UNITE 200 CAMERA USER GUIDE

Transcription

1 UNITE 200 CAMERA USER GUIDE NOTE: For the UNITE 200 camera s control, use the COLLABORATE Codec Appliance s remote control. The remote control that comes with this camera is only for advanced configurations, if required.

2 2 UNITE 200: User Guide

3 COPYRIGHT NOTICE ClearOne 5225WileyPostWay Suite500 SaltLakeCity,UT84116 Telephone TechSales FAX On the Web Unite 200 USER GUIDE CLEARONE DOCUMENT DOC REV 1.1 Mar ClearOne Inc. - All rights reserved. No part of this document may be reproduced in any form or by any means without written permission from ClearOne. Printed in the United States of America. ClearOne reserves specific privileges. Information in this document is subject to change without notice. NOTICE: This Class A device complies with Part 15 of the FCC rules and Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. UNITE 200: User Guide 3

4 CONTENTS PREFACE... 5 PRECAUTIONS... 5 SUPPLIED ACCESSORIES... 6 QUICK START... 7 FEATURES... 9 PRODUCT SPECIFICATION MAIN UNIT SIZE IR REMOTE CONTROL SERIAL COMMUNICATION CONTROL MENU SETTING IP FUNCTION USB MAINTENANCEAND TROUBLESHOOTING UNITE 200: User Guide

5 PREFACE This manual introduces the function, installation, and operation of the UNITE 200 camera. Prior to installation and usage, please read the manual thoroughly. PRECAUTIONS This product can be used only under the specified conditions in order to avoid any damage to the camera: Don t subject the camera to rain or moisture. Don t remove the cover; otherwise, you may get an electric shock. In case of abnormal operation, contact ClearOne Technical Support. Never operate outside the specified temperature, humidity, and power supply recommendations. Use a soft dry cloth to clean the camera. If the camera is very dirty, clean it with diluted neutral detergent; do not use any type of solvents, which may damage the surface. Caution to transport Avoid stress, vibration, and moisture in transport, storage and installation. During installation, take the following precautions: Do not grasp the camera by the head when carrying the camera. Don t turn camera head manually. Doing so may result in mechanical damage. Don t apply corrosive liquid, gas or solid, to avoid damaging the cover which is made up of plastic material. Make sure there are no obstacles within the camera s rotation range. Never power on before installation has been completed. Don t dismantle the camera ClearOne is not responsible for any unauthorized modification or dismantling. 5 UNITE 200: User Guide

6 SUPPLIED ACCESSORIES When you unpack, check that all the supplied accessories are included: Camera AC power adapter Power cord RS232 cable Remote controller User manual USB3.0 Cable 6 UNITE 200: User Guide

7 QUICK START Step 1. Please ensure connections are correct before starting Step 2. Setting of the bottom switches Set both of the switch1 and switch2 to OFF. That is Normal Working Mode. SW-1 SW-2 Mode 1 OFF OFF Normal Working Mode 2 ON OFF - 3 OFF ON - 4 ON ON - 7 UNITE 200: User Guide

8 Step 3. Set the Video System Switch to the desired setting Video format options: VIDEO SYSTEM p p p p i60 A i50 B p60 C p50 D p30 E p25 F - NOTE: After changing the switch, you need to restart the camera to take effect. Step 4. Press the ON/OFF button to turn on the camera. Step 5. When the camera starts, Pan-Tilt rotates to the maximum position of top right, then it returns to the center position. The initialization process is finished. NOTE: If the position preset 0 has been stored, the position preset 0 will be called up after initialization. See IR Remote Control later in this manual for information about setting presets. Step 6. (Optional) If you want to restore the factory default settings, Press the Menu button to display the On-screen Display (OSD) menu. Select the item Menu >Restore Default > Restore. Set the value Yes, and then press the HOME button to restore the factory default settings. 8 UNITE 200: User Guide

9 FEATURES 72.5 Wide-angle Lens 72.5 wide-angle,high-quality lens; supports 12x optical zoom. USB 3.0 USB3.0 ultra-high speed interface; can transfer uncompressed original video, and downward compatible with USB2.0. The USB, HDMI, and Network interfaces can output at the same time. AAC Audio Encoding Supports audio line input. Supports AAC audio encoding, for better sound quality and lower bandwidth. H.265 Support Supports H.265 encoding, enabling full HD 1080p/60fps video stream at ultra-low bandwidth. 1080P Full HD A 1/2.7 inch, 2.07 million effective pixels high quality HD CMOS sensor, can reach maximum 1920 x 1080 resolutions, achieving a high quality image. Ultra-high Frame Rate Output frame rate up to 60fps in1080p. Low-light High SNR of CMOS sensor, combined with 2D and 3D noise reduction algorithm, effectively reduces the noise, even under low illumination conditions, to ensure that the picture can still remain clean and clear. Serial Interface Control All the parameters of the camera can be remotely controlled using the RS232/485 interface. 9 UNITE 200: User Guide

10 PRODUCT SPECIFICATION Details Model UNITE 200 Name UNITE Full-HD Video Conference Camera Camera Video System HD: 1080p/60, 1080p/50, 1080i/60, 1080i/50, 1080p/30,1080p/25, 720p/60, 720p/50, 720p/30, 720p/25 Sensor 1/2.7 inch, CMOS, Effective Pixel: 2.07M Scanning Mode Progressive Lens 12x, f3.5mm mm, F1.8 - F2.8 Minimal Illumination 0.05 (F1.8, AGC ON) Shutter 1/30s - 1/10000s White Balance Backlight Compensation Digital Noise Reduction Video S/N Auto, Indoor, Outdoor, One Push, Manual Support 2D&3D Digital Noise Reduction 55dB Horizontal Angle of View Vertical Angle of View Horizontal Rotation Range ±170 Vertical Rotation Range Pan Speed Range Tilt Speed Range H & V Flip Image Freezing /s /s Support Support Number of Presets 255 Preset Accuracy 0.1 USB Features Operating System Color System YUV 4:2:2 Windows 7,Windows 8,Windows 8.1,Windows 10, Mac OS X,Linux 10 UNITE 200: User Guide

11 Video Format USB3.0 : 1080p/30, 1080p/25, 720p/30, 720p/25 USB Video Communication Protocol UVC PTZ Network Features UVC1.0 Support Video Compression Video Stream Main Stream Resolution Sub Stream Resolution Video Bit Rate Bit Rate Type Frame Rate Audio Bit Rate Support Protocols H.265/H.264/MJPEG Main Stream, Sub Stream 1920x1080, 1280x720, 1024x x576, 720x480, 320x Kbps Kbps Variable Rate, Fixed Rate 50Hz: 1fps - 50fps, 60Hz: 1fps - 60fps 96Kbps, 128Kbps, 256Kbps TCP/IP, HTTP, RTSP, RTMP, DHCP, Multicast, etc. Input/ Output Interface HD Output 1xHDMI: Version 1.3 Network Interface Audio Interface 1xRJ45: 10M/100M Adaptive Ethernet port 1-ch: 3.5mm Audio Interface, Line In USB Communication Interface 1xUSB3.0: Type B female jack Power Jack JEITA type (DC IN 12V) Generic Specification 1xUSB2.0: Type A female jack(reserved Interface) 1xRS-232 IN: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA/Pelco-D/Pelco-P 1xRS-232 OUT: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA network use only 1xRS485: Share with RS232 Out, Max Distance: 1200m, Protocol: VISCA/Pelco-D/Pelco-P Input Voltage Current Consumption DC 12V 1.5A (Max) Operating Temperature -10 C - 40 C Storage Temperature -40 C - 60 C 11 UNITE 200: User Guide

12 Power Consumption Dimensions Weight 12W (Max) 240mm x 144mm x 160mm 1.65Kg (3.6lb) MAIN UNIT 1. Lens 11. RJ45 Interface 2. Sensor for the Remote Control 12. Reserved Interface 3. Power Lamp 13. Line In Interface 4. Standby Lamp 14. Reserved Interface 5. Bottom Switches 15. HDMI Interface 6. Tripod Screw Hole 16. USB Fixing Screw Hole 17. Reserved Interface 8. System Select Switch 18. DC IN 12V Interface 9. RS232 OUT Interface 19. POWER Switch 10. RS232 IN Interface 12 UNITE 200: User Guide

13 SIZE Unit: inch 13 UNITE 200: User Guide

14 IR REMOTE CONTROL 0. Standby Button Press this button to enter standby mode. Press it again to enter normal mode. NOTE: Power consumption in standby mode is approximately half of the normal mode. 1. Position Buttons To set preset or call preset 2. * Button 3. Set/Clear Preset Buttons Set preset: Store a preset position [SET PRESET] + Numeric button (0-9): Setting a corresponding numeric key preset position NOTE: Preset 0-9 via remote control and the rest from web, keyboard and the serial port. Clear preset: Erase a preset position [CLEAR PRESET] + Numeric button (0-9), Or: [*] + [#] + [CLEAR PRESET]: Erase all presets 4. BLC (Backlight Compensation) Button BLC ON/OFF: Press this button to enable the backlight compensation. Press it again to disable the backlight compensation. NOTE: Effective only in auto exposure mode. NOTE: If there is a light behind the subject, the subject will appeardark. In this case, press the backlight ON / OFF button. To cancel this function, press the backlight ON / OFF button. 14 UNITE 200: User Guide

15 5. Focus Buttons Used for focus adjustment. Press [AUTO] to adjust the focus on the center of the object automatically. To adjust the focus manually, press the [MANUAL] button, and adjust it with [Focus+] (focus on far object) and [Focus-] (focus on near object). 6. Camera Select Buttons Press the button corresponding to the camera you want to operate with the remote control. 7. # Button 8. Pan/Tilt Control Buttons Press the arrow buttons to perform panning and tilting. Press the [HOME] button to face the camera back to front. 9. Menu Setting Menu button: Press this button to enter or exit the OSD menu. 10. Zoom Buttons Zoom : Zoom In Zoom : Zoom Out 11.Multiple Function Buttons Function 1. Set camera IR address Press 3 keys contiguously can set camera IR address as follow: [*] + [#] + [F1]: Address1 [*] + [#] + [F2]: Address2 [*] + [#] + [F3]: Address3 [*] + [#] + [F4]: Address4 Function 2. Image freezing function Press [F4] to start the freeze function. The word "Freeze" displays on the upper left corner. After five seconds, the display disappears automatically (though the freeze feature continues). To cancel the freeze, press the [F4] key the word "Unfreeze" displays on the upper left corner. After five seconds, the display 15 UNITE 200: User Guide

16 disappears automatically. Shortcut Set Function [*] + [#] + [1]:Display OSD menu in English [*] + [#] + [3]: Display OSD menu in Chinese [*] + [#] + [4]: Show IP address [*] + [#] + [6]: Quickly restore the default settings [*] + [#] + [8]: Show the camera version [*] + [#] + [9]: Quickly set mount mode (flip / normal) 16 UNITE 200: User Guide

17 SERIAL COMMUNICATION CONTROL In default working mode, the camera can be controlled via RS232 or RS485 (half-duplex mode). The parameters are as follows: Baud rate: 2400/4800/9600 bit/s. Start bit: 1 bit. Data bit: 8 bits. Stop bit: 1bit. Parity bit: none. When the camera initializes, Pan-Tilt rotates to the maximum position of top right, then it returns to the center, and the process of initialization is finished. (Note: If the position preset 0 has been stored, the position preset 0 is called up after initialization.) Then the users can control the camera with commands in the command list. Control interface definition No. Function 1 DTR 2 DSR 3 TXD 4 GND 5 RXD 6 RS485-7 IR OUT 8 RS UNITE 200: User Guide

18 CameraWindows DB-9 Camera In Camera Out 1. DTR 1.CD 1. DTR 1.DTR 2. DSR 2.RXD 2. DSR 2.DSR 3.TXD 3.TXD 3. TXD 3.TXD 4.GND 4.DTR 4. GND 4.GND 5.RXD 5.GND 5. RXD 5.RXD 6.RS485-6.DSR 6. RS485-6.GND 7.IR OUT 7.RTS 7. IR OUT 7.NC 8.RS CTS 8. RS NC 9.RI Network configuration Under VISCA Under Pelco-D/P Commandlist The camera uses the VISCA/Pelco-D/Pelco-P serial standard. If you need VISCA/Pelco-D/Pelco-P protocol command list in detail, please contact ClearOne Technical Support. 18 UNITE 200: User Guide

19 MENU SETTING 1. MENU Press the [MENU] button to display the main menu. Use the arrow buttons to select the item to be set. Press the [HOME] button to enter a sub-menu. EXPOSURE Mode Auto ExpCompMode Off Backlight Off Gain Limit 3 Anti-Flicker 50Hz DRC 6 MENU Exposure Color Image P/T/Z Noise Reduction Setup Restore Default [Home] Enter [Menu] Exit 2. EXPOSURE Select Exposure from the main menu and press the [HOME] button. The EXPOSURE menu appears, as shown in the following figure: Select Item Change Value [Menu] Back Mode: Exposure mode. Options: Auto, Manual, SAE, AAE, Bright. ExpCompMode (Effective only when exposure mode is Auto): Exposure compensation mode. Options: On, Off. ExpComp (Effective only when ExpCompMode is On): Exposure compensation value. Options: Gain Limit (Effective only when exposure mode is Auto/AAE/Bright): Maximum gain limit. Options: Backlight (Effective only when exposure mode is Auto): Set the backlight compensation. Options: 19 UNITE 200: User Guide

20 On, Off. DRC: Dynamic range control strength.options: 0-8. Bright (Effective only when exposure mode is Bright): Exposure bright level, Options: Anti-Flicker (Effective only when exposure mode is Auto/Bright): Options: Off, 50Hz, 60Hz. Iris (Effective only when exposure mode is Manual / AAE): Aperture value. Options: F1.8, F2.0, F2.4, F2.8, F3.4, F4.0, F4.8, F5.6, F6.8, F8.0, F9.6, F11.0, Close. Shutter (Effective only when exposure mode is Manual /SAE): Shutter value. Options: 1/30,1/60, 1/90,1/100,1/125,1/180,1/250,1/350, 1/500,1/725,1/1000,1/1500,1/2000,1 /3000,1/4000,1/6000,1/ COLOR Select Color in the main menu and press the [HOME] button. The COLOR menu appears, as shown in the following figure: COLOR WB Mode Auto RG Tuning 0 BG Tuning 0 Saturation 90% Hue 7 AWB sens Low Select Item Change Value [Menu] Back WB-Mode: White balance mode. Options: Auto, Indoor, Outdoor, One Push, Manual. RG (Effective only when WB-Mode is Manual): Red gain. Options: BG (Effective only when WB-Mode is Manual): Blue gain. Options: RG Tuning (Effective only when AWB sens is Low): Red gain fine-tuning. Options: BG Tuning (Effective only when AWB sens is Low):Blue gain fine-tuning. Options: Sat.: Saturation. Options: 60% - 20 UNITE 200: User Guide

21 200%. Hue: Chroma adjustment. Options: 0-14 AWB sens: White balance sensitivity. Options: Normal, High, Low. 4. IMAGE Select Image in the main menu and press the [HOME] button. The IMAGE menu appears, as shown in the following figure: Options: Auto, 0-15 Flip-H: Image flipped horizontally. Options: On, Off. Flip-V: Image flipped vertically. Options: On, Off B&W-Mode: Image color. Options: On,Off Gamma: Options Default, 0.45, 0.5, 0.56, 0.63 Style: Options: Norm, Clarity, Bright, Soft. IMAGE Luminance 6 Contrast 6 Sharpness 1 5. P/T/Z P/T/Z SpeedByZoom On Flip-H Off AF-Zone Center Flip-V Off AF-Sense Low B&W-Mode Off L/R Set STD Gamma Default Style Norm Select Item Change Value [Menu] Back Luminance: Brightness adjustment. Options: 0-14 Contrast: Contrast adjustment. Options: 0-14 Sharpness: Sharpness adjustment. Select Item Change Value [Menu] Back SpeedByZoom: The depth of field scale switch. Options: On, Off AF-Zone:Interested in focusing area. 21 UNITE 200: User Guide

22 Options: Top, Center, Bottom AF-Sense: Automatic focusing sensitivity. Options: Low, Normal, High L/R Set: Options: STD, REV 6. NOISE REDUCTION Select Noise Reduction in the main menu and press the [HOME] button. The NOISE REDUCTION menu appears, as shown in the following figure: NOISE REDUCTION D-HotPixel: Dynamic bad points. Options: Off, SETUP Select Setup in the main menu and press the [HOME] button. The SETUP menu appears, as shown in the following figure: SETUP Language EN DVI Mode DVI Protocol VISCA V_Address 1 NR2D-Level 3 NR3D-Level 4 V_AddrFix Net Mode Off Serial D-HotPixel Off Baudrate 9600 Select Item Change Value [Menu] Back Select Item Change Value [Menu] Back NR2D-Level: 2D noise reduction. Options: Off, Auto, 1-5 NR3D-Level: 3D noise reduction. Options: Off, UNITE 200: User Guide Language: Menu language. Options: EN, Chinese, and Russian DVI Mode: Options: DVI, HDMI. Protocol: Control protocol type. Options: AUTO, VISCA, PELCO-D, PELCO-P V_Address: Protocol address. To be decided according to the

23 agreement,auto, VISCA protocol Options: 1-7 P_D_Address: PELCO-D protocol. Options: P_P_Address: PELCO-P protocol. Options: 0-31 V_AddrFix: The switch you can change camera uart address. Options: On, Off (When set to On, the FF command is invalid.) Net Mode: Set the serial port control networking. Options: Serial, Paral Baudrate: Serial port baud rate. Options: 2400, 4800, RESTORE DEFAULT Select Restore Default in the main menu and press the [HOME] button. The RESTORE DEFAULT menu appears, as shown in the following figure: RESTORE DEFAULT Restore? No Change Value [Home] OK [Menu] Back Restore: Confirm restore factory settings. Options: Yes, No NOTE: Press the [HOME] button to confirm. 23 UNITE 200: User Guide

24 IP FUNCTION 1. Operating Environment Operating System: Windows 7/8/8.1/10 Note: Using the included utility programs requires Windows, but using the Web interface does not require any particular operating system. Network Protocol: TCP/IP 2. Equipment Installation 1) Connect the camera to your network or to your PC directly via an Ethernet cable. Note: To connect the camera directly, use an Ethernet crossover cable. 2) Turn on the camera. 3) If the orange light of internet port is on and the green light is flashing, then the camera is connected to the network or to your computer. 3. Internet Connection Ways to connect the camera and a computer are shown in the figures below: Connect directly by Ethernet crossover cable Connect via router/switch 4. Access the camera though LAN Setup IP address The camera s default IP address is If you forget the camera s IP address, use one of the methods to find the IP address as below: Method 1: press * and # and 4 on the remote control to display the camera IP address on-screen. Method 2: Connect the camera to a PC with an Ethernet cable, and run upgrade_en.exe (contact ClearOne technical support to get this tool) to find the camera s IP address. To change the camera s IP address, use one of the methods as below: 24 UNITE 200: User Guide

25 Method 1: a. Open the camera s Web interface (see Access Camera s Web Interface later in this Manual for detailed instructions). b. On Web interface page, find Network --->Change IP. Enter a new IP address, then Click Apply. c. Restart camera. Method 2: Run upgrade_en.exe, change the IP address, and then click Set. The camera will restart Access camera s web Input into a browser (Internet Explorer and Firefox work best). Note: If you have changed the camera s IP address, enter the new address. Note: To access the camera using an IP address, you must be on the same network as the camera. A login window appears. Input the user name: (default is admin and password (default is admin, as shown below (the login window may not look exactly like this, depending on your operating system and browser) : 25 UNITE 200: User Guide

26 number. For example, set up host computer name as: youdomain.f3322.org, camera port number: 554. Access link would be: VLC stream media player After login, the Web interface appears, as shown below: monitoring VLC media server procedure Open VLC media player, click "Media"->"Open Network Steam", or type Ctrl+N. Input stream address: rtsp://ipaddress:port number/1 (Main stream ). Example: rtsp:// :554/1 NOTE: If this is the first time using the web interface, you must install the VLC player software. 5. Access the camera though WAN Dynamic DNS setup for accessing the camera Once you have set a domain name to camera, and forwarded the traffic to the traffic to the correct address and port number, then you can use a domain name to access camera. Access link: port 26 UNITE 200: User Guide rtsp://ipaddress:port number/2 (Sub stream). Example: rtsp:// :554/2 NOTE:The default RTSP port number is 554.

27 6. IP Camera parameter setup 6.1. Homepage introduction Menu All pages include two menu bars: Real time monitoring: displaying video image Parameter setup: with function buttons Video viewing window Video viewing window must be same as video resolution; the bigger the resolution, the bigger the playing area. Double-click the viewing window to show full-screen; double-click again to return to initialized size. PTZ Setup 1) Pan-Tilt control: Up, Down, Left, Right,Home button as shown above. 2) Rate: Vertical speed can be chosen as 1-24, horizontal direction at the rate of Select corresponding speed and click direction button to realize PTZ speed increase or decrease. 3) Zoom In/ Zoom out: for zooming 27 UNITE 200: User Guide

28 in or zooming out. Focus In/ Focus Out: Focusing on distant objects or Focusing on close objects. 4) Set/Call: When PTZ has been set to a desired position, you can save that configuration as a preset for later use. Click the Set button to save a preset. At any point later, you can click the Call button to call this preset Media For Video Setup, Select "Video". 1) Video format Supports 50HZ (PAL) and 60HZ 28 UNITE 200: User Guide (NTSC), and Dial priority. 2) Encode Protocol Supports H.264 and H ) Encode Level Supports baseline, main profile, and high profile. 4) Resolution Main bit rate supports 1920x1080, 1280x720 and 1024x576. Minor bit rate supports720x480, 720x576and 320x240. The higher the resolution, the clearer the image will be, but more network bandwidth will be used. 5) Bit Rate User can assign bit rate/stream. Generally speaking, the higher bit rate is, and the clearer the image will be. The bit allocation must combine with network bandwidth. If the network bandwidth is too low and the allocated bit rate is too high, the video quality will suffer. 6) Frame rate You can specify the size of the frame rate. Generally speaking, the greater the frame rate, the smoother the image; the smaller the frame rate, the choppier the image.

29 7) I key frame interval: Set interval between 2 I frame. The bigger the interval, lower the response will be from viewing window. 8) Bit Rate control Options: Constant bit rate: video coder will be coding according to preset speed Variable bit rate: video coder will adjust the speed based on preset speed to gain the best image quality 9) Fluctuate level Restrain the fluctuation magnitude of variable rate. Options: Image Setup, Click Image. 1) Brightness Image brightness, 0-14, slider control, on the right shows the corresponding numerical value. The default value is 6. 2) Saturation Saturation 0-14, slider control, on the right shows the corresponding numerical value. The default value is 3. 3) Contrast Contrast 0-14, slider control, on the right shows the corresponding numerical value. The default value is 6. 4) Sharpness Sharpness 0-15, slider control, on the right shows the corresponding numerical value. The default value is 1. 5) Hue Hue 0-14, slider control, on the right shows the corresponding numerical value. The default value is 7. 6) Flip & Mirror Select Flip to turn the image upside down; select Mirror to flip the image horizontally. The default value for both is not selected. 7) Button 29 UNITE 200: User Guide

30 After adjusting any parameters, click Apply to save the settings or click Cancel to cancel the adjustment of the parameters. Click Default to revert to the default value. System 6.4. Audio Setup, Click Audio. 1) Audio Type Option: AAC. 2) Sample rate Options: 44.1K and 48K. 3) Bit rate Options: 96K, 128K, 256K. 4) Input Type Option: line in only 5) Line in: The gain of the Line in. 6) Reserved 7) Apply Button Click "Apply" to save changes, or click "Cancel" to discard the changes System setting, please click 30 UNITE 200: User Guide 1) Work Mode Work Mode RTSP 2) Reboot Click the "Reboot" button to restart the system. 3) User and password You can modify the password (letters and numbers only) 4) Apply / Cancel Modify password and click "Apply" to change the password, or click "Cancel" to cancel password change Network Setting, Click Network.

31 1) LAN Settings The default IP address is The MAC address can be modified. 2) Port Settings HTTP Port, Default port number: 80 RTSP Port, Supports the RTSP protocol. Default port number: 554. PTZ Port, Supports PTZ protocol. Default port number: ) Control Protocol Setting Camera control communication protocols include Visca address, Pelco-D address, and Pelco-P address. 4) RTMP Setting When configuring the camera stream, can set up two streams, in the two stream selection control code stream of "On", "Off", "Video", "Audio", etc. 5) RTSP Setting Setting network camera RTSP protocol of "On", "Off". 6) Multicast Setting Multicast switch, multicast address (default address ) and port (default port number: 6688) can be set. 7) Apply / Cancel Modify network parameters then click "Apply" to save the changes, or click "Cancel" to discard the changes Device Information Click Information, the current device information as shown below. 31 UNITE 200: User Guide

32 USB 3.0 Camera supports UVC protocol, compatible with USB 2.0 & USB 3.0. USB 3.0 supports 1920x1080p/30 max output. Support OS: Windows 7/8/8.1/10, Linux, Mac OS, etc. General software as follows: Windows: AMCAP, VLC, Debut Video Capture, etc. Linux: V412 software driver and VLC media player, etc. Mac OS: FaceTime. ichat, Photo Booth and Debut Video Capture, etc. NOTE: We recommend using AMCAP version 8.0 in Windows, as its software performance is more stable. When using the high version of AMCAP in a low configuration system, it will slow the stream rendering. NOTE: The first time the camera is accessed by USB cable, you must install a plug-in. MAINTENANCEAND TROUBLESHOOTING Camera Maintenance If camera will not be used for a long time, turn off the power switch and disconnect. AC power cord of AC adapter to the outlet. Use a soft cloth to clean the camera cover. Use the soft dry cloth to clean the lens. If the camera is very dirty, clean it with diluted neutral detergent. Do not use any type of solvents, which may damage the surface. Unqualified Application Do not shoot extremely bright objects for a long period of time, such as sunlight, strong light sources, etc. Do not operate in unstable lighting conditions, otherwise image may flicker. 32 UNITE 200: User Guide

33 Troubleshooting Problem Solution No image 1. Check whether the power cord is connected, voltage is OK, POWER lamp is lit. 2. Check whether the camera can self-test after start up. 3. Check the BOTTOM switch and make sure the two switches are both set OFF. 4. Check the video cable to make sure it is connected correctly. Abnormal display of Check the video cable to make sure it is connected correctly. image Image dithering even at widest zoom position IE browser not showing video image 1. Check whether the camera is fixed correctly. 2. Make sure there is nothing nearby causing vibrations. When the camera is accessed the first time by Internet Explorer (or another web browser), you must install the plug-in.the first time you use this camera by internet (only for new user), you must install the player software (VLC). Please go to VLC website and Install VLC (player software). After installation, log in again. You should see the video stream on the home page of the Web interface. Unable to access IP Camera by browser 1. Make sure your computer is connected to the network, to rule out cable failure or network failure caused by a virus. Make sure you can ping the computer from another machine and that the computer you re using can ping other machines on the local network or the gateway. 2. Disconnect the camera from the network, ensure that the camera and PC are connected (either directly, using a crossover cable, or via a router or switch), and then follow the directions earlier in this guide for resetting the IP address. 33 UNITE 200: User Guide

34 3. Check the server's IP address and subnet mask and gateway address. 4. Check for MAC address conflicts. 5. Make sure the HTTP port isn t occupied by other devices, or that routing rules aren t sending the traffic to a different address or port. IP address modified incorrectly or forgot Web interface password The IR remote control cannot control the camera You can recover access to the camera using the IR remote control. Press "[*] + [#] + [Manual]" to restore the default values (default IP: , default username: admin, default password: admin). 1. Change the remote control battery. 2. Check the camera working mode. 3. Check that the IR address of the Remote Commander is set Serial communication correctly. 1. Check the camera working mode. cannot control the 2. Check that the control cable is connected correctly. camera 34 UNITE 200: User Guide