Getting Your Multifunction Back On Your Network After A Router Or Network Change

Size: px

Start display at page:

Download "Getting Your Multifunction Back On Your Network After A Router Or Network Change"

Tiffany Hudson
6 years ago
Views:

1 Getting Your Multifunction Back On Your Network After A Router Or Network Change PIXMA MG6320 Windows OS 1

2 Information Important If any of the following situations exist You have replaced your Router or Access Point You want to use a different wireless network Router settings have been changed. Please complete the following steps to apply the new configuration settings to your multifunction. 2

Preparing to Connect My Multifunction To My Network Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is

3 Preparing to Connect My Multifunction To My Network Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Wireless Connection Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that configuration of the computer and access point or router is complete. 3

Preparing to Connect My Multifunction To My Network An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not

4 Preparing to Connect My Multifunction To My Network An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. A wireless access point or router is required to use your printer on a wireless LAN. Notes on Network Connection The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer. In an office setup, consult your network administrator If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party. If an error message appears or if you have trouble with the network connection, refer to the printed manual: Network Setup Troubleshooting. Place the machine and computer on the same network segment. 4

5 Installing the Drivers & Software Software Installation To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application software to be installed.) IMPORTANT Log on as the administrator (or a member of the Administrators group). Quit all running applications before installation. Do not switch users during the installation process. Internet connection may be required during the installation. Connection fees may apply. Consult the internet service provider. It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the Setup CD-ROM during restarting. The installation resumes once your computer has restarted. If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access. 5

Connecting to the Wireless Network Installing the PIXMA MG6320 on Your Wireless Network When you reinstall your printer on your network because of a router or network change, you follow the same

6 Connecting to the Wireless Network Installing the PIXMA MG6320 on Your Wireless Network When you reinstall your printer on your network because of a router or network change, you follow the same procedure as for a first time install. A step-by-step walk through of the wireless setup is built in to the installation routine of the software that shipped with your PIXMA. Insert the Setup CD-ROM * that came with your printer into your CD-ROM drive and proceed through the easy to follow instructions If the following screen appears, click Start Setup Again * If you do not have the Setup CD-ROM you can still Install the printer using the download file available on our web site. Click Here for information. 6

7 Connecting to the Wireless Network Installing the PIXMA MG6320 on Your Wireless Network Continue to follow on-screen instructions. Be sure to select Wireless Connection on the Connection Method Selection screen (1-2). Continue to follow instructions until the Setup Procedure Selection screen (3-1)appears. This is shown on the next page 7

8 Connecting to the Wireless Network The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*. *Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the Stop button on the printer s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown below)*. If the Push Button Method is not shown on the printer s operation panel(when no WPS access points have been detected), select Standard setup on the printers operation panel, then click Other Methods on the Setup Procedure Selection screen If you selected the Push Button Method, follow any remaining instructions to complete setup. Click here to skip to software installation If you selected Other Methods, please continue to the next page for important information 8

9 Connecting to the Wireless Network For Standard setup only Select Standard setup on the Setup Procedure Selection screen (3-2) Follow the instruction then click Next on the Connection via Standard setup (4-1) screen. Continue to next page before proceeding any further with setup 9

information* Step 4-2 Step 4-4 *Unless you are absolutely certain of this information, please continue to the next

10 Connecting to the Wireless Network Follow On-screen instructions. When you get to Step 4-2 and later in Step 4-4 ( screens shown below) you will need to know SSID and password information* Step 4-2 Step 4-4 *Unless you are absolutely certain of this information, please continue to the next page for information on locating / verifying this information Continue to follow the on-screen instructions. Click Next when the Completion of Connection screen (4-7) appears. 10

Connecting to the Wireless Network If you don't know your Access Point / Router name or SSID*, or the Passphrase or Network key for your wireless network, you can find this information during

11 Connecting to the Wireless Network If you don't know your Access Point / Router name or SSID*, or the Passphrase or Network key for your wireless network, you can find this information during Standard setup using the Setup CD-ROM or the downloaded file (Mini Master Setup). *The terms 'SSID' and 'AccessPoint / Router' refer to a name used to identify the specific Access Point or Router. "Passphrase' and 'Network Key' refer to a password required to prevent unauthorized access to communication. Look for the Confirm the access point name or the Confirm the network key (automatic display) buttons during the setup procedure. Clicking either of these buttons will give the needed information. On a Mac OS X system you may need to click 'Allow' on one or more windows after clicking either of the above buttons. See example below of the Wireless Lan Setup Information window. (appearance varies depending on Operating System). Use the provided information when selecting the Access Point / Router and for entering the Network Key (Steps 4-2 and 4-4 on the previous page). 11

12 Installing the Drivers & Software Network setup is complete. Continue to follow any remaining On-screen instructions to install the software. On the Software Installation List screen, select any software to be installed. MP Drivers is required for the printer to be able to print and scan and cannot be de-selected. MY Image Garden and Quick Menu* are highly recommended to take full advantage of your printer s features. *Note: If you are using the downloaded Mini Master Setup file, only the MP Drivers will be installed. You can download the additional software applications from the Software section of the Drivers & Software page where you obtained the Mini Master setup file. 12

13 Installing the Drivers & Software Click Complete when the Setup Completion screen appears. Continue to follow any remaining on-screen instructions to finish and exit the setup program 13

Installing the Drivers & Software << Previous Installing the PIXMA MG6320 on Your Wireless Network If you can t find your CD-ROM, you may download the MG6300 series Mini Master Setup, which includes

14 Installing the Drivers & Software << Previous Installing the PIXMA MG6320 on Your Wireless Network If you can t find your CD-ROM, you may download the MG6300 series Mini Master Setup, which includes the same step-by-step installation as the CD-ROM, by following the instructions below: 1. Click here to access the MG6320 Drivers & Software page. 2. Select the operating system and version of your computer (see example below). 3. Expand the Drivers section, if necessary, by clicking the red triangle. 4. Click on MG6300 series Mini Master Setup. 5. After reading the details and disclaimer, click I Agree Begin Download and save the file to your computer. 6. Once the download is complete, double-click the file from its download location to begin the installation. Return to Setup instructions 14

Installing Your Multifunction to Your Network for the First Time

Installing Your Multifunction to Your Network for the First Time PIXMA MX722 Windows OS 1 Installing Your Multifunction to Your Network for the First Time PIXMA MX722 Windows OS Preparing to Connect My