Command Manual QinQ-BPDU TUNNEL H3C S5500-SI Series Ethernet Switches. Table of Contents
|
|
- Curtis Caldwell
- 5 years ago
- Views:
Transcription
1 Table of Contents Table of Contents QinQ Configuration Commands qinq enable qinq ethernet-type qinq vid raw-vlan-id inbound Chapter 2 BPDU Tunnel Configuration Commands BPDU Tunnel Configuration Commands bpdu-tunnel dot1q enable bpdu-tunnel dot1q stp i
2 1.1 QinQ Configuration Commands qinq enable Syntax qinq enable undo qinq enable Ethernet port view, port group view None Use the qinq enable command to enable basic QinQ for the current Ethernet port. Use the undo qinq enable command to disable basic QinQ for the current Ethernet port. By default, basic QinQ is disabled on an Ethernet port. After basic QinQ is enabled on the port, frames on this port will be tagged with a new VLAN tag, the VLAN ID in which is the default VLAN ID of the port. Configured in Ethernet port view, the setting is effective on the current port only; configured in port group view, the setting is effective on all ports in the port group. # Enable basic QinQ for GigabitEthernet 1/0/1. [Sysname] interface GigabitEthernet 1/0/1 [Sysname-GigabitEthernet1/0/1] qinq enable # Enable basic QinQ for all the ports in port group 1. [Sysname] port-group manual 1 [Sysname-port-group-manual-1] qinq enable 1-1
3 1.1.2 qinq ethernet-type Syntax qinq ethernet-type hex-value undo qinq ethernet-type System view hex-value: Hexadecimal protocol type ID, in the range of 1 to FFFF. Use the qinq ethernet-type command to configure a global QinQ TPID value. Use the undo qinq ethernet-type command to restore the default. By default, the QinQ TPID is 0x8100. # Set the global TPID value to 0x8200. [Sysname] qinq ethernet-type qinq vid Syntax qinq vid vlan-id undo qinq vid vlan-id Ethernet port view, port group view vlan-id: Outer VLAN ID, in the range 1 to Use the qinq vid command to enter QinQ view and configure the outer VLAN tag to be added to BPDUs. Use the undo qinq vid command to remove all configurations corresponding to the VLAN ID performed in QinQ view. 1-2
4 By default, the outer VLAN tag is the VLAN tag corresponding to the port s default VLAN ID. Configured in Ethernet interface view, the setting is effective on the current port only; configured in port group view, the setting is effective on all ports in the port group. This command must be coupled with the raw-vlan-id inbound command to add different outer VLAN tags for frames of different VLANs. Related command: raw-vlan-id inbound. # Configure GigabitEthernet1/0/1 to tag frames with outer VLAN tag of VLAN 10. [Sysname] interface GigabitEthernet 1/0/1 [Sysname-GigabitEthernet1/0/1] qinq vid 10 [Sysname-GigabitEthernet1/0/1-vid-10] # Configure all the ports in port group 1 to tag frames with outer VLAN tag of VLAN 10. [Sysname] port-group manual 1 [Sysname-port-group-manual-1] qinq vid 10 [Sysname-port-group-manual-1-vid-10] raw-vlan-id inbound Syntax raw-vlan-id inbound { all vlan-id-list } undo raw-vlan-id inbound { all vlan-id-list } QinQ view vlan-id-list: A set of VLAN IDs, defined the form of vlan-id-list = { vlan-id [ to vlan-id ] }&<1-10>, where the VLAN ID after the to keyword must be larger than or equal to the VLAN ID before the to keyword, and &<1-10> means that you can specify up to 10 VLANs or VLAN ranges for this argument. all: Specifies all VLAN IDs. Use the raw-vlan-id inbound command to add the current outer VLAN tag for the specified inner VLAN IDs. 1-3
5 Use the undo raw-vlan-id inbound command to remove the configuration. Caution: A frame cannot be tagged with different outer VLAN tags at the same time. If you want to change an outer VLAN tag, you must delete the old outer VLAN tag configuration and configure a new outer VLAN tag. Related command: qinq vid. # Configure GigabitEthernet1/0/6 to tag frames of VLAN3, VLAN5, and VLAN 20 through VLAN 100 with the outer VLAN tag of VLAN 100. [Sysname] interface GigabitEthernet 1/0/6 [Sysname-GigabitEthernet1/0/6] qinq vid 100 [Sysname-GigabitEthernet1/0/6-vid-100] raw-vlan-id inbound to
6 Chapter 2 BPDU Tunnel Configuration Commands Chapter 2 BPDU Tunnel Configuration Commands 2.1 BPDU Tunnel Configuration Commands bpdu-tunnel dot1q enable Command bpdu-tunnel dot1q enable undo bpdu-tunnel dot1q enable System view, Ethernet port view, port group view None Use the bpdu-tunnel dot1q enable command to enable BPDU tunnel. Use the undo bpdu-tunnel dot1q enable command to disable BPDU tunnel. Configured in system view, the command enables or disables BPDU tunnel globally; configured in Ethernet port view, the setting is effective on the current port only; configured in interface view, the command enables or disables BPDU tunnel on the current port only; configured in port group view, the command enables or disables BPDU tunnel on all ports in the port group. By default, BPDU tunnel is enabled globally but disabled for all ports. 2-1
7 Chapter 2 BPDU Tunnel Configuration Commands Note: BPDU tunnel must be enabled globally before the BPDU tunnel configuration for a port can take effect. For an Ethernet port, as STP is incompatible with STP BPDU tunnel, the two features cannot be enabled at the same time. Before enabling STP BPDU tunnel for a port, make sure STP is not enabled on the port. For an Ethernet port, as the BPDU tunnel feature is incompatible with GVRP, the two features cannot be enabled at the same time. Before enabling BPDU tunnel for a port, make sure GVRP is not enabled on the port. For an Ethernet port, as the BPDU tunnel feature is incompatible with NTDP, the two features cannot be enabled at the same time. Before enabling BPDU tunnel for a port, make sure NTDP is not enabled on the port (you can use the undo ntdp enable command to disable NTDP). For information about NTDP, refer to the Cluster part in this manual. # Enable BPDU tunnel globally. [Sysname] bpdu-tunnel dot1q enable # Enable BPDU tunnel for GigabitEthernet1/0/1. [Sysname] interface GigabitEthernet 1/0/1 [Sysname-GigabitEthernet1/0/1] bpdu-tunnel dot1q enable # Enable BPDU tunnel for all the ports in the port group 1. [Sysname] port-group manual 1 [Sysname-port-group-manual-1] bpdu-tunnel dot1q enable bpdu-tunnel dot1q stp Command bpdu-tunnel dot1q stp undo bpdu-tunnel dot1q stp Ethernet port view, port group view 2-2
8 Chapter 2 BPDU Tunnel Configuration Commands None Use the bpdu-tunnel dot1q stp command to enable STP BPDU tunnel for a port or a group of ports. Use the undo bpdu-tunnel dot1q stp command to disable STP BPDU tunnel for a port or a group of ports. By default, the STP BPDU tunnel feature is disabled for all ports. Configured in Ethernet port view, the setting is effective on the current port only; configured in port group view, the setting is effective on all ports in the port group. Relative command: bpdu-tunnel dot1q enable. # Enable STP BPDU tunnel for GigabitEthernet1/0/1. [Sysname] interface GigabitEthernet 1/0/1 [Sysname-GigabitEthernet1/0/1] stp disable [Sysname-GigabitEthernet1/0/1] bpdu-tunnel dot1q stp # Enable STP BPDU tunnel for all the ports of the port group 1. [Sysname] port-group manual 1 [Sysname-port-group-manual-1] bpdu-tunnel dot1q stp 2-3
Command Manual QinQ-BPDU Tunneling H3C S3610&S5510 Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 QinQ Configuration Commands... 1-1 1.1.1 mac-mirroring... 1-1 1.1.2 raw-vlan-id inbound... 1-2 1.1.3 qinq enable... 1-3 1.1.4 qinq ethernet-type... 1-4 1.1.5
More informationCommand Manual (For Soliton) VLAN-VPN. Table of Contents
Table of Contents Table of Contents Chapter 1 VLAN-VPN Configuration Commands... 1-1 1.1 VLAN-VPN Configuration Commands... 1-1 1.1.1 display port vlan-vpn... 1-1 1.1.2 vlan-vpn enable... 1-2 1.1.3 vlan-vpn
More informationTable of Contents 1 QinQ Configuration BPDU Tunneling Configuration 2-1
Table of Contents 1 QinQ Configuration 1-1 Introduction to QinQ 1-1 Understanding QinQ 1-1 Implementations of QinQ 1-2 Modification of TPID Value of QinQ Frames 1-3 Configuring Basic QinQ 1-4 Configuring
More informationLoop detection commands 1
Contents Loop detection commands 1 display loopback-detection 1 loopback-detection action 1 loopback-detection enable 2 loopback-detection global action 3 loopback-detection global enable 4 loopback-detection
More informationConfiguring BPDU tunneling
Contents Configuring BPDU tunneling 1 Introduction to BPDU tunneling 1 Background 1 BPDU Tunneling implementation 2 Configuring BPDU tunneling 3 Configuration prerequisites 3 Enabling BPDU tunneling for
More informationLoopback detection configuration commands
Contents Loopback detection configuration commands 1 display loopback-detection 1 loopback-detection action 2 loopback-detection enable 2 loopback-detection interval-time 3 i Loopback detection configuration
More informationHuawei H HCNP R&S Fast Track.
Huawei H12-224 HCNP R&S Fast Track http://killexams.com/pass4sure/exam-detail/h12-224 Question: 591 Which statements about the MUX VLAN configuration are true? (Select 2 Answers) [Quidway]vlan 10 [Quidway-vlan10]mux-vlan
More informationConfiguring IEEE 802.1Q and Layer 2 Protocol Tunneling
CHAPTER 8 Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling Virtual private networks (VPNs) provide enterprise-scale connectivity on a shared infrastructure, often Ethernet-based, with the same security,
More informationConfiguring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling
9 CHAPTER Configuring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling Virtual private networks (VPNs) provide enterprise-scale connectivity on a shared infrastructure, often Ethernet-based, with the
More informationCommand Manual MAC Address Table Management H3C S5500-EI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 MAC Address Table Management... 1-1 1.1.1 display mac-address... 1-1 1.1.2 display mac-address aging-time... 1-2 1.1.3 mac-address (Ethernet port view)...
More informationTable of Contents 1 VLAN Configuration 1-1
Table of Contents 1 VLAN Configuration 1-1 Overview 1-1 Introduction to VLAN 1-1 VLAN Fundamentals 1-2 Types of VLAN 1-3 Introduction to Port-Based VLAN 1-3 Configuring a VLAN 1-4 Configuration Task List
More informationTable of Contents 1 QinQ Configuration 1-1
Table of Contents 1 QinQ Configuration 1-1 Introduction to QinQ 1-1 Background 1-1 QinQ Mechanism and Benefits 1-1 QinQ Frame Structure 1-2 Implementations of QinQ 1-3 Modification of the TPID Value in
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5101 Document version: 6W100-20111031 Copyright 2011,
More informationHP A3100 v2 Switch Series
HP A3100 v2 Switch Series Layer 2 - LAN Switching Command Reference HP A3100-8 v2 SI Switch (JG221A) HP A3100-16 v2 SI Switch (JG222A) HP A3100-24 v2 SI Switch (JG223A) HP A3100-8 v2 EI Switch (JD318B)
More informationConfiguring Q-in-Q VLAN Tunnels
Information About Q-in-Q Tunnels, page 1 Licensing Requirements for Interfaces, page 7 Guidelines and Limitations, page 7 Configuring Q-in-Q Tunnels and Layer 2 Protocol Tunneling, page 8 Configuring Q-in-Q
More informationConfiguring IEEE 802.1Q Tunneling
CHAPTER 26 This chapter describes how to configure IEEE 802.1Q tunneling in Cisco IOS Release 12.2SX. For complete syntax and usage information for the commands used in this chapter, see the Cisco IOS
More informationHP 6125G & 6125G/XG Blade Switches
HP 6125G & 6125G/XG Blade Switches Layer 2 - LAN Switching Configuration Guide Part number:5998-3155a Software version: Release 2103 and later Document version: 6W102-20141218 Legal and notice information
More informationConfiguring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling
CHAPTER 14 Configuring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling With Release 12.1(13)E and later, the Catalyst 6500 series switches support IEEE 802.1Q tunneling and Layer 2 protocol tunneling.
More informationConfiguring VPLS. VPLS overview. Operation of VPLS. Basic VPLS concepts
Contents Configuring VPLS 1 VPLS overview 1 Operation of VPLS 1 VPLS packet encapsulation 4 H-VPLS implementation 5 Hub-spoke VPLS implementation 7 Multi-hop PW 8 VPLS configuration task list 9 Enabling
More informationHP A5120 EI Switch Series Layer 2 - LAN Switching. Command Reference. Abstract
HP A5120 EI Switch Series Layer 2 - LAN Switching Command Reference Abstract This document describes the commands and command syntax options available for the HP A Series products. This document is intended
More informationConfiguring Q-in-Q VLAN Tunnels
This chapter describes how to configure Q-in-Q VLAN tunnels. Finding Feature Information, page 1 Feature History for Q-in-Q Tunnels and Layer 2 Protocol Tunneling, page 1 Information About Q-in-Q Tunnels,
More informationTransparent CFM. Information About Transparent CFM. EFP (Q-in-Q interfaces with dot1q or dot1ad C-UNI)
CFM support on a customer VLAN (C-VLAN) allows a customer to provision maintenance intermediate points (MIPs) and Up maintenance endpoints (MEPs) on a C-VLAN component for EFP (Q-in-Q interfaces with dot1q
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 MPLS L2VPN overview 1 About MPLS L2VPN 1 Comparison with traditional VPN 2 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 Overview 1 Comparison with traditional VPN 1 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration task list 4 Configuring
More informationConfiguring VLAN-VPN CHAPTERS
CHAPTERS 1. VLAN-VPN 2. Basic VLAN-VPN Configuration 3. Flexible VLAN-VPN Configuration 4. Configuration Example 5. Appendix: Default Parameters VLAN-VPN This guide applies to: T2600G-28TS v3 or above,
More informationHP 5820X & 5800 Switch Series Layer 2 - LAN Switching. Configuration Guide. Abstract
HP 5820X & 5800 Switch Series Layer 2 - LAN Switching Configuration Guide Abstract This document describes the software features for the HP 5820X & 5800 Series products and guides you through the software
More informationSet Inner CoS Bits for QinQ
Set Inner CoS Bits for QinQ First Published: September 2007 Revised: August 2008 This document describes the Set Inner CoS Bits for QinQ feature that allows you to mark both inner and outer VLAN tags of
More informationHP MSR Router Series. Layer 2 LAN Switching Command Reference(V7)
HP MSR Router Series Layer 2 LAN Switching Command Reference(V7) Part number: 5998-7738b Software version: CMW710-R0304 Document version: 6PW104-20150914 Legal and notice information Copyright 2015 Hewlett-Packard
More informationConfiguring 802.1Q VLAN Interfaces
A VLAN is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments.
More informationH3C SR G Core Routers
H3C SR8800 10G Core Routers Layer 2 LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SR8800-CMW520-R3347 Document version: 6W103-20120224 Copyright
More informationEVC Command Reference
EVC Command Reference This chapter describes commands used to configure an Ethernet Virtual Circuit (EVC). bridge-domain, page 2 clear ethernet service instance, page 3 encapsulation, page 5 l2protocol,
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 MPLS L2VPN overview 1 Basic concepts of MPLS L2VPN 2 Implementation of MPLS L2VPN 2 MPLS L2VPN configuration task list 4 Configuring MPLS L2VPN 5 Configuring CCC MPLS
More informationHP 3600 v2 Switch Series
HP 3600 v2 Switch Series Layer 2 - LAN Switching Command Reference Part number: 5998-2361 Software version: Release 2108P01 Document version: 6W100-20131130 Legal and notice information Copyright 2013
More informationConfiguring Q-in-Q VLAN Tunnels
This chapter contains the following sections: Information About Q-in-Q VLAN Tunnels, page 1 Licensing Requirements for Q-in-Q Tunnels, page 4 Guidelines and Limitations for Q-in-Q VLAN Tunnels, page 5
More informationH3C S5820X&S5800 Series Ethernet Switches
H3C S5820X&S5800 Series Ethernet Switches Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 6W103-20100716 Product Version: Release 1110
More informationQuidway S5700 Series Ethernet Switches V100R006C01. Configuration Guide - Ethernet. Issue 02 Date HUAWEI TECHNOLOGIES CO., LTD.
V100R006C01 Issue 02 Date 2011-11-21 HUAWEI TECHNOLOGIES CO., LTD. 2011. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written
More informationOperation Manual ARP H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 ARP Overview... 1-1 1.1.1 ARP Function... 1-1 1.1.2 ARP Message Format... 1-1 1.1.3 ARP Address Resolution Process... 1-2 1.1.4 ARP Mapping Table... 1-3 1.2
More informationTable of Contents 1 Port Mirroring Configuration 1-1
Table of Contents 1 Port Mirroring Configuration 1-1 Introduction to Port Mirroring 1-1 Classification of Port Mirroring 1-1 Implementing Port Mirroring 1-2 Other Functions Supported by Port Mirroring
More informationExample: Configuring Layer 2 Protocol Tunneling on EX Series Switches
Example: Configuring Layer 2 Protocol Tunneling on EX Series Switches Requirements Layer 2 protocol tunneling (L2PT) allows you to send Layer 2 protocol data units (PDUs) across a service provider network
More informationQinQ Operation. Page 1 of 11
QinQ Operation Page 1 of 11 Chapter 1 Contents QinQ Configuration...3 1.1 Introduction to QinQ... 3 1.1.1 Understanding QinQ...3 1.1.2 Implementations of QinQ...4 1.1.3 Modification of TPID Value of QinQ
More informationARP attack protection commands
Contents ARP attack protection commands 1 Unresolvable IP attack protection commands 1 arp resolving-route enable 1 arp source-suppression enable 1 arp source-suppression limit 2 display arp source-suppression
More informationGVRP configuration commands
Contents GVRP configuration commands 1 display garp statistics 1 display garp timer 2 display gvrp local-vlan 3 display gvrp state 3 display gvrp statistics 5 display gvrp status 6 display gvrp vlan-operation
More informationTable of Contents Chapter 1 Configuration File Management Commands
Table of Contents Table of Contents... 1-1 1.1.1 display current-configuration... 1-1 1.1.2 display saved-configuration... 1-6 1.1.3 display this... 1-7 1.1.4 display startup... 1-8 1.1.5 reset saved-configuration...
More informationFSOS. Ethernet Configuration Guide
FSOS Ethernet Configuration Guide Contents 1 Configuring Interface... 1 1.1 Overview...1 1.2 Configuring Interface State...1 1.2.1 Configurations...1 1.2.2 Validation...1 1.3 Configuring Interface Speed...
More informationVLAN Subinterface Commandsonthe Cisco IOS XR Software
VLAN Subinterface Commandsonthe Cisco IOS XR Software This module provides command line interface (CLI) commands for configuring 802.1Q VLANs on the Cisco CRS Router. The maximum VLAN limit that can be
More informationACSEI configuration commands
Contents ACSEI configuration commands 1 acsei client reboot 1 acsei server 1 acsei server enable 2 acsei timer clock-sync 2 acsei timer monitor 3 display acsei client info 3 display acsei client summary
More informationH3C S5130-EI Switch Series
H3C S5130-EI Switch Series OpenFlow Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 311x Document version: 6W102-20180323 Copyright 2016-2018, New H3C Technologies
More informationEthernet Interface Configuration Commands
Table of Contents Ethernet Interface Configuration Commands 1 General Ethernet Interface/Subinterface Configuration Commands 1 combo enable 1 description 1 display interface 2 display interface brief 9
More informationEthernet Virtual Connections Configuration
An Ethernet Virtual Connection (EVC) is defined by the Metro-Ethernet Forum (MEF) as an association between two or more user network interfaces that identifies a point-to-point or multipoint-to-multipoint
More informationEthernet Interface Configuration Commands
Table of Contents Ethernet Interface Configuration Commands 1 General Ethernet Interface/Subinterface Configuration Commands 1 combo enable 1 description 1 display interface 2 display interface brief 9
More informationConfiguring SPAN and RSPAN
34 CHAPTER This chapter describes how to configure the Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) on the Catalyst 4500 series switches. SPAN selects network traffic for analysis by a network
More informationIEEE 802.1Q-in-Q VLAN Tag Termination
IEEE 802.1Q-in-Q VLAN Tag Termination Encapsulating IEEE 802.1Q VLAN tags within 802.1Q enables service providers to use a single VLAN to support customers who have multiple VLANs. The IEEE 802.1Q-in-Q
More informationConfiguring Ethernet Virtual Connections on the Cisco ASR 1000 Series Router
Configuring Ethernet Virtual Connections on the Cisco ASR 1000 Series Router Ethernet virtual circuit (EVC) infrastructure is a Layer 2 platform-independent bridging architecture that supports Ethernet
More informationConfiguring SPAN. Understanding SPAN CHAPTER. This chapter describes how to configure Switched Port Analyzer (SPAN) and on the Catalyst 2960 switch.
CHAPTER 23 This chapter describes how to configure Switched Port Analyzer (SPAN) and on the Catalyst 2960 switch. Note For complete syntax and usage information for the commands used in this chapter, see
More informationEthernet interface commands
Contents Ethernet interface commands 1 Common Ethernet interface commands 1 default 1 description 2 display counters 2 display counters rate 4 display interface 5 display interface brief 12 display packet-drop
More informationH3C S6800 Switch Series
H3C S6800 Switch Series OpenFlow Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2609 and later Document version: 6W103-20190104 Copyright 2019, New H3C Technologies
More informationConfiguring Access and Trunk Interfaces
Configuring Access and Trunk Interfaces Ethernet interfaces can be configured either as access ports or trunk ports. Trunks carry the traffic of multiple VLANs over a single link and allow you to extend
More informationH3C S3100V2 Switch Series
H3C S3100V2 Switch Series Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5103 Document version: 6W100-20110620 Copyright 2011,
More informationTable of Contents 1 Monitor Link Configuration Commands 1-1
Table of Contents 1 Monitor Link Configuration Commands 1-1 Monitor Link Configuration Commands 1-1 display monitor-link group 1-1 monitor-link group 1-2 port 1-2 port monitor-link group 1-3 i 1 Monitor
More informationQ-in-Q Encapsulation Mapping for EPGs
, on page 1 Configuring Using the GUI, on page 2 Mapping EPGs to Q-in-Q Encapsulated Leaf Interfaces Using the NX-OS Style CLI, on page 5 Mapping EPGs to Q-in-Q Encapsulation Enabled Interfaces Using the
More informationLayer 2 Access Control Lists on EVCs
The ability to filter packets in a modular and scalable way is important for both network security and network management. Access Control Lists (ACLs) provide the capability to filter packets at a fine
More informationConfiguring SPAN and RSPAN
41 CHAPTER This chapter describes how to configure the Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) on the Catalyst 4500 series switches. SPAN selects network traffic for analysis by a network
More informationHP A3100 v2 Switch Series
HP A3100 v2 Switch Series Layer 2 - LAN Switching Configuration Guide HP A3100-8 v2 SI Switch (JG221A) HP A3100-16 v2 SI Switch (JG222A) HP A3100-24 v2 SI Switch (JG223A) HP A3100-8 v2 EI Switch (JD318B)
More informationVPLS configuration commands
Contents VPLS configuration commands 1 car 1 description 1 display bgp vpls 2 display l2vpn fast-switch-group 7 display mac-address vsi 8 display mpls l2vpn fib ac vpls 10 display mpls l2vpn fib pw vpls
More informationH3C S6300 Switch Series
H3C S6300 Switch Series Layer 2 LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 23xx Document version: 6W101-20150407 Copyright 2014-2015,
More informationVPLS configuration commands
Contents VPLS configuration commands 1 bandwidth 1 broadcast-restrain 1 description 2 display bgp vpls 3 display l2vpn fast-switch-group 8 display mac-address vsi 9 display mpls l2vpn fib ac vpls 10 display
More informationPPP configuration commands
Contents PPP configuration commands 1 ip address ppp-negotiate 1 ip pool 1 link-protocol ppp 2 ppp authentication-mode 2 ppp chap password 4 ppp chap user 5 ppp ipcp remote-address forced 5 ppp pap local-user
More informationHP FlexFabric 5700 Switch Series
HP FlexFabric 5700 Switch Series Layer 2 LAN Switching Configuration Guide Part number: 5998-6686 Software version: Release 2416 Document version: 6W100-20150130 Legal and notice information Copyright
More informationASR 9000 Series Common Problems with Spanning Tree Protocols
ASR 9000 Series Common Problems with Spanning Tree Protocols Document ID: 116514 Contributed by Bryan Garland and David Powers, Cisco TAC Engineers. Sep 19, 2013 Contents Introduction Problem Port VLAN
More informationConfiguring VLANs. Understanding VLANs CHAPTER
CHAPTER 9 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094). It includes information about VLAN membership modes, VLAN configuration
More informationHPE FlexNetwork 5510 HI Switch Series
HPE FlexNetwork 5510 HI Switch Series Layer 2 LAN Switching Command Reference Part number: 5200-0074b Software version: Release 11xx Document version: 6W102-20171020 Copyright 2015, 2017 Hewlett Packard
More informationTable of Contents. 1 TFTP Configuration Commands 1-1 TFTP Client Configuration Commands 1-1 tftp-server acl 1-1 tftp 1-2 tftp ipv6 1-3
Table of Contents 1 TFTP Configuration Commands 1-1 TFTP Client Configuration Commands 1-1 tftp-server acl 1-1 tftp 1-2 tftp ipv6 1-3 i 1 TFTP Configuration Commands TFTP Client Configuration Commands
More informationAutoQoS. Prerequisites for AutoQoS CHAPTER
64 CHAPTER Prerequisites for, page 64-1 Restrictions for, page 64-2 Information About, page 64-2 Default Settings for, page 64-4 How to Configure, page 64-4 For complete syntax and usage information for
More informationAppendix A Command Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
The command index includes all the commands in the VRP Command Manual, which are arranged alphabetically. A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A access-limit 1-1 accounting QoS 2-1 accounting
More informationVLAN Range. Feature Overview
VLAN Range Feature History Release 12.0(7)XE 12.1(5)T 12.2(2)DD 12.2(4)B 12.2(8)T 12.2(13)T Modification The interface range command was introduced. The interface range command was integrated into Cisco
More informationVLAN Range. Feature Overview
VLAN Range Feature History Release 12.0(7)XE 12.1(5)T 12.2(2)DD Modification The interface range command was introduced. The interface range command was integrated into Cisco IOS Release 12.1(5)T. The
More informationH3C S5130-HI Switch Series
H3C S5130-HI Switch Series Layer 2 - LAN Switching Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 1111 Document version: 6W100-20150615 Copyright 2015,
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series ACL and QoS Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5501 Document version: 6W100-20140103 Copyright 2014, Hangzhou
More informationEthernet interface configuration commands
Contents Ethernet interface configuration commands 1 General Ethernet interface and subinterface configuration commands 1 alarm-detect 1 bandwidth 2 combo enable 2 default 3 description 4 display counters
More informationTL-SG5428 TL-SG5412F. 24-Port Gigabit L2 Managed Switch with 4 SFP Slots. 12-Port Gigabit SFP L2 Managed Switch with 4 Combo 1000BASE-T Ports REV2.1.
TL-SG5428 24-Port Gigabit L2 Managed Switch with 4 SFP Slots TL-SG5412F 12-Port Gigabit SFP L2 Managed Switch with 4 Combo 1000BASE-T Ports REV2.1.1 1910010847 COPYRIGHT & TRADEMARKS Specifications are
More informationEthernet interface configuration commands
Contents Ethernet interface configuration commands 1 General Ethernet interface/subinterface configuration commands 1 combo enable 1 default 1 description 2 display counters 3 display counters rate 4 display
More informationTable of Contents 1 WLAN Security Configuration Commands 1-1
Table of Contents 1 WLAN Security Configuration Commands 1-1 authentication-method 1-1 cipher-suite 1-2 gtk-rekey client-offline enable 1-2 gtk-rekey enable 1-3 gtk-rekey method 1-4 ptk-lifetime 1-5 security-ie
More informationH3C S5120-EI Switch Series
H3C S5120-EI Switch Series IP Multicast Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2210 Document version: 6W100-20110915 Copyright 2011, Hangzhou
More informationResilient Ethernet Protocol (REP)
The is a Cisco proprietary protocol that provides an alternative to the Spanning Tree Protocol (STP). REP provides a way to control network loops, handle link failures, and improve convergence time. It
More informationH3C MSR Router Series
H3C MSR Router Series Comware 7 OpenFlow Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: MSR-CMW710-R0615P08 Document version: 6W201-20180803 Copyright 2017-2018,
More informationHP 5130 EI Switch Series
HP 5130 EI Switch Series Layer 2 LAN Switching Command Reference Part number: 5998-5480a Software version: Release 31xx Document version: 6W100-20150731 Legal and notice information Copyright 2015 Hewlett-Packard
More informationEthernet Overhead Accounting
The feature enables the router to account for downstream Ethernet frame headers when applying shaping to packets. Finding Feature Information, page 1 Restrictions for, page 1 Information About, page 2
More informationMonitor Commands. monitor session source, page 2 monitor session destination, page 4
monitor session source, page 2 monitor session destination, page 4 1 monitor session source monitor session source To create a SPAN or RSPAN source session, use the monitor session source command in switch
More informationCommand Reference for Voice VLAN
APPENDIX A This section provides reference information for the following voice VLAN commands: interface range, page A-1 interface vlan, page A-3 monitor session, page A-4 spanning-tree, page A-6 spanning-tree
More informationConfiguring VLANs. Understanding VLANs CHAPTER
7 CHAPTER This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the Cisco MWR 2941 router. It includes information about VLAN
More informationConfiguring VLANs. Understanding VLANs CHAPTER
CHAPTER 11 This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and extended-range VLANs (VLAN IDs 1006 to 4094) on the Cisco ME 3400 Ethernet Access switch. It includes information
More informationH3C SecPath Series High-End Firewalls
H3C SecPath Series High-End Firewalls Attack Protection Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SECPATHF1000SAI&F1000AEI&F1000ESI-CMW520-R3721 SECPATH5000FA-CMW520-F3210
More informationH3C S9500 Series Routing Switches
Command Manual Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Manual Version: T2-08194S-20081225-C-1.24 Product Version: S9500-CMW310-R1648 Copyright 2007-2008, Hangzhou H3C Technologies Co., Ltd.
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series Layer 2 - LAN Switching Command Reference Part number: 5998-5320a Software version: Release 23xx Document version: 6W101-20150320 Legal and notice information Copyright 2015
More informationConfiguring Spanning Tree Protocol
CHAPTER 7 This chapter descibes how to configure Spanning Tree Protocol (STP) on the Cisco wireless mobile interface card (WMIC). Note For complete syntax and usage information for the commands used in
More informationTable of Contents 1 MSTP Configuration Commands 1-1
Table of Contents 1 MSTP Configuration Commands 1-1 MSTP Configuration Commands 1-1 active region-configuration 1-1 bpdu-drop any 1-1 check region-configuration 1-2 display stp 1-3 display stp abnormalport
More informationH3C S6300 Switch Series
H3C S6300 Switch Series Layer 2 LAN Switching Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 23xx Document version: 6W101-20150407 Copyright 2014-2015,
More information24-Port 10/100 L3 Switch Model: Web Configuration Guide
24-Port 10/100 L3 Switch Model: 065-7434 Web Configuration Guide Table of Contents PREPARATIONS... 6 OVERVIEW... 6 Login... 6 PRODUCT INFORMATION... 9 OVERVIEW... 9 FEATURES... 9 SYSTEM VERSION INFORMATION...10
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series OpenFlow Command Reference Part number: 5998-4679a Software version: Release 23xx Document version: 6W101-20150320 Legal and notice information Copyright 2015 Hewlett-Packard
More informationAppendix A Command Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
The command index includes all the commands in the Comware Command Manual, which are arranged alphabetically. A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A access-limit accounting accounting optional
More information