EMD-100 ELECTRIC DISPERSER

Transcription

1 EMD-100 ELECTRIC DISPERSER OWNERS MANUAL EMD-100 ELECTRIC DISPERSER Warranty: Our products are guaranteed against defective materials and workmanship. We will repair or replace such items as may prove defective at our option. Warranty period is one year on items manufactured by FAWCETT. On items not manufactured by FAWCETT, the manufactures warranty applies. All component parts of our products are covered by this warranty, except for normal wear items such as impellers. We cannot be responsible fordamage or abuse to equipment caused by improper installation or operation. Warranties can also be voided by unauthorized disassembly of equipment. For warranty repairs, equipment is returned to FAWCETT at the customer's expense; we will repair and return to customerat our expense.under no circumstances will we allow labor charges or other expense to repair defective merchandise. This warranty is exclusive and is in lieu of all other warranties, whether express or implied. FAWCETT shall not be liable for any other damages, whether consequential, indirect, or incidental, arising from the sale or use of its products. Contents: Model Drawing Data 2 Safety & Receiving 3 Installation 4 Operation 5 Parts Lists 6 Order Form Survey FAWCETT CO., INC Congress Pkwy. Richfield, OH phone: fax: Page:

2 ELECTRIC DISPERSER Model: EMD-100 Date: Order No.:_ Motor: Shaft(s): Part No.: MUD1001ac H.P.:.5 max Part # s : DSB-12 RPM: 0 10,000 Repair Kit #: N/A Accessories: Dart Controller CH-1-C Container Holder Dispersrs: Part # s : MF-23D/F MF-33D/F FAWCETT, Inc. LS manual 03/06

3 Safety Please follow the below safety precautions. If there are any questions, please call FAWCETT at Please read this complete manual before trying to operate your disperserer. Failure to follow these instructions could result in serious bodily injury or death. Do not touch moving parts while disperser is operating. Do not wear loose-fitting clothes or jewelry around an operating disperser. Keep all hands, feet, clothes, neckties, necklaces and other objects clear of moving parts. Never move the unit with the motor running. Never run the unit in open air. Never adjust the speed without the unit running. WARNING: THIS MOTOR IS NOTEXPLOSION PROOF!! Use only around non-flammable materials, or where adequate ventilation exists, such as in a fume hood, to draw off flammable vapors WARNINGS: Always unplug the machine prior to changing the blade DO NOT wear loose clothing or long hair around rotating machinery. For example: it would only take.03 seconds to wrap 18 of hair or a loose necktie around the shaft when the machine is operating at full speed!!! Receiving: Before removing any packing, visually inspect the exterior of the shipment for any sign of damage. Should there be any damage, bring it to the attention of the delivering UPS or truck line and note the same on the receiving ticket. Should there be damage you must place a claim with the truck line. They are the only ones who will pay for the damage done and you are the only one who can place that claim. FAWCETT, Inc. LS manual 6/15/2006 page 3 of 7

4 Installation Your new disperser is supplied partially assembled. For more information, see the parts list pages for general arrangement drawings. Dispersers: To install the disperser blade, remove one of the jam nuts. Insert the disperser blade onto the shaft. Assemble and tighten the second jam nut firmly to secure the disperser blade to the shaft. Disperser Blade Placement: Experimenting with disperser blade placement may provide your best results. Assembly: STEP #1: Install the container holder, onto the bottom of the support.install short end (below collar) of 36 long aluminum support rod into base and tighten set screw in base securely using supplied allen wrench. STEP #2: Slide motor and support clamp assembly onto support rod until shaft collar is reached. STEP #3: Slide dispersion shaft into the ½ chuck and tighten with supplied key. Tighten securely so the shaft cannot work loose. STEP #4: If necessary, reposition motor stop collar on support rod to correct minimum operating height. STEP #5: Plug motor cord into variable speed controller. DO NOT plug motor directly into wall power outlet. STEP #6: Making sure variable speed controller is OFF, and speed control is set to ZERO, plug controller into a 110 VAC wall outlet. STEP #7: Install disperser blade on to end of the dispersion shaft between the supplied jam nuts. STEP #8: Verify motor support clamp has been tightened to support bar. Unit is now ready to operate. FAWCETT Co, Inc. LS manual 03/06 page 4 of 7

5 OPERATING INSTRUCTIONS Note: Periodically check dispersion shaft chuck for tightness prior to starting Machine. Trial and error will determine the best height position for the dispersion impeller, which will depend on the mixing container size you are using, but as a rule of thumb, the impeller should be no closer than 1 to the bottom of the mix container, and optimally should be about 1½ times the blade diameter in height off the bottom. For example, if the impeller diameter is 2, the blade will work best about 3 off the bottom. Always start and stop the machine in low speed. Turning on the machine at higher speeds is not recommended, as it may damage the motor, or more likely, the sudden start will sling the material being mixed. Optimum operating speed is viscosity dependent. The more viscous the material is, the slower the machine needs to run to achieve dispersion speed. For example, a 5000 CPS paint base may need FPM impeller peripheral tip speed to achieve dispersion; a less viscous material may need higher tip speed. You may run up to a 3 diameter impeller on this machine. Larger diameter impellers may damage the motor. Peripheral tip speed may be calculated with the following equation: (IMPELLER DIAMETER in inches) x (.262) x (RPM) = Tip speed in Feet Per Minute (FPM). Thus, for a 2 diameter impeller, 10,000 RPM = 5240 FPM and 5000 RPM 2620 FPM Note: This air cooled motor can get HOT, especially if run at lower speeds under heavy load. Always be cautious when grasping motor to raise it Thank you for purchasing a Fawcett mixer. 1FAWCETT, Inc. LS manual 03/06 Page 6 of 7

6 PHONE: FAX: EMD100 DESCRIPTION C1 SUPPORT STAND A1 STAND ROD 3 03J CHUCK / COUPLING B1 MOTOR MOUNT 5 L-10 CLAMP BLOCK 6 MUD1001AC MOTOR 7 253G-200E MOTOR CONTROLLER K41 HANDLE 9 CH-1-C CONTAINER HOLDER 10 MF-23D/F 2 DISPERSER BLADE 11 MF-33D/F 3 DISPERSER BLADE 12 SB-12T DISPERSER SHAFT K25 SHAFT COLLAR REF. CK-1 CHUCK KEY FAWCETT CO., INC. LS manual 03/06 Page 7 of 7

7 FAX FEEDBACK SHEET Our objective is to provide you the best products possible. You may help us by providing feedback to us. Please complete this survey and fax it back to us within 10 days. Shipment No.: Shipment Date: _ Please circle your responses and FAX to (330) If you are RECEIVING or PURCHASING personnel, please answer the following: Was this shipment received within the timeframe established by your company? YES NO Did this shipment contain the correct items and quantity? YES NO Was the box damage free? YES NO Does the level of product quality meet your requirements and expectations? YES NO Are you aware of our website? YES NO If you are TECHNICAL personnel, please answer the following: Did you need to contact our Technical Support staff? YES NO If you did contact us, was our staff helpful and professional? YES NO Did you use the installation, programming and/or hookup instructions? YES NO Were the installation, programming and/or hookup instruction clear for you? YES NO Completed By: Your Function: Company: City, State, Zip: _ Phone: _ Thank you for helping us continually improve the products and services we provide you. For more detailed feedback, feel free to contact our Customer Service Personnel at (330) ext.2300 or via at sales.service@fawcettco.com Fawcett Co., Inc. The Home of Mixed Flow Impellers * Manufactured in the USA *

8 FAWCETT CO., INC. PHONE: Congress Pkwy. FAX: Richfield OH ORDER FORM Person Placing Order : Phone # : P.O. # : FAX # : SHIP TO: BILL TO: Attention Attention Location Location Street Address Street Address City State Zip City State Zip Req. Date Requesitioner Ship Via Buyer F.O.B. Terms Richfield, OH NET 30 Days Quantity Item Description Unit Price Total Subtotal Sales tax will be added to deliveries in the state of Ohio unless a tax exempt certificate is on file. All orders are F.O.B. shipping point. Shipping charges will be added to invoice. Tax Shipping Miscellaneous Balance Due