Q&As. Interconnecting Cisco Networking Devices Part 1. Pass Cisco Exam with 100% Guarantee

Size: px

Start display at page:

Download "Q&As. Interconnecting Cisco Networking Devices Part 1. Pass Cisco Exam with 100% Guarantee"

Emory Bradley
5 years ago
Views:

640-822 Q&As Interconnecting Cisco Networking Devices Part 1 Pass Cisco 640-822 Exam with 100% Guarantee Free Download Real Questions & Answers PDF and VCE file from: 100% Passing

1 Q&As Interconnecting Cisco Networking Devices Part 1 Pass Cisco Exam with 100% Guarantee Free Download Real Questions & Answers PDF and VCE file from: 100% Passing Guarantee 100% Money Back Assurance Following Questions and Answers are all new published by Cisco Official Exam Center PDF Dumps Practice Test Braindumps 1 / 17

2 QUESTION 1 On a Cisco router which two router modes can be protected by a password? (Choose two.) A. user mode B. privileged mode C. global configuration mode D. router configuration mode E. interface configuration mode Correct Answer: AB QUESTION 2 At the global configuration prompt, the administrator has just entered the following command on a router that has not been previously configured for RIP: RouterA(config)# router rip What state is the router now in after executing the command? A. The RIP process has started, but no updates are being sent. B. The RIP process has started, and by default all updates are being sent RIPv1. C. The RIP process has started, and by default all updates are being sent RIPv2. D. The router has entered router configuration mode but the RIP process has not started. Correct Answer: D QUESTION 3 Refer to the exhibit PDF Dumps Practice Test Braindumps 2 / 17

The wire scheme that is shown is terminated at each end with an RJ-45 connector. What cable type does the wire diagram represent? A. an Ethernet straight-through cable B.

3 The wire scheme that is shown is terminated at each end with an RJ-45 connector. What cable type does the wire diagram represent? A. an Ethernet straight-through cable B. a serial crossover cable C. a serial straight-through cable D. an Ethernet crossover cable E. a rollover cable Correct Answer: D PDF Dumps Practice Test Braindumps 3 / 17

QUESTION 4 If the hubs in the graphic were replaced by switches, what would be virtually eliminated? A. broadcast domains B. repeater domains C. Ethernet collisions D. signal amplification E.

4 QUESTION 4 If the hubs in the graphic were replaced by switches, what would be virtually eliminated? A. broadcast domains B. repeater domains C. Ethernet collisions D. signal amplification E. Ethernet broadcasts Correct Answer: C QUESTION 5 An administrator is in the process of changing the configuration of a router. What command will allow the administrator to check the changes that have been made prior to saving the new configuration? A. Router# show startup-config B. Router# show current-config C. Router# show running-config D. Router# show memory E. Router# show flash F. Router# show processes PDF Dumps Practice Test Braindumps 4 / 17

Correct Answer: C QUESTION 6 Refer to the exhibit. What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A? A. VLAN 1 on RT-A B.

5 Correct Answer: C QUESTION 6 Refer to the exhibit. What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A? A. VLAN 1 on RT-A B. IP routing on SW-A C. default gateway on SW-A D. crossover cable connecting SW-A and RT-A Correct Answer: C QUESTION 7 What starting binary pattern indicates an address range evenly split between network and host size? A. 01xxxxxx B. 0xxxxxxx C. 10xxxxxx D. 110xxxxx Correct Answer: C QUESTION 8 A PC is attached to the console port of a new Cisco router. The router is powered on. If the PC has been configured correctly for a console connection, what will the router display after it powers up? A. Router> PDF Dumps Practice Test Braindumps 5 / 17

6 B. an option to execute the show running-config command C. a series of prompts to run various POST tests D. the option to enter initial system configuration information Correct Answer: D QUESTION 9 Refer to the exhibit. What is the result of the entries shown? A. A copy of the router-config file stored on the TFTP server with an IP address of will be downloaded to the local router where it is stored under the name of startup-config. B. A copy of the file startup-config stored on the TFTP server with an IP address of will be downloaded to the local router where it is stored under the name of router- config. C. A copy of local startup-config file will be uploaded to the TFTP server with an IP address of where it is stored under the name of router-config. D. A copy of local router-config file will be uploaded to the TFTP server with an IP address of where it is stored under the name of startup-config. Correct Answer: C QUESTION 10 Which two characteristics apply to Layer 2 switches? (Choose two.) A. increases the number of collision domains B. decreases the number of collision domains C. implements VLAN D. decreases the number of broadcast domains E. uses the IP address to make decisions for forwarding data packets Correct Answer: AC PDF Dumps Practice Test Braindumps 6 / 17

QUESTION 11 Refer to the exhibit. The network administrator is testing connectivity from the branch router to the newly installed application server.

7 QUESTION 11 Refer to the exhibit. The network administrator is testing connectivity from the branch router to the newly installed application server. What is the most likely reason for the first ping having a success rate of only 60 percent? A. The network is likely to be congested, with the result that packets are being intermittently dropped. B. The branch router had to resolve the application server MAC address. C. There is a short delay while NAT translates the server IP address. D. A routing table lookup delayed forwarding on the first two ping packets. E. The branch router LAN interface should be upgraded to FastEthernet. Correct Answer: B QUESTION 12 What TCP message does a host send to establish a connection with a destination host? A. Establish B. Request open C. SYN D. ISN E. ACK F. HELLO Correct Answer: C QUESTION 13 Which Layer 1 devices can be used to enlarge the area covered by a single LAN segment? (Choose two.) A. switch B. router PDF Dumps Practice Test Braindumps 7 / 17

8 C. NIC D. hub E. repeater F. RJ-45 transceiver Correct Answer: DE QUESTION 14 What is the purpose of a default route? A. It is a route to be used when the routing protocol fails. B. It is a route configured by an ISP that sends traffic into a corporate network. C. It is a route used when a packet is destined for a remote network that is not listed in the routing table. D. It is a route manually configured for a specific remote network for which a routing protocol is not configured. E. It is used to send traffic to a stub network. Correct Answer: C QUESTION 15 You need to configure 52 hosts for a computer lab. Which subnet mask is appropriate? A B C D Correct Answer: D QUESTION 16 Which of the following describe private IP addresses? (Choose two.) A. addresses chosen by a company to communicate with the Internet B. addresses that cannot be routed through the public Internet C. addresses that can be routed through the public Internet D. a scheme to conserve public addresses PDF Dumps Practice Test Braindumps 8 / 17

9 E. addresses licensed to enterprises or ISPs by an Internet registry organization Correct Answer: BD QUESTION 17 Refer to the topology below. What interfaces on Router1 have not had any configurations applied? (Choose two) A. Ethernet 0 B. FastEthenet 0/0 C. FastEthernet 0/1 D. Serial 0 E. Serial 0/0 F. Serial 0/1 Correct Answer: CF QUESTION 18 The network administrator is configuring a Cisco router. The prompt on the screen is: Router(config-if)# PDF Dumps Practice Test Braindumps 9 / 17

What is true of this prompt? (Choose three.) A. An interface password can be set at this prompt. B. Settings that affect all router interfaces can be globally configured at this prompt. C.

10 What is true of this prompt? (Choose three.) A. An interface password can be set at this prompt. B. Settings that affect all router interfaces can be globally configured at this prompt. C. An interface can be activated or deactivated from this prompt. D. The administrator will arrive at this prompt by typing interface fa0/0 from the global configuration mode. E. The administrator will arrive at this prompt by typing configure terminal from the EXEC prompt. F. An interface IP address can be configured at this prompt. Correct Answer: CDF QUESTION 19 Refer to the exhibit. Which two statements are correct? (Choose two.) A. This is a default route. B. Adding the subnet mask is optional for the ip route command. C. This will allow any host on the network to reach all known destinations beyond RouterA. D. This command is incorrect, it needs to specify the interface, such as s0/0/0 rather than an IP address. E. The same command needs to be entered on RouterA so that hosts on the network can reach network Correct Answer: AC QUESTION PDF Dumps Practice Test Braindumps 10 / 17

Refer to the exhibit. The network administrator is configuring RTA to connect to a non-cisco network. Which two commands would be applied to the S0/0 WAN interface, but not to the Fa0/0 LAN interface?

11 Refer to the exhibit. The network administrator is configuring RTA to connect to a non-cisco network. Which two commands would be applied to the S0/0 WAN interface, but not to the Fa0/0 LAN interface? (Choose two.) A. speed B. no shutdown C. ip address D. authentication pap E. encapsulation ppp Correct Answer: DE QUESTION 21 A switch has 48 ports and 4 VLANs. How many collision and broadcast domains exist on the switch (collision, broadcast)? A. 4, 48 B. 48, 4 C. 48, 1 D. 1, 48 E. 4, 1 Correct Answer: B PDF Dumps Practice Test Braindumps 11 / 17

12 QUESTION 22 Refer to the exhibit. Which types of devices and connections are needed to complete the LAN for optimal performance and cost efficiency? A. A) router B) hub C) switch D) UTP cable E) fiber connection F) fiber connection B. A) switch B) switch C) switch D) UTP cable E) fiber connection F) T-1 connection C. A) router B) switch C) router D) fiber connection E) Cat5 cable F) T-1 connection D. A) router B) switch C) switch D) UTP cable E) fiber connection F) T-1 connection E. A) router B) hub C) switch D) fiber cable E) cat5 cable F) T-1 connection Correct Answer: D QUESTION 23 What is the last usable address of the network ? A B C D Correct Answer: B PDF Dumps Practice Test Braindumps 12 / 17

13 QUESTION 24 Refer to the exhibit. What kind of cable should be used to make each connection that is identified by the numbers shown? A. 1 - Ethernet crossover cable 2 - Ethernet straight-through cable 3 - fiber optic cable 4 - rollover cable B. 1 - Ethernet straight-through cable 2 - Ethernet straight-through cable 3 - serial cable 4 - rollover cable C. 1 - Ethernet rollover cable 2 - Ethernet crossover cable 3 - serial cable 4 - null modem cable D. 1 - Ethernet straight-through cable 2 - Ethernet crossover cable 3 - serial cable 4 - rollover cable E. 1 - Ethernet straight-through cable 2 - Ethernet crossover cable 3 - serial cable 4 - Ethernet straight-through cable Correct Answer: B QUESTION 25 You run the command debug ip rip on your router and notice this entry: 08:08:30: RIP: build update entries 08:08:30: network metric 16 What is this information telling you? A. It provides the administrative distance for this route PDF Dumps Practice Test Braindumps 13 / 17

B. The route has exceeded its maximum hop count. C. There are 16 hops to reach this route. D. It establishes the route update timer parameter E. The route will be flushed in 16 seconds.

14 B. The route has exceeded its maximum hop count. C. There are 16 hops to reach this route. D. It establishes the route update timer parameter E. The route will be flushed in 16 seconds. Correct Answer: B QUESTION 26 Refer to the exhibit. A network technician is attempting to use HyperTerminal to configure a new router using the settings shown. What is the reason the technician is unable to connect to the router? A. The bits per second should be set to B. The data bits should be set to 6. C. Parity should be set to mark. D. The stop bits should be set to 2. E. Flow control should be set to hardware. Correct Answer: A QUESTION 27 The network manager states, "The only UDP port allowed on this router interface is 53." From the statement, what can be concluded about traffic on the router interface? A. DNS traffic is allowed PDF Dumps Practice Test Braindumps 14 / 17

15 B. RIP traffic is allowed. C. SMTP traffic is allowed. D. Telnet traffic is allowed. Correct Answer: A QUESTION 28 Which command will set the default gateway to on a Cisco switch? A. Switch(config)# ip default-network B. Switch(config)# ip route-default C. Switch(config)# ip default-gateway D. Switch(config)# ip route Correct Answer: C QUESTION 29 After the shutdown command has been issued on the serial 0/0 interface, what will be displayed when the show interface serial 0/0 command is issued by the administrator? A. Serial0/0 is administratively down, line protocol is down B. Serial0/0 is down, line protocol is down C. Serial0/0 is up, line protocol is down D. Serial0/0 is administratively down, line protocol is administratively down E. Serial0/0 is up, line protocol is up F. Serial0/0 is down, line protocol is up Correct Answer: A QUESTION 30 Refer to the exhibit PDF Dumps Practice Test Braindumps 15 / 17

The enterprise has decided to use the network address 172.16.0.

16 The enterprise has decided to use the network address The network administrator needs to design a classful addressing scheme to accommodate the three subnets, with 30, 40, and 50 hosts, as shown. What subnet mask would accommodate this network? A B C D E Correct Answer: A PDF Dumps Practice Test Braindumps PDF Dumps Practice Test Braindumps 16 / 17

Powered by TCPDF (www.tcpdf.org) To Read the Whole Q&As, please purchase the Complete Version from Our website. Try our product!

17 Powered by TCPDF ( To Read the Whole Q&As, please purchase the Complete Version from Our website. Try our product! 100% Guaranteed Success 100% Money Back Guarantee 365 Days Free Update Instant Download After Purchase 24x7 Customer Support Average 99.9% Success Rate More than 800,000 Satisfied Customers Worldwide Multi-Platform capabilities - Windows, Mac, Android, iphone, ipod, ipad, Kindle We provide exam PDF and VCE of Cisco, Microsoft, IBM, CompTIA, Oracle and other IT Certifications. You can view Vendor list of All Certification Exams offered: Need Help Please provide as much detail as possible so we can best assist you. To update a previously submitted ticket: Any charges made through this site will appear as Global Simulators Limited. All trademarks are the property of their respective owners. Copyright pass4lead, All Rights Reserved PDF Dumps Practice Test Braindumps 17 / 17

Vendor: Cisco. Exam Code: Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) Version: Demo

Vendor: Cisco. Exam Code: Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) Version: Demo Vendor: Cisco Exam Code: 100-105 Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) Version: Demo DEMO QUESTION 1 If the resume command is entered after the sequence that is