CF /BF SERIES CAMERAS

Size: px

Start display at page:

Download "CF /BF SERIES CAMERAS"

Clare O’Brien’
5 years ago
Views:

1 Lens not Included CF /BF SERIES CAMERAS INSTRUCTION MANUAL Wide Dynamic NTSC Hi-Resolution Dual Power Wide Dynamic PAL Hi-Resolution Dual Power Wide Dynamic PAL Hi-Resolution Mains Power PAL Hi-Resolution Mains Power PAL Hi-Resolution Dual Power NTSC Hi-Resolution Dual Power PAL STD-Resolution Mains Power PAL STD-Resolution Dual Power CCIR Hi-Resolution Mains Power CCIR Hi-Resolution Dual Power EIA Hi-Resolution Dual Power CCIR STD-Resolution Dual Power CCIR STD-Resolution Main Power EIA STD-Resolution Dual Power Please Read this Instruction First!!!

2 PRODUCT SAFETY Warning Installation and servicing is only carried out by suitable qualified and experienced personnel. Mains cameras contain hazardous voltage. Do not open covers as there is a risk of injury or death by electric shock. No servicing part inside camera. Low voltage cameras must be powered from a UL listed class 2 power supply. For outdoor use, an appropriate protective housing conforming to IP65 or better must be used. Mains camera are not evaluated by UL. To PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE This camera range is designed for use in general-purpose CCVT applications and no other purpose. Only operate your camera between the temperature of -10ºC to +50ºC ( 14ºF to 122ºF ). Do not operate your camera outside its specified power supply range. Camera must only be used in clean, dry, dust-free environments unless housed in suitable protective housings to IP65 or better. ELECTROMAGNETIC COMPATIBILITY (EMC) CAUTION This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. INTENDED PURPOSE : SECURITY AND SURVEILLANCE CCTV APPLICATIONS. The product must be installed and maintained in accordance with good installation practice to enable the product to function as intended and to prevent problems. MANUFACTURER'S DECLARATION OF CONFORMANCE The manufacturer declares that the equipment supplied with this manual is compliant with the essential protection requirements of the EMC directive 89/336 and the Low Voltage Directive LVD 73/23 EEC. Conforming to the requirements of standards EN for emissions, IEC801 parts 2, 3 and 4 for immunity and EN for Electrical Equipment safety. 2

3 CONTENTS Product Safety Electromagnetic Compatibility (EMC) Manufacturer's Declaration of Conformance Contents Introduction Packing List Part Descriptions Controls and Switches Backlight compensation Sharpness on/off Gamma Selection Automatic Gain Control on/off Electronic Iris (EI) on/off Synchronizations Selection (LL / INT) Power LED on/off Line Lock Phase Adjustment Potentiometer Auto-iris lens Type Selector Switch (Video Drive or Direct DC Drive) Auto-iris lens Connector Composite Video Output BNC Connector Power Supply Mains power supply Auto-switching power supply Back Focus Adjustment Installing Fixed & manual Iris Lenses Installing Direct (or D.C.) Drive Lenses Installing Video Drive Lenses Camera Mounting Specifications 3

4 INTRODUCTION Read all of these instructions before using this camera. Retain them for reference for the lifetime of the camera. Note that not all cameras have all of the features described in this manual. Refer to the table below for the features of individual cameras. All cameras are fitted with a Direct Drive (DD) and Video Drive Auto Iris (AI) lens connector, have adjustable back focus and accept C and CS lenses. Option Wide Dynamic NTSC Dual Power Wide Dynamic PAL Dual Power Wide Dynamic PAL Mains Power PAL Hi-Res. Dual power PAL Hi-Res. Mains power PAL STD-Res. Dual power PAL STD-Res. Mains power CCIR Hi-Res. Dual power CCIR Hi-Res. Mains power NTSC Hi-Res Dual power NTSC STD-Res. Dual power EIA Hi-Res. Dual power CCIR STD-Res, Dual Power CCIR STD-Res. Main Power EIA STD-Res. Dual Power Monochrome Colour Digital Signal Process 1/3 CCD Sensor Size PAL / CCIR Scanning System NTSC / EIA Scanning System Wide Dynamic 4x Auto Frame Integration Resolution Sensitivity Lens Auto Detect Direct Drive / Video Drive Line Lock and Phase Adjustable Auto Electronics Shutter AGC Turbo Backlight Compensation ON/OFF Low light Color Killer Simple Back Focus Adjustment Power Supply Requirements: 12VDC / 24VAC SPS 100VAC ~ 230VAC Universal PACKING LIST' Camera Dust Cover Instruction Manual Mains Power cable (Available for Main Power model only) x 1pcs. x 1pcs. x 1pcs. x 1pcs. 4

5 PART DISCRIPTION AND DIMENSION Lens Mount. 8. Variable Resistor for Line Lock Phase Adjustment. 2. Back Focus Adjustment. 9. Variable Resistor for DC Lens Adjustment. 3. Back Focus Lock Screw. 10. LED for power Indication. 4. Bracket Mounting Screw Hole pin Terminal Block for Video Lens Drive Pin Lens Connector for DC Drive Lens. 12. Terminal Block for Power Input ( Dual Power ) 6. Switches for Function ON/OFF. 13. Figure 8 Power Socket for Mains Power. 7. BNC Composite Video Output. 5

CONTROLS AND SWITCHES Refer to the figure below for the various adjustments, controls and functions selectable from the 6pin DIP-switch switches.

6 CONTROLS AND SWITCHES Refer to the figure below for the various adjustments, controls and functions selectable from the 6pin DIP-switch switches. LL / INT This switch is used to select the synchronization mode of the camera. When the camera is connected to an AC supply, the Line-lock (LL) mode can be used. This locks the camera's frame rate to the mains frequency so that each camera in the system can be triggered at the same point on the supply's AC-cycle. See also Line Lock Phase Adjustment Potentiometer. The default setting is INT. AGC and TURBO The Automatic Gain Control feature can improve picture quality when the level of scene illumination is low. Select TURBO for most applications. Setting to AGC will remove noise from the image, which will also limit the sensitivity of the camera. BLC / ON Switch to ON to enable the BackLight Compensation. This feature can be used to eliminate the effect of an area of strong background lighting in a scene. If strong background lighting, such as a window, exists in a scene, the camera will try to compensate for it by reducing the overall exposure. This would mean that the areas surrounding the window would become too dark. The default setting is off (BLC). BLC ON will only function with a manual iris lens when the Electronic Iris feature is switched on. For direct drive and video drive lenses, BLC ON will still function even though the Electronic Iris feature is switched off. 6

7 Auto / Manual Lens Type Selection ( Not available for Wide Dynamic Camera ) When set to AUTO the camera will automatically detect which type of lens is attached and configure itself accordingly. Plugging a DC lens into the side connector will enable DD lens drive. Connecting a Video Iris lens to the connector on the rear will select Video Iris drive. No connection will default to AES mode. AUTO is the default setting. WD ON / Off AI / AES Mode Selection This switch operates when Auto / Man is set to MAN mode. Setting to AES forces Electronic Iris mode, compensates for excessive light levels by automatically adjusting the shutter speed of the camera. AI will force DD or Video Iris mode, depending which type of lens is connected. CK / ON Chroma Killer. When set to on and AGC is in TURBO mode, chroma information is suppressed within the image in low light. The resulting monochrome image produces a higher resolution image by removing chroma noise contained in the image. This also permits more efficient recording with a DVR. LINE LOCK PHASE ADJUSTMENT POTENTIOMETER When the camera is in line-lock mode it is possible to adjust the point on the AC cycle at which the camera triggers. This facility is provided so that cameras that are connected to different mains phases may still be synchronized. The line lock phase adjustment potentiometer allows the line lock phase trigger point to be adjusted by :1:120. Rotating the potentiometer clockwise advances the trigger point and turning it anticlockwise retards the trigger point. The factory default setting is the zero crossing point. If all cameras in a system are on the same mains phase then no line lock phase adjustment should be made-see also Synchronization Selection (LL/INT). ALC LEVEL ADJUSTMENT POTENTIOMETER The DD lens level is controlled by this potentiometer. The video output signal is converted into a DC voltage by circuitry within the camera. The potentiometer sets a reference voltage against which this derived DC voltage is compared. If the DC voltage is less than the reference level, the lens iris opening is increased. If the DC voltage is greater than the reference level, the lens iris opening is decreased. This control loop attempts to continually match the DC voltage derived from the video signal, to the reference voltage set by the potentiometer. This feature allows the installer to set the required video output amplitude (e.g. 1Vpp) that the lens should strive to maintain. 7

8 POWER LED ON/OFF In normal operation, the LED on the rear panel of the camera is illuminated when power is connected to the camera. COMPOSITE VIDEO OUTPUT BNC CONNECTOR Connect a video coaxial cable terminated with a 75 Ohm BNC connector to the BNC socket marked VIDEO OUT. POWER SUPPLY Cameras are available in AC mains, and AC and DC low voltage types. The voltage required to operate the camera is clearly marked on the rear panel of the camera. Low voltage cameras must be powered from a UL listed class 2 power supply. The typical power consumption of a camera is less than 5 Watts. Mains power supply: Cameras that are intended to operate directly from the mains supply are fitted with a detachable power supply cord. The operating voltage is 100~250VAC Low Voltage power supply: These cameras are fitted with an automatic switching power supply that will operate between VDC and VAC. Connections are indicated above the terminals on the rear panel of the camera. The power supply must be a UL listed class 2 type. LENS SELECTION Suitable lens types are C and CS mount in fixed iris, manual iris, auto iris or direct drive versions. Cameras are factory set for CS mount lenses. If using a C mount lens, rotate the back focus adjustment mechanism fully clockwise (when viewed from the front of the camera) before fitting the lens, see Back Focus Adjustment. BACK FOCUS ADJUSTMENT Back Focus Adjustment Lock Screw. There is a back focus adjustment accessible at front of the camera housing, that is used to adjust the back focal length or coarse picture focus. The range of adjustment allows both C and CS mount lenses to be used without the need for a spacer ring. To use the back focus mechanism: Figure 1 1. Unlock the back focus mechanism using the Back Focus adjustment lock screw (figure 1). 2. Rotate the back focus adjustment ring as required. When viewed from the front of the camera, clockwise adjustment moves the CCD sensor away from the back of the lens; counter clockwise adjustment moves the CCD sensor towards the back of the lens 3. Lock the back focus mechanism. 8

9 Installing Fixed IRIS lenses & Manual Iris lenses 1. Turn the back focus adjustment ring fully clockwise (when viewed from the front -see Back Focus Adjustment), if using a C-mount lens. 2. Fit the lens to the camera. 3. Ensure the Electronic Iris (EI) and Automatic Gain Control (AGC) features are both turned ON (AUTO or MAN & AES and TURBO). 4. If the lens has an IRIS, open this fully. 5. If the lens has a focusing ring fitted, set it to infinity (00) and then adjust the back focus. 6. If the lens has an IRIS, close accordingly if a greater depth of field is required. Installing Direct (OR D.C.) Drive lenses 1. Turn the back focus adjustment ring fully clockwise (when viewed from the front) if fitting a C-mount lens. 2. Fit the lens to the camera and connect it according to the diagram below. Pin 4 Pin 2 PIN # DC Drive Pin 1 Damp - Pin 2 Damp + Pin 3 Drive + Pin 3 Pin 1 Pin 4 Drive - WARNING The maximum load for this type of lens must not exceed 25mA. 3. Set the lens type selector switch to AUTO (or MAN and AI). 4. Set the AGC switch to AGC. 5. If the lens has a focusing ring fitted, set it to infinity (00) and then adjust the back focus. 6. With typical scene illumination, set the ALC Level adjustment potentiometer for the correct exposure. This can be achieved either visually or more accurately by using an oscilloscope or level meter to set the output of the camera to 1 V peak-peak. 7. Ensure the Automatic Gain Control feature is turned to TURBO. Installing Video Drive Lenses 1. Turn the back focus adjustment ring fully clockwise (when viewed from the front) if fitting a C-mount lens. 2. Fit the lens to the camera and connect it according to the diagram below. GND +12V VIDEO VIDEO LEVEL WARNING The maximum load for this type of lens must not exceed 50mA. 9

10 3. Set the lens type selector switch to AUTO (or MAN and AI). 4. Set the AGC switch to AGC. 5. If the lens has a focusing ring fitted, set it to infinity (00) and then adjust the back focus. 6. With typical scene illumination, set the Lens Level adjustment potentiometer on the lens for the correct exposure. This can be achieved either visually or more accurately by using an oscilloscope or level meter to set the output of the camera to 1 V peak-peak. If the scene lighting conditions are extremely uneven, it may be necessary to adjust the lens's Peak Average potentiometer. Refer to the lens instructions. 7. Ensure the Automatic Gain Control feature is switched to TURBO. CAMERA MOUNTING Mounting points are provided on the top and bottom of the camera and are used to mount the camera on a bracket or tripod. They are designed to accept standard photographic mounting bolts (1/4" BSW or 20 UNC). The mounting bracket must be capable of supporting the weight of the camera and its lens. In cases where the lens is substantially heavier than the camera, it is better to use the mounting point on the lens itself. NOTE: Ensure that any fixings used to mount the bracket are adequate to support the load of the camera and bracket on the surface to which the bracket is fixed. 10

11 SPECIFICATIONS General Wide Dynamic NTSC Dual Power Wide Dynamic PAL Dual Power Wide Dynamic PAL Main Power Image Size 1/3 Format Interline CCD Sensor Ye, Cy, Mg, G, color complementary mosaic filter Pixel Element 768 (H) 494 (V) approx. 380K pixels 752 (H) 582 (V) approx. 440K pixels Scanning Frequency NTSC 2 : 1 Interlace / H : 15750Hz, V : 59.94Hz PAL 2 : 1 Interlace / H : 15625Hz, V : 50Hz Operation Temperature -10 C ~ +50 C Storage Temperature -20 C ~ +60 C Output Terminal BNC 75Ohm Unbalance Input Terminal Dual Power 2 pin Screw Type Terminal Block 2 pin Screw Type Terminal Block Main Power European Power Socket Power Operation Range Dual Power 12VDC +/- 10%, 24VAC +/- 10% 60Hz 12VDC +/- 10%, 24VAC +/- 10% 50Hz Main Power AC100V ~ AC250V 50Hz Power Consumption 4.5W Max. Power Indicator 3ø Green LED on Rear Panel IRIS Connector Video Drive 3pin Push Lock Terminal Block on Rear DC Drive 4pin Connector on Side ( Panasonic Standard ) Lens Mount CS ~ C Mount Adjustable Back Focus Adjust CS Mount 11mm ~ C Mount 18mm Mounting Hole 1/4 Top and Bottom External Dimension 58mmW x 66mmH x 131mmL Functional Specification Exposure Control Auto Detect : Auto Electronics Shutter / Video Auto IRIS / DC Auto IRIS AES Auto Luminance Control 1/60 ~ 1/ sec Max. Auto Luminance Control 1/50 ~ 1/ sec Max Auto IRIS Control Video Drive / DC Drive Separate Output Video IRIS Output 1.0Vpp ( 100IRE Video Output ) DC IRIS Output 650mV at 85Ohm Impendent Wide Dynamic Range 52dB ON / OFF BLC Center Area for Auto IRIS and AES White Balance Auto White Balance Auto White Balance Range 2500K ~ 9500K Day & Night Color Killer Auto Detect by Luminance < Fuzzy 30IRE ~ 80IRE> AGC Boost Enhance AGC Gain to Max. 36dB Color Killer Fuzzy ON / OFF SYNC System INT / Line Lock Line Lock Phase Adjust Range 0 ~ 270 Frequency Range 60Hz +/- 1Hz 50Hz +/- 1Hz Video Specification Resolution Normal Mode 480 TV Line CK Mode 500 TV Line Minimum Illumination F=1.2 ( 50IRE Video Output ) Video Output 1.0Vpp 75Ohm BNC unbalance S/N Ratio 50dB AGC Preset Gain 30dB H Aperture 10 IRE ( r IRE Video Output ) V Aperture 10 IRE ( r IRE Video Output ) Gamma Compensation 0.45 Function Control or Adjustment Exposure Control Auto Detect : Auto Electronics Shutter / Auto IRIS Manual Exposure Control AES / Video Drive / DC Drive Color Killer Fuzzy ON / OFF BLC ON / OFF Switchable Wide Dynamic ON / OFF Selectable SYNC System INT / LL Switchable on Rear Panel V-Phase Via Resistor on Rear panel 11

12 General PAL Hi-Resolution Dual Voltage PAL Hi-Resolution Mains Voltage PAL STD-Resolution Dual Voltage PAL STD-Resolution Mains Voltage CCIR Hi- Resolution Dual Voltage CCIR Hi- Resolution Mains Voltage Image Size 1/3 Format Interline CCD Sensor Ye, Cy, Mg, G, color complementary mosaic filter 1/3 Format Interline CCD Solid State Image Sensor Pixel Element 752 (H) 582 (V) approx. 440K pixels 500 (H) 582 (V) approx.290k pixels 752 (H) 582 (V) approx.440k pixels Scanning Frequency Operation Temperature Storage Temperature Output Terminal Input Termina PAL 2 : 1 Interlace H : 15625Hz, V : 50Hz -10 C ~ +50 C -20 C ~ +60 C BNC 75Ohm Unbalance LV Power 3pin Push Lock Terminal Block Mains Power Figure 8 wire end lead Power Source LV Power DC12V / AC24V +/- 20% Power Consumption Power Indicator IRIS Connector Lens Mount Back Focus Adjust Mounting Hole External Dimension Functional Specification Exposure Control AES Auto IRIS Control Mains Power AC100V ~ AC240V 4.2W Max, 3mm Green LED on Rear Panel DC Iris 4pin Connector on Side ( Panasonic Standard ) Video iris 3pin Push Lock Terminal Block CS ~ C Mount Adjustable CS Mount 11mm ~ C Mount 18mm 1/4 Top and Bottom 67.5mm (W) x 58.5mm (H) x 133.5mm (D) Auto Electronics Shutter / Video Auto RIS / DC Auto IRIS Auto Luminance Control 1/50 ~ 1/ sec Max. Video Drive / DC Drive Video IRIS Output 1.0Vpp ( 100IRE Video Output ) DC IRIS Output BLC White Balance AGC Turbo SYNC System Line Lock Video Specification 650V at 85Ohm Impendent Center Area for Auto IRIS and AES Auto White Balance 2500K ~ 9500K Enhance AGC Gain to Max. 36dB INT / Line Lock Phase Range 0 ~ 270 Frequency Range 50Hz +/- 1Hz CCIR 2 : 1 Interlace H : 15625Hz, V : 50Hz Resolution 480 TV Line 330 TV Line 580 TV Line Minimum Illumination Video Output S/N Ratio AGC LOW Gain AGC HIGH Gain F=1.2 ( 50IRE Video Output ) 1.0Vpp 75Ohm BNC unbalance 50dB 36dB 30dB H Aperture 10 IRE ( r IRE Video Output ) V Aperture 10 IRE ( r IRE Video Output ) Gamma Compensation 0.45 Function Control or Adjustment Exposure Control Lenses Drive BLC AGC Selectable SYNC System V-Phase Lens Level Control Auto Electronics Shutter / Auto IRIS Video or DC Drive - auto detect ON / OFF Switchable AGC Normal / AGC Turbo INT / LL Switchable on Rear Panel Via variable resistor on Rear panel Via Resistor on Rear Panel (For DC Drive Lenses only) F=1.2 ( 50IRE Video Output ) 0.2 F=1.2 ( 50IRE Video Output ) 12

13 General NTSC Hi-Resolution Low Voltage NTSC STD-Resolution Dual Power Image Size 1/3 Format Interline CCD Sensor Ye, Cy, Mg, G, color complementary mosaic filter Pixel Element 768 (H) 494 (V) approx. 380K pixels 510 (H) 492 (V) approx. 250K pixels Scanning Frequency NTSC 2 : 1 Interlace / H : 15750Hz, V : 59.94Hz Operation Temperature -10 C ~ +50 C Storage Temperature -20 C ~ +60 C Output Terminal BNC 75Ohm Unbalance Input Terminal 3pin Push Lock Terminal Block Power Source DC12V / AC24V +/- 20% Power Consumption 4.2W Max, Power Indicator 3ø Green LED on Rear Panel DC Iris 4pin Connector on Side ( Panasonic Standard ) IRIS Connector Video iris 3pin Push Lock Terminal Block Lens Mount CS ~ C Mount Adjustable Back Focus Adjust CS Mount 11mm ~ C Mount 18mm Mounting Hole 1/4 Top and Bottom External Dimension Functional Specification Exposure Control Auto Electronics Shutter / Video Auto RIS / DC Auto IRIS AES Auto Luminance Control 1/60 ~ 1/ sec Max. Auto IRIS Control Video Drive / DC Drive Video IRIS Output 1.0Vpp ( 100IRE Video Output ) DC IRIS Output 650V at 85Ohm Impendent BLC Center Area for Auto IRIS and AES White Balance Auto 2500K ~ 9500K AGC Boost Enhance AGC Gain to Max. 36dB SYNC System INT / Line Lock Line Lock Phase Range 0 ~ 270 Frequency Range 60Hz +/- 1Hz Video Specification Resolution 480 TV Line 330 TV Line Minimum Illumination F=1.2 ( 50IRE Video Output ) Video Output 1.0Vpp 75Ohm BNC unbalance S/N Ratio 50dB AGC HIGH Gain 36dB AGC LOW Gain 30dB H Aperture 10 IRE ( r IRE Video Output ) V Aperture 10 IRE ( r IRE Video Output ) Gamma Compensation 0.45 Function Control or Adjustment Exposure Control Auto Electronics Shutter / Auto IRIS Lenses Drive Video or DC Drive - auto detect BLC ON / OFF Switchable AGC Selectable AGC Normal / AGC Turbo SYNC System INT / LL Switchable on Rear Panel V-Phase Via variable resistor on Rear panel Lens Level Control Via Resistor on Rear Panel (For DC Drive Lenses only) 13

14 General EIA Hi-Resolution Dual Power Image Size 1/3 Format Interline CCD Solid State Image Sensor Pixel Element 768 (H) 494 (V) approx. 380K pixels Scanning Frequency EIA 2 : 1 Interlace / H : 15750Hz, V : 59.94Hz Operation Temperature -10 C ~ +50 C Storage Temperature -20 C ~ +60 C Output Terminal BNC 75Ohm Unbalance Input Terminal 3pin Push Lock Terminal Block Power Source DC12V / AC24V +/- 20% Power Consumption 3.2W Max, Power Indicator 3ø Green LED on Rear Panel DC Iris 4pin Connector on Side ( Panasonic Standard ) IRIS Connector Video iris 3pin Push Lock Terminal Block Lens Mount CS ~ C Mount Adjustable Back Focus Adjust CS Mount 11mm ~ C Mount 18mm Mounting Hole 1/4 Top and Bottom External Dimension Functional Specification Exposure Control Auto Electronics Shutter / Video Auto RIS / DC Auto IRIS AES Auto Luminance Control 1/60 ~ 1/ sec Max. Auto IRIS Control Video Drive / DC Drive Video IRIS Output 1.0Vpp ( 100IRE Video Output ) DC IRIS Output 650V at 85Ohm Impendent BLC Center Area for Auto IRIS and AES AGC Boost Enhance AGC Gain to Max. 36dB SYNC System INT / Line Lock Line Lock Phase Range 0 ~ 270 Frequency Range 60Hz +/- 1Hz Video Specification Resolution 580 TV Line Minimum Illumination 0.2 F=1.2 ( 50IRE Video Output ) Video Output 1.0Vpp 75Ohm BNC unbalance S/N Ratio 50dB AGC Turbo Gain 36dB AGC Preset Gain 30dB H Aperture 10 IRE ( r IRE Video Output ) Gamma Compensation 0.45 Function Control or Adjustment Exposure Control Auto Electronics Shutter / Auto IRIS Lenses Drive Video or DC Drive - auto detect BLC ON / OFF Switchable AGC Selectable AGC Normal / AGC Turbo SYNC System INT / LL Switchable on Rear Panel V-Phase Via variable resistor on Rear panel Lens Level Control Via Resistor on Rear Panel (For DC Drive Lenses only) 14

15 Drawing and Dimension - standard Range Camera 15

16 Drawing and Dimension Wide Dynamic Camera 16

Fixed Color Cameras Installation Manual INTRODUCTION These instructions cover the American Dynamics ADCA470 and ADCA330 series of color cameras Read a

70 Fixed Color Cameras ADCA330CN ADCA330CP ADCA470CAFN ADCA470CAFP Installation Manual Fixed Color Cameras Installation Manual INTRODUCTION These instructions cover the American Dynamics ADCA470 and ADCA330