TE-FORD-SV-1. TABLE OF CONTENTS Camera Installation App Configuration...6 Camera Specifications... 7

Transcription

1 TE-FORD-SV-1 INSTALLATION INSTRUCTIONS Ford F-150 Side View Camera Kit Visit ibeamusa.com for more detailed information about the product and up-to-date vehicle specific applications TABLE OF CONTENTS Camera Installation App Configuration...6 Camera Specifications... 7 TOOLS REQUIRED 7mm screwdriver Cutting tool File or roto tool Tape Pry tool KIT COMPONENTS A) Camera and wiring (2) B) Camera pods (2) C) AX-ADDCAM and harnessing A B C Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition. ibeam Vehicle Safety Systems ibeamusa.com COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 2/26/19 INSTTE-FORD-SV-1

2 CAMERA INSTALLATION Radio removal: 1. Remove the panel highlighted from the pocket area (Figure A) 2. Remove (2) 7mm screws exposed within the cavities forward of the center channel speaker. (Figure B) 3. Pop up the pocket panel and remove (2) 7mm screws from the top of the front facing radio panel. (Figure C) 4. Remove (2) 7mm screws securing the screen. (Figure D) Note: 4.2 screens have 4 screws; 8 screens have 6 screws screen models use a 12-pin connector; 8 screen models a 52-pin connector. Locate the appropriate connector provided with the kit and disregard the other. (Figure A) (Figure C) Continued on the next page (Figure B) (Figure D) ibeamusa.com

3 CAMERA INSTALLATION (CONT.) Door panel removal: 6. There are (7) 7mm screws to remove the door panel. (Figure E) 7. It is suggested for the speaker be removed to provide easier access to run the wiring into the vehicle. There are (4) 7mm screws to remove the speaker. (Figure F) 8. Remove the mirror cover, this is where the provided camera pod will be placed. (Figure G) Installation: 9. Run the camera wire into the pod, and run the wire in thru the mirror into the door panel. There is some foam in the mirror that will need to be either removed or cut out to gain access to the door panel. It is suggested to cut a hole on the inside of the door panel foam to gain access. (Figure H) Continued on the next page (Figure E) (Figure G) (Figure F) (Figure H) REV. 2/26/2019 INSTTE-FORD-SV-1 3

4 CAMERA INSTALLATION (CONT.) 10. After the wire from the camera is ran into the interior of the door panel, follow the route that is shown in the picture below. Cut a small hole or slit in the cover that is also shown in the picture below, indicated by a circle. This will allow easier access to the boot of the door. (Figure I) 11. Pop off the rubber cover from the boot in the door jamb to gain access to the connector inside. There are (2) clips located at the top and bottom of the connector for removal. Remove the connector from the truck, then unplug the (2) connectors within the connector. (Figure J) 12. Once the wire is ran through the boot, the connector will need to be modified to allow the camera cable through. Care must be taken so that the connector and rubber boot will stay intact to ensure that the connector remains water resistant like factory. Reference the highlighted area below. This is where a channel will need to be made to allow the camera cable through. It is suggested for this be carefully done with a either a file or a roto tool. Placing a piece of tape over the wire while pushing the connector back into the vehicle is also suggested to avoid it from coming loose and getting jammed up during the reconnection process. (Figures K & L) Continued on the next page (Figure I) (Figure K) (Figure J) (Figure L) ibeamusa.com

5 CAMERA INSTALLATION (CONT.) 13. After the boot is back in place and the connectors are plugged back into the connector, run the camera cable to the radio opening. Duplicate the same process for the opposite door. Attention! If the vehicle is equipped with a 4.2 radio display screen, the following (4) steps will need to be performed to retain the signal from the turn signal indicators. If the vehicle is equipped with an 8 screen, skip to step Remove the bottom of the steering column by prying up the upper steering column with a pry tool. (Figure M) 15. Remove three 7mm screws from the bottom of the steering column cover. (Figure M) 16. The turn signal connector is located on the passenger side of the steering column, towards the steering wheel. (Figure N) 17. Disconnect the 12-pin gray connector, then plug in the LD-STALK-FD1. Run both the Blue and Blue/Red wires to the radio location. (Figure M) (Figure N) 18. Once the wires are at the radio location, connect the appropriate T-harnesses provided with the kit. 4.2 screen models will use the 12-pin T-harness; 8 screen models will use the 52-pin T-harness. For the 4.2 screen models, the Blue and Blue/Red wires from the previous steps will need to be connected by butt connectors that come preinstalled on the harness. 19. Take the female RCA from the T-harness and connect it to the male RCA from the AX-ADDCAM harness labeled Camera output. 20. If the vehicle is equipped with a factory camera, take the male RCA from the T-harness and connect it to the female RCA from the AX-ADDCAM harness labeled Camera Connect the RCA s from the side cameras to the female RCA s from the AX-ADDCAM harness labeled Camera 2 and Camera 3. Remember which side was plugged into which camera input. This is important when programming the interface. 22. Ground the Black wire from the cameras to chassis ground. 23. Connect the Red wire from the cameras to the red wire from the AX-ADDCAM labeled Camera 12V. REV. 2/26/2019 INSTTE-FORD-SV-1 5

6 APP CONFIGURATION 1. Download and install the Axxess Updater from www. axxessinterfaces.com. Open the app, then select Add-Cam Configuration. (Figure A) 2. Select the year and screen size of the vehicle from the drop down menus, then click the Configuration tab at the top. (Figure B) Note: The Configuration tab will be shown once the vehicle is selected. 3. Assign the camera inputs as they were wired in the vehicle. (Figure C) 4. The trigger assignments should be: Reverse, Left and Right. 5. If the cameras are wired to the red 12V Camera Power wire from the AX-ADDCAM: From within the Other Settings section, use the dropdown menu to change switched 12V with Camera Active 6. If the vehicle did NOT have an OEM Reverse camera, place a check mark in the OEM programming selection in Other Settings. 7. If the vehicle did have an OEM Reverse camera, no further programming is needed. 8. Click Write to Configuration, then plug the interface into the T-harness. (Figure A) (Figure C) (Figure B) ibeamusa.com

7 CAMERA SPECIFICATIONS Sensor CMOS 7080 Resolution 480 TV Lines Field of view Diagonal 170º, Horizontal 110º, Vertical 90º Illumination 0.6 Lux IP rating IP67 Parking Lines None Extension cable 26 TV system NTSC Working Temp -20ºC ~ 70ºC Warranty 3 years REV. 2/26/2019 INSTTE-FORD-SV-1 7

8 TE-FORD-SV-1 INSTALLATION INSTRUCTIONS If you are having difficulties with the installation of this product, please call our Tech Support line either by phone at TECH, or at Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians ibeam Vehicle Safety Systems ibeamusa.com COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 2/26/19 INSTTE-FORD-SV-1