Product information IP Video Streamer FBI6110

Transcription

1 Product information IP Video Streamer FBI6110

2 2 03/2013 Table of contents Scope of delivery... 3 Safety instructions... 3 General safety regulations... 3 Installation protective measures... 3 Terms... 3 Technical data... 4 Indication and operation elements... 4 Device overview... 5 Intended use... 5 Short description... 5 Connect the lines... 6 Note... 6 Connection lines to the TCS system... 6 Connect the device... 6 Wiring diagram with SIP-Gateway... 7 Connection diagram... 7 Commissioning... 8 Error detection and indication... 8 Decommissioning... 8 Settings... 9 Reload to factory settings... 9 Start browser: connection establishment PC IP Video Streamer... 9 Prepare the network connection... 9 Live transmission Image reproduction Settings Video Network General Video sources Control Time/date Change the password Password Administrator Password User Forgot password? Password Administrator Password User Send short message Short message to a group Short message to all devices Accessibility from the internet Setup with static IP address Setup with dynamic IP address and usage of a DynDNS service IT safety Useful notes How is the IP address of the PC/Laptop identified? How is ensured if the IP address of the Video Streamer is already used? FAQ Spare parts, accessory... 26

3 03/ Conformity Information on disposal Warranty Notes Service x FBI (with SD card 2 GB) product information Scope of delivery General safety regulations Safety instructions! Attention! Mounting, installation, commissioning and repair of electronic devices have to be carried out only by qualified electricians. Thus, the current standards for the installation of door communication systems must be observed. For working on systems with main connection of 230 V alternating voltage, the safety regulations according to DIN VDE 0100 must be observed. When installing TCS:BUS systems, the general safety regulations for telecommunication systems according to VDE 0800 (and EN60950 safety standard for information technology equipment must be observed. Inter alia: separated conduit of heavy and low current lines, minimum distance of 10 cm in case of a common conduit, use of separators between heavy and low current lines within shared cable ducts, use of standard communication lines, e.g. J-Y (St) Y with 0.8 mm diameter, existing lines (modernisation) with deviating cross-sections can be used in compliance with the loop resistance. Installation protective measures! With suitable measures to protect against lightning, it has to be ensured that a voltage of each 32 V DC is not exceeded at the connections. Terms MJPG Ring buffer MJPEG (Motion JPEG) is a codec, where every single image is compressed as JPEG image with a compression rate of 1:5 to 1:13. The quality of MJPEG is-independent of movement. A ring buffer stores data continuously in a determined period of time and overwrites this data again after the preset time is up in order to provide storage space for new data.

4 4 03/2013 Technical data supply voltage: +26 V ± 8 % (power supply and control unit) housing: DIN-rail housing 6 SU for DIN-rail mounting DIN EN weight 180 g acceptable ambient temperature: 0 C C input current: I(a) = 0.2 ma, I(P) = 110 ma max. input current: I(Pmax) = 135 ma input impedance: 100 Ohm balanced 6-wire technique necessary! Indication and operation elements Term LED, green: indication for operational readiness LED, yellow: error indication network and SD card LED, red: error indication TCS:BUS RJ45 socket LAN 1 RJ45 socket LAN 2 each with LED, yellow and LED, green push button reset push button WE Function ON: device is ready for operation blinks: during start and update procedure flashes: error in the network connection or SD card is missing or defect flashes: error in the connection to the TCS:BUS connection to the network connection to the SIP-Gateway (if used) LED, yellow: indicates data current LED, green: ON, if the FBI6110 is connected to the network resp. with the SIP-Gateway to reset the FBI6110 to reload the factory setting of the FBI6110

5 03/ Device overview connection SIP-Gateway connection network Indication for operational readiness (LED, green) error indication network and SD card (LED, yellow) error indication TCS:BUS (LED, red) SD card slot. J1: matching resistor connection terminal TCS:BUS and Video push button reload to factory setting push button reset Intended use The FBI6110 is a Linux-based web server to connect TCS video systems to network. It is suitable for DIN-rail mounting according to DIN EN Short description browser-based usage and configuration, no programme and driver installation necessary (condition: JavaScript and Java) triggering of control functions with status indication via web interface video transmission via JPEG stream, MJPG (up to 10 simultaneous accesses) resolution color: 320 x 240 pixel image transmission rate from 1 to 10 images per second, can be adjusted automatic image storage in case of a door call on SD carte (enclosed in the delivery) storage of max. 100 still images with date and time in ring buffer password protected against unauthorised configuration

6 6 03/2013 error indication, optical (LED) integrated two-wire video receiver for direct connection to TCS video systems RJ45 socket for connection to the network (10/100 Base-TX) RJ45 socket to connect a SIP-Gateway via an integrated switch browser-based possibilty to send short messages to video indoor stations (ecoos IVW221x, sky IVW2221 or skyline IVW3012). Connect the lines Note! Use a small screwdriver to connect lines and to avoid damaging the device. Connection lines to the TCS system acceptable cross-section (diameter) max. number of wires per terminal contact mm 2 (Ø mm) each 2 x Ø 0.8 mm or 3 x Ø 0.6 mm Connect the device Connect the device according to the wiring diagram. Establish a connection between the socket LAN1 at the Video Streamer and your network with a standard network cable.

7 03/ Wiring diagram with SIP-Gateway floor push button network Connection diagram

8 8 03/2013 Commissioning! First install the system completely, than connect it to the mains voltage! V1 and V2 must not be connected with the P-, a- or b-wire. When connecting the video wires V1 (+) and V2 ( ) the polarity must be observed. If you see a distorted picture after the commissioning, switch off the device and exchange the wires for the video signal. Ensure that the SD card is plugged accordingly to the marking on the type label in the SD slot. The SD card is necessary for the storage of all configuration data and images. The card must always be in the device.! For a safe functionality, only the enclosed SD card is to be used. The SD card can be ordered as spare part directly at TCS (see Spare parts, accessory, page 26). Switch on the mains voltage, the Video Streamer starts automatically. The LED indication (green) blinks for around 10 seconds and shines. The device is now ready for operation. Error detection and indication Errors when connecting the cables are signaled by flashing of the LED indication (red or yellow). The optical error indication stays active until the error is corrected. error causes a- and P-wire are mixed or short-circuited a-wire not connected or not supplied indication error mode LED, flashes red our solution Exchange a- and P-wire or correct short-circuit, LED expices. Connect the a-wire or establish power supply, LED expices. error to the network connection or SD card is missing LED, flashes yellow Check the connection to the network, the SD card is plugged in and whether the PC is operating. Decommissioning For certain activities on the system such as maintenance, the Video Streamer must be removed from operation: Switch off the power supply of the system.

9 03/ Reload factory settings! Settings When reset to factory settings, only the IP settings and passwords are reset to factory setting. If the adjusted IP address or the administrator password is not known, the device can be reset to factory settings: IP address: subnet mask: user: admin password: 1234 LED, lights up green LED, blinks green LED, blinks fast green LED, lights up green press push button reset to factory setting and keep it pressed keep push button reset to factory setting pressed, until the LED blinks fast, then release it device is reset to factory settings Start browser: establish a connection PC IP Video Streamer Prepare the network connection The PC/Laptop must be equipped with a network connection and it must be located in the same subnet as the Video Streamer. If your network and the Video Streamer are working within the address area (C net), you have direct access to the Video Streamer (provided that this IP address is not used by another device). Otherwise, the used PC/laptop has to be switched temporarily to an IP address within the address area of the FBI6110 in order to establish a connection with the Video Streamer. To establish/ adjust your network connection, please use the network installation assistant or the help function of your operating system, keyword: set up network. If several FBI6110 (in delivery state) are to be installed within one network, the devices have to be commissioned one after another and a free IP address has to be assigned. To set up the network connection, you may need administrator rights. In delivery state, the following is preset at FBI6110: IP address: subnet mask: user: admin password: 1234

10 10 03/2013 Live transmission Open an internet browser. Enter the IP address in the address line of the Video Streamers: The start page of the web interface is called. Select Live transmission. The image of the current video front-door station or camera appears. In case of an incoming call, the image of the calling video front-door station appears automatically. After a door call is realised to the TCS:BUS an upstream video switch FVU1210 resp. VSW04 switches to the channel, which was configured with the corresponding AS address. The FBI6110 monitors the TCS:BUS permanently and in this case updates the indication of the video source within the webinterface when the menu live transmission is active. Further, a still picture is recorded automatically and stored on the SD card, if this feature was activated for this AS address (video source) under Settings. Operation button video step open the door store an image zoom + / function The images of all connected TCS video sources can be switched in sequence. Can open the door at the current video front-door station. Manual saving of the currently visible image on the SD card. The file name is given automatically (format: date_time). Zoom in (zoom +) or zoom out (zoom ) the video image in one step. Switch the camera

11 03/ camera selection list Drop-Downmenu over the image field (e.g. post, side entrance, ) explanation Here, all available TCS cameras can be called directly. The camera selection list shows all video sources, which were activated in the menu video sources in order to be displayed in the camera selection list. You can select the names of the video sources freely (max. 20 characters). The order of the cameras is the order in which the cameras were created in the configuration overview (see Video sources, page. 16). Trigger the controling toolbar Button 1 Button 10 explanation With these buttons, a control function can be sent to the TCS:BUS and thus, a switching process at another TCS:BUS device can be triggered. The status indication (if available, see graphic below) is influenced by the control functions, which were sent by the Video Streamer and other TCS:BUS devices to the TCS:BUS. Operation and indication elements are created by the administrator in the corresponding configuration menu. (see Control, page 17) The status indication is updated every 2 seconds. Status indication Button 1 Button 1 Button 1 Button 1 Button 1 FBI or extent TM Switching and switching state 1 ON/OFF FBI or extent TM Switching and switching state 2 OFF/ON FBS FBS BRE only indication switching state ON only indication switching state OFF switching without status indication Note Between control functions, which are offered by the TCS:BUS, also products of the series extent can be integrated in the Video Streamer. It is possible to get information on the switching state between the usual switching acts. The status of the sensors of the extent series can be displayed directly on the Video Streamer.

12 12 03/2013 Image reproduction Note: In every menu, a Back button is available. By pressing the button you can go back to the start page. <-back Select Image reproduction on the start page. The image stored last is displayed. Via a drop-down menu above the image field all available images can be selected and displayed according to a known time and a known date. The currently displayed image can be deleted by pressing the Delete button. Streamer Note In case of an incoming door call an image is stored automatically, if the video source was configured for this purpose. Up to 100 images can be stored, older images are deleted automatically. Settings Open an internet browser. Enter the IP address in the address line of the Video Streamer: The start page is called. Select Settings. Enter the user name and the password (pre-adjusted: admin and 1234) and click OK.

13 03/ Video Enter the data. Confirm with the Save button, the settings are stored. The button Reset resets the content to the last stored state. The device is not reset to factory settings. Parameter number of image per second video port ( ) Explanation Shows, how many images are forwarded as video. Only every x th image is sent (1 to 10 images /s are possible). If image errors or image dropouts occur when reproducing the image within the network or in the Internet, the available bandwidth is not enough. The refresh rate must be slowed down. Port, over which the video stream is realised. Ports from 1025 to are possible. Factory setting=

14 14 03/2013 Network Enter the data. Confirm with the Save button, the settings are stored. The button Reset resets the content to the last stored state. No reload to factory setting is realised. Parameter IP address subnet mask Explanation Assign a free IP address within xou network to the Video Streamer, also see Useful, page 24) Register the associated subnet mask (usually ) standard Gateway Gateway. Enter the internal IP address of your router or server as standard primary DNS Enter the internal IP address of your router or server as primary DNS. secundary DNS Enter, if available, the internal IP address of your router or server as secondary DNS. External IP address of the router with port External IP address of the router with associated port for the video transmission, separated by a colon. Observe our notes on Accessibility from the Internet, page 23. After a restart, the Video Streamer can be contacted under the configured IP address. Note If the IP address was changed manually, the web browser may not be able to display the web page with the feedback. If this is the case, enter the new IP manually into the browser to get back to the main page.

15 03/ General Enter the data. Confirm with the Save button, the settings are stored. The button Reset resets the content to the last stored state. No factory setting is realised. Parameter device name language start site: live transmission short message PIN firmware and hardware versions Explanation Here, a name can be assigned to the FBI6110 in order to identify the device. The name appears on the site Live transmission. Via the selection menu Language you can select with the current variant the languages German, English, French, Italian and Spanish. According to the selection, all menus are converted to the selected language. If this option is selected, you will be forwarded automatically to the site live transmission when entering the IP address of the Video Streamer in your web browser. For sending short messages, it is necessary to enter a PIN (alpha alphanumeric) with 4 digits. Here, you can change the PIN. Preset factory setting: Also see Send short message, page 21. Indication of device internal data.

16 16 03/2013 Video sources By entering the data in this table, video sources to specifically switch on the connected video cameras are created (max. 16). Enter a camera name. The name appears in the camera selection list. Confirm with the Save button, the settings are stored. The button Reset resets the content to the last stored state. No reload to factory setting is realised. Parameter name AS address indication image storage Explanation Name of the camera, as it should be shown in the camera selection list. AS address of the camera to realise a switch-over via the VSW04 or FVU1220. The AS address is permanently assigned to the button. Each AS address in the range from 0 to 63 can be assigned only once. To activate or deactivate the display of the camera in the camera selection list (menu Live transmission). To activate or deactivate die automatic image storage in case of door calls.

17 03/ Control In the menu Control, displayed buttons and status indications can be configured. For an implementation within a TCS:BUS system, the following devices are used (depending on requirements): FBI4200, BRE2 or FBS1100. Enter the data. Confirm with the Save button, the settings are stored. The button Reset resets the content to the last stored state. No reload to factory settings is realised. Parameter Explanation name Unique name to display in the menu: Live transmission. The serial number of the connected devices resp. function is entered serial number here. control function This number determines the importance and function of the sent or received control protocol at the TCS:BUS. Only to be entered if the BRE is selected. channel number The channel number of a connected FBI4200 is entered here. Only to be entered if the FBI is selected. type Three types of devices can be selected: FBI, BRE and FBS (see table below) To activate or deactivate the display of the function Name in the menu indication Live transmission FBS status indication status indication (ON = control function 1 or 3, OFF = control function 2 or 4) Device Entry created Function Enter in overview type FBI button with status indication channel functions with status indication (parallel run with IMM1100) channel number, serial number of the FBI or extent BRE button send control function serial number and control function number serial number

18 18 03/2013 Time/date Enter the data. Confirm with the Save button, the settings are stored. The button Reset resets the content to the last stored state. No reload to factory settings is realised. Parameter time server time zone summer time automatically Explanation Address of the server, which system time is loaded as current time. Time/date are downloaded automatically via a time server in the internet or in your network (factory setting: ntp1.ptb.de) Here, the time zone for the system time can be selected. The time refers to the standard time GMT. Only GMT is displayed, summer and winter time are not taken into account. For considering summer and winter time, the option must be activated.

19 03/ Change the password For safety reasons, it is recommended to change the password. Password Administrator Enter your desired password and repeat the entry. Confirm with the Save button. To determine a new administrator password click on Administrator and enter the desired password and repeat the entry. Click on Save. Password User Ex works, there is no set password. Only the administrator can set the password User. The start page can be called only after entering the password. Enter the required password and repeat the entry. Confirm with the Save button. The administrator can remove the password: Saving without filling in the fields. You can also remove the administrator password, if there is no need for safety. Save without filling in the fields.! Observe that other persons can manipulate the device without password protection!

20 20 03/2013 Forgot password? Password Administrator To ensure the access for the administrator, the device can be reset to factory settings.! When resetting to factory settings, only the IP settings and passwords are reloaded to factory setting. The network factory settings are: IP address: Subnet mask: User: admin Password: 1234 Password User Only the administrator can change or delete the password User.

21 03/ Send short message In the menu TCS:BUS Short message, a short message (sms) can be send to the video indoor stations of a group or to all video indoor stations (ecoos IVW221x, sky IVW2221 or skyline IVW3012). Short message to a group Select Group of devices. Enter the required Group digit. Fill in the required text of the short message into the field Text. Enter the PIN with four digits. Click Send. The short message is received at the specific video indoor stations. Short message to all devices Select All devices. Fill in the required text of the short message into the field Text. Enter the PIN with four digits. Click Send. The short message is received at the specific video indoor stations.

22 22 03/2013 Parameter group of devices all devices group text short message PIN reset Explanations Select Group of devices, if you want to send a short message to a group of video indoor stations. Select All devices, if you want to send a short message to all video indoor stations. Enter the group digit (0 to 63) of the video indoor stations, which are to receive the short message. Note: The group digits from 0 to 63 are not pre-defined. They must be created individually. The group allocation is realised with the configuration software configo TM. Thus, the digit for the input field Group is similar to the digit to send a short message as defined in configo TM. We recommend to create a list e.g. Group 1: flats 1. Top floor right, Group 2: flats 1. Top floor left etc.. For further information on group assignment, see product information of the specific video indoor station. Input field for the text of a short message to the selected video indoor stations. Note: Max. 39 characters permitted. Unknown characters e.g. special characters are converted into blank spaces. To send a short message, an alpha numerical Pin with four digits needs to be entered. Pre-setting ex works: These can be adjusted under Settings \ General, page 15. The Reset button resets the content to the last stored status. No reset to factory setting is realised. Note After the successful sending of a short message, the image activation button of the specific video indoor station blinks. To read and delete the message, follow the instructions as described in the product information of the specific video indoor station (ecoos IVW221x, sky IVW2221 or skyline IVW3012).

23 03/ Accessibility from the internet To ensure the accessibility of the Video Streamer, an internet connection with static IPaddress is necessary. In case of a DSL connection, the IP-address is assigned anew by the internet provider with each call and max. after 24 hours. For this type of internet connection a DynDNS service can be used alternatively. Thus, your router must be equipped with the following features: support of DynDNS port extension (port forwarding) Please ensure that the router is equipped with this features when purchasing one. Setup with static IP address In the menu of the router, the following configurations are necessary. Generally you ll find the settings under a menu point port forwarding or similar. The port for the web server is to be lead to the Video Streamer. If you don t operate another webserver within the network, you can state 80 as external port. If the port 80 is already used by another webserver, please select a free port. Note In this case your Video Streamer can be accessed via internet in the browser by the entry: IP address: Port. As internal port, the 80 is to be entered. As internal IP address enter the IP address of the Video Streamer. The port for the video transmission is to be lead to the router too. Enter the video port which is set under Settings Video stream as internal and external port. As internal IP address enter the IP address of the Video Streamer. In the Video Streamer, the following configurations in the menu Network are necessary: Enter the internal IP address of your router as Gateway. As external IP/DynDNS address, enter the external IP address of your router and the external port for the video transmission, separated by a colon. Press the Save button. Setup with dynamic IP address and usage of a DynDNS service Notwithstanding the indicated above, the following works have to be done: Registration e.g. under or dynips.net First register at the service provider. Enter the required name there, the IP address is filled-in automatically. Configuration in the router: Under the menu point DynDNS your selected address (e.g. your name.dyndns.org) must be entered and activated. Configuration in the Video Streamer (network): As external IP/DynDNS address, you have to enter your selected address, followed by a colon and the port for the video transmission. Press the Save button.

24 24 03/2013 IT safety Server are easy targets of attack, if they are available unprotected in the internet. TCS recommends to secure the access to the Video Streamer and to establish the connection via VPN. Therefore, you should find a safe server in the internet, which is equipped with an installed VPN server. A various number of DSL router supports the setup of a VPN network. Via the protected network you can communicate securely, because only VPN participants have access to the server. Please contact your administrator for further information. Useful notes How is the IP address of the PC/Laptop identified? Open the command prompt on your PC/Laptop. Entert he command ipconfig (Windows 2000 or XP). Read out the IP address. How is determined whether the IP address of the Video Streamer is already used? Open the command prompt on your PC/Laptop. Enter the command ping If you receive an answer from another device in case of a connected Video Streamer, the specific network device must be separated from the network until you have configured the Video Streamer (via Network, page 14) with a free IP address.

25 03/ FAQ Error Cause Solution The indication for operational readines of the Video -Streamer is not active. The Video Streamer is not supplied with voltage. Check if the Video Streamer is connected with the TCS:BUS of the front-door station. Check if the power supply and control unit is connected to the TCS:BUS and voltage-supplied. Measure the DC voltage between the a- and P- terminals. The value should be at least 24 V. I m not able to access the Video Streamer with my browser The browser starts, but there is no image. The PC is not located in the same network segment as the Video Streamer. The JavaScript certificate was not installed correctly. The used browser does not support Java. Check the network settings or ask your administrator. Start the browser manually. Enter the URL (IP address) of your Video Streamer into the address line. A window opens, in which you should install a certificate. Confirm the request for the installation. You should see an image now. Activate Java within the browser settings. There is only a blue screen. The image of the analogue camera is weak with very low contrast. There is only a distorted image. No short message is received the video indoor station. There is no camera signal at the Video Streamer. The video wires are twisted. Incorrect input of the short message PIN. Incorrect input of the group digit Check if there is an incoming video signal at V1 and V2 by using a two-wire video receiver (FVW1001) and a monitor. In case of long lines, strengthen the video signal by using the active video distributor FVY1200. Measurement 1: (b or M to V1), result DC Volt, Measurement 2: (b or M to V2), result DC Volt, In case of 0 V there is a short-circuit after b/m, in case of V a short-circuit after P or a. Check the matching resistors. Use ev. a FVY1200 to strengthen the signal. Switch off the TCS:BUS and exchange the wires. Correct the PIN and try it again. Ensure that the PIN have 4 digits. Ev. change the PIN under settings \ General, page 15. Control the group membership. Check, if the digit in the field Group is similar to the digit, which you assigned to this group within configo TM. Ev. change the group digit.

26 26 03/2013 Spare parts, accessory Short text SD card for FBI / FVM Article number E33392 Conformity The device meets the requirements of the EU directive 2004/108/EG by respecting the standards: EN , EN Declarations of conformitiy for download under Downloads, trade information. Information on disposal This device has to be disposed separately from domestic waste. The materials used are recyclable. Please do help protecting our environment and dispose the device via a collection point for electronic scrap. Dispose the parts of the packaging in collecting tanks for cardboard and paper resp. plastics. Warranty We offer a simplified processing in case of warranty for electricians. Please note our conditions of sale and delivery, to download from Bed_TCSAG_2012-uk.pdf. Please contact the TCS HOTLINE.

27 03/ Notes

28 28 03/2013 Service Please send your questions and inquiries to Headquarters TCS TürControlSysteme AG, Geschwister-Scholl-Str. 7, D Genthin Phone: +49 (0) 3933 / , Fax: +49 (0) 3933 / , info@tcsag.de,