VFS3 WIRELESS VIDEO FIBERSCOPE

Transcription

1 VFS3 WIRELESS VIDEO FIBERSCOPE TACTICAL ELECTRONICS Products OPERATION AND SUPPORT PUBLICATION PROPRIETARY TACTICALELECTRONICS.COM PRODUCTS / EOD TRAINING / R & D / AVIATION DESIGN / ENGINEERING / MANUFACTURING HEMLOCK FACILITY 2200 NORTH HEMLOCK AVE / BROKEN ARROW, OK / V: / V: / F: CRUSADER FACILITY 2844 CRUSADER CIRCLE / #100 / VIRGINIA BEACH, VA / V: / F:

2 PROPRIETARY 2

3 3 VFS3 WIRELESS VIDEO FIBERSCOPE Manual Contents Kit Identification Power-up Operation Monitoring Options Specifications

4 VFS3 KIT CONTENTS 4 One) Video Fiberscope specifically designed for EOD operations 8mm diameter probe, with four-direction articulation up to probe length, sealed with a non-conductive, weather proof coating lux sensitized black & white CCD chip at the distal end of the probe Wireless video transmission Hard-wire capable (HMM required) Internal light source Powered by 3V Lithium CR123 cells (OTS) One) Hard-wire option cable One) Monitoring option of your choice (Heads-Up Display, Handheld, Wrist Mounted, or MMV) The HUD gives the operator the appearance of a 35-inch screen at a 7 foot distance. Handheld Monitor with 5.0 LCD screen Wrist Mounted Monitor gives the operator a 3.5 screen on the arm The Monocular Micro Viewer is a four channel, single eyepiece monitor that can be attached to a lanyard and hung around the neck. One) Storm Case w/ precision cut foam for stable storage environment Unbreakable Watertight Airtight Corrosion Proof One) Focus Tool

5 VFS3 POWER UP 5 The VFS3 Wireless Video Fiberscope is powered by four 3Volt Photo Lithium batteries. Most manufacturers of these cells designate them as size 123 or CR123A. Tactical Electronics systems draw high current, and we only recommend use of SUREFIRE, GE SANYO, ENERGIZER, or DURACELL batteries. Testing has proven those batteries to provide the longest run time in our products. Though run times will vary, components in this system are designed to optimize power management and power sharing when hard-wired together. The diagrams below demonstrate proper battery installation and power-up for the VFS3 Video Fiberscope. Battery Compartment & Power-Up Procedure: The VFS3 (left) requires four 3V Lithium batteries for operation. Use the battery orientation diagram adhered to the VFS3 for reference. NOTE: For SD card recording, ensure the SD card is inserted before powering ON the VFS3. * Always remove batteries when not in use The power switch for the VFS3 is a rubber push button located on the side of the unit. Fully depress the power button to power ON and OFF the VFS3. Immediately after the VFS3 is powered ON the LED indicator will illuminate a solid blue for approximately 8-10 seconds while the system initializes. Once the power-up phase is complete the LED indicator will illuminate a solid green indicating full operational use (If no SD card is inserted, the LED indicator will flash red). NOTE: When the VFS3 is powered ON the internal light source is powered OFF by default. Power Button To power OFF the VFS3, hold down the power button for 3 seconds to begin power down cycle - when the LED illuminates blue release the power button and the unit will power OFF within seconds. NOTE: DO NOT open the battery door before powering OFF the VFS3. Failure to properly power OFF the unit will result in loss of recorded files. LED Indicator: The LED power indicator will illuminate red to indicate low battery power. After the LED illuminates solid red the unit will shut down within 10 minutes. LED indicator When battery life is critical the LED indicator will illuminate solid blue. Once this occurs the VFS3 will only remain ON for seconds while the system shuts down to protect recorded files on the SD card.

6 VFS3 OPERATION 6 VFS3 Articulation To the left is a top view of the VFS3 articulation control paddles. As labeled, the paddle on the left controls camera movement RIGHT and LEFT while the paddle on the right controls camera movement UP and DOWN. When moving the paddles you will hear them clicking as well as feel them sliding through locking positions. Normal rotation like this is for quick camera movements to new positions. To scan an inspection area you can depress the paddles for fine or smooth adjustments. After pressing the paddles down, gently move them in the desired direction for a fluid articulation of the probe. Once the paddles are released they will lock into the desired position. WARNING: Forced or quick movement of the adjustment paddles can severely damage the VFS3. The diagram to the left depicts the distal probe or camera in its articulated states. The probe of the fiberscope articulates in four directions up to 160. DO NOT attempt to move, or in any way, manually manipulate the articulating neck of the VFS3. ALWAYS use the articulation control paddles.

7 VFS3 OPERATION 7 SD Card Recording: Insert the SD card into the SD card slot with the VFS3 powered OFF. DO NOT insert or eject the SD card with the VFS3 powered ON; otherwise, recorded video files will not finalize and will become corrupted. Immediately after the VFS3 is powered ON, the LED indicator will illuminate a solid blue for approximately 2-5 seconds while the system initializes. Once the power-up phase is complete the LED indicator will illuminate a solid green indicating operational use and proper SD card recording. If the VFS3 system indicates a recording error, REC ERROR will display on the monitor(s) in use. If REC ERROR is displayed, power OFF the VFS3, reinsert the SD card, and power ON the unit. The VFS3 will transmit video without the use of SD card recording. If the unit is powered ON without an SD card inserted "REC ERROR" will be displayed on the monitor(s) in use. The LED indicator on the VFS3 will also flash red to indicate no SD card present. SD Card Viewing: * Push in SD Card to eject To review recorded video files: Power OFF the VFS3, eject the SD card, and insert the SD card into an SD card reader on a computer. All files will be under the folder DCIM\100Media on the SD card. Recorded files will be listed sequentially in numerical order. All recorded video files are AVI files, and are easily viewed in Windows Media Player or VideoLan's VLC Player. AVI files may also be viewed in QuickTime with the appropriate plug-in. Snapshot Still Image Capture: The VFS3 has a SNAPSHOT still image capture feature that records a still image to the SD card. To capture a still image, simply depress the SNAPSHOT button while recording video to the SD card.

8 VFS3 OPERATION 8 VFS3 Focus Tool The focus tool (left) is used to adjust the focal length of the VFS3. The focus tool is supplied in a protective plastic container. Observe that the tool has a hexagon protrusion on one end. This protrusion is to be inserted over the lens located inside the distal end of the probe (visible under close inspection). Proper alignment of the focus tool is necessary to accomplish focus adjustment and to prevent damage to the lens. Once the tool is properly aligned and inserted, it can be twisted clockwise and counter-clockwise to focus the scope. When making the adjustment, secure the distal tip of the probe with your forefinger and thumb. DO NOT bend or otherwise articulate the scope. WARNING: Continued turning of the lens with the focus tool will unscrew the lens completely from the distal tip. After adjusting the focus, remove the focus tool before using the VFS3. Internal Light Source The VFS3 utilizes an internal light supplement to emit light from the distal end of the probe. The internal light supplement has brightness controls located on the side of the unit. Depress the up and down BRIGHTNESS buttons to increase or decrease the intensity of the light. WARNING: When using the Near UV External Light Source, practice extreme caution. This device radiates intense Ultraviolet (UV) light when operated. Exposure to UV radiation can be harmful to your health. Protect your eyes and skin during operation. DO NOT look directly at this device during operation. Exposure to UV light, even for a brief period, can damage your eyes.

9 VFS3 OPERATION 9 Wireless Transmission: Wireless operation of the VFS3 is very simple. Follow proper VFS3 power-up procedure and the unit will automatically transmit wireless video signals. Once the VFS3 is powered ON, the unit immediately begins transmission of an RF video signal. When a monitor is powered ON the monitor begins receiving the video signal from the VFS3. Cycle through the channels on the monitor until a picture is displayed on the monitor screen. Hard-Wire Transmission: The 0.25 inch jack (shown left) is used for hard-wire operation between the VFS3 and the Handheld Monitor. Simply power ON both the VFS3 and Handheld Monitor, then insert the male/male cable into the 0.25in jacks on each unit. Hard-wire operation disables the wireless signal. 0.25in jack NOTE: When working in extreme low light environments hardwire (if possible) the Handheld Monitor to the VFS3. A hardwire connection provides a slightly brighter picture on the Handheld Monitor. Channel Selector: To determine which channel the VFS3 is transmitting, simply power ON both the VFS3 and monitor. Use the channel selector button(s) on the monitor to cycle through each channel until a picture is displayed on screen. Outgoing channel selector

10 MONITOR OPTIONS 10 Tactical Electronics video systems are designed to operate interchangeably with each wireless monitor: Wrist Mounted Monitor (WMM), Handheld Monitor (HHM), Monocular Micro Viewer (MMV), Heads-Up Display (HUD), Wrist Mounted Monitor Pro (WMM Pro), or Handheld Monitor Pro (HHM Pro). Each monitor is programmed to receive a frequency transmitted directly from the purchased camera system. If multiple camera systems are in use, the monitors are equipped to receive separate channel frequencies in order to view and cycle between various Tactical Electronics camera systems. Wrist Mounted Monitor (WMM) The Wrist Mounted Monitor is powered by two 3V Lithium batteries. The batteries are to be inserted positive (+) terminal first. The power switch for the Wrist Mounted Monitor (left) is the top button near the battery cap. Press and hold the power button for approximately 3 seconds to power ON the WMM. The screen will display the current channel and battery power meter when the unit is ON. Always remove batteries when not in use. IMPORTANT: If lines begin to appear across the screen, the lines are most likely a sign of LOW BATTERIES. Power WMM Operation The Wrist Mounted Monitor has a 3.5 inch LCD screen that displays B/W or color video transmitted from the camera source. The monitor contains an internal receiver, and when powered ON automatically receives RF video signals from the chosen camera. The WMM is completely wireless and cannot be hardwired. WMM Channel Selection If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. Channel Selector To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen.

11 MONITOR OPTIONS 11 Handheld Monitor (HHM) The Handheld Monitor (HHM) is powered by four 3V Lithium batteries, AC, or vehicle power via cigarette lighter plug. Batteries are to be inserted positive (+) terminal first. The power button for the Handheld Monitor (left) is a rubber push button located on the top of the unit. Depress the power button to power ON the monitor. Hold down the power button for 5 seconds to power OFF the monitor. IMPORTANT: ALWAYS REMOVE BATTERIES WHEN NOT IN USE. If lines begin to appear across the screen, the lines are most likely a sign of low batteries. HHM Operation The Handheld Monitor has a 5.7in LCD screen that displays B/W or color video transmitted directly from the camera source. Power The monitor has a built-in receiver and when powered ON automatically receives an RF video signal until a hard-wire is plugged in or the HHM is powered OFF. The HHM has three brightness levels, a single depress on the power button will cycle through the three brightness levels. HHM Channel Selection Channel Selector If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Due to RF video transmission, slight adjustments in your viewing angle can greatly affect the quality of the picture. Video Out Jack Hard-wire Connection & Video Output The Handheld Monitor provides a direct hard-wire connection to compatible camera systems. Hard-wire Jack NOTE: When working in extreme low light environments hardwire the Handheld Monitor to the camera system. A hard-wire connection provides a slightly brighter picture on the Handheld Monitor, this feature is beneficial for low light situations. Video displayed on the Handheld Monitor can also be output through the video output jack. Simply connect an RCA cable to the Handheld Monitor and another monitor for video out.

12 MONITOR OPTIONS 12 Monocular Micro Viewer (MMV) The MMV is powered by one 3V Lithium battery. Unscrew the battery cap [shown left] to insert the battery. The 3V Lithium battery is to be inserted according to the battery orientation diagram on the MMV. Always remove batteries when not in use. battery cap The power button for the MMV (left) is a rubber push button on the side of the unit. The LED indicator will illuminate green and the video display will slightly illuminate when the unit is powered ON. NOTE: The On Screen Display (OSD) will show a flashing battery icon when the battery is close to critically low levels. LED Indicator POWER The LED will momentarily light up blue when the unit is first powered on, then will illuminate solid green. The LED will illuminate blue whenever the channel button is pressed. The LED will momentarily illuminate red when the unit is powering down. The LED will illuminate solid red when the battery is low. Automatic Shutdown To preserve battery life the MMV will automatically shut off if the unit is idle for approximately 90 seconds. When the unit is nearing automatic shutdown the OSD will show a series of disappearing dots as a countdown timer. To prevent automatic shutoff: Press the channel button once to reset shutdown timer, allowing another 90 seconds of video display. A single press of the channel button will also display the current channel the MMV is receiving. Wireless Video The MMV has a built-in receiver, and when powered ON automatically receives RF video signals from the chosen camera. The MMV is completely wireless and cannot be hard-wired. channel selector If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Any time the channel is changed on the MMV the shutdown timer is reset. Since the initial press of the channel button resets the shutdown timer and displays the current channel, it is necessary to press the channel button more than once to change channels.

13 MONITOR OPTIONS 13 Heads-Up Display (HUD) The Heads-Up Display is powered by two 3V Lithium batteries, The 3V Lithium batteries are to be inserted positive ( + ) terminal first. Always remove batteries when not in use. The power switch for the Heads-Up Display (left) is a rubber push button on the front of the unit. The display slightly illuminates when the HUD is powered ON. To power OFF the HUD press and hold the power button. A red LED in the left eyepiece will illuminate momentarily, indicating the unit is ready to power down. Release the power button. NOTE: The On Screen Display (OSD) will show a flashing battery icon when the battery is close to critically low levels. HUD Operation POWER The Heads-Up Display gives the operator the appearance of a 35-inch screen at a 7 foot distance. The HUD displays B/W or color video transmitted directly from the camera source. channel selector It has a built-in receiver, and when powered ON automatically receives RF video signals from the chosen camera. The HUD is completely wireless and cannot be hard-wired. HUD Mounting The HUD comes standard with the Wilcox 14001G01 Wilcox NVG Mounting Shoe. This mounting shoe is compatible with most Wilcox NVG Mounting Systems. To mount the HUD to the Wilcox NVG Mount, slide the attached mounting shoe into the appropriate slot on the NVG Mount until the HUD system clicks solidly into place. Detach the HUD from the NVG Mount using the release mechanism on the NVG Mount. HUD Channel Selection If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. Note: The first press of the channel selector button will display which channel the HUD is receiving as well as current battery power. To change the channel press the channel selector button again within three seconds.

14 PRO MONITOR OPTIONS 14 Wrist Mounted Monitor Pro (WMM Pro) The Wrist Mounted Monitor Pro is powered by two 3V Lithium batteries. The batteries are to be inserted positive (+) terminal first. The power switch for the WMM Pro (left) is the top button near the battery cap. Press and hold the power button for approximately 3 seconds to power ON the monitor. The screen will display the current channel and battery power meter when the unit is ON. Always remove batteries when not in use. IMPORTANT: If lines begin to appear across the screen, the lines are most likely a sign of LOW BATTERIES. Power WMM Pro Operation The WMM Pro has a 3.5 inch LCD screen that displays B/W or color video transmitted from the camera source. The monitor contains an internal receiver, and when powered ON automatically receives RF video signals from the chosen camera. The WMM Pro is completely wireless and cannot be hard-wired. Remote Toggle If the camera system in operation is capable of remote toggling follow the instructions below to toggle between camera views and/or IR LED illumination modes. Camera Toggle IR Toggle Remote toggle camera views: Depress the Camera button on the Wrist Mounted Monitor Pro to remotely toggle between separate camera views. Remote toggle of IR illumination: Depress the IR button on the Wrist Mounted Monitor Pro to remotely toggle through IR LED illumination modes. WMM Pro Channel Selection Channel Selector If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When cycling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Slight adjustments in your viewing angle can greatly affect the quality of the picture.

15 PRO MONITOR OPTIONS 15 Handheld Monitor Pro (HHM Pro) The Handheld Monitor Pro (HHM Pro) is powered by four 3V Lithium batteries, AC, or vehicle power via cigarette lighter plug. Batteries are to be inserted positive (+) terminal first. The power button for the Handheld Monitor Pro (left) is a rubber push button located on the top of the unit. Depress the power button to power ON the monitor. Hold down the power button for 5 seconds to power OFF the monitor. Power IMPORTANT: ALWAYS REMOVE BATTERIES WHEN NOT IN USE. If lines begin to appear across the screen, the lines are most likely a sign of low batteries. The HHM Pro has three brightness levels, a single depress on the power button will cycle through the three brightness levels. Remote Toggle IR Toggle If the camera system in operation is capable of remote toggling follow the instructions below to toggle between camera views and/or IR LED illumination modes. Remote toggle camera views: Depress the Camera button on the Handheld Monitor Pro to remotely toggle between separate camera views. Remote toggle of IR illumination: Depress the IR button on the Handheld Monitor Pro to remotely toggle through IR LED illumination modes. Camera Toggle Channel Selector Video Out Jack HHM Channel Selection If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Due to RF video transmission, slight adjustments in your viewing angle can greatly affect the quality of the picture. Hard-wire Connection & Video Output Hard-wire Jack The Handheld Monitor Pro provides a direct hard-wire connection to compatible camera systems. When working in extreme low light environments hard-wire the Handheld Monitor to the camera system. A hard-wire connection provides a slightly brighter picture on the monitor, this feature is beneficial for low light situations. Video displayed on the Handheld Monitor Pro can also be output through the video output jack. Simply connect an RCA cable to the Handheld Monitor Pro and another monitor for video out.

16 SPECIFICATIONS 16 SPECIFICATIONS WEIGHT: DIMENSIONS (L X W X H): POWER SUPPLY: RUNTIME: RUNTIME (SD + LED): RUNTIME (LED): HOUSING MATERIAL: OPERATING TEMPERATURE RANGE: FREQUENCY RANGE: TRANSMISSION DISTANCE: COMPATIBLE MONITORS: CAMERA RESOLUTION: CAMERA LIGHT SENSITIVITY: FIELD OF VIEW: PROBE LENGTH: PROBE DIAMETER: PROBE SHEATHING: ARTICULATION: LIGHT SOURCE COLORS AVAILABLE: HARD-WIRED VIDEO OUTPUT: 1.26 lbs 20.5in x 2.62in x 3.27in Four 3V Lithium batteries (CR123A type) 5 hours 3 Hours 4.5 Hours High-density polyethylene (HDPE), anodized aluminum -10ºC to +50ºC, 95% humidity 2.4 to Ghz (4 channel system) Up to 450ft line of sight Wrist Mounted Monitor / Handheld Monitor / Heads-Up Display / Monocular Micro Viewer / Wrist Mounted Monitor Pro / Handheld Monitor Pro 400 lines lux 58 degrees 10 inches 8mm Non-conductive PVC-heavy duty tungsten braid 4-way 160 degrees up, 130 degrees down, 100 degrees left and right Green, Blue, White, EOD, and IR 850nm 1/4 inch stereo jack RECORDING SPECIFICATIONS: STORAGE MEDIA: RECORDING CAPACITY: SDHC memory card (16GB SDHC card included with system) 16 hours on 16GB SD card (1GB/hour) WARNING: When using the Near UV External Light Source, practice extreme caution. This device radiates intense Ultraviolet (UV) light when operated. Exposure to UV radiation can be harmful to your health. Protect your eyes and skin during operation. DO NOT look directly at this device during operation. Exposure to UV light, even for a brief period, can damage your eyes Tactical Electronics and Military Supply, L.L.C. All Rights Reserved. Product specifications and information are subject to change without notice. If you encounter any problems with your system, please contact us immediately: Tactical Electronics P.O. Box 152 Broken Arrow, OK (866) TACTICALELECTRONICS.COM PRODUCTS / EOD TRAINING / R & D / AVIATION DESIGN / ENGINEERING / MANUFACTURING HEMLOCK FACILITY 2200 NORTH HEMLOCK AVE / BROKEN ARROW, OK / V: / V: / F: CRUSADER FACILITY 2844 CRUSADER CIRCLE / #100 / VIRGINIA BEACH, VA / V: / F: