Outdoor/Indoor Receiver/Drivers Installation/Operation Instructions

Transcription

1 V1691 Series Outdoor/Indoor Receiver/Drivers Installation/Operation Instructions This manual applies to below series products: V1691/V1691X/V A/V1691E/ V1691EX/V1691E-24A This manual describes the installation and operation procedures for V1691 Series Receiver/drivers. Compatible with all Infinova series matrix switching systems, V1691 Series Receiver/drivers are designed to perform PTZ, lens zoom in/out, focus, iris, and auxiliary functions at a camera site. A unique camera ID is assigned to each receiver/driver, so the operators could only control the selected camera through the corresponding receiver/driver. V1691 Series Receiver/drivers are classified as a single-channel type since one unit controls only one camera at a site.

2

3 Notice Copyright Statement This manual may not be reproduced in any form or by any means to create any derivative such as translation, transformation, or adaptation without the prior written permission of Infinova. Infinova reserves the right to change this manual and the specifications without prior notice. The most recent product specifications and user documentation for all Infinova products are available on our website Trademarks Infinova is a trademark of Infinova. Copyright Infinova. All rights reserved. All other trademarks that may appear belong to their respective proprietors. FCC Warning V1691 Series Receiver/drivers all comply with Part 15 of the FCC rules. Operation is subject to the following two conditions. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. V1691 Series Receiver/drivers have been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

4 Read this manual carefully before installation. This manual should be saved for future use. Important Safety Instructions and Warnings Electronic devices must be kept away from water, fire or high magnetic radiation. Clean with a dry cloth. Provide adequate ventilation. Unplug the power supply when the device is not to be used for an extended period of time. Only use components and parts recommended by manufacturer. Position power source and related wires to assure they will be kept away from ground and access way. Refer all service matters to qualified personnel. Save product packaging to ensure availability of proper shipping containers for future transportation. Indicates that the un-insulated components within the product may carry a voltage harmful to humans. Indicates operations that should be conducted in strict compliance with instructions and guidelines contained in this manual. Warning: To avoid risk of fire and electric shock, keep the product away from rain and moisture!

5 Table of Contents Chapter I General Description Description Models Features...1 Chapter II Installation Mounting...2 Chapter III System Connections and Setup System Connections Code Source to V1691 Series receiver/drivers Pan/Tilt and Lens Connections Camera Power Connections Setup DIP Switch SW DIP Switch SW Lens Voltage Adjustment Jumper Setting Presets...5 Chapter IV Operation Preparation Powering On Pan/Tilt Lens Control... 6 Appendix I Camera Site ID DIP Switch Settings... 6 Appendix II System Testing... 9 Appendix III Specifications Appendix IV Typical System Connections Connect V2011 to V Connect V2015 to V Connect V2020 to V and V Connect V2116 Keyboard to V Connect Pan/Tilt & Lens to V Connect the camera & Pan/Tilt to V1691(with presets)... 15

6

7 Chapter I General Description 1.1 Description V1691 series receiver/drivers are designed as the remote control devices for operation of motorized camera pan/tilt units and motorized camera lens units. Since the camera sites are usually far away from the operators viewing location, these receiver/drivers are designed to control the site cameras as well as lights, doors, etc. V1691 series receiver/drivers obtain control instructions via the common code line, which is originally from the CPU of matrix switching system, the system input bays, intervening code distribution units, or other units capable of generating the control codes. To enable it to identify the corresponding control signals, each receiver/driver must be set during the installation to match up with the camera ID associated. 1.3 Features Single channel receiver/driver Flexible Pan/Tilt and Lens Control 24VAC and 14VDC output AUTOPAN function Waterproof (for outdoor) Multiple presets, ability to call up preset scenarios stored in non-volatile memory Local test feature to verify the connection between the receiver, pan/tilt and the lens Receives Manchester and RS485 control code (INFINOVA, SAMSUNG, PELCO-P/D) All V1691 series receiver/drivers allow control of either standard rotation or 360-degree rotation Pan/Tilt units. 1.2 Models V1691 V1691X V A V1691E V1691EX V1691E-24A For indoor application. Manchester & RS485 receiver/driver, 120VAC/60Hz input, 14VDC/ 24VAC output for camera power, pan/tilt, lens and auxiliaries operation For indoor application. Manchester & RS485 receiver/driver, 230VAC/50Hz input, 14VDC/ 24VAC output for camera power and pan/tilt operation For indoor application. Manchester & RS485 receiver/driver, 24VAC input, 14VDC/24VAC output for camera power, pan/tilt, lens and auxiliaries operation For outdoor application. Manchester & RS485 receiver/driver, 120VAC, 14VDC/24VAC output for camera power, pan/tilt, lens and auxiliaries operation, sealed, waterproof For outdoor application. Manchester & RS485 receiver/driver, 230VAC, 14VDC/24VAC output for camera power, pan/tilt, lens and auxiliaries operation, sealed, waterproof For outdoor application. Manchester & RS485 receiver/driver, 24VAC input, 14VDC/24VAC output for camera power, pan/tilt, lens and auxiliaries operation, sealed, waterproof 1

8 Chapter II Installation This installation should be made by a qualified service person and should conform to all local codes. Note: Take V1691 as an example to show unit installation in this chapter. Unless specially noted, the descriptions illustrated for V1691 apply to all V1691 series receiver/drivers. 2.1 Mounting V1691 receiver/driver is used both indoor and outdoor, and it may be surface mounted in any orientation. To minimize voltage drop in the wiring, mount the receiver/driver near the cameras to be controlled. The dimensions of the receiver/driver are: W305mm H83mm D202mm (outdoor) or W290mm H95mm D185mm (indoor), without the mounting ears. Select the suitable nuts when making surface mount. For wood studs mount, use lag bolts (with a drilled pilot hole) or wood screws, which penetrate the wood for at least one inch. For concrete surface mount, use lead or plastic anchor expansion bolts with a minimum pull-out rating of 10 pounds. For steel surface mount, drill four bolt clearance holes and use bolts with lockwashers and nuts. For drywall (gypsum) wallboard mount, use toggle bolts. Drywall thickness must be at least 0.38-inch. 218mm (Outdoor) 198mm (Indoor) 200mm (Outdoor) 208mm (Indoor) R5.9mm (Outdoor) R5.25mm (Indoor) R3.9mm (Outdoor) R3.5mm (Indoor) Chapter III System Connections and Setup 3.1 System Connections Note: Take V1691 as an example to show system connections and setup in this chapter. Unless specially noted, the descriptions illustrated for V1691 apply to all V1691 series receiver/drivers Code Source to V1691 Series receiver/drivers V1691 control line connector (J202) is a 3-position terminal, labeled B R+,, and on the side panel of the unit, and a mating 3-position screw-terminal plug is supplied. Note: The code source could be INFINOVA series matrix switching system, V2116 system keyboard or V2411 code distributor. Wiring: Use 18 AWG, shielded, 2-wire cable, Belden 8760 or equivalent (for plenum, Belden 88760). The maximum connection distance is 5000 ft. Insert the appropriate signal wires into the slots of the mating connector and tighten the hold down screws. When all wires have been connected, insert the mating connector into the code connectors on V Check the power supply cable to make sure power is off; 2. Insert and screw down the Black Code wire into the screw terminal marked B R+; 3. Insert and screw down the White Code wire into the screw terminal marked ; 4. Insert and screw down the Shield wire into the screw terminal marked. V1691 receiver/driver is designed for a Star connection to a code distribution unit. A 120-ohm terminating resistor is installed on the Receiver code input line (See figure 3-1, 3-2). Receiver B R Ohm Terminator Receiver B R Ohm Terminator Other Receivers Figure 2-1 Mounting Size Receiver B R Ohm Terminator W B S W B S W B S Code Distribution Unit B W S B W S Code Source Figure 3-1. Manchester Star Connection 2

9 Receiver Ohm Terminator Receiver Ohm Terminator Receiver B R+ B R+ B R Ohm Terminator T- T+ G T- T+ G T- T+ G Code Distribution Unit T+ T- G T+ T- G Code Source Figure 3-2. RS485 Star Connection Other Receivers When V1691 is used in a Daisy Chain configuration, remove the 120-ohm terminating resistor from all but the last Receiver (see Figure 3-3, 3-4). Remove Manchester Jumper J200, and RS485 Jumper J201 on the PCB to eliminate the terminal resistor. The green LED labeled CODE on V1691 receiver/driver illuminates when the unit is receiving valid control code. The LED turns off immediately after the control code disappears Ohm Terminator Receiver Receiver Receiver B R+ B R+ B R Pan/Tilt and Lens Connections The connection to a Pan/Tilt unit and a motorized camera lens is with a 12-pin connector. This connector, labeled J300, J301 is located on the main PCB (see Appendix II). A mating 12-position screw-terminal connector plug is provided. When wiring the connector, insert each wire carefully with approximately 0.25 inch of insulation removed. Screw down the clamping screw on each pin of the connector. Pan/Tilt Wiring: 1. Check the power supply cable to make sure the power is off. 2. Locate the Pan/Tilt and Lens connector on the side of the receiver/driver near the power cord. 3. Insert the Pan Right wire of the Pan/Tilt unit into the pin location for Pan Right. 4. Insert the Pan Left wire of the Pan/Tilt unit into the pin location for Pan Left. 5. Insert the Tilt Up wire of the Pan/Tilt unit into the pin location for Tilt Up. 6. Insert the Tilt Down wire of the Pan/Tilt unit into the pin location for Tilt Down. 7. Insert the Pan/Tilt Common of the Pan/Tilt unit into the pin location for Pan/Tilt Common. Lens Wiring: 1. Check the power supply cable to make sure the power is off. 2. Locate the Pan/Tilt and Lens connector on the side of the receiver/driver near the power cord. 3. Insert the Iris wire of the Lens unit into the pin location for Iris. 4. Insert the Focus wire of the Lens unit into the pin location for Focus. 5. Insert the Zoom wire of the Lens unit into the pin location for Zoom. 6. Insert the Lens Common wire of the Lens unit into the pin location for Lens Common. Note: Do Not Connect the Lens Common to the Pan/Tilt Common. T- T+ G Code Source Figure 3-3. Manchester Daisy-chain Connection Camera Power Connections V1691 receiver/driver provides 24VAC and 14VDC power source for camera (See Appendix II). Please refer to section for details Ohm Terminator Receiver Receiver Receiver B R+ B R+ B R Setup DIP Switch SW200 DIP Switch SW200 is used to set the local camera ID, ranging from 1 to 255. Besides, it could be used for system testing. For details, please refer to the appendixⅠ. W B S Code Source Note: After the address is changed, it must be re-powered to control the receiver. Figure 3-4. RS485 Daisy-chain Connection 3

10 3.2.2 DIP Switch SW201 Table 3-1. Meaning indicates the initiate state. 1, 2, 3----Set the baud rate; 4, 5, 6----Set the communication protocol; 7---Set the preset; 8---Select the system testing mode or normal working mode. Table 3-2. Set the baud rate (1=ON, 0=OFF) DIP Switch Baud Rate Table 3-3. Set the communication protocol (1=ON,0=OFF) DIP Switch Communication Protocol MANCHESTER PELCO-D PELCO-P SAMSUNG INFINOVA Note: When selecting Manchester communication protocol set OFF for all positions of the DIP switch; When selecting PELCO-D communication protocol, the baud rate could be fixedly 2400bps. Table3-4. Set the Preset (1=ON,0=OFF) DIP Switch Preset ON/OFF 7 ON 1 OFF 0 Table3-5. Set the system mode (1=ON,0=OFF) DIP Switch System Mode 8 System Testing Mode 1 System Working Mode 0 Testing Mode Control V1691 receiver without the cable connection. Follow the steps above to use DIP Switch SW200 to set the testing mode. For details on the switch position on the PCB, please refer to the appendix Ⅱ Lens Voltage Adjustment V1691 is adjustable for a range of camera Lens servo voltages. The lens output voltage can be adjusted through the selection switch (R114) on V1691 PCB. The voltage range is from 6V to 14V, and the default voltage is 10V Jumper Setting Note: The PCB edge is in the left of the jumper switch. Terminator Setting Terminator jumper: Manchester ---J200; RS J203 J200 J203 Communication Mode Setting V1691 receiver/driver could select Manchester or RS485 through the internal jumpers J204 and J201 on the PCB. The jumper is set as below: PCB Edge PCB Edge Figure 3-5 Manchester Mode Figure 3-6 RS-485 Mode J204 J201 J204 J201 AUX Mode Setting: The AUX2 can set the Auto pan through jumper J309.The jumper is set as below: J309 A 24VAC output always exists between AUX2A and VACCOM. There is 24VAC output between AUX2B and VACCOM when the receiver/driver receives AUX2 ON command; and the 24VAC output between AUX2B and VACCOM will disappear when the receiver/driver receives AUX2 OFF command. In the case that the AUX2 is set to AUTO PAN, the pan/tilt device will start AUTOPAN action when the receiver/driver receives AUX2 ON command; and the pan/tilt device will stop AUTOPAN action when the receiver/driver receives AUX2 OFF command. Note: The factory default mode is AUTO PAN mode. 4

11 RS-485 Connection Method Manchester Connection Method Matrix Switcher Receiver Matrix Switcher Receiver TX- W TX+ B R+ B B R+ GND S Figure 3-7. RS-485 Connection Method Figure 3-8. Manchester Connection Method Presets Protocol Address Baud rate (bps) Presets V2116 V2116+V2011 V2116 V2116+V2011 V2116 V2116+V2011 Manchester / / Pelco P Pelco D Infinova Samsung

12 Chapter IV Operation 4.1 Preparation There are many switches that must be set up before operation of this product, as described in System Connection and Setup section. An incorrect setting may result in damage to this unit and any other device connected to it. Make sure that the unit is power off before finishing installation and check all wiring and cabling before applying power. Appendix I Camera Site ID DIP Switch Settings 1=ON, 0=OFF 4.2 Powering On V1691 series receiver/drivers provides a pendant cord for use with a standard electrical outlet. For the power source required, please refer to Section 1.2 Models. The Receiver circuitry includes two transformers: one for the on-board circuitry, which has a non-replaceable thermal fuse; and the second for the Pan/Tilt and Auxiliary output, which has a replaceable fuse. If the replaceable fuse should blow, check all external wiring. Repeated fuse blowing indicates incorrect wiring, defective Pan/Tilt units, or excessive Auxiliary loads. The red LED labeled POWER on the V1691 panel illuminates when the unit is powered on. If the LED does not illuminate, it indicates that there might be loose power connection or something wrong with the receiver. The green LED labeled CODE on the V1691 panel illuminates when the unit is receiving valid code. The LED turns off immediately after the code disappears. If this LED does not illuminate, there might be something wrong with the code transmission, poor or loose connection, improper termination, or something wrong with the receiver. Power Reset When any changes are made to the Pan/Tilt Preposition wiring or Preset switches, V1691 series receiver/drivers must be power-reset. To power-reset the receiver/drivers, unplug the units from the power source, wait for 5 seconds, then plug them back into the power source. 4.3 Pan/Tilt Lens Control V1691 series receiver/drivers provide 24 VAC or 14VDC power supply for the camera. The voltage for lens control is from 6VDC to 14VDC, and the default voltage is 10V. One 12-pin connector on the side of the unit contains all the connections required for control of the Pan/Tilt and lens. 6

13 1=ON, 0=OFF 7

14 1=ON, 0=OFF The CAM address ranges from 1 to 255 for PELCO-P/D, from 1 to 128 for Infinova protocol, from 1 to 254 for SAMSUNG, and from 1 to 64 for Manchester protocol. 8

15 Appendix II System Testing Function SW200 DIP Switch Up Down Left Right Left-up Left-down Right-up Right-down Focus FAR NEAR Iris CLOSE OPEN Zoom WIDE TELE AUX ON 1 OFF 0 Note: indicates 0 or 1. 9

16 Appendix III Specifications Operational Controllable Camera Sites: One Controllable Functions: Pan, Tilt, Zoom, Focus, Iris Pan/Tilt Drive: 24 VAC (2.0 A per drive motor) Lens Drive: ±6 to ±14VDC (adjustable), 50 ma Address Range: Control Code: Manchester, RS485(SAMSUNG, PELCO-P/D,INFINOVA) Code Impedance: Balanced, 120 Ω, shielded twisted pair Local Control: All functions Electrical Supply Voltage: Power Output: Power Requirements: (With camera load): 120VAC/60Hz; 230VAC/50Hz, 24VAC 24VAC, 14VDC 5W 14W Mechanical Dimensions (W H D) V1691: 7.3" 3.7" 11.4" (185 mm 95 mm 290 mm) V1691E: 12.0" " (305 mm 83 mm 202 mm) Package Size (W H D) V1691: 10.0" 6.3" 3.0" (254 mm 159 mm 330 mm) V1691E: 15.0" 6.5" 11.3" (381 mm 165 mm 286 mm) Unit Weight V1691: 4.4 lbs. (2 kg) V1691E: 6.6 lbs. (3 kg) Shipping Weight V1691: 7.4 lbs. (3.35 kg) V1691E: 9.6 lbs. (4.35 kg) Enclosure: Mounting: Environmental Operating Environment: Operating Temperature: Operating Temperature: Relative Humidity: Aluminum (V1691E) / Plastic (V1691) Surface Mount Indoor/Outdoor 32 F ~140 F (0 C ~ 60 C) (Indoor) -22 F ~140 F (-30 C ~ 60 C) (Outdoor) 0~90%RH (non-condensing) 10

17 Appendix IV Typical System Connections 1. Connect V2011 to V1691 CAMERAS ALARMS RELAYS MONITORS NONCCM NONCCM RS232 PORTS ETHERNET MANCHESTER CODE RS485 PORT T+ T- GND B W S B W S B W S B W S V2011 J202 B R+ V1691 Apply to all V1691 series receiver/drivers. 11

18 2. Connect V2015 to V1691 VIDEO INPUTS ALARMS CODE B W S B W S B W S B W S RELAYS RS485 T+ T- GND NO NC CM NO NC CM PROG MON DATA LINE RS232 PORTS ETHERNET POWER VIDEO OUTPUTS V2015 J202 B R+ V1691 Apply to all V1691 series receiver/drivers. 12

19 RISK OF ELECTRIC SHOCK DO NOT OPEN 3. Connect V2020 to V and V PORT IN DATA LINE OUT IN EXT SYNC OUT CAUTION OUT POWER 16 PGM V2020 DATA LINE T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G IN OUT T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G T+ T- G V J202 B R+ V1691 Apply to all V1691 series receiver/drivers. 13

20 4. Connect V2116 Keyboard to V1691 J202 B R+ V1691 POWER RS485 MANCHESTER ETHERNET R Infinova SYSTEM KEYBOARD RS232 ETHERNET T+ T- G B W S Communication ports on V2116 rear panel LAST LOCK ACK NEXT RUN HOLD OFF ARM SALVO PATRN SHOT PROG CAM 0 MON AUXILIARY P P A A G OFF ON G E E IRIS P P A A G CLOSE OPEN G E E FOCUS NEAR FAR CONTROL E E N X T USER SITE I E T R UP L R ZOOM OPERATE PROGRAM F1 CLEAR F2 WIDE TELE DOWN MENU V2116 Apply to all V1691 series receiver/drivers. 14

21 5. Connect Pan/Tilt & Lens to V1691 ZOOMPOT FOCUSPOT TILTPOT PANPOT -REF +REF GND 12VDC LENSCOM ZOOM FOCUS IRIS Camera AUX2 A AUX2 B AUX1 N/O AUX1 N/C AUX1 COM LEFT RIGHT VACCOM UP DOWN VACCOM 24VAC Pan/Tilt J300 J301 Apply to all V1691 series receiver/drivers. 6. Connect the camera & Pan/Tilt to V1691(with presets) Pan/Tilt ZOOMPOT FOCUSPOT TILTPOT PANPOT -REF +REF GND 12VDC LENSCOM ZOOM FOCUS IRIS Camera AUX2 A AUX2 B AUX1 N/O AUX1 N/C AUX1 COM LEFT RIGHT VACCOM UP DOWN VACCOM 24VAC J300 J301 Note: For detailed information of the camera wires, please refer to the relevant users manual of the camera in use. Apply to all V1691 series receiver/drivers. 15

22 Infinova 51 Stouts Lane, Monmouth Junction, NJ 08852, U.S.A. Tel: (USA only) Fax: V