OPERATION MANUAL LENS CONTROLLER

Transcription

1 OPERATION MANUAL LENS CONTROLLER PTM-ZCB

2 CONTENTS 1.INTRODUCTION 2.ATTENTION 3.ACCESSORY 1P 2P 2P 4.PART NAME AND FUNCTION 3P 5.GUARANTEE / SERVICE 6.SPECIFICATION 6P 7P 1.INTRODUCTION Please read this "Manual" before using, Read this "Manual" before using, Please confirm and use that the operated machine is set up and connected correctly. Please keep this manual and written guarantee, after it reads. This machine is controller for camera with zoom lens, PAN/TILT, wiper, dome camera and relay BOX. Lens, wiper, and PAN/TILT can be easily operated remotely. Please use this machine after confirming the operation functions such as camera and PAN/TILT * The sign bellow is used in this manual. Picture display example This picture is warning and caution This picture is directs the act. This picture is prohibits the act. 1

3 2.ATTENTION Warning If you do not follow the following instructions, it causes serious accidents such as electric shocks and flames. Please do not use in situation which water is sprinkled, and water splashes It causes the short and the electric shock. Please use only the exchange adaptor of the attachment. There is fear of a fire and the electric shocks, it becomes the cause of malfunction Please do not dismantle the main body. It causes the breakdown. Caution if you do not follow the following instructions, might it injure and it cause disadvantageous accident. If you put in and pull out the power plug with a wet hand, it might cause an electric shock. If water and the substance enter machine, it might cause a fire. Please discontinue using at once, when water and substance enter machine by any chance, and consult the shop This machine is class B info tech equipment based on the standard Voluntary Control Council for Interference by Information Technology Equipment. This machine has aim to use by home environments, if receiving trouble might be caused when this device is adjacent to radio and television. Please do correct handling according to the manual. 3.ACCESSORY The following accessories are bundled to this machine and confirm it, please. Manual (this magazine) Manual (safety) AC adaptor Written guarantee 2

4 4.PART NAME AND FUNCTION Display LED 1 MANUAL IRIS AUTO MAUAL mode display LED (Orange color) When IRIS control by manual, LED is lit. 2 X2 EXTENDER display LED (Orange color) When EXTENDER ON/OFF moves, it is lighting and lights-out. When EXTENDER cable of the lens is connected, it is always lighting. LED shines brightly by ON action, it is lights-out by OFF action. 3 OPERATION INDICATOR OPERATION INDICATOR display LED (Yellow color) LED is lighting when operation button is pushed certainly. However, when ON/OFF button of EXTENDER is operated, LED lights by only OFF operation. 4 OPERATION INDICATOR MOVEMENT INDICATOR display LED (Green color) LED lights when the lens motor is driven. When auto/manual change operation of IRIS,LED is not lighting. 3

5 Operation button switch (SW) 5 IRIS MODE Auto / Manual mode change button switch of IRIS 6 EXTENDER ON / OFF change button switch of EXTENDER 7 OPEN Operation button switch of IRIS IRIS is opened. 8 CLOSE Operation button switch of IRIS IRIS is closed. 9 FAR Operation button switch of FOCUS FOCUS is kept away. 10 NEAR Operation button switch of FOCUS FOCUS is brought close. 11 TELE Operation button switch of ZOOM Lens move to TELE side. 12 WIDE Operation button switch of ZOOM Lens move to WIDE side. 7 ~ 12 operation button switch changes the output voltage by pushed time. Voltage goes up when keeping pushing, and movement of the lens motor quickens. OPERATION INDICATOR shows change in voltage. Brightness of operation indicator LED (Green color) Caution:Please operate SW button surely slowly. 4

6 Back connector / Terminal switch Caution:The lens that can be controlled with this machine is one. Back connector 13 OUT1, 14 OUT2, 15 CONNECT LENS CABLE Please connect lens drive cable with one place. 13 OUT1 Connector for external lens connection (Mini DIN 8P) Pin Assign Pin No. Signal 1-2 EXT. 3 ZOOM 4 FOCUS 5 IRIS 6 COMMON 7 IRIS MODE 8 GND 14 OUT2 Connector for external lens connection (Modular Jack 8P) Pin Assign Pin No. Signal 1 FOCUS 2 ZOOM 3 IRIS 4 EXT. 5 COMMON 6 COMMON 7 IRIS MODE 8 GND 5

7 15 CONNECT LENS CABLE Terminal for lens connection The drive cable from lens is connected. FOCUS : Please connect FOCUS cable. ZOOM : Please connect ZOOM cable. IRIS : Please connect IRIS cable. EXT. : Please connect EXT. cable. COMMON : Please connect COMMON cable, or one side of FOCUS, ZOOM, IRIS, EXT. cable. IRIS MODE : Please connect AI/MI change cable. GND : Please connect AI/MI change cable GND. electric wire size Single core φ1.0mm ( AWG18 ) Multi core 0.75m m2 ( AWG20 Composition φ0.18over ) Range of electric wire that can be used Single core φ0.4~1.2mm ( AWG26~16 ) Multi core 0.2~0.75m m2 ( AWG24~20 Composition φ0.18over ) 16 DC12V DC Jack Please insert plug of attachment AC adaptor. Caution:This machine might break down when you use other AC adaptors, Our company cannot assume the responsibility. Moreover, please do not remodel the AC adaptor. 17 POWER POWER SW 5.GUARANTEE / SERVICE The written guarantee is attached to this product. Please preserve it. Guaranteed term The guaranteed term is one year from the purchased day. When the repair is requested, please often read each item of this manual and examine it again. Please inform the shop that purchases it as follows how the condition is bad. Name of articles, type name, and purchase time Name and point Telephone number The breakdown symptom is detailed. 6

8 6.SPECIFICATION Item Environment Power supply CONTENT Indoor / Desk-top etc. Accessories AC adapter (DC12V Output) AC100V~220V 50/60Hz Power consumption 0.4A Operating temperature / humidity Dimension Weight Case material Cable length 0~40 / 35~90% Width:162 mm Depth:110 mm Height:47 mm 0.6kg(Not contain accessories) Steel plate, Aluminum alloyl Ivory Tokina Co.,Ltd NISHI -OCHIAI, SHINJUKU -KU, TOKYO JAPAN PHONE :