IDM+/Informa TWS-FL and iq+

Transcription

1 Qualitrol training brochure IDM+/Informa TWS-FL and iq Training catalog_rev01

2 IDM+/Informa Installation and Commissioning training number of participant. This four-day course for up to eight (8) students prepares maintenance and engineering personnel to install, test, configure, and operate the Qualitrol IDM+ Digital Fault Recorder and Informa Power Quality Recorder. Special emphasis is placed on achieving performance based objectives which include all the critical tasks required to set up, configure, commission and perform some basic operation on the system. Introduction Architecture of device vs schematics Time synchronization Communication Interfaces Web pages Day 4 Device recovery Jumper settings configuration Firmware upgrade Calibration of analog inputs Data in device iq+ installation Overview of different typed of recording Configuration of IDM+/Informa for Site Acceptance Test Inject input signals Retrieve and analyse data Validation of data Introduction to data analyst training Personnel who will install, maintain the IDM+/Informa system including installation, interconnection, calibration and basic configuration of the system. IDM+/Informa training system (optional) Calibration source for each training system Doble, OMICRON, ISA or equivalent.

3 Data Analyst training (Theoretical and practical) number of participant. This three-day course for up to eight (8) students prepares operations personnel to configure, and operate any Qualitrol Digital Fault Recorder/Power Quality Recorder and iq+ software. Special emphasis is placed on achieving performance based objectives which include all the critical tasks required to set up, configure and operate the system. Introduction Hardware and webpages overview Explanation of wiring Data in device through: COMTRADE Modbus PMU IEC61850 Deleting data from device Firmware upgrade iq+ deployments Configuration of device according to customer requirement Collect data Analysis of data including Traveling wave analysis Record Analysis iq+ notifications Housekeeping of iq+ data Personnel who will operate and analyse data from the IDM+ Fault recorder/informa Power Quality system including reporting, exporting data and configuration of the system. IDM+/Informa training system (optional) Calibration source for each training system would be appreciated Doble, OMICRON, ISA or equivalent.

4 TWS-FL Installation/Commissioning and Data Analyst training number of participant. This three-day course for up to eight (8) students prepares maintenance and operations personnel to install, test, configure and operate any Qualitrol Fault Locator and iq+ software. Special emphasis is placed on achieving performance based objectives which include all the critical tasks required to set up, commission, configure and operate the system. Basic of traveling wave Architecture of device vs schematics Time synchronisation Communication Interfaces Web pages Deleting data from device Firmware upgrade and device recovery iq+ installation/deployments TWS-FL project management: Breaker schemes Installation of linear couplers Measurement from CVT and bushing coupler Configuration of device according to customer requirement Data in device through IEC61850 Inject input signals Collect data Traveling wave data analysis iq+ notifications Housekeeping of iq+ data Personnel who will install, operate and analyse data from Fault Locators system including installation, configuration (hardware and software) and reporting of the system. TWS-FL training system (optional) Pulse generator for each training system would be appreciated.

5 IDM+/TWS-FL and iq+ training Benefits Educational Services Benefits (Onsite and factory Training) Less talk more action More action - all our courses focus on the practical side of the product. When your engineer or technician attends our courses, they will know how to configure the product to suit your particular needs and requirements. Why, because all courses are centered around hands-on experience. Certified instructors All QUALITROL instructors have been certified as experts in their product area. To become an expert, an instructor must successfully complete the QUALITROL product certification program designed around the particular product and have at least two years product experience. This is our guarantee that each instructor is fully technically qualified. To guarantee that our instructors are armed with the latest presentation skills, each instructor is specifically trained in course presentation methodologies. Professionally developed courses All courses are designed by professionals who have many years of field commissioning experience coupled with field proven learning methods. Our course designers have been there, in the field, with you, and know what must be learned and understood to ensure complete and practical product knowledge and capability. We can bring the classroom to you We bring factory training to your location. Because our courses are designed so tightly around hands-on training, QUALITROL can supply all the equipment assuring that each student gains the experience of equipment installation, configuration, calibration, and troubleshooting. Educated customers It is our philosophy that an educated customer is a long term customer. Our goal is to provide our customers the sense of security that comes from knowing that their personnel have full product understanding.