DTA-SDH/155 Operating Manual

Transcription

1 Copyright 2014, Shineway Technologies, Inc. All rights reserved

2 1. Instrument Profile Physical Characteristics Introduction to Graphical User Interface Test Configuration Test Mode SDH Path Mode (Default Mode of the Manufacturer) SDH Demux Mode SDH Mux Mode SDH Monitor Mode SDH Through Mode PDH Path Mode PDH Monitor Mode PDH Span Mode PDH Through Mode Parameter Setup Physical Interface Receiving Gain Mapping PRBS Code Pattern Transmission Clock LED Interface SDH Interface TCM Interface Error Performance Analyzer Tests Summary Error Test Result Error Performance Analyser SDH Part PDH Part Event Record Trace Overhead Test Regular Overhead Test Pointer Value Test Pointer Sequences Test Error Insert Test Insert Alarm Pointer Adjusting Test Function Test APS Test Data Path (Transparency) Test TCM Test RTD Test Tributary Scan Test Test Result Alarm Test Result Error Code Test Result Pointer Test Result Overhead Test Result TCM Test Result Data Path Test (Transparency) Result Frequency Test Result Tributary Test Result System Setup File Management Configuration File: Result File Shineway Technologies, Inc. 2

3 7.2. Version Information Recover Default Time Setup Touch Screen Calibration Other Setup Performance Objectives USB Connection Shineway Technologies, Inc. 3

4 1. Instrument Profile 1.1. Physical Characteristics This chapter introduces various major parts of DTA-SDH/155 so that you can know the appearance and overall structure of the instrument. Façade Top Figure 1-1 DTA-SDH/155 Profile Shineway Technologies, Inc. 4

5 (1) Electrical adapter port; (2) BNC input joint for external clock; (3) Standard USB port; (4) BNC joint of output port; (5) BNC joint of input port; (6) SFP port for opticalinput/output. Figure 1-2 Top View Shineway Technologies, Inc. 5

6 Figure 1-3 Façade View (1) Fastening metal buckle of the belt; (2) Color LCD screen; (3)LED pointer light; :Instrumentation Power on instructions; :Instrumentation external power supply instructions; Note: In order to ensure the performance and battery life, please use the first three put the battery completely discharge and recharge hours, After 4-6 hours per charge achieved. (4) Keypad: keys can be used for operation in case of the failure of touch screen. Shineway Technologies, Inc. 6

7 Figure 1-4 Back View (1) Back bracket of the instrument; (2) Battery cabin Introduction to Graphical User Interface This chapter introduces the graphical user interface (GUI) of DTA-SDH/155. ⑴ ⑵ ⑶ [4] Figure 1-5 Graphical User Interface (1) Information prompt area: including the error, alarm, insert error, running prompt and electric Shineway Technologies, Inc. 7

8 quantity of battery; (2) Main display area: the display of various functions, setup and test results of the instrument; (3) Function key area: different function keys in different interfaces to realize the operation of the instrument; (4)Language select. 2. Test Configuration The test configuration interface defines the setup of different test modes, which is the most basic setup for specific test of instrument, mainly including test mode select, port select, mapping and test code pattern select. See Figure 2-1 as follows: Figure 2-1 Test Configuration Interface Six shortcut keys in the lower part of the interface are defined as follows: Set all parameter setups in the interface are valid; Save save up the current setup. As in Figure 2-2 Save Interface, a file name can be selcted for saving up the current configuration. Shineway Technologies, Inc. 8 Figure 2-2 Save Interface

9 Load load a stored configuration file as in Figure 2-3 Configuration File: Figure 2-3 Configuration File Click Load to pop up a stored configuration file, select a file name and confirm. In this case, configuration parameters are the contents of a selected configuration file. Press Set to make the configuration valid. Insert insert error code, overhead and alarm for a test. Start press the current configuration to implement a test. When the test starts, the run key on the upper part of the interface becomes green, and Start key changes to Stop key. Click the stop button to suspend the current test. At the same time, the pointer light Start on the upper part of the interface returns to grey; Exit exit the current interface (test status unchanged), and return to the previous interface Test Mode As in Figure 2-4, the instrument has nine test modes. Figure 2-4 Test Mode Interface Shineway Technologies, Inc. 9

10 SDH Path Mode (Default Mode of the Manufacturer) For the structure chart, see Figure 2-5 as follows: SDH Demux Mode Figure 2-5 SDH Path Mode For the structure chart, see Figure 2-6 as follows: SDH Mux Mode Figure 2-6 SDH Path Demux Mode For the structure chart, see Figure 2-7 as follows: Figure 2-7 SDH Mux Mode Shineway Technologies, Inc. 10

11 SDH Monitor Mode For the structure chart, see Figure 2-8 as follows: SDH Through Mode Figure 2-8 SDH Monitor Mode For the structure chart, see Figure 2-9 as follows: PDH Path Mode Figure 2-9 SDH Through Mode For the structure chart, see Figure 2-10 as follows: PDH Monitor Mode Figure 2-10 PDH Path Mode For the structure chart, see Figure 2-11 as follows: Shineway Technologies, Inc. 11

12 Figure 2-11 PDH Monitor Mode PDH Span Mode For the structure chart, see Figure 2-12 as follows: PDH Through Mode Figure 2-12 PDH Span Mode For the structure chart, see Figure 2-13 as follows: 2.2. Parameter Setup Figure 2-13 PDH Through Mode Physical Interface The instrument supports electrical port and optical port. In SDH test mode, physical interface can be selected as optical port- O or electrical port- E while consistent ports are required for receiving or transmission i.e. both O or both E. In PDH test, only electrical port- E is available. For the physical interface setup, see Figure 2-14 as follows: Shineway Technologies, Inc. 12

13 Figure 2-14 Physical Interface Setup Receiving Gain The instrument supports receiving gain at two levels including 0dB and 18dB. See Figure 2-15 as follows: Figure 2-15 Receiving Gain Setup Mapping The mapping and de-mapping modes: E1 (unframed, CCS, CCS/CRC, CAS & CAS/CRC), E3 (unframed/frame), E4 (unframed/frame), C-12 (KLM optional), C-3 (TUG3 optional), C-4. Receiving and transmission can be set up separately- RX TX. Moreover, a coupling mode can be set up- RX=TX. See Figure 2-16 as follows: Shineway Technologies, Inc. 13

14 Figure 2-16 Mapping Mode Setup PRBS Code Pattern For the setup interface of test code pattern, see Figure 2-17 as follows: Figure 2-17 Test Code Pattern Setup Options for test code pattern: 2E23, 2E23 (INV), 2E20, 2E20 (INV), 2E15, 2E15 (INV), 2E11, 2E11 (INV), 2E9, 2E9 (INV), 1111 and The receiving and transmission can be separately set up. Moreover, the coupling mode can also be selected Transmission Clock For the setup interface of transmission clock, see Figure 2-18 as follows: Shineway Technologies, Inc. 14

15 Figure 2-18 Clock Setup 2.3. LED Interface LED interface comprises SDH interface and TCM interface, of which SDH interface includes all alarms and errors of PDH SDH Interface For the interface, see Figure 2-19 as follows: Figure 2-19 LED Indicating Diagram LINE: line-related LOS: loss of signal on line side AIS: alarm indicating signal on line side LOL: loss of locking of line clock Shineway Technologies, Inc. 15

16 LTC: loss of external clock RS: related to regenerator section LOF: loss of frame alignment (6) OOF: frame alignment (5) EFAS: frame alignment (1-4) TIM: trace identifying mark mismatch of regenerator section B1: error code monitoring of regenerator section, and BIP8 check error MS: related to mux section AIS: remote alarm indication of mux section RDI: remote defect indication of mux section REI: remote error indication of mux section B2: error code monitoring of mux section, and BIP-24 check error AU: related to administration unit pointer AIS: status indication signal of AU pointer alarm LOP: loss of AU pointer +PJE: positive AU pointer adjustment -PJE: negative AU pointer adjustment NDF: AU pointer new data symbol INV: invalid AU pointer NEW: new AU pointer PAIS: AU pointer H1, H2 whole 1 alarm indication signal HP: related to high-order path UNQ: high-order path unloaded or monitoring unloaded with signal alarm REI: remote error indication of high-order path RDI: remote defect indication of high-order path PLM: payload mismatch alarm of high-order path TIM: trace identifying mark mismatch of high-order path B3: error code monitoring of high-order path, and high-order B3 check error TU: related to bypass pointer AIS: TU pointer alarm indication signal LOP: loss of TU pointer +PJE: positive TU pointer adjustment -PJE: negative TU pointer adjustment NDF: new data flag of TU pointer INV: invalid TU pointer NEW: new TU pointer PAIS: TU pointer H1, H2 whole 1 alarm indication signal LP: related to low-order path UNQ: low-order path unloaded or monitoring unloaded with signal alarm Shineway Technologies, Inc. 16

17 REI: remote error indication of low-order path RDI: remote defect indication of low-order path PLM: payload mismatch alarm of low-order path TIM: trace identifying mark mismatch of low-order path LOM: loss of multiframe RFI: remote failure indication of low-order path BIP-2: monitoring of error code of low-order path Frm: related to frame LOF: loss of frame alignment RAI: remote alarm indication CRCL: CRC loss EFAS: frame error ECRC: CRC error REI: error code of remote block MAIS: multiframe alarm indication CASL: multiframe loss MRAI: multiframe remote alarm indication PATTERN: related to code pattern SYNC: PRBS out-of-synchronism AIS: PRBS whole 1 EBIT: PRBS with error code SLIP: PRBS slide code TCM Interface For TCM interface, see Figure 2-20 as follows: HP: high-order path UNEQ: signal not equipped with alarm Figure 2-20 TCM LED Indication Interface Shineway Technologies, Inc. 17

18 LTC: TCM frame loss alarm RDI: TCM remote defect alarm ODI: TCM output defect alarm TIM: TCM trace mismatch REI: TCM remote error alarm OEI: TCM output error alarm AIS: TCM alarm indication signal IEC: TCM input error counting LP: low-order path UNEQ: signal not equipped with alarm LTC: TCM frame loss alarm RDI: TCM remote defect alarm ODI: TCM output defect alarm TIM: TCM trace mismatch REI: TCM remote error alarm OEI: TCM output error alarm AIS: TCM alarm indication signal IEC: TCM input error counting 3. Error Performance Analyzer Error performance analyzer is the second option of the main interface as in Figure 3-1: Figure 3-1 Error Performance Analyzer Interface The error analyzer includes three parts i.e. tests summary, error test result & error performance analyzer. Shineway Technologies, Inc. 18

19 3.1. Tests Summary For tests summary interface, see Figure 3-2 as follows: Figure 3-2 tests summary Start time refers the time of the system when Start shortcut key is clicked on. Duration refers to the continual time keeping after Start time. Click the exit button to stop. Send Pat and Rev Pat are the code sample of PRBS in the Test Configuration interface. Current status is error or alarm indication Error Test Result For error test result interface, see Figure 3-3 as follows: Figure 3-3 Error Test Result Start time refers the time of system when Start shortcut key is clicked on. Duration refers to the continual time keeping after Start time. Click the exit button to stop. Display items include the error code second and ratio of EBIT and EFAS. In any interface, click on Start shortcut key to start synchronous time keeping and operation. Click the exit button to stop. Shineway Technologies, Inc. 19

20 3.3. Error Performance Analyser SDH Part Error performance analyzer of SDH part including: G.826, G.828, G.829 and M G.826 including: MS, HOPOH, LOPOH; and interface indicators including EB, BBE, BBER, ES, ESR, SES, SESR, UAS, UASR. See Figure 3-4 as follows: Figure 3-4 G.826 Analyzer Interface G.828 including: MS, HOPOH, LOPOH; and interface indicators including EB, BBE, BBER, ES, ESR, SES, SESR, UAS, UASR, SEP, SEPR. See Figure 3-5 as follows: Figure 3-5 G.828 Analyzer Interface G.829 including: RS, MS; and interface indicators including EB, BBE, BBER, ES, ESR, SES, SESR, UAS, UASR. See Figure 3-6 as follows: Shineway Technologies, Inc. 20

21 Figure 3-6 G.829 Analyzer Interface M.2101 including: MS, HOPOH, LOPOH; and interface indicators including EB, BE, BER, ES, ESR, SES, SESR, UAS, UASR, SEP, SEPR. See Figure 3-7 as follows: Figure 3-7 M.2101 Analyzer Interface PDH Part Error performance analyser of PDH including: G.821, G.826, M G.821 interface indicators including: EBIT, EBITR, ES, ESR, SES, SESR, UAS, UASR, See Figure 3-8 as follows: Shineway Technologies, Inc. 21

22 Figure 3-8 G.821 Analyzer Interface G.826 interface indicators including EB, BBE, BBER, ES, ESR, SES, SESR, UAS, UASR as in Figure 3-9: Figure 3-9 G.826 Analyzer Interface M.2100 interface indicators including BE, BER, ES, ESR, SES, SESR, UAS and UASR. See Figure 3-10 as follows: Figure 3-10 M.2100 Analyzer Interface Shineway Technologies, Inc. 22

23 In the performance analyzer interface in above, click on the Chart function key to display various results in a chart as in Figure 3-11: Figure 3-11 Result Chart In any interface, click on Start shortcut key to start the synchronous counting and operation. Click on the exit button to stop time keeping and operation. Shineway Technologies, Inc. 23

24 4. Event Record Event record interface including: trace overhead test, regular overhead test, pointer value test, pointer sequence test, error insert test, insert alarm, pointer adjusting test as in Figure Trace Overhead Test Figure 4-1 Event Record Interface Trace overhead test includes HOPOH (J0, J1) & LOPOH (J0, J2). Each part involves Transmit value, Expected value and Receive value. The input value or parameter of Transmit value and Expected value is set up by the Set shortcut key, of which the result influences display select of TCM in LED. Receive value will not be controlled by a shortcut key and receive in real time. The initial interface is HOPOH. See Figure 4-2 as follows: Figure 4-2 Trace Overhead Test J0 has default value of J1 & J2 have default value of Shineway Technologies, Inc. 24

25 4.2. Regular Overhead Test Including HOPOH and LOPOH. See Figure 4-3 as follows: Figure 4-3 Regular Overhead Test The contents include the transmission and receiption of S1, G1, H4, V5, K1, K2, K3, K4 and C2. The Set shortcut key can set up an input value or parameter of Transmit value. Receive value is not controlled by the shortcut key and can receive in real time Pointer Value Test For pointer value test, see Figure 4-4 as follows: Figure 4-4 Pointer Value Test The contents including: Pointer type : AU and TU, with a default value of AU. NDF : ON, OFF, with a default value of OFF, where ON can be inserted only one time. Otherwise, the point may be lost. During a test, OFF can be selected. Setup SS BITS : 10. Transmit value of pointer : scope of setup AU 0-782, TU , TU , with a default value of 128. Shineway Technologies, Inc. 25

26 Receive value of pointer : receive in real time. The Set shortcut key can set up the input value or parameter for Pointer type, NDF, Setup SS BITS and Transmit value of pointer. Receive value of pointer is not controlled by the shortcut key and can receive in real time Pointer Sequences Test For pointer sequences test, see Figure 4-5 as follows: Figure 4-5 Pointer Sequences Test The setup contents of Pointer sequences include: single-step reversed polarity, adding of one pair at fixed period, loss of one at fixed eriod, pair of reversed polarity, single step, burst, 87-3, 87-3 plus, 87-3 minus, periodicity, periodicity plus and periodicity minus, with a default value of single-step reversed polarity. INIT : scope of setup sec, with a minimum step length of 25ms and default value of 60. COOL : scope of setup sec, with a minimum step length of 25ms and default value of 30. T1 : scope of setup sec, with a minimum step length of 25ms, time type of millisecond, sec, minute, hour and default value of 1sec. T2 : scope of setup 0-65sec, with a minimum step length of 1ms, time type of millisecond, sec and default value of 2 millisecond. TADD : scope of setup 0-255, with a default value of1. Pointer type : AU, TU, with a default value of AU. The Set shortcut key can set up all the input values or parameters. Once it is set up, Insert mode changes to the current mode (insert sequence) instead of the original mode with a display on the upper part of the screen. Then, the Insert shortcut key can implement the insert. Shineway Technologies, Inc. 26

27 4.5. Error Insert Test For error insert test, see Figure 4-6 as follows: Figure 4-6 Error Insert Test Start time refers to the time of system when the Start shortcut key is clicked on. Duration is continual time keeping after Start time. After the running start, the start button changes to the exit button. Click on the exit button to step the time keeping and running. Insert mode : rate (default parameter) 1.0E-3, 1.0E-4, 1.0E-5, 1.0E-6, 1.0E-7, 1.0E-8, 1.0E-9, with a default value of 1.0E-3. Burst scope of setup , with a default value of Repetitive burst scope of setup , with a default value of Insert error : Line ECOD. Insert mode can be rate, burst and repetitive burst. PDH EFAS, ECRC, REBE. Insert mode is continual, with a default value of EFAS. SDH (default parameter) B1 (the maximum value of burst or repetitive burst is 8000), B2 (the maximum value of burst or repetitive burst is 8000), msrei (the maximum value of burst or repetitive burst is 2000), hpb3 (the maximum value of burst or repetitive burst is 8000), hprei (the maximum value of burst or repetitive burst is 8000), lpb3 (the maximum value of burst or repetitive burst is 8000), lprei (the maximum value of burst or repetitive burst is 2000), lp3rei (the maximum value of burst or repetitive burst is 8000), BIP2 (the maximum value of burst or repetitive burst is 2000). Insert mode can be rate, burst and repetitive burst, with a default value of B1. Pattern EBIT. Insert mode can be rate, burst and repetitive burst. The Set shortcut key can set up all the input values or parameters. Once it is set up, Insert mode changes to the current mode (insert error code) instead of the original mode with a display on the upper part of the screen. Then, the Insert shortcut key can implement the insert. Error insert function is unavailable in PDH test mode. Shineway Technologies, Inc. 27

28 4.6. Insert Alarm For insert alarm, see Figure 4-7 as follows: Figure 4-7 Insert Alarm Start time refers to the time of system when the Start shortcut key is clicked on. Duration is continual time keeping after Start time. Click on the exit button to stop. Insert mode : continual. Insert alarm : Line LOS, AIS. PDH LOF, RAI, CRCL, MAIS, CASL, MRAI. SDH (default parameter) EFAS, LOF, OOF, msais, msrdi, auais, hprdi, hpplm, hpuneq, tuais, tulom, lprfi, lprdi, lpplm, lpuneq, tulop, rstim, hptim, lptim, with a default value of EFAS. The Set shortcut key can set up all the input values or parameters. Once it is set up, Insert mode changes to the current mode (insert alarm) instead of the original mode with a display on the upper part of the screen. Then, the Insert shortcut key can implement the insert. Insert alarm function is unavailable in PDH test mode Pointer Adjusting Test For pointer adjusting test, see Figure 4-8 as follows: Shineway Technologies, Inc. 28

29 Figure 4-8 Pointer Adjusting Test Start time refers to the time of system when the Start shortcut key is clicked on. Duration is continual time keeping after Start time. Click on the Start shortcut key again to stop. Insert mode : repetitive burst, scope of setup AU , TU , TU , with a default value of 500. Pointer event : AU +PJ, AU PJ, AU INV, TU +PJ, TU PJ, TU INV. The Set shortcut key can set up all the input values or parameters. Once it is set up, Insert mode changes to the current mode (insert pointer) instead of the original mode with a display on the upper part of the screen. Then, the Insert shortcut key can implement the insert. The default value is AU+PJ. Shineway Technologies, Inc. 29

30 5. Function Test Function test including: APS test, transparency test, TCM test, RTD test and tributary scan test. See Figure 5-1 as follows: 5.1. APS Test Figure 5-1 Function Test For APS test, eee Figure 5-2 as follows: Figure 5-2 APS Test Trigger : MS-AIS, AU-AIS, TU-AIS, B1, and B2, with a default value of MS-AIS. Switching time : with a unit of sec, real-time reception and display in the interface. The Set shortcut key can set up all the input parameters of Trigger. Test starts immediately once in the menu, with the display of results in Switching time and Status column. Pay attention to the interlocking with Start shortcut key. Shineway Technologies, Inc. 30

31 5.2. Data Path (Transparency) Test For data path test, see Figure 5-3 as follows: Figure 5-3 Transparency Test Trans OH : D1-D3, D4-D12, E1, E2, F1 and None, with a default value of None. Trans Pat : 2E11, 2E15, 2E20 and 2E23, with a default value of 2E11. Rec. OH : D1-D3, D4-D12, E1, E2, F1 and None, with a default value of None. Rec. Pat : 2E11, 2E15, 2E20, and 2E23, with a default value of 2E11. In data transparency test and SDH path test, PRBS insert type in interface setup menu includes an additional None option to realize the interlocking of both interfaces. That is to say, the receiving terminal or/and transmission terminal of both must be None. The last select is applied as the final parameter of inserting PRBS and can be set up by Set key. The Set shortcut key can set up all the input values or parameters TCM Test For TCM test interface, see Figure 5-4 as follows: Shineway Technologies, Inc. 31 Figure 5-4 TCM Test

32 Err Mode : Rate (default parameter) 1.0E-3, 1.0E-4, 1.0E-5, 1.0E-6, 1.0E-7, 1.0E-8 and 1.0E-9, with a default value of 1.0E-3. Outburst scope of setup , with a default value of Repetitive burst scope of setup , with a default value of None. Err Position : LP, HP, with a default value of HP. Err Event : tcrei, tcoei, tciec, with a default value oftcrei. The maximum value of burst or repetitive burst is as follows. The maximum value of burst or repetitive burst Type of error code HP VC3 LP VC12 LP tcrei tcoei tciec Table 5-1 List of the Maximum Values of Burst or Repetititve Burst of Error Code Alm Mode : continual, None (default parameter). Alm Position : LP, HP, with a default value of HP. Alm Event : tcunq, tcltc, tcrdi, tcodi, tctim, tcais, with a default value of oftcunq. Add None into the error code and alarm mode for inserting TCM respectively, and realize the interlocking. The last select is applied as the final parameter for inserting TCM and is set up by Set key. The Set shortcut key can set up all the input values or parameters RTD Test RTD includes SDH test and PDH test, with test interface as in Figure 5-5: Figure 5-5 RTD Test Shineway Technologies, Inc. 32

33 Start time refers to the time of system when the Start shortcut key is clicked on. Duration is continual time keeping after Start time. Click on the Exit shortcut key to stop. Current : indicating the measuring result of current RTD. Offset : scope of setup , with a unit of us, and moreover, Set Offset can be added with the value of Current. Set Offset : add Current to Offset. State : measuring, and measured. Pat : indicating current alarm status of SYNC, AIS, EBIT and SLIP. Test starts once in the menu, with a display of test result in Current and State column. Pay attention to the interlocking with the Start shortcut key Tributary Scan Test For tributary scan test, see Figure 5-6 as follows: Figure 5-6 Tributary Scan Test Tributary scan : 1-63 and *(when the receiving part of Test configuration is E1 or VC12), 1-3 (when the receiving part of Test configuration is E3 or C3). TUG3 : 1-3 and *, TUG2 : 1-7 and *, TU12 : 1-3 and *(when the receiving part of Test configuration is E1 or VC12). Click on the Scan shortcut key to enter the scan result interface directly. The default value is to select all. Shineway Technologies, Inc. 33

34 6. Test Result The test result includes alarm test result, error code test result, pointer test result, overhead test result, TCM test result, transparency test result, frequency test result and tributary test result, with the interface as in Figure 6-1. All test result menus have a save function. Click on the Save shortcut key to save up the current test results. Figure 6-1 test result 6.1. Alarm Test Result For alarm test result interface, see Figure 6-2 as follows: Figure 6-2 Alarm Test Result Alarm type : PDH part: including continual seconds of LOS, AIS, LTI, LOF, RAI, CRCL, MAIS, CASL, MRAI, Shineway Technologies, Inc. 34

35 Pat AIS and Pat LSS. (Only in E1 mode) SDH part: including LOS, LOF, RS TIM, MS AIS, MS RDI, AU AIS, AU LOP, HP UNEQ, HP RDI, HP TIM, HP PLM, LTI, Pat AIS, Pat LSS, TU AIS (grey when set up as C4), TU LOP (grey when set up as C4), LP UNEQ (grey when set up as C4), LP RDI (grey when set up as C4), RFI (grey when set up as C3 or C4), LP TIM (grey when set up as C4) and LP PLM (grey when set up as C4). In any interface, click on the Start shortcut key to start synchronous counting and operation. Click on Stop button to stop. Click on the Chart shortcut key to generate a dynamic histogram of alarm test results in this interface directly Error Code Test Result For error code test result interface, see Figure 6-3 as follows: Figure 6-3 Error Code Test Result Error type : PDH part: including error code counting, sec & rate of ECOD, EFAS, ECRC, REBE and EBIT. (Only in E1 mode) SDH part: including error code counting, sec & rate of B1, B2, MRAI, HP B3, LP B3 (grey when set up as C12 or C4), HP REI, LP REI (grey when set up as C4), EBIT and BIP2 (grey when set up as C3 or C4). In any interface, click on the Start shortcut key to start synchronous counting and operation. Click on the exit button to stop. Click on the Chart shortcut key to generate a dynamic histogram of error test results in this interface directly Pointer Test Result For pointer test result interface, see Figure 6-4 as follows: Shineway Technologies, Inc. 35

36 Figure 6-4 Pointer Test Result Pointer test result including: pointer value and SS BITS value of AU and TU, and counting and rate of +AUP JE, -AUP JE, AU NDF, AU INV, +TUP JE, -TUP JE, TU NDF and TU INV. In any interface, click on the Start shortcut key to start synchronous counting and operation. Click on Stop button to stop. Click on the Chart shortcut key to generate a dynamic histogram of alarm test results in this interface directly Overhead Test Result For overhead test result interface, see Figure 6-5 as follows: Figure 6-5 Overhead Test Result Overhead test result including: RS: A1, A2, J0, B1, E1, F1, D1, D2, D3 AU: H1, V1, V2, H2, L1, L2, H31, H32, H33 MS: B2, K1, K2, D4, D5, D6, D7, D8, D9, D10, D11, D12, S1, Z1, Z2, M1, E2 TU12: V1, V2, V3, V4 LOPOH: V5, J2, N2, K4 HOPOH: J1, B3, C2, G1, F2, H4, F3, H4, F3, K3, N1 All results aren t controlled by the shortcut key. Real-time reception and display are available Shineway Technologies, Inc. 36

37 once in the interface. Click on the Stop button to stop TCM Test Result For TCM test result interface, see Figure 6-6 as follows: Figure 6-6 TCM Test Result The display of the number, error code sec and rate of TC-REI, TC-OEI and IEC of N1 and N2 in the overhead of high-order & low-order and the duration of TC-UNO, TC-LTC, TC-RDI, TC-TIM, TC-AIS is available. All results aren t controlled by the shortcut key. Real-time reception and display are available once in the interface. Click on the Stop button to stop Data Path Test (Transparency) Result For data path test result interface, see Figure 6-7 as follows: Figure 6-7 Transparency Test Result The display of the number, error code sec & rate of EBIT and the alarm time of LSS is available. All results aren t controlled by the shortcut key. Real-time reception and display are available Shineway Technologies, Inc. 37

38 once in the interface. Click on the Stop button to stop Frequency Test Result For frequency test result, see Figure 6-8 as follows: Figure 6-8 Frequency Test Result Rev Pat : PRBS code pattern of the receiving part in setup menu. Send Pat : PRBS code pattern of the transmitting part in setup menu. Frequency : actual frequency for receiving, with a unit of bit/s. Offset : the offset between actual receiving frequency and ideal frequency (155.52Mb/s), with a unit of ppm. Minimum : the minimum value of the frequency measured in the interface, with a unit of bit/s. Maximum : the maximum value of the frequency measured in the interface, with a unit of bit/s. All results aren t controlled by the shortcut key. Real-time reception and display are available once in the interface. Click on the Stop button to stop Tributary Test Result For tributary test result interface, see Figure 6-9 as follows: Figure 6-9 Tributary Test Result Shineway Technologies, Inc. 38

39 The display of tributary scan results of VC12 (E1), VC3 (E3) and VC4 (E4) (specified according to setup mode of the receiving part in setup menu) is available. Real-time reception and display are available once in the interface. Click on the Stop button to stop. Shineway Technologies, Inc. 39

40 7. System Setup For the main item of system setup, see Figure 7-1 as follows: 7.1. File Management Figure 7-1 System Setup The file management includes configuration file and result file as in Figure 7-2. Figure 7-2 File Management Configuration File: The configuration parameter of nine modes is available. Click on a file, press the configuration parameter of the file and enter the configuration interface directly as in Figure 7-3: Shineway Technologies, Inc. 40

41 Figure 7-3 Configuration File Result File Ten test results are available as in Figure 7-4: Figure 7-4 Result Test Interface 7.2. Version Information View the version information of the current software and hardware as in Figure 7-5 as follows: Figure 7-5 Version information Shineway Technologies, Inc. 41

42 7.3. Recover Default Recover the system to the default setup as in Figure 7-6: Figure 7-6 Default Recovery 7.4. Time Setup Set up the time of system as in Figure 7-7: Figure 7-7 Time Setup Date : YYYY , MM 1-12, DD Time : HH 1-23, MM 0-59, SS Touch Screen Calibration Click on the below-left corner of screen and then, the screen will prompt to click on the up-right corner to calibrate the screen as in Figure 7-8 as follows: Shineway Technologies, Inc. 42

43 Figure 7-8 Touch Screen Calibration Interface 7.6. Other Setup See Figure 7-9 as follows: Figure 7-9 Other Setup Interface Save Mode : manual save, save once error interval, and timing save, with a default value of Manual. Save duration : 5 minute, 15 minute, 30 minute and 1 hour, with a default value of 5minute. KeyPressSound : On, Off, with a default value of On. Alarm Sound : On, Off, with a default value of On. Contrast : Always on, Automatic, with a default value of Auto Performance Objectives Set up the indicators of the performance test as in Figure 7-10: Shineway Technologies, Inc. 43

44 7.8. USB Connection Figure 7-10 Performance Objectives USB will connect the instrument with PC via USB port for file loading and software update of the instrument as in Figure 7-11 as follows: Figure 7-11 Terminal Wiring Diagram Contacting Customer Service Please check our web site ( for updates to this manual and additional application information. If you need technical or sales support, please contact local Shineway Technologies Customer Service. Shineway Technologies (China), Inc.: Address: Fl.7, Zhongtai Plaza, No.3 Shuangqing Rd, Haidian District, Beijing, China Postal code: Tel: Fax: WEB: Shineway Technologies, Inc. 44

45 THANK YOU FOR CHOOSING SHINEWAY TECHNOLOGIES! Shineway Technologies, Inc. 45