) cost. A designated port will be marked as a forwarding port. Question: 15 SIMULATION A new switch is being added to the River Campus LAN. You will work to complete this process by first configuring the building_210 switch with an IP address and default gateway. For the switch host address, you should use the last available IP address on the management subnet. In addition, the switch needs to be configured to be in the same VTP domain as the building_100 switch and also needs to be configured as a VTP client. Assume that the IP configuration and VTP configuration on building_100 are complete and correct. The configuration of the router is not accessible for this exercise. You must accomplish the following tasks: Determine and configure the IP host address of the new switch. Determine and configure the default gateway of the new switch. Determine and configure the correct VTP domain name for the new switch. Configure the new switch as a VTP client. Answer: PENDING Question: 16 DRAG DROP Drag each feature of the left to the appropriate routing protocol on the right. 11

12 Answer: 12

13 RIP Version 1 Sends frequent updates Less complex configuration Susceptible to routing loops Exchanges full routing table in updates OSPF Faster convergence Uses only event-triggered updates Same topology information held by all routers Requires more memory and processing power Question: 17 What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when configuring a Frame Relay hub in a hub-and-spoke topology? A. It avoids split-horizon issues with distance vector routing protocols. B. IP addresses can be conserved if VLSM is not being used for subnetting. C. A multipoint interface offers greater security compared to point-to-point subinterface configurations. D. The multiple IP network addresses required for a multipoint interface provide greater addressing flexibility over point-to-point configurations. Answer: B Explanation: Frame Relay supports two types of interfaces: point-to-point and multipoint. The one you choose determines whether you need to use the configuration commands that ensure IP address to datalink connection identifier (DLCI) mappings. After configuring the PVC itself, you must tell the router which PVC to use in order to reach a specific destination. Let s look at these options: 1. Point-to-point subinterface With point-to-point subinterfaces, each pair of routers has its own subnet. If you put the PVC on a point-to-point subinterface, the router assumes that there is only one point-to-point PVC configured on the subinterface. Therefore, any IP packets with a destination IP address in the same subnet are forwarded on this VC. This is the simplest way to configure the mapping and is therefore the recommended method. Use the frame-relay interface-dlci command to assign a DLCI to a specified Frame Relay subinterface. 2. Multipoint networks Multipoint networks have three or more routers in the same subnet. If you put the PVC in a point-to-multipoint subinterface or in the main interface (which is multipoint by default), you need to either configure a static mapping or enable inverse Address Resolution Protocol (ARP) for dynamic mapping. Question: 18 13

14 Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router? A B C D Answer: C 14

15 Thank You for Trying Our Product Cisco Interconnecting Cisco Networking Devices Part2 (ICND2) Exam TYPE: DEMO View list of All certification exams: Average 100% Success Rate. 100% Money Back Guarantee Study Material Updated On Regular Basis. Instant Download Access! After Purchased Services Of Professional & Certified Experts Available Via Support Round-The-Clock Client Support, Safe Website For Shopping Besides money back guarantee, our also offer 3 months free updates to the exam questions to reflect the changes as (& if) they are introduced by the Cisco. 15

Cisco Interconnecting Cisco Networking Devices Part 2.

http://www.officialcerts.com 640-816 Cisco Interconnecting Cisco Networking Devices Part 2 OfficialCerts.com is a reputable IT certification examination guide, study guides and audio exam provider. We