Product information Maintenance package USB FBI1210-0

Transcription

1 Product information Maintenance package USB FBI Subject to technical changes FAX: +49 (0) 41 94/ Mail: info@tcs-germany.de PI_FBI1210_uk 1A mi

2 2 02/2013 Scope of delivery 1 x PC Service interface FBI x CD: TCS Software 1 x EEPROM adapter 1 x Connector board (FBI1210) 1 x USB cable for PC, 1 m 1 x Cable assembly, 4-wires 1 x Patch cord RJ45 CAT.5e FTP (8-pin, 2 m) 1 x Handset ISH3030 Product information Safety instructions! Attention! Mounting, installation, commissioning and repair of electronic devices have to be carried out only by qualified electricians. The standards and instructions for the installations of systems must be observed. The device is only suitable for a connection to a USB port at a PC. The housing may only be opened at the manufacturer s site. Additions or modifications to the device are not allowed and void the warranty Device overview USB jack for PC I 2 C-jack for EEPROM board RJ45 jack for TCS:BUS status LED RJ11 jack for handset FAX: +49 (0) 41 94/ Mail: hotline@tcsag.de PI_FBI1210_uk 1A mi

3 02/ Description Function LED Display and operating elements Status indication for operation and serial communication OFF: out of operation ON: in operation Flash OFF: FBI1210 sends / receives UART protocols at/from PC Intended use The maintenance package USB FBI is suitable for configuration, monitoring and maintenance of TCS systems. The enclosed interface connects a PC (Laptop) with a TCS system. It should be used indoors. For a short period, it can also be used outdoors, if protected against rain (temperature 0 to 40 C).! The maintenance package USB is only licensed for the use with full versions of configurators. The user software on the TCS-CD is only for informational and testing purposes. Short description Consists of maintenance interface and TCS-CD TCS-CD encloses: a) driver for maintenance interface, b) limited full version for user software, that requires a license key subject to charge (PCitACC and call central), c) full version of configurators: configuartion software configo ADx configurator PFS configurator maintenance programme Status indication for operation and serial communication standard USB connection galvanic isolation between TCS system and PC error detection and optical indication of overloads und under-voltage at input: under-voltage at a: below 18 V overload at a: as of 24,5 V under-voltage at P: below 15 V overload at P: as of 28 V detection of short-circuit and not supplied at M and at V1 and V2 FAX:+49 (0) 41 94/ Mail: hotline@tcsag.de PI_FBI1210_uk 1A mi

4 Patchkabel RJ /2013 I 2 C-Buchse für EEPROM-Platine von PES, PUK, PAK, TCU1, TCU2, AD3; ASI11000-EEPROM über Adapter anschließbar (im Lieferumfang) (EEPROMs von AD1, AD2 können nicht angeschlossen werden) Hörer für Sprechverbindung mit Innen- oder Außenstationen oder für Durchsagen in GFA-Anlagen System requirements PC Commissioning USB-Host-Interface, USB1.2 or USB2.0 standard Operating systems: Windows XP (as of SP2), Vista and Windows 7, Linux (Kernel with CDC Interface) Connection diagram Western jack not part of the delivery Patch cord RJ45 Assignment of connectors see table p. 5 FAX: +49 (0) 41 94/ Mail: hotline@tcsag.de PI_FBI1210_uk 1A mi

5 02/ Possible connections For frequent configuration works, the interface can be connected via a Western socket or an adapter board with the system (Patch cord RJ45 CAT.5e FTP, 2.0 m). V1, V2 and P are only connected to the FBI1210 for monitoring purposes. Connection assignment RJ45 jack, connector board Pin Description Pin Function Function Description 1 - Not used 5 P Voltage supply V DC 2 a 3 b Polartity-free 2-wire connection for protocol transfer Polartity-free 2-wire connection for protocol transfer 6 M Video ground 7 V1 Differential video input 4 - Not used 8 V2 Differential video input The connector board also features two 4-pin jacks for connecting a bell button extension as well as a 6-pin screw terminal to connect a cable provided by customer. EEPROM connection Via the I 2 C interface, the following memories can be read-out or written to without a TCS:BUS must be connected: EEPROM board (A) of PES, PUK, PAK, TCU1, TCU2 ASI11000-EEPROM (B) can be connected via adapter (enclosed in the delivery) SPI-EEPROMs (AD1 and AD2) cannot be connected. Put the EEPROM board into the I 2 C jack A: on the underside there are the structural elements B: on the upper side of the board conducting paths and structural elements of the ASI-EEPROM. Note: This pin header is coated and does not allow a staggered plugging of the EEPROM board. If the pin header is accidentally turned by 180, neither the EEPROM nor the FBI1210 will be damaged. A B Handset connection If a handset is connected to the device, by using suitable software e.g. TCS:BUS monitor, voice connections from the FBI1210 to indoor and front-door stations can be established. In GFA systems, announcements can be made to suitable indoor stations. For this, connect the handset to the RJ11 jack. FAX:+49 (0) 41 94/ Mail: hotline@tcsag.de PI_FBI1210_uk 1A mi

6 6 02/2013 Important notes The device supports the operating systems Windows XP (as of SP2), Vista and Windows7, Linux (Kernel with CDC Interface) and MacOS X. To operate the FBI1210, a system driver is absolutely necessary. If no driver has been installed, the interface does not work. Even if the respective TCS software has been installed on the PC. The USB interface is supported as of operating system Windows 98 SE. Older Windows versions (e.g. Win95 or Win98) are not suitable for the FBI1210. The FBI1210 can be operated with USB1.1 and USB2.0 interfaces. The USB cable must not be longer than 2 m.! When connecting the FBI1200 for the first time, it may only be connected when the PC is already booted. Installing the driver 1. Start Windows on your PC. 3. Download the latest driver for the virtual COM interface. (on our homepage > downloads > software > driver for FBI1200: 2. Start the setup file. The driver and the virtual COM interface are installed. Please wait until Console (ill.) is closed again. 3. Connect the FBI1210 using the USB cable to the USB interface of your PC according to the connection diagram (see p. 2). 6. Connect the FBI1210 to the TCS:BUS using the BUS connection cable (see p. 4). FAX: +49 (0) 41 94/ Mail: hotline@tcsag.de PI_FBI1210_uk 1A mi

7 02/ Technical data supply voltage: via USB connection from PC housing: plastics dimension FBI1210 (in mm): H 42 x W 90 x D 25 weight 45 g acceptable ambient temperature: 0 C to 40 C input current, standby: I(a) = 0.4 ma, I(P) = 2.0 ma max. input current: I(Pmax) = 2.0 ma FAQ Error pattern Possible cause Our solution The FBI1210 is not recognised at the PC. The virtual COM-port-driver to the FBI1200 cannot manage all Bluetooth communication connections. 1. Open Windows control panel, System, tab Hardware, open device manager. 2. Open connections, right mouse click on Bluetooth communication connection (COMx), deactivate. Conformity Conformity declaration can be downloaded from downloads, trade information. Waste disposal The adjoining symbol shows, that the device has to be disposed separately from domestic waste. The used materials are recyclable. Please do help protecting our environment and dispose the device via a colection point for electronic scrap. Dispose the parts of the packaging in collecting tanks for cardboard and paper resp. plastics. FAX:+49 (0) 41 94/ Mail: hotline@tcsag.de PI_FBI1210_uk 1A mi

8 8 02/2013 Warranty We offer a simplified processing in case of warranty for electricians. Note our conditions of sale and delivery, download from downloads, trade information and included in our latest price list. Please contact us: hotline@tcsag.de Service Please send your questions and inquiries to hotline@tcsag.de Headquarters TCS TürControlSysteme AG, Geschwister-Scholl-Str. 7, Genthin Tel.: /879910, FAX: /879911, Mail: info@ tcs-germany.de, FAX: +49 (0) 41 94/ Mail: hotline@tcsag.de PI_FBI1210_uk 1A mi