TIM J 5/16 USER MANUAL

Size: px

Start display at page:

Download "TIM J 5/16 USER MANUAL"

Willis Evans
6 years ago
Views:

1 TIM J 5/16 USER MANUAL

2 10.b 10.a 11.a 11.b 10.f 11.c 10.g 11.d 12.a/b 10.c 10.d 10.h/i 9 1.a c 1.b a/b 7 11.e

3 FULL PART LIST: 1. Drum Head: a. 10 tom-tom head x 2 pcs b. 12 floor tom head x 2 pcs c. 16 bass drum head x 2 pcs 2. Assembled snare drum x 1 pcs 3. Assembled 8 tom-tom x 1 pcs tom-tom shell x 1 pc + hoop x 2 pcs + 2 locked lugs floor tom shell x 1 + pc + hoop x 2 pcs bass drum shell x 1 pc + hoop x 2 pcs 7. Seat of drum throne 8. 8 hi-hat x 1 pair cymbal x 1 pc 10. Spare Part carton: a. Cymbal stand x 1 pc b. Central tom holder x 1 pc c. Floor tom feet x 3 pcs d. Bass drum feet x 2 pcs e. Drum sticks x 1 pair f. 3 (7.5cm) lug for 10 tom-tom x 6 pcs g. 4.3 (11cm) lug for 12 floor tom x 8 pcs h. 6 (15cm) lug for 16 bass drum x 8 pcs i. Bass drum lug hook x 8 pcs j. Lug spacers x 22 pcs k. Drum key x 1 pc 11. Hi-hat Stand carton: a. Pull rod x 1 pc b. Clutch x 1 pc c. Top section tube x 1 pc d. Feet section x 1 pc e. Feet section of drum throne 12. Snare Stand carton: a. Basket arm x 1 pc b. Feet stand x 1 pc 13. Drum Pedal carton: a. Drum pedal x 1 pc b. Beater x 1 pc

4 a. HI-HAT Top hi-hat x 1 1 Bottom hi-hat x 1 2 Insert the foot pedal rod and tighten. Feet section Top section 3 Open the feet and make sure all feet are well secured to the ground. 4 Tighten the feet & foot pedal rod. 5 Take out the pull rod from the top-section tube and leave the clutch aside. 6 Insert the pull rod and tighten. Pull rod Top-section tube Clutch Insert the top-section tube and tighten. 7 8 Place the bottom hi-hat.

5 Disassemble the clutch. Place the top hi-hat on the clutch rod Assemble the felt and the screw back. Fit the top hi-hat on the pull rod and tighten the screw. 12 You may leave some space for playing open and close sound Adjustable tilter for adjusting the angle of bottom hi-hat b. Throne Pull open the legs and tighten. 1 2 Seat Feet Adjustable tube Set the throne to appropriate height and tighten. 3 4 Fit seat to the stand and tighten.

6 c. Snare drum Pull open the legs and tighten. 1 Assembled snare drum 2 Basket arm Stand-feet 3 Insert the basket arm to appropriate height and tighten open the arms 1. adjust the arm to horizontal position and tighten 3.loose the screw and pull the arm Place the snare drum on basket. 5 6 You may adjust the snare by tuning the knob.

d. Floor tom & 10 tom-tom 12 Head x2 pcs drum key x1

Floor tom Leg x 3 pcs Hoop x2 pcs Tension rod & spacer

The holes on the hoop should be straight to the lug 4

NOTE: DO NOT FULLY TIGHTEN Rod Spacer Hoop Lug 5

1st 4th 3rd 2nd Note: Do not fully tighten one rod at

Please tune rods in the diametrical order as above.

7 d. Floor tom & 10 tom-tom 12 Head x2 pcs drum key x1 pc 1 2 Place a head on the floor tom. Floor tom Leg x 3 pcs Hoop x2 pcs Tension rod & spacer x 8 pcs 3 Place the hoop onto the head. The holes on the hoop should be straight to the lug 4 Screw the tension rod to the lug. NOTE: DO NOT FULLY TIGHTEN Rod Spacer Hoop Lug 5 Repeat the same procedure on the other side until all lugs are half screwed. 6 Use the drum key to tune the tension rod. 1st 4th 3rd 2nd Note: Do not fully tighten one rod at a time. Please tune rods in the diametrical order as above. Repeat several times until the tension of each rod is equal. The higher tension you tune, the higher pitch it would sound Insert the floor tom legs into the leg bracket to appropriate height and tighten. 7 8

e. Bass drum Hoop x2 pcs Bass drum x1 1 2

spacer + bracket Drum key 3 Bass drum head

NOTE: DO NOT FULLY TIGHTEN 5 Repeat the same

1st 4th 3rd 2nd Note: Do not fully tighten one

Please tune rods in the diametrical order as

8 e. Bass drum Hoop x2 pcs Bass drum x1 1 2 Prepare 8 sets of bass drum tension rod + spacer + bracket Drum key 3 Bass drum head x2pcs tension rod set x8 sets 1. Place the head with logo on the front side of the bass drum. 2. Place the hoop onto the drum head. 4 Screw the tension rod to the lug. NOTE: DO NOT FULLY TIGHTEN 5 Repeat the same procedure on the other side until all rods are half screwed. 6 Use the drum key to tune the tension rod. 1st 4th 3rd 2nd Note: Do not fully tighten one rod at a time. Please tune rods in the diametrical order as above. Repeat several times until the tension of each rod is equal. The higher tension you tune, the higher pitch it would sound Insert the legs to the leg bracket and tighten. 7 8 Bass drum leg x 2 pcs

9 f. Tom-tom, cymbal arm & bass drum pedal Insert the tom tom holder to the holder bracket and tighten. 1 2 Hang 8 and 10 tom tom on the holder The logo should face the audience. 3 Insert the cymbal arm to the holder bracket and tighten. 4 Unscrew the cymbal lock and leave single felt on the holder. 1. Place the cymbal between 2 felts. 2. Place the spacer on the top. 3. Lock the cymbal. 5 6 Don t forget to connect your bass drum pedal before playing.

10 Notes:

11 Notes:

Drum Set Owner s Manual D2518

Drum Set Owner s Manual D2518 5-PIECE SoundPercussionLabs.com Thank you for purchasing this Sound Percussion Labs drum set. Please take a few moments to familiarize yourself with this set-up guide so you can assemble your new drums