INSTALL GUIDE FORD SYNC2/SYNC3 SINGLE/DUAL CAMERA INTERFACE ARC-MFTCAM
|
|
- Domenic Cameron
- 5 years ago
- Views:
Transcription
1 INSTALL GUIDE FORD SYNC2/SYNC3 SINGLE/DUAL CAMERA INTERFACE ARC-MFTCAM Updated
2 SYNC2/SYNC3 DISPLAYS Use this manual for adding backup camera and/ or auxiliary camera on Ford 8 Sync 2, 8 Sync 3, or 4 Sync 3 display vehicles. These vehicles should all have a display connected directly to a SYNC module. For 4 Displays with a 12-pin connector, see 4 MyFord install manual. CONTENTS * 3 MODULE CONFIGURATION START HERE! * 4 ADDING 2ND CAM TO FACTORY CAM * 6 ADDING BACKUP CAM + OPTIONAL 2ND * 8 CAMERA OPERATION & BEHAVIOR 3 Module Configuration Module must be configured before first use. Set DIP switches using a pick or suitable tool to the desired configuration while the module is not connected to the vehicle. Switches 1-5 set the configuration, #6 sets the camera behavior, and 7 and 8 should be set to on. See the following sections for more information. MODULE CONFIGURATION Without Factory Backup Camera * 9 AUXILIARY CAMERA ACTIVATION Easy-read Install Manual Use only the orange highlighted tab specific to the product you are installing! * 13 TROUBLESHOOTING Before Installing: Disconnect negative battery terminal before beginning instllation! DIP Switches must be set before installation of interface module! For vehicle specific instructions for dash disassembly, reference workshop manual. WITH Factory Backup Camera *For both Satellite Radio and Camera add-on, contact supplier. NOTE: Modules can only be used on ONE vehicle. The unit is locked by VIN and can be used more than once ONLY on the same vehicle in case modules are accidentally reprogrammed.
3 POWER AND SIGNAL CONNECTION For adding auxiliary camera AUXILIARY CAMERA ADD-ON with FACTORY Backup Camera (Aux Add-On ONLY) For all other applications, continue to next page. 1. Connect 6-pin molex connector from vehicle specific T-Harness & 12-pin molex connector from ARC-357 accessory harness to the Interface Module. 2. Connect RCA connectors from ARC-357 Accessory Harness to T-harness as pictured. Connect OEM Cam Out to Rear Cam Input. 3. Connect camera power to Accessory +12V output & supplied ground. Do not use reverse power for camera. See Diagram, next page 4. Auxiliary Camera Connection: See Diagram, next page 5. Auxiliary Camera Activation: See Page 8,9 4 Accessory Power & RCA Connections 5 Proceed to Aux Cam Activation - Page 8 NO PROGRAMMING NECESSARY
4 POWER AND SIGNAL CONNECTION Adding Backup camera + Optional Aux Camera BACKUP CAMERA ADD-ON + Optional 2nd Camera - Without Factory Backup Camera 1. Connect 12-pin molex connector from ARC-357 accessory harness to the Interface Module. 2. Connect RCA connectors from ARC-357 Accessory Harness to T-harness as pictured. 3. Connect camera power to Accessory +12V output & supplied ground. Do not use reverse power for camera. See Diagram 4. Auxiliary Camera Connection/Activation: See Page 8,9 6 Accessory Power & RCA Connections 7 PROGRAMMING INSTRUCTIONS 1. With vehicle Ignition OFF Install T-Harness behind FCDIM (Display). Connect vehicle battery at this time. A2 - ACM PROGRAMMING and J1 Jumper remain connected at this time. 2. Connect module to 6-Pin Connector A1 - APIM PRO- GRAMMING. 3. Turn vehicle Ignition to ON/RUN. Do not start vehicle. 4. Programming will initiate automatically at this time. Radio/ Display should reset twice at this point. Traction Control Disabled will be displayed on the instrument cluster temporarily on compatible vehicles to show that APIM programming has completed successfully. 5. Turn vehicle Ignition OFF, remove module from A1, remove Jumper J1 from harness. 6. Connect module to A2. The module will reside on this connector for normal vehicle operation. 7. Test Programming by placing vehicle in reverse with foot firmly on the brake, and clear surroundings. 8. If programming is unsuccessful, turn key off, disconnect module, verify DIP switch settings, and perform procedure again.
5 CAMERA OPERATION For Satellite Radio skip to Page 10 8 Auxiliary Camera Activation: 9 IMPORTANT NOTES If camera functionality is tested without camera(s) fully powered and connected, system may display a Camera not Available message and will temporarily disable camera input. Allowing the vehicle to sit for 5 minutes with ignition off will reset the function. Camera Operation & Behavior Display may stay in reverse camera mode until vehicle is driven to 7MPH. This is a factory function and cannot be changed. Manual Activation On compatible vehicles, the secondary camera can be activated by pressing and holding the OK button for 3 seconds on either the radio controls, or the steering wheel. Press the OK button once more to return to normal operation. If the OK Button does not work, try the SYNC Voice command button. See diagrams The green manual activation wire can be connected to +12V or Ground to manually activate the secondary camera. This can also be adjusted to only recognize either using the ARC 357 PC Configuration Tool. Blind Spot mode will automatically activate the aux camera with the right blinker in compatible vehicles. If your vehicle is not compatible, you will need to use the manual trigger wire. Make sure Blind Spot activation is turned on using the ARC 357 PC Configuration Tool. Default Auxiliary Camera Behavior Front/Aux/Cargo Mode DIP Switch #6 = OFF Speed Limited to 7MPH* No activation time limit For off-road use only Backup Camera Priority over Auxiliary Camera* Blind Spot/Aux Mode DIP Switch #6 = ON Time Limited to 30 Seconds* No activation speed limit Automatic right blind spot triggering in compatible vehicles* *Can be adjusted with ARC-357 PC Configuration Tool Before Installing: Disconnect negative battery terminal before beginning instllation! DIP Switches must be set before installation of interface module! For vehicle specific instructions for dash disassembly, reference workshop manual. ARC-357 Configuration Tool Use the ARC 357 Configuration tool to set custom options for your custom install For Blind Spot Camera installations, enable automatic blind spot activation in compatible vehicles, adjust maximum camera on time. (DIP Switch #6 should be set to ON) For Cargo Camera installations, disable backup camera priority to allow the cargo cam to be used when lining up a trailer or camper. For Front Camera installations, adjust maximum speed that camera can operate at (DIP Switch #6 should be set to OFF) *Requires Micro-USB Cable (Not included) Update firmware, check VIN lock, set custom options, and more! Free download on
6 NOTES 10
ARCMFT2CAM INSTALL GUIDE FORD SYNC2/SYNC3 SINGLE/DUAL CAMERA INTERFACE ARC-MFT2CAM
ARCMFT2CAM111618 INSTALL GUIDE FORD SYNC2/SYNC3 SINGLE/DUAL CAMERA INTERFACE ARC-MFT2CAM Updated 01.16.2019 SYNC2/SYNC3 DISPLAYS Use this manual for adding backup camera and/ or auxiliary camera on Ford
More informationINSTALL GUIDE 4 MYFORD APPLICATIONS ARC-MFCAM357 ARC-MFMULTICAM ARC-MFSAT357
INSTALL GUIDE 4 MYFORD APPLICATIONS MYFORD 4 DISPLAYS Use this manual for adding backup camera, auxiliary camera, and/or satellite radio to Ford vehicles with a 4 MyFord display with 12-pin connector.
More informationMOD MyFord 4 Installation Manual
250-8419-MOD MyFord 4 Installation Manual Full plug and play programming and power kit, for Ford Vehicles with a camera-compatible 4" MyFord Display Required for Install: 1. Ford Vehicle with camera-compatible
More informationMOD MyFord Touch Installation Manual Full plug and play programming and power kit, for Ford Vehicles with 8" MyFord Touch Displays
Required for Install: 250-8420-MOD MyFord Touch Installation Manual Full plug and play programming and power kit, for Ford Vehicles with 8" MyFord Touch Displays 1. Ford Vehicle with 8" MyFord Touch Display
More informationINSTALLATION INSTRUCTIONS
Dual Camera Interface for Ford MyTouch 8 Display Screen (Kit # 9002-2781) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Interface
More informationMyTouch FIM LOCKPICK INSTALLATION OPTIONS COPYRIGHT 2013 COASTAL ELECTRONIC TECHNOLOGIES, INC.
AFTERMARKET REVERSE CAM VIDEO INPUT UNPLUG ORIGINAL SCREEN CONNECTOR THEN PLUG IN HERE PLUG AND PLAY NO OTHER CONNECTIONS ARE NECESSARY FOR OVERRIDE FEATURES AFTERMARKET REAR CAM CONNECT HERE CAM REAR
More informationINSTALLATION MANUAL Full plug and play programming and power kit, for Ford Vehicles with a camera-compatible 4 MyFord Display
ARC-MFCAM357 ARC-MFCAM357 INSTALLATION MANUAL Full plug and play programming and power kit, for Ford Vehicles with a camera-compatible 4 MyFord Display Required for Install: 1. Ford Vehicle with camera-compatible
More informationAX-ADDCAM AX-ADDCAM. INTERFACE COMPONENTS AX-ADDCAM interface AX-ADDCAM harness
AX-ADDCAM INSTALLATION INSTRUCTIONS AX-ADDCAM INTERFACE FEATURES (4) Camera inputs Programmable 12V 5-amp switched output (configured through the Axxess Updater program) Reverse signal trigger generated
More informationFord SYNC 3. Multi Camera Interface Installation and User Manual
250-8455 Ford SYNC 3 Multi Camera Interface Installation and User Manual Table Of Contents Installation 1 Switching to the Interface 3 Interface Homepage 4 Interface Settings 5 Camera Control 7 HDMI Input
More informationAX-AM-FD91. Ford (with Sync 3) HDMI and Camera Interface 2015-up*
AX-AM-FD91 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-FD91 interface AX-AM-FD91 harness LVDS (video) extension cable 6-pin to 4-pin LVDS (video) cable 10-pin harness with RCA jacks 3.5mm extension
More informationAX-AM-AU94. Audi Q5 (8R) (with Concert Radio) HDMI and Camera Interface
AX-AM-AU94 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-AU94 interface AX-AM-AU94 harness 10-pin harness with RCA jacks 10-pin T harness 20-pin T harness Audi Q5 (8R) (with Concert Radio) HDMI
More informationBMW09N-DYNAMIC Kit NTV-KIT725 Screen Connector
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW09N-DYNAMIC Kit NTV-KIT725 Screen Connector Overview The BMW09-N kit interfaces 2 video inputs
More informationC.O.D-F50. Ford OEM 360 Surround-View Camera Controller NTV-KIT899 BHM 02/01/19 NTV-DOC334
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 C.O.D-F50 Ford OEM 360 Surround-View Camera Controller NTV-KIT899 Overview The COD-F50 (Camera-On-Demand) kit allows Ford SuperDuty
More information3950 NW 120 th Ave, Coral Springs, FL TEL FAX MFT F-CAM. Force Front Camera Module NTV-KIT831 BHM 07/31/18 NTV-DOC298
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 MFT F-CAM Force Front Camera Module NTV-KIT831 BHM 07/31/18 Overview The MFT F-CAM module uses OEM buttons (or wire triggers)
More informationAX-AM-MB92. Mercedes Benz (NTG 5.0 with 7 or 8 display) HDMI and Camera Interface 2014-up*
AX-AM-MB92 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-MB92 interface AX-AM-MB92 harness 6-pin to 4-pin LVDS (video) cable LVDS extension cable 10-pin harness with RCA jacks 3.5mm extension cable
More informationAX-AM-AU95. Audi A1 (Typ 8X)(with Concert Radio) HDMI and Camera Interface 2010-up*
AX-AM-AU95 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-AU95 interface AX-AM-AU95 harness (new style) AX-AM-AU95 harness (old style) 20-pin T harness 6-pin to 4-pin LVDS (video) cable 10-pin harness
More informationPCM4-CAM NTV-KIT750. Overview
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com PCM4-CAM NTV-KIT750 Overview The PCM4-CAM Kit interfaces a backup camera input (with active
More informationAX-AM-BM91. BMW (with NBT 6.5 / 8.4 / control display*) HDMI and Camera Interface * For LVDS HSD+2-pin connector only
AX-AM-BM91 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-BM91 interface AX-AM-BM91 harness 6-pin to 4-pin LVDS (video) cable 10-pin harness with RCA jacks 3.5mm extension cable BMW (with NBT 6.5
More informationGM-K PRG. Dual Camera interface for 15 Chevy Sonic/Spark/Trax NTV-KIT626 BHM 10/15/15 NTV-DOC235
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 GM-K PRG Dual Camera interface for 15 Chevy Sonic/Spark/Trax NTV-KIT626 BHM Overview The GM-K PRG interfaces a reverse and
More informationFord 4 MULTI-CAM V1/V2 5-camera / AUX Video Interface for Ford 4 media screens NTV-KIT601/609
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 Ford 4 MULTI-CAM V1/V2 5-camera / AUX Video Interface for Ford 4 media screens NTV-KIT601/609 BHM Overview The Ford 4 MULTI-CAM
More informationInstallation Instructions ROSTRA. Select GM Vehicles with 7 Screens
Rostra 12-Volt Accessories Reverse Camera Input Interface for General Motors Vehicles 250-8454 Installation Instructions Select GM Vehicles with 7 Screens This manual shows a typical installation. Your
More informationBMW-EVO KIT NTV-KIT804
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW-EVO KIT NTV-KIT804 Screen Connector Overview The BMW-EVO kit interfaces 2 video inputs (including
More informationBMW / Mini. X SERIES Up X1 Sports Vehicle X5 Sports Activity Vehicle X6 Sports Activity Coupe
BMW / Mini 1 SERIES 2007-2011 1 Series 3-door hatchback 2007-2013 1 Series 2-door Coupe (1M) 2004-2012 1 Series (5-door) 2008 - Up 1 Series Convertible 3 SERIES 2005-2011 3 Series Sedan 2005-2011 3 Series
More informationBMW12N-DYNAMIC KIT NTV-KIT717
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW12N-DYNAMIC KIT NTV-KIT717 Screen Connector Overview The BMW12-N kit interfaces 2 video inputs
More informationAX-AM-AU91. Audi HDMI and Camera Interface 2013-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
AX-AM-AU91 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-AU91 interface AX-AM-AU91 harness 10-pin harness with RCA jacks 6-pin to 4-pin LVDS (video) cable Audi HDMI and Camera Interface 2013-up*
More informationGEN 6 LOCKPICK INSTALLATION OPTIONS COPYRIGHT 2010 COASTAL ELECTRONIC TECHNOLOGIES, INC.
AFTERMARKET FRONT/BABY CAMERA VIDEO CONNECT HERE FRONT/BABY CAM POWER TO LOCKPICK RED W/BLACK STRIPE WIRE TO LOCKPICK BLACK GROUND WIRE UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE PLUG AND PLAY
More informationW205-N RVC NTV-KIT703
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W205-N RVC NTV-KIT703 Overview The W205-N RVC Kit interfaces a backup camera input (with active
More informationTM C8 LOCKPICK PRO STEERING WHEEL CONTROLS * OPERATIONS WHILE MENUS ARE DISPLAYED ON INSTRUMENT CLUSTER CONTROLS ON BACK OF STEERING WHEEL BACK
TM C8 LOCKPICK PRO STEERG WHEEL CONTROLS SCROLL UP MENUS SELECT DESIRED FEATURE * OPERATIONS WHILE MENUS ARE DISPLAYED ON STRUMENT CLUSTER CONTROLS ON BACK OF STEERG WHEEL SCROLL DOWN MENUS TOGGLE TO REAR
More informationAX-AM-MB91. Mercedes Benz (NTG 4.5 with 5.8 & 7 display) HDMI and Camera Interface 2011-up*
AX-AM-MB91 INSTALLATION INSTRUCTIONS Mercedes Benz (NTG 4.5 with 5.8 & 7 display) HDMI and Camera Interface 2011-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications. INTERFACE
More informationW204-N RVC NTV-KIT704
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W204-N RVC NTV-KIT704 Overview The W204-N RVC Kit interfaces a backup camera input (with active
More informationINSTALLATION INSTRUCTIONS
Dual Camera Interface for Chrysler, Dodge, Jeep (Kit # 9002-2783 v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Factory T-harness
More informationGM2 FIM LOCKPICK INSTALLATION OPTIONS COPYRIGHT 2012 COASTAL ELECTRONIC TECHNOLOGIES, INC.
UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE PLUG AND PLAY NO OTHER CONNECTIONS ARE NECESSARY FOR OVERRIDE FEATURES CONNECT USB CABLE HERE FOR FUTURE UPDATES OPTIONAL POWER OUTPUTS FOR CAMERA(S)
More informationVolkswagen (with MIB platform) HDMI and Camera Interface 2014-up* Polo (Typ 6C) (b) Touran (Typ 5T) (b) (e)
AX-AM-VW91 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-VW91 interface AX-AM-VW91 harness 6-pin to 4-pin LVDS (video) cable 10-pin harness with RCA jacks Volkswagen (with MIB platform) HDMI and
More informationTM LOCKPICK C8 INSTALLATION OPTIONS COPYRIGHT 2011 COASTAL ELECTRONIC TECHNOLOGIES, INC. UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE
TM LOCKPICK C8 INSTALLATION OPTIONS COPYRIGHT 2011 COASTAL ELECTRONIC TECHNOLOGIES, INC. FACTORY CONNECTORS INCLUDED UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE PLUG AND PLAY NO OTHER CONNECTIONS
More informationIntroduction & Features. Important Notes. Installation Steps
Navigation Unlock & Reverse Camera Input Interface for Chrysler/Dodge/Jeep/Ram Vehicles Rev. 051915 ***Only applicable to revision 1.1.2 firmware on BCI-CH21*** Class 2 J1850 VPW Arbitration J1850 Class
More informationIOB-RVC NTV-KIT798. Overview
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com IOB-RVC NTV-KIT798 Overview The IOB-RVC interfaces a single backup camera input to the factory
More informationFDS3NAV2. For Ford Vehicles Equipped With SYNC3. Installation Instructions. Calibration and Setup Guide. Page 1 of 14
FDS3NAV2 For Ford Vehicles Equipped With SYNC3 Installation Instructions Calibration and Setup Guide Page 1 of 14 Please read this manual thoroughly before installation. This manual illustrates a typical
More informationBMW-EVO ID6 NTV-KIT837
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW-EVO ID6 NTV-KIT837 Screen Connector Overview The BMW-EVO ID6 kit interfaces 2 video inputs
More informationAudi (with MMI radio*) HDMI and Camera Interface * For vehicles with: 3 Basic 6.5-inch screen, 3G/3G+ 7-inch screen
AX-AM-AU96 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-AM-AU96 interface AX-AM-AU96 harness (new style) AX-AM-AU96 harness (old style) Audi (with MMI radio*) HDMI and Camera Interface 2008-2012 *
More informationUCTv2-W. 18 Wrangler uconnect 4.0 (CarPlay/Android Auto) Dual Camera Interface NTV-KIT851 BHM 01/19/18 NTV-DOC308
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 UCTv2-W 18 Wrangler uconnect 4.0 (CarPlay/Android Auto) Dual Camera Interface NTV-KIT851 BHM Overview The UCTv2-W interface
More informationADDITIONAL CAM POWER REVERSE CAM POWER BLUETOOTH MUTE AUDIO + IN AUDIO - IN 12V ACC OUTPUT 12V CONSTANT GROUND
UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE PLUG AND PLAY NO OTHER CONNECTIONS ARE NECESSARY USE HANDSFREE KIT MICROPHONE IPOD/IPHONE/ITOUCH/IPAD CONNECTION USB INPUT ADD YOUR BLUETOOTH HANDSFREE
More informationIOB-RVC NTV-KIT798. Overview
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com IOB-RVC NTV-KIT798 Overview The IOB-RVC interfaces a single backup camera input to the factory
More informationSIR-PCM3 955/997 SIRIUS Satellite Radio interface for Porsche PCM 3 radios NTV-KIT266/285
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 SIR-PCM3 955/997 SIRIUS Satellite Radio interface for Porsche PCM 3 radios NTV-KIT266/285 BHM Overview The SIR-PCM3 adds Sirius
More informationSMM501/501-H (Surveillance Mode Module) Ford Police Interceptors (Sedan and SUV)
An ISO 9001:2008 Registered Company SMM501/501-H (Surveillance Mode Module) 2013-2014 Ford Police Interceptors (Sedan and SUV) Introduction The SMM501/501-H is intended for 2013 and 2014 Ford Police Interceptors
More informationW205-RVC NTV-KIT580. Overview
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W205-RVC NTV-KIT580 Overview The W205-RVC Kit allows the user to add a backup camera input (with
More informationAUDI DYNAMIC-A3 NTV-KIT702
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com AUDI DYNAMIC-A3 NTV-KIT702 Overview The AUDI DYNAMIC-A3 Kit interfaces a backup camera input
More informationW204-H NTV-KIT794. Overview
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W204-H NTV-KIT794 Overview The W204-H RVC Kit interfaces two camera inputs and optional HDMI
More informationBMW12-DYNAMIC KIT NTV-KIT462
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW12-DYNAMIC KIT NTV-KIT462 Overview The BMW12 kit allows the user to add up to 3 video inputs
More informationGMNAV1 Advent Integrated Navigation
GMNAV1 Advent Integrated Navigation This interface is designed to integrate Navigation into select Buick and Chevrolet Systems. INSTALLATION MANUAL What s in the Box The following items are supplied with
More informationMULTIMEDIA & REAR-VIEW CAMERA INTEGRATION FOR SELECT LAND ROVER VEHICLES 2012-UP
LAND ROVER 2012-2015 LR2 2012-2015 LR4 2015-2015 New Discovery Sport 2012-2015 Range Rover Evoque 2012-2015 Range Rover Sport APPLICATION NOTES: THIS TERFACE REQUIRES THE VEHICLES TO HAVE A FACTORY AUX
More informationINSTALLATION INSTRUCTIONS
GM MyLink Camera Interface for 7-inch IOB Display Radios 2016 to Current (Kit # 9002-2765) ***NOTE: VERIFY YOU HAVE AN IOB RPO CODE located on the OEM RPO sticker (glove box or spare tire well). If the
More informationCamera Interface System User Quick Start Guide
Camera Interface System User Quick Start Guide We hope you enjoy the Rearsight Camera Interface. This system adds safety and functionality to your vehicle and brings the latest in technology to you. This
More informationTE-FORD-SV-1. TABLE OF CONTENTS Camera Installation App Configuration...6 Camera Specifications... 7
TE-FORD-SV-1 INSTALLATION INSTRUCTIONS Ford F-150 Side View Camera Kit 2015-2017 Visit ibeamusa.com for more detailed information about the product and up-to-date vehicle specific applications TABLE OF
More informationREAR-VIEW CAMERA & AV INPUT INTEGRATION INTERFACE FOR DODGE & JEEP VEHICLES 2014-UP
DODGE 2014-2015 Durango 2014-2015 RAM* JEEP 2014-2015 Grand Cherokee APPLICATION NOTES: FOR UCONNECT 5 AND 8.4 DISPLAYS *NOTE: Not compatible with diesel powered trucks. PARTS INCLUDED (2) CH-75V CAN Interface
More informationW DYNAMIC Kit NTV-KIT461
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W204-12 DYNAMIC Kit NTV-KIT461 Overview The W204-12 DYNAMIC kit allows the user to add up to
More informationCHRY UNI-CAM v2. Chrysler/Dodge/Jeep uconnect (RA4/RA3/RA2) Dual Camera/Control in Motion Interface NTV-KIT759
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 CHRY UNI-CAM v2 Chrysler/Dodge/Jeep uconnect (RA4/RA3/RA2) Dual Camera/Control in Motion Interface NTV-KIT759 Compatible with
More informationAPVLR12. Rear View Camera Input and Video In Motion.
APVLR12 Rear View Camera Input and Video In Motion www.connects2.com ABOUT THIS PRODUCT... APVLR12 Reversing Camera Add-On and Video in Motion Interface for Land Rover touch screen navigation version 3
More informationCoastal Electronic Technologies, Inc. GM LOCKPICK GMX-320 Installation and Operation Instructions
Coastal Electronic Technologies, Inc. GM LOCKPICK GMX-320 Installation and Operation Instructions Thank you for your purchase of the Coastal Electronic Technologies, Inc. GM LOCKPICK GMX- 320. The GMX-320
More informationAUDI DYNAMIC-EXT NTV-KIT701
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com AUDI DYNAMIC-EXT NTV-KIT701 Overview The AUDI-DYN EXT Kit interfaces a backup camera (with dynamic
More informationTJ to 2006 Jeep Wrangler Installation Tips V1.0
TJ1002 2003 to 2006 Jeep Wrangler Installation Tips V1.0 Table of Contents I. Introduction II. Safety precautions III. Opening the dash IV. Removing the stock radio V. Installing the TJ1002 VI. Backup
More informationSYNC FIM LOCKPICK INSTALLATION OPTIONS COPYRIGHT 2014 COASTAL ELECTRONIC TECHNOLOGIES, INC.
UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE GPS ANTENNA OPTION INCLUDED CONNECT USB CABLE HERE FOR FUTURE UPDATES FACTORY CONNECTORS INCLUDED 2 VIDEO CABLE TYPES INCLUDED **SEE APPLICATION GUIDE**
More informationA3/GOLF 7-CAM NTV-KIT500
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com A3/GOLF 7-CAM NTV-KIT500 Overview The A3/GOLF7-CAM Kit allows the user to add 1 video input
More informationFord Vehicles equipped with MyFord Touch SYNC3 System Multi-Camera Interface
2016-2018 Ford Vehicles equipped with MyFord Touch SYNC3 System Multi-Camera Interface S1C067A-Y03E Installation and User Manual Disclaimer Please read this manual thoroughly prior to installation. This
More informationC2-MMI2G-x. Compatible with Audi MMI 2G navigation systems
c.logic Interface C2-MMI2G-x Compatible with Audi MMI 2G navigation systems Product features Full plug and play multimedia interface 2 AV-inputs with separate IR-control-channels Integrated into vehicle
More informationARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios.
Required for Install: ARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios. 1. Chrysler/Dodge/Jeep vehicle with Uconnect
More informationJaguar F-TYPE CAM Dual Camera interface for select 14+ Jaguar vehicles NTV-KIT589
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 Jaguar F-TYPE CAM Dual Camera interface for select 14+ Jaguar vehicles NTV-KIT589 BHM Overview Jaguar F-TYPE CAM interfaces
More informationCHRY MULTI-CAM. Dodge/Jeep uconnect (RA4) Interface with 6 video inputs NTV-KIT764 BHM 09/25/17 NTV-DOC266
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 CHRY MULTI-CAM Dodge/Jeep uconnect (RA4) Interface with 6 video inputs NTV-KIT764 BHM Overview The UCTv2 series Interface integrates
More informationAUDI DYNAMIC-EXT NTV-KIT701
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com AUDI DYNAMIC-EXT NTV-KIT701 Overview The AUDI-DYN EXT Kit interfaces a backup camera (with dynamic
More informationAUDI-09 EXT MMi NTV-KIT187
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com AUDI-09 EXT MMi NTV-KIT187 Overview The AUDI-09 EXT MMi Kit allows the user to add up to 3 video
More informationNTG3-SL NTV-KIT142. Overview Mercedes-SL. Backup camera / AV input / RSE / Video In Motion interface. Kit Contents. NTG3 Module NTV-ASY171
NTG3 5.04.14 NAV-TV 3950 NW 120 Ave, Coral Srings, FL NTV-KIT142 Overview 2009-2011 Mercedes-SL Backup camera / AV input / RSE / Video In Motion interface Kit Contents SMB to RCA NTV-CAB007 Plug & Play
More informationCI-C1-NTG25. for Mercedes Benz Comand APS NTG2.5 navigation systems
c.logic lite-interface for Mercedes Benz Comand APS NTG2.5 navigation systems Product features full plug and play multimedia interface 1 AV-input with separate IR-control channel control of after-market
More informationIntroduction and Features. Important Notes. Module Layout
Introduction and Features The interface allows the replacement of a factory radio in select General Motors vehicles with the Class II Data-Bus. Using this interface will retain factory features such as
More informationW204-5 NTV-KIT198. Overview
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W204-5 NTV-KIT198 Overview The W204-5 Kit allows the user to add up to 3 video inputs and a
More informationAP4-CH41. Amplifier Integration Interface for Chrysler / Dodge / Jeep / RAM. Introduction and Features. Important Notes. Wiring Connection Chart
Introduction and Features The AP4-CH41 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range, fixed level headunit output, in conjunction with CAN messages,
More informationCoastal Electronic Technologies, Inc. Chrysler/Dodge/Jeep FREEDOM IN MOTION MYGIG LOCKPICK Installation and Operation Instructions
Coastal Electronic Technologies, Inc. Chrysler/Dodge/Jeep FREEDOM IN MOTION MYGIG LOCKPICK Installation and Operation Instructions Thank you for your purchase of the Coastal Electronic Technologies, Inc.
More informationC1-C25. compatible with navigation systems Mercedes Benz Comand 2.5
c.logic lite-interface compatible with navigation systems Mercedes Benz Comand 2.5 Product features full plug and play multimedia interface 1 AV-input with separate IR-control channel control of after-market
More informationC1-MFD2. Compatible with navigation systems Volkswagen MFD2/RNS2 Skoda Nexus
c.logic lite-interface Compatible with navigation systems Volkswagen MFD2/RNS2 Skoda Nexus Only for vehicles WITHOUT factory rear-view camera Product features full plug and play multimedia interface 1
More informationSync KIT SYSTEM INSTALLATION
2008 Navigator, Navigator L Sync Kit Manual Table of Contents Sync KIT SYSTEM INSTALLATION CONTENTS INSTALLATION Sync Kit GENERAL PROCEDURES Configuration & Programming Functional Test Troubleshooting
More informationDODGE Challenger Charger Journey. 6-Pin Video Input Cable 6-Pin Audio In/Out Cable GPS Magnetic Antenna
CHRYSLER 2011-2014 300c DODGE 2011-2014 Challenger 2011-2014 Charger 2011-2014 Journey FIAT 2011-2014 Freemont Plug and Play connectors make installation simple and easy. Utilizes the latest mapping version
More informationJaguar F-TYPE CAM 16. Dual Camera interface for select 16+ Jaguar vehicles NTV-KIT746 BHM 05/31/16 NTV-DOC259
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 Jaguar F-TYPE CAM 16 Dual Camera interface for select 16+ Jaguar vehicles NTV-KIT746 BHM Overview Jaguar F-TYPE CAM 16 interfaces
More informationNNG-GM2 Navigation interface for GM vehicles equipped with LVDS MYLink/CUE NTV-KIT552
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-GM2 Navigation interface for GM vehicles equipped with LVDS MYLink/CUE NTV-KIT552 1. GM2 LVDS Interface/GPS combo 2. Plug
More informationC1-C20. Compatible with navigation systems Mercedes Benz Comand 2.0 Comand APS CD
c.logic lite-interface Compatible with navigation systems Mercedes Benz Comand 2.0 Comand APS CD Product features full plug and play multimedia interface 1 AV-input with separate IR-control channel control
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Chrysler/Dodge/Jeep Remote Add-On CD player for RA1, RA2, RA3, or RA4 radios (Kit # 5000-8750) 2013-current RAM truck and Viper; 2015-current Charger, Challenger, and 300; 2017 Pacifica Please read thoroughly
More informationZL-MYGIG500. Audio-video-input and rear-view camera input incl. video-in-motion for Chrysler, Dodge and Jeep vehicles with MYGIG navigation systems
z.link-interface Audio-video-input and rear-view camera input incl. video-in-motion for Chrysler, Dodge and Jeep vehicles with MYGIG navigation systems AV-input to connect any AV-source and a rear-view
More informationINSTALLATION AND USER MANUAL FOR GATEWAY PRO BT
INSTALLATION AND USER MANUAL FOR GATEWAY PRO BT 1. INTRODUCTION The Dension Gateway Pro BT lets you connect your ipod or USB storage (stick, hard drive or mass storage capable mp3 player) to your original
More informationC2-NTG25. Compatible with Mercedes Benz Comand APS NTG2.5 navigation systems
c.logic-interface Compatible with Mercedes Benz Comand APS NTG2.5 navigation systems Product features full plug and play multimedia interface 2 AV-inputs with separate IR-control channel control of after-market
More informationNTG3 / NTG3E /NTG3SLK NTV-KIT102/106/189. Overview up Mercedes GL/ML/R/E/CLS/SLK. Backup camera / AV input / RSE / Video In Motion interface
NTG3 5.04.14 NAV-TV 3950 NW 120 Ave, Coral Srings, FL NTG3 / NTG3E /NTG3SLK NTV-KIT102/106/189 Overview 2009-up Mercedes GL/ML/R/E/CLS/SLK Backup camera / AV input / RSE / Video In Motion interface Kit
More informationGM-PRO UNLOCK INSTALLATION OPTIONS 3 VIDEOS SOURCES - 3 AUDIO SOURCES
GM-PRO UNLOCK INSTALLATION OPTIONS 3 VIDEOS SOURCES - 3 AUDIO SOURCES USE HANDSFREE KIT MICROPHONE ** INCLUDED CONNECTION FOR AFTERMARKET REAR VIEW CAMERA VIDEO 3 INPUT OR USE RCA TO 1/8" ADAPTER FOR AUDIO
More informationNOTICE OF INTENDED INSTALLATION AND USE
* JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface. NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER,
More informationUSB-C25. compatible with navigation systems Mercedes Benz Comand 2.5
usblogic USB-AV-Player compatible with navigation systems Mercedes Benz Comand 2.5 Product features USB-port for media up to 2 TB (2000GB) supports FAT32 and NTFS formatted media multi partition capable
More informationVL2-CONCERT. for Audi with 6,5 monitor, Symphony or Concert radio
v.link Video-inserter for Audi with 6,5 monitor, Symphony or Concert radio Video-inserter with 2 video + RGB + rear-view camera input Product features Video-inserter for factory-infotainment monitors 2
More informationREC-AV XG NTV-KIT276
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com REC-AV XG NTV-KIT276 Overview The REC-AV XG adds video input (including rear camera) for select
More informationRFM-TYS Multi View Integration Interface with A/V Input and Side Mirror Mounted Cameras For Toyota Sienna 2018
INTEFACING SOLUTIONS FM-TYS PODUCT FEATUES: - Adds a reverse camera input, 6 video plus 1 audio/video inputs. - Uses the steering wheel controls buttons to toggle between the sources. - Turn signals automatically
More informationv.logic Intelligent Solution Interface V4-CCC
v.logic Intelligent Solution Interface For the E-series BMW and Mini with navigation system or radio and 6.5 or 8.8 monitor with 10pin BMW LVDS connector Product features Plug and play media-controller
More informationNOTICE OF INTENDED INSTALLATION AND USE
* JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface. NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER,
More informationMazda Connect Infotainment System
- The ACPMZ-72Z has a built in Dual-Link module that allows connection of Android and other devices with two-way mirroring control. - Adds a reverse camera input with active parking guidelines. - Adds
More informationv.logic Intelligent Solution Interface V5-CCC-PNP
v.logic Intelligent Solution Interface Compatible with E-series BMW and Mini with navigation system or radio and 6.5 or 8.8 monitor with 10pin BMW LVDS connector Product features Own on-screen display
More informationJailbreaker Enigma manual den 17 oktober 2018
This manual covers how to install the Jailbreaker Enigma and the supplied cable harness. This manual does not cover the installation of cameras or other video sources. First of all, please make sure that
More informationCar-solutions.com. Video Interface for BMW (V.1.1) Specification & Installation
Last updated : 2013.01.29 Model : QVI-BM12-Main-V1.0 IF / Product code : QVI-BM12-1112-002 Video Interface for BMW (V.1.1) Specification & Installation Contents 1. Before installation 1.1 Main specification
More informationCI-VL2-MBN45. for Mercedes Benz vehicles generation NTG with Comand Online, Audio50 APS or Audio 20 with 4pin HSD LVDS connector on the monitor
v.link Video-inserter CI-VL2-MBN45 for Mercedes Benz vehicles generation NTG4.5-204 with Comand Online, Audio50 APS or Audio 20 with 4pin HSD LVDS connector on the monitor Video-inserter with 2 video +
More information