READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING
|
|
- Debra Lawson
- 5 years ago
- Views:
Transcription
1 OPERATING INSTRUCTIONS 350B Back Buddy II READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING S. 40th Street Phoenix, AZ Fax March 20, 2017 MADE IN USA
2 GENERAL INFORMATION General: Overview: Remove contents from box, review parts and see page 3 for assembly. Read and follow instructions for optimum use. The 350B Back Buddy II is designed to reduce fatigue and injury during brake and bearing seal maintenance on vehicles. Lift capacity is 350 lbs. 48 tall x 27 wide and 27 1/2 deep. Freestanding it weighs just over 100 lbs and is very easy to handle and maneuver. WARNING! WEAR SAFETY GLASSES Caution should be used when dealing with heavy parts and equipment. Steel toe shoes are also recommended. Primary Features Fig. 1 Shown holding Hub Handle Handle Lock Angle Adjustmen t Knob Ratchet / Lift Handle Mounting Adapter & Lock Pin Part Pan Swivel Caster Tool Box Tire & Cotter Pin The 350B Back Buddy II can handle all hub and drum assemblies with the universal receiver and adapter sets. With a simple change of adapters users of the Back Buddy II can change from an inboard hub/drum lifting device to an outboard drum or spoke lifting device in seconds. Changing adapters is as easy as pulling the knob of the spring loaded lock/locking pin, removing the existing adapter and replace it with another adapter. Page 2
3 INSTRUCTIONS Match A this end Angle Adjustment Knob Main Frame Handle Lock Bar Handle Lock Pin Fig. 2 Insert Hinge Pin TO ASSEMBLE: Fig. 2 above shows a Back Buddy II with a handle nearly installed. The inset at top right indicates where to match A for proper assembly. Line up the handle and align the locking tabs. The handle locking tabs go on the inside of the main frame tabs. You may want to temporarily fasten these together using the handle lock pin. Line up the hinge halves and insert hinge pin. Prior to shipping each Back Buddy II unit has been fully assembled. It may be necessary to gently tap the hinge pin into place. DO NOT BEND IT. HOW TO USE: Roll the Back Buddy II up near a wheel to remove a hub. Select an adapter and fasten it into position ( See Fig. 3 and 4 on page 4.) To align the Back Buddy II to the hub turn the angle adjust knob. (Fig. 2 above) in or out. Bolt or fasten unit to hub. Page 3
4 INSTRUCTIONS Fig. 3 As shown in Fig. 3, insert the adapter in the receiver with the grooves on the adapter facing away from you. Pull the lock/locking pin, slide in the right or left adapter and allow the pin to fit into the hole in the adapter. Make sure the pin locks the adapter in the receiver. Locating Pin Below are two standard adapters sent with each Back Buddy II unit. The MKA2 and MKA3. MKA2/2H - TSI # stud inboard hubs. Studs 335 mm on center. MKA3/3HD - TSI # stud outboard hubs. Studs on center, 3/4 hub back plate thickness. In Fig. 4 shows an operator has fastened the Back Buddy II to a hub. The arrows point to the lift ratchet and the angle adjustment knob. Use both to align the unit to your vehicle hub. Fig. 4 Fig. 5 Page 4Page 3
5 INSTRUCTIONS WARNING! KEEP FEET AND HANDS CLEAR WHEN TIPPING UNIT Ensure ratchet handle is stowed before laying it down on its back. Tip the Back Buddy II back to service brake drum. The pull handles in back are angled to rest the unit on its back without crushing or pinching your fingers as you use the upper hand to pivot it with. See Fig. 6 Tip it foward to service the hub as shown in Fig.7 Fig. 6 Fig. 7 Page 5
6 MAINTENANCE The maintenance recommendations on this product are on an as needed basis. Under normal use it is advisable to periodically check for loose bolts, knobs the ratchet chain and rollers and tighten them when necessary. Fig. 8 Fig. 9 Apply grease on square tube where shown in Fig. 8. To adjust ratchet chain loosen bolts (Fig.9) lift on ratchet and re-tighten the bolts. Tighten round knobs if loose. Fig. 10 Snug all other bolts as needed, also shown in Fig. 11. Fig. 11 Page 6
7 ADAPTER OPTIONS TSI#6069 MKA2/2HD TSI #6073 MKA3/3HD TSI #6071 MKA4 S TSI #6074 MKA5 mm on center. TSI #6075 MKA6 S TSI #6076 MKA7 TSI #6077 MKA8 TSI #6067 MKHMV Page 7
8 350B BACK BUDDY II S. 40th Street Phoenix, AZ Fax MADE IN USA
Further Information can be found at
Below is a step by step guide to assembling the Hurricane-Rig. Remember that this is a precision optical instrument. Excessive force can bend critical parts. If treated well it should give many years of
More information1 AM-167/202/242/282/322 Parts Manual. Table Of Contents
AM-167/202/242/282/322 Parts Manual Table Of Contents Mower Beam with Bearings...2 Mower Beam with Bearings...4 Cutting Discs...6 Main Gearbox...8 V-Belt Pulley...10 Headstock...12 Carrier Beam...14 V-Belt
More informationEVOLVE1-M MONITOR ARM
EVOLVE1-M MONITOR ARM EVOLVE1-M Rev A 2/17 Model EVOLVE1-M-SLV Model EVOLVE1-M-BLK Model EVOLVE1-M-WHT ASSEMBLY AND ADJUSTMENT EVOLVE1-M MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before
More informationStainless Steel Hatch Fasteners Page
Izerwaren numbers Stainless Steel Hatch Fasteners Page -4-3-0-0 hatch fasteners, flush type with separate key sea water resistant - leak proof finish: rolled Installation: Drill hole: 22.5 mm Ø / 7/8 Back
More informationM-2300-ZX Focus SVT Brake Conversion Kit INSTRUCTION SHEET
Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: This kit is designed
More informationTABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION
S6 USER S MANUAL TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION SECTION 4 SLIDE CONFIGURATION ACCESSORIES SECTION 5 RACK MOUNT
More informationDUAL-ARM MONITOR MOUNT For in. ( cm) desktop computer monitors
LeviTouch DM-502 DUAL-ARM MONITOR MOUNT For 15 27 in. (38.1 68.6 cm) desktop computer monitors User Manual Thank you for choosing Gabor. The Gabor Dual-Arm Desktop Mount can securely support two monitors
More informationAssembly and Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required
More informationC-pan arm USERS INSTRUCTIONS
C-pan arm USERS INSTRUCTIONS Designed 1 of 12 and made in Denmark Thanks for purchasing a 9.Solutions product. With great passion, we design our products to be as versatile as possible. We hope that our
More informationInstallation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit
Installation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter on Arm (page 2). 2.
More informationATV Single Row Disc Harrow OWNER S MANUAL
ATV Single Row Disc Harrow OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationRedexim-Charterhouse Verti-Core 1300/ 1700/ 2100 pag 01 code 0202
Redexim-Charterhouse Verti-Core 1300/ 1700/ 2100 pag 01 code 0202 Part# 1300 Part# 1700 Part# 2100 DESCRIPTION REMARKS QUA 1 844.060.060 Same Same Winged nut - M6 10 2 830.060.060 Same Same Self lock nut
More informationRear-Engine Riders Parts Manual
Rear-Engine Riders Parts Manual Models 06 - RM0 0 - RM0 0 - RM00 0 - RM 06 - RM0 06 - RM0 0 - RM 0 - RM 0 - RM0 0600B /0 Supercedes 0600,A Printed in USA THE MANUAL Before you operate your unit, carefully
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationDS5/DS10/DS20 Fluid Head Operator s Manual. #180 DS5 Fluid Head #182 DS10 Fluid Head #184 DS20 Fluid Head
DS5/DS10/DS20 Fluid Head Operator s Manual #180 DS5 Fluid Head #182 DS10 Fluid Head #184 DS20 Fluid Head Features and Controls 1/4 and pin carriage Sliding camera plate Slide lock Tilt lock Tilt drag Pan
More informationskyline 70 Fluid Head OPERATOR S MANUAL #1050 Skyline 70 Fluid Head
skyline 70 Fluid Head OPERATOR S MANUAL #1050 Skyline 70 Fluid Head Features and Controls Sliding Plate Lock Sliding Plate Pan Handle Clamp Tilt Lock Pan Handle Safety Lock Knob Pan Lock Threaded Stud
More informationJuly Manual 10-slide disk outdoor viewer
Ing. J. de Wijs. Populierstraat 44, 4131 AR Vianen, the Netherlands Tel/Fax. +31 (0)347-372242 e-mail: info@dewijs-3d.com Website: www.dewijs-3d.com Design and production of stereoscopic instruments. July
More informationUniversal Tristop Cylinder for Cam Brakes
Tristop for Cam Brakes 3rd Edition This publication is not subject to any update service. New versions are available in INFORM at www.wabco-auto.com Copyright WABCO 2006 Vehicle Control Systems An American
More informationProduct Overview. Features
APCF1 Model Tripod Product Overview The Ravelli APCF1 is a Professional Quality Carbon Fiber Tripod providing a solid base for high-end photographic equipment. This model is a mix of carbon fiber and magnesium
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationASSEMBLY AND ADJUSTMENT
EDGE-WALL MONITOR ARM EDGE-WALL Rev A 2/17 Model EDGE-WALL-SLV ASSEMBLY AND ADJUSTMENT EDGE-WALL MONITOR ARM PLEASE REVIEW these instructions before beginning the installation. Check that all parts and
More informationVZ-SnapCrane-12 Professional Modular Camera Crane Instruction Manuall
VZ-SnapCrane-12 Professional Modular Camera Crane Instruction Manuall WEIGHTS NOT INCLUDED STANDARD 1 -HOLE BARBELL WEIGHTS ARE AVAILABLE AT MOST SPORTING GOODS STORES For a video tutorial SnapCrane Build,
More informationNAV-1 Lens Support. NAV-2 Lens Support BEFORE YOU BEGIN
INSTALLATION Lens Support INSTRUCTIONS The Lens Support is compatible with any RPA projector mount. The readily adapts to the following ScreenStar Conversion Lens from Navitar: SSW08 and SST120. LENS SUPPORT
More information580 RS, 580 RSE, 580 RSW, 600 C. Part s Manual A 3/00 Printed in USA
580 RS, 580 RSE, 580 RSW, 600 C Part s Manual 606 00 0 7A /00 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied with the unit. The contents will provide
More informationPortable Staging User Guide
Portable Staging User Guide Components: ExpressDeck was designed for quick and easy assembly: set up is a snap, even if you have no experience! So let s take a moment to meet the components of your new
More informationParts and Service Manual IMCO
XXTREME ADVANTAGE Gimbal Parts and Service Manual IMCO 510 East Arrow Highway San Dimas, CA 91773 (800) 899-8058 (909) 592-6162 Fax (909) 592-6052 www.imcomarine.com email info@imcomarine.com TABLE OF
More informationVZ-SnapCrane-16 Professional Modular Camera Crane Instruction Manuall
VZ-SnapCrane-16 Professional Modular Camera Crane Instruction Manuall WEIGHTS NOT INCLUDED STANDARD 1 -HOLE BARBELL WEIGHTS ARE AVAILABLE AT MOST SPORTING GOODS STORES For a video tutorial SnapCrane Build,
More informationDesign and Manufacture of Video Pipeline Inspection Systems A Full Service Company
Design and Manufacture of Video Pipeline Inspection Systems A Full Service Company www.rstechserv.com Omni Star LED Pan and Tilt Zoom Color Camera Modell 10-1660 INSTALLATION MANUAL Made in USA IMPORTANT
More informationRedexim-Charterhouse Verti-Drain 7316 pag 01 code 0401
Redexim-Charterhouse Verti-Drain 7316 pag 01 code 0401 1 4191100 Winged nut 10 2 4100800 Self lock nut M6 10 3 2282183 Bottom PTO protection cover 1 4 4001030 Bolt M6 x 16 10 5 2281782 Top PTO protection
More informationStealthyPro Instructions
StealthyPro Instructions 3-point Shooter Mode / Handheld Mode / Monopod Mode Place the black piece between the handle and the silver ring (as pictured). Stabilizer Mode In stabilizer mode, thread the handle
More informationCHAPTER 5 UNIT MAINTENANCE INSTRUCTIONS
FPU SYSTEMS OPERATION MANUAL (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) STANDARD AND SPECIALIZED FPU MODULES BOH FPU Field Pack-up Units CHAPTER 5 UNIT MAINTENANCE INSTRUCTIONS BOH-PM-0-5 06 BOH Environmental
More informationFlat Panel Static Wall Mount MSP-SS (GSM-210)
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount (GSM-2) The static wall mount fits most 23 to 30 displays. The mount was designed to adapt to the VESA 75mm/0mm, 0mm/0mm, and 200mm/0mm compliant
More informationTitan Media Cart. Installation and Operation Manual
Titan Media Cart Installation and Operation Manual Table of Contents INTRODUCTION SERVICE AND SUPPORT... 1 PRODUCT RETURNS... 1 UNPACKING... 1 TITAN SINGLE MEDIA CART... 2 TITAN DUAL MEDIA CART... 2 BEFORE
More informationG12/G12x USER S MANUAL
G12/G12x USER S MANUAL TABLE OF CONTENTS SECTION 1 SLIDE CONFIGURATION SECTION 2 SLIDE CONFIGURATION ACCESSORIES SECTION 3 TABLETOP CONFIGURATION SECTION 4 TABLETOP CONFIGURATION ACCESSORIES SECTION 5
More informationCycles Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Recumbent Upright Cycles Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 4 Obtaining Service... 4 Unpacking the
More informationDescription: Detailed procedure on removing old bushing and installing new Brake Bushing Replacement Kit 10447
Procedure: BRAKE BUSHING REPLACEMENT PROCEDURE Product: Document #: Rev: Page: MODEL 7000, 7000A, & 8000 GYRO 078 1 1 of 14 Description: Detailed procedure on removing old bushing and installing new Brake
More informationMBX INSTRUCTION MANUAL. Please read this manual carefully before using the MBX! Mid-range studio stand
MBX Mid-range studio stand INSTRUCTION MANUAL EN Please read this manual carefully before using the MBX! CAMBO Thank you for purchasing a Cambo product. This new classed Mid-range studio stand will suit
More informationA-MOD DESKTOP OWNER S MANUAL
A-MOD DESKTOP OWNER S MANUAL GOJOTTO.COM 877-55-6886 IMPORTANT NOTICE: Please take a few minutes to read through this Owner s Manual before using the product to ensure that your A-MOD Desktop will be operated
More informationJLTX Lever and Joystick Replacement Instructions
JLTX Lever and Joystick Replacement Instructions WARNING THE INCORRECT INSTALLATION OF A LEVER OR JOYSTICK CAN CAUSE AN EQUIPMENT MALFUNCTION FAILURE TO FOLLOW THIS PROCEDURE CAREFULLY COULD RESULT IN
More informationAssembly and Setup Manual
M-12 Series Copyboard / C-12 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-12 series Copyboard and C-12 series Captureboard. (The copyboard and/or
More informationV40 Videoboom MAIN OPERATING INSTRUCTIONS INDEX 5. SPECIFICATIONS V40 1. INTRODUCTION 2. LIST OF FUNCTIONS AND PARTS
MAIN OPERATING INSTRUCTIONS V40 Videoboom INDEX 1. INTRODUCTION 2. LIST OF FUNCTIONS AND PARTS 3. INSTRUCTIONS V40 3.1 ASSEMBLY & SETTING UP 3.2 WEIGHT SYSTEM 3.3 MOUNTING THE VIDEO CAMERA 4. USING THE
More informationAPES-14 HD-6500 & HD-7000 Version Operator s Training Manual
APES-14 HD-6500 & HD-7000 Version Operator s Training Manual Issue A1 09/03 PDI Part # 900600 Performance Design Inc. 2350 East Braniff St. Boise Idaho 83716 This manual contains very important safety
More informationTower Company, Inc. IM1.00MVU (REV.B) 1639 Old Dixie Highway P.O. Box Vero Beach, FL USA Voice (772) Fax (772)
PAGE 1 OF 8 MOBILE VAN UNIT TRACK-CARRIAGE ASSEMBLY INSTALLATION AND TOWER SET-UP INSTRUCTIONS PAGE 2 OF 8 W A R DANGER I N G WARNING NOTICE DANGER!!! W A R DANGER I N G DO NOT CLIMB! DEATH MAY OCCUR!
More informationIBM. Rack Installation Instructions
IBM Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following:
More informationSPECIFICATION & INSTALLATION GUIDE
SPECIFICATION & INSTALLATION GUIDE FREEFRAME FP7 v3 Mobile Stand for Flat Panel Display with Motorized Raise and Lower www.gilkon.com.au email: sales@gilkon.com.au phone: (02) 99140900 fax: (02) 99140901
More informationRack Installation Instructions
Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following: v Two
More information2.4Meter Series 1252 Az/El Truss Mount
4096-356 REVISION E April 21, 2016 Assembly Manual 2.4Meter Series 1252 Az/El Truss Mount General Dynamics 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com 2.4M Series 1252
More informationFloor Standing Pedestal
2336 K052 Floor Standing Pedestal Kit Instructions Issue C Revision Record Issue Date Remarks A Feb 20021 First issue B June 2007 Added pedestal floor bolting procedure C Mar 2011 Added Universal Mounting
More informationWalk-Behind Lawn Mowers
Walk-Behind Lawn Mowers Parts Manual Models 9099 - LM1SH 9101 - LM1SWH 910 - PRO1SCH 90 - LM1SW 91 - LM1SE 951 - LM1S 9515 - LM1SE 955 - LM1SW 956 - LM1SC 957 - LM1SCHB 951 - LM1S 0500D 9/0 Supersedes
More informationMoving-Minds.com Treadmill Desk Operation
LifeSpan Treadmill Desk - Owner s Manual Models DT-5/DT-7 Desk Assembly DT-5 Desk........................................................................................ Assembly Instructions..........................................................................
More informationTreadmill Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Treadmill Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 Before You Begin... 4 Obtaining Service... 4 Unpacking the Equipment... 4 Important
More informationATV Single Gang Disc Harrow OWNER S MANUAL
ATV Single Gang Disc Harrow OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationFLEXBOX. Installation Guide
FLEXBOX Installation Guide FLEXBOX 1 Important Safety Instructions WEIGHT LIMIT MAXIMUM WEIGHT 50 LBS. THE STRUCTURE TO WHICH THE BOX IS MOUNTED (CEIL- ING, WALL, TABLE, POLE) MUST BE ABLE TO SUPPORT FIVE
More informationRaptor Series Adapters
Raptor Series Adapters 3-6 ADAPTER 6-10 ADAPTER For Air Powered Lug and Torque Chucks Adapter Sizes 3 5 3 6 3 6.75 3 150mm 3 7.415 3 8 6 8 6 10 6 12 TABLE OF CONTENTS Caution... 3 Tidland Customer Service...
More informationPrime Railway Services Radial Door - Order Form
Radial Door - Order Form Prime Part # 1130 Customer/Location: Tel: Fax: Quantity: Door ID#: Door Type: Tri Bi Door Location: BR BL AR AL BL Doors Only: Sliding Door or Pan Exterior Door Colour Red Yellow
More informationJIB EPT USER MANUAL. Please read this manual carefully before using the Alphatron JIB ETP unit! JIB & MOTORISED PAN AND TILT UNIT
JIB EPT JIB & MOTORISED PAN AND TILT UNIT USER MANUAL EN Please read this manual carefully before using the Alphatron JIB ETP unit! Thank you for purchasing a Alphatron product The EPT head is developed
More informationHANDLEBAR AND CONTROLS
HANDLEBAR AND CONTROLS Model 80 R, 80 RS, 80 RSE, 80 RSW, 80 BBC, 00 C 80 BBC 80 R, 80 RS, 80 RSE, 80 RSW, 00 C 8 8 0 0 8 0 8 0 0 8 PM00 0 00 00 0 Engine Bail Weldment(80 R, 80 RS, 80 RSE, 80 RSW, 00 C)
More informationFigure 4-29 Removing the CPU compartment cover
4 Replacement Procedures 4.9 CPU 4 4.9 CPU Removing the CPU To remove the CPU, follow the steps below. 1. Turn the computer upside down and remove two M2.5 4 security screws securing the CPU compartment
More informationPage 3. Page Page 4. Page 5. Page 6. Page 2. Page 7
Parts manual Verti-Drain 416 Page 01 Code 1640 TM Page 3 Page -10 Page 4 Page Page 6 Page 2 Page Page 8 Page : PTO Page : Tines, adapters and turf hold down kits Page 13: Optional core collector Page
More information1/2
http://partsradar.arinet.com/scripts/empartisapi.dll?mf&app=ariens&session=27f5776d-d5a8-4417-865b-d472735c5bb5&cat=2&assem=4658&imgma 1/2 Ref # Par t # Descr iption Context Note Foot Note Min Qty UOM
More informationipod Classic Battery Replacement Replace the battery on your ipod classic. Written By: irobot ifixit CC BY-NC-SA
ipod Classic Battery Replacement Replace the battery on your ipod classic. Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Battery not lasting long? Swap it out. TOOLS: 1.5"
More informationQuick Installation Guide
Full Motion Single Monitor Arm, Pole Mount Quick Installation Guide Please Review the entire Quick Installation Guide prior to installation. If you have any questions regarding the compatibility of this
More informationBolt 1/4"x 2" Grade 2 Zinc , , , Nyloc Hex Nut 5/16" , , ,
Color Logo use on white background only Parts Details LH00, LH000, LH00, LH000, Track Sections & Engines Updated: //0 TIE DOWN ENGINEERING Villanova Drive SW Atlanta, GA 0 www.tiedown.com (0) -0000 Fax
More informationDrawer Safe. Black Case with Gray velvet interior. 18 1/4" wide x 6" Tall x 15 3/4" Deep. Part Number
Drawer Safe Comes with additional keys and auxiliary power jack for emergency opening. Key Pad Drawer Safe Complete Drawer Safe - strong steel case and drawer. Extremely well made quality safe ready for
More informationRL-H80 PARTS LIST # K
RL-H80 PARTS LIST # 102837K USE THIS PARTS LIST FOR: Hoist Serial Number: 2733 to For older hoists use the following: Parts List No. 102837G for Serial Number 2485 to 2732 IF YOUR HOIST DOES NOT FALL WITHIN
More informationA-dec 584 Monitor Mount on a Central Cabinet
Installation Guide A-dec 584 Monitor Mount on a Central Cabinet Before You Begin This procedure applies to the A-dec Inspire TM 592 Central Console and the standard and tall Preference cabinet central
More informationDirectCommand Installation 5 Channel Spreader Control Module Technology
DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100582 1 Cable Installation
More informationHP STD 33" Cut (S/N ) Page 1 of 15 Drive Assembly
34356 8HP STD 33" Cut (S/N 343561100101-343561199999) Page 1 of 15 Drive Assembly 34356 8HP STD 33" Cut (S/N 343561100101-343561199999) Page 2 of 15 Drive Assembly 1 1 Engine, 8 HP, Recoil Start Order
More informationQuick Start Guide Ioline StudioJet
Quick Start Guide Ioline StudioJet User Notice Trademarks Ioline StudioJet is a trademark of Ioline Corporation. HP is a trademark of the Hewlett-Packard Company. Other product names, logos, designs, titles,
More informationAVT Model Tripod.
AVT Model Tripod www.ravelliphoto.com Product Overview: The Ravelli AVT professional tripod is a high performance, fluid drag tripod that provides smooth continuous drag control and operates on both pan
More informationDI-ACRO #24 HAND SHEAR INSTRUCTION MANUAL
DI-ACRO #24 HAND SHEAR INSTRUCTION MANUAL REV. G 6/12 1 TABLE OF CONTENTS A. SAFETY INFORMATION PG. 3 B. SET UP PROCEDURE PG. 3 C. MAINTENANCE PG. 3 D. TECHNICAL DATA PG. 3 E. OPERATING PROCEDURES PG.
More informationGH-50. Gimbal Head. You re on steady ground
GH-50 Gimbal Head You re on steady ground 1 INTRODUCTION Thank You for choosing Oben! The Oben GH-50 is a gimbal-type tripod head designed to balance a lens along its vertical and horizontal axes. Ideal
More informationHOW TO INSTALL AND REMOVE SPECIAL CONNECTORS Low Fit and Lever Type Connector
B 47 HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS Low Fit and Type Connector [Case 1] (1) Push the place indicated by the arrow. (2) The lock is released and lever is lifted up. (3) Lift the lever up until
More informationUpgrading LVDS Cables Instruction Sheet
Upgrading LVDS Cables Instruction Sheet INTRODUCTION Use the following instructions to replace the LVDS cables in CP2000-M/MR projectors. The new cables are slightly longer in length and allow for better
More informationInstallation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationP F
12430 55 TH ST N OAK PARK HEIGHTS, MN 55082 P 651-342-1756 F 651-342-1293 INFO@DIACRO.COM Copyright 2014 REV. 9-MAY-2014 1 SAFETY INFORMATION PG. 3 SET-UP PROCEDURE PG. 3 MAINTENANCE PG. 3 TECHNICAL DATA
More informationOperating Instructions Wall saw WSE1217 USA
Operating Instructions Index 000 Original operating instructions 10992859 en / 25.04.2012 Congratulations! With a Hydrostress unit from TYROLIT, you have chosen a tried and tested piece of equipment which
More informationTable of Contents: TOPIC: Safe Operation: READ THIS FIRST Page: 3 Warranty 4 Specifications 4 Installation 5-7 Operating Instructions 8 Parts Diagram
INSTALLATION & OPERATIONS MANUAL FlexArm B-19 FlexArm Inc. Division of Midwest Specialties, Inc. 851 Industrial Drive Wapakoneta, Ohio 45895 419-738-8147 Book Part No 360740 12/2014 1 Table of Contents:
More informationTH ST N OAK PARK HEIGHTS, MN P F
12430 55 TH ST N OAK PARK HEIGHTS, MN 55082 P 651-342-1756 F 651-342-1293 INFO@DIACRO.COM SAFETY INFORMATION PG. 3 SET UP PROCEDURE PG. 3 MAINTENANCE PG. 3 TECHNICAL DATA PG. 3 OPERATING PROCEDURES PG.
More informationPortable Staging User Guide
Portable Staging User Guide Components: Putting together your smart stage system was designed to be simple enough for anyone to do easily. Nonetheless, let s take a moment for a little meet and greet A.)
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationipod Classic Click Wheel Replacement Written By: irobot ifixit CC BY-NC-SA Page 1 of 25
ipod Classic Click Wheel Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION The click wheel receives the feedback of your fingers and transmits it to the logic board.
More informationINSTALLATION MANUAL DATAVAULT DATAVAULT - BARE JOBSITE STORAGE SOLUTIONS
JOBSITE STORAGE SOLUTIONS ALWAYS ON THE JOB INSTALLATION MANUAL 118-01 DATAVAULT 118-02 DATAVAULT - BARE Werner Co. 724-588-2000 93 Werner Rd. 888-523-3371 toll free/ llamada gratuita Greenville, PA 16125
More informationipod Classic Headphone Jack & Hold Switch Replacement
ipod Classic Headphone Jack & Hold Switch Replacement Replace Headphone Jack & Hold Switch to fix no audio and/or no unlock Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION
More informationZebra XiII-Series Printer Quick Reference Guide
Zebra XiII-Series Printer Quick Reference Guide Contents Media and Ribbon Loading...67 Media Loading...67 Ribbon Loading...70 Operator Controls...72 Front Panel Keys...72 Front Panel Lights...72 Calibration...74
More informationINSTALLATION INSTRUCTIONS
2015 F-150 8 MyTouch factory display 360º Vision System (Kit # AVMS-3618) DUE TO THE COMPLEXITY OF THIS KIT PROFESSIONAL INSTALLATION IS REQUIRED CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING -Must
More informationPart Name/Description Part Number Quantity
Part Name/Description Part Number Quantity Direct Command Kit 4100883 1 Installation Instructions 2006336 1 Hardware Kit Large Module 2001354-1 2 Cable Installation Kit 2000901-1 1 Quick Reference Card
More informationDIGITAL Server Rackmount Installation Guide
DIGITAL Server Rackmount Installation Guide Part Number: ER-PCSRA-IA. E01 Digital Equipment Corporation December 1997 The information in this document is subject to change without notice and should not
More informationSECTION 8 - ULTRA & ULTRA-C PARTS CATALOGUE
SECTION 8 - ULTRA & ULTRA-C PARTS CATALOGUE PART # DESCRIPTION PAGE MOUNTING KITS & TANKS 903U MOUNTING KIT WITH TANK 801-802 905U MOUNTING KIT WITHOUT TANK 803-804 902U MOUNTING KIT - CRADLE, BLOCKS &
More informationCutter Option Installation Instructions
This kit includes the parts and documentation necessary to install the cutter option on the Zebra XiII, XiIII, and XiIIIPlus-Series printers. NOTE: The Cutter Option is not available for the 96XiIII. Adding
More informationUPLIFT 3-Leg Desk Instructions for. Solid Wood Desktops. (Version v4 Control Box) pictured: Solid-wood top with right hand return TABLE OF CONTENTS
UPLIFT 3-Leg Desk Instructions for Solid Wood Desktops (Version v4 Control Box) pictured: Solid-wood top with right hand return TABLE OF CONTENTS PAGE 1 Safety and Warnings 2 2 Usage 2 3 Parts List 3 4
More informationQuick Installation Guide
Full Motion Dual Monitor Arm, Pole Mount Quick Installation Guide Please Review the entire Quick Installation Guide prior to installation. If you have any questions regarding the compatibility of this
More informationInstallation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays
Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays Model: DS-VWT955-2X2 EXTENSION COLUMN (SOLD SEPARATELY) COMPATIBILITY Display width must be a minimum of 36"
More informationEpson SureColor F6070 Setup Guide
Epson SureColor F6070 Setup Guide 2 Unpacking and Assembling the Printer Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the printer
More informationLCD Series & Tablet Series Set-Up Instructions
LCD Series & Tablet Series Set-Up Instructions Parts List: Mount Arm (1) T-Nut (1) Large Camera Knob (1) Small Camera Knob (1) Mirror Knob (2) Monitor/Mirror Assembly (1) Teleprompter Parts Step #1A Remove
More informationIBM Systems. Quick start guide for IBM System p5 505 ( )
IBM Systems Quick start guide for IBM System p5 505 (9115-505) 1 Before you begin This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly unpack and set up
More informationDOOR SWEEP DOOR BOTTOM W/ SHIELD MAGNETIC DOOR SET DOOR SET WEATHERSTRIP WEATHER STRIP PUSH STYLE THRESHOLD INSERT. Page 1 WD 9110 WD 9105
C A U D I L L S U P P L Y I N C. Page 1 DOOR SWEEP DOOR BOTTOM W/ SHIELD WD 9105 WD 9110 DOOR SET WEATHERSTRIP MAGNETIC DOOR SET WD 9111 WD 9112 WEATHER STRIP PUSH STYLE THRESHOLD WD 9113 WD 9114 Bronze
More informationMicroline 420/421 & 490/491
Check the contents: 1. Printer 2. Ribbon cartridge 3. Power Cable 4. CD with drivers and online User Guide 5. Setup Guide 2 1. 2. 1. Grasp tabs (1) and open access cover (2). 2. Remove printhead shipping
More informationSAVE THESE INSTRUCTIONS
and Height Mounts Assembly, Installation and Operating Instructions Model Nos. QL, QLA, ARM250, QLM6 and QLAM6 NOTE: Check all parts for shipping damage. In case of shipping damage, DO NOT use. Contact
More information