XC300 VDSL Network Extender Owners Manual

Transcription

1 XC300 VDSL Network Extender Owners Manual

2 Warranty GDI Communications LLC warrants to the original consumer purchaser that each of its hardware products, and all components thereof, will be free from defects in materials and/or workmanship for one (1) year from the date of original purchase and is not assignable. In the event of malfunction or other indications of failure attributed directly to faulty workmanship and/or materials, GDI Communications LLC will, at its option, repair or replace the defective products or components to whatever extent it shall deem necessary to restore the product or components to proper operating condition, provided the consumer purchaser sends with the defective product proof of the date of purchase of the product. Please note that GDI Communications LLC may replace the defective product with a new or re manufactured functionally equivalent product of equal value at the option of GDI Communications LLC. The customer shall be solely responsible for the failure of any GDI Communications LLC computer product, or component thereof, resulting from accident, abuse, or misapplication of the product, and GDI Communications LLC assumes no liability as a consequence of such events under the terms of this Warranty. GDI Communications LLC does not warrant the merchantability or fitness of this product for any particular purpose. This limited warranty is in lieu of any and all other warranties, expressed or implied. GDI Communications LLC's liability shall not exceed the price of the defective individual product, which is the basis for claim. In no event will GDI Communications LLC be liable for direct, indirect, incidental, or consequential damages resulting from any defect in the product or in this manual, even if they have been advised of the possibility of such damages. In no event shall GDI Communications LLC be liable for any loss of profits, loss of equipment or facilities, or the loss of programs or data, or the cost of recovering or reproducing the program or data. Some states do not allow the exclusions or limitation of implied warranties or liability for incidental or consequential damages, so the above limitations or exclusion may not apply to you. 2

3 TABLE OF CONTENTS GENERAL INFORMATION.4 FEATURES.4 APPLICATIONS....5 INSTALLATION..7 CONNECTING TO THE VDSL LINE INTERFACE..8 CONNECTING THE LAN (ETHERNET) INTERFACE...9 CONNECTING THE TELEPHONE (POTS/ISDN) LINE...11 CONNECTING POWER...11 OPERATION POWER UP FRONT PANEL LED STATUS MONITORS CUSTOMER SERVICE SERVICE AND UNRESOLVED PROBLEMS APPENDIX A...15 SPECIFICATIONS APPENDIX B FACTORY REPLACEMENT PARTS AND ACCESSORIES..17 APPENDIX C INTERFACE PIN ASSIGNMENT

4 GENERAL INFORMATION Thank you for purchasing this GDI Communications LLC product. The XC300 is the perfect way to connect disparate Local Area Networks (LAN). There is no special wiring or special networking knowledge required. Using inexpensive, twisted copper pair wire the XC300 allows you to connect LANs that are separated by up to 4000ft, breaking the 300ft Ethernet barrier. The XC300 provides reliable high-speed data communication in the harshest operating environments. It can operate in uncontrolled environments such as remote terminals or curb side distribution vaults. Designed to operate in the harshest environments the XC300 has an operating temperature range of -40 C to +65 C, in non-condensing humidity of up to 95%. It can be set up at altitudes of up to 10,000 feet. The XC300NT and XC300LT work together to create a transparent extension between two Ethernet LANs. POTS/ISDN calls can be made over the VDSL link without interfering with the data. This manual has been designed to enable you to install your XC300 extender by following the step-by-step installation procedure. Follow the step-by-step installation instructions outlined in Section titled - Installation. FEATURES Easy to install standalone VDSL modems no configuration required Environmentally hardened for operation in harsh environments Auto-sensing full or half-duplex Ethernet Auto-sensing 10/100 operation Extends network connections up to 4,000 ft (1,219 m) over 2-wire 24-AWG unconditioned lines.7 to 26 Mbps symmetric and asymmetric line rate Internal POTS/ISDN splitter on board Transparent operation LED indicators for Power, Ethernet Link & Activity, VDSL Sync Surge suppression up to 20 ka Available in rack-mount or standalone configurations 4

5 APPLICATIONS The GDI Communications LLC XC300 set provides high-speed LAN connections between Ethernet LANs, remote PC s, or any other network enabled 10/100BaseT/TX device. Operating in pairs with an XC300NT located at one end of the LAN extension and an XC300LT at the other end. The data is passed transparently through the XC300 such that the remote LAN appears to be co-located with local network. Figure 1 shows a typical point-to-point application. The XC300 is well suited to surveillance applications where cameras with digital output are placed in strategic locations to observe any activity within view of the camera. The information from the camera can be transmitted to a central collection point up to 4000 ft away from the camera over inexpensive copper wire. Having the ability to pass voice communications simultaneously with the high-speed data allows camera positioning information to be sent without interfering with the data signal. Figure 2 shows a camera application 5

6 The XC300 is ideal for building riser applications where distribution of high-speed data communications in a multi-story building is required. Ordinary communications equipment is inefficient in this high noise environment. The alternative is to use fiber optic cable that is expensive; the end-to-end equipment is also expensive. The XC300 is well suited for this environment. Designed with robust VDSL technology the XC300 can deliver reliable high-speed communications throughout the multi-story building at a fraction of the cost of the fiber optic solution. 6

7 INSTALLATION Because the XC300 requires no configuration, it can be installed and made operational quickly. Installation takes place as follows 1. Connecting the VDSL line interface between the units (refer to section titled, Connecting the VDSL Line Interface on page 8) See Figure 4 for the rear panel connector arrangements. 2. Connecting the Ethernet interface (refer to section titled, Connecting the LAN (10/100Base-T) Ethernet Interface on page 9). 3. Connecting the POTS to a telephone or telephone line (refer to the section titled Connecting the POTS/ISDN line on page 11) 4. Connecting the power plug (refer to section titled, Connecting Power on page 11). XC300 7

8 CONNECTING TO THE VDSL LINE INTERFACE The XC300 supports communication between two Ethernet LAN sites over a distance of up to 4,000 ft (1,219 m) over 24 AWG (0.5 mm) twisted-pair wire. Actual distance and link performance may vary depending on the environment and type or gauge of wire used. Follow the steps below to connect the XC300 VDSL Interfaces. The XC300 is a pair of units. One of the units must be an XC300NT, and the other unit must be an XC300LT. It does not matter which end is the XC300NT and which is the XC300LT. The XC300LT always initiates the link. As long as the XC300NT is powered on, the XC300LT can establish a link by being powered ON or by a power reset. To function properly, the units must be connected together using twisted-pair, unconditioned, metal wire, between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable. The interface is bipolar making the TIP and RING connection non-critical. XC300(RJ11) VDSL Line Interface 8

9 CONNECTING THE LAN (ETHERNET) INTERFACE The RJ-45 port labeled LAN is the 10/100BaseT/TX interface. This port is designed to connect directly to a 10/100BaseT/TX network. Figures 6 & 7 show the signal/pin relationships on this interface. You may connect this port to another Ethernet device via a Cat 3 or Cat 5 cable that is up to 328 ft long. TX+ (data output from XC300) TX- (data output from XC300) RX+ (data input to XC300) (No Connection) (No Connection) RX- (data input to XC300) (No Connection) (No Connection) XC300NT LAN (10/100BaseT/TX) RJ45 Connector Pin-out RX+ (data input to XC300) RX- (data input to XC300) TX+ (data output from XC300) (No Connection) (No Connection) TX- (data output from XC300) (No Connection) (No Connection) XC300LT LAN (10/100BaseT/TX) RJ45 Connector Pin-out Connecting the LAN (10/100BaseT/TX) Ethernet Port to a Hub The XC300NT 10/100BaseT/TX interface is configured as DTE (Data Terminal Equipment), just like a 10/100BaseT/TX network interface card in a PC. Therefore, it "expects" to connect to a DCE (Data Communications Equipment) device such as a Hub. This typically uses a straight-through cable. The Figure 8 diagram shows the cable wiring for connecting the XC300NT to a 10/100BaseT/TX hub. 9

10 The XC300LT 10/100BaseT/TX interface is configured as DCE (Data Communications Equipment), just like a 10/100BaseT/TX network hub. Therefore, it "expects" to connect to a DTE (Data Terminal Equipment) device such as a PC. This typically uses a crossover cable. The Figure 9 diagram shows the cable wiring for connecting the XC300LT to a 10/100BaseT/TX hub. XC300NT LAN (10/100BaseT/TX) Port 10/100BaseT/TX Hub Figure 8. 10/100BaseT/TX straight through cable Connecting the LAN (10/100BaseT/TX) Ethernet Port to a PC (DTE) The XC300 LAN (10/100Base-T) interface is configured as DTE (Data Terminal Equipment). If you wish to connect the XC300 to another DTE device such as network interface card (NIC) in a PC (or XC300 in a back-to-back arrangement), you must use a crossover cable as shown in Figure 9. XC300LT LAN (10/100BaseT/TX) Port 10/100BaseT/TX Figure 9. 10/100BaseT/TX crossover cable NOTE: When connecting to a 10/100BaseT/TX Switch that is equipped with crossover detection it is not necessary to use a crossover cable from the XC300LT to the switch. The need to crossover will be automatically detected within the switch and the connection will be made. 10

11 CONNECTING THE TELEPHONE (POTS/ISDN) LINE The RJ 11 port labeled PHONE is the TELEPHONE or POTS/ISDN interface. A telephone or an ISDN device may be connected to this port and carried over the VDSL line. The XC300 does not need to be powered ON for the POTS interface to work. The RJ 11 connector in the XC300 PHONE interface is wired as shown in Figure 10. Figure 10. XC300 PHONE (RJ 11, POTS/ISDN) interface CONNECTING POWER An external AC cube style power supply is available. Power to the XC300 is connected using the barrel jack on the rear panel. No configuration is necessary for the power supply. DC power supplied must meet the following requirements; DC power must be regulated +5VDC ±5%, 1.0A minimum. Center pin is +5V. The barrel type plug has a 2.5/5.5/10mm I.D./O.D./Shaft Length dimensions. The XC300 does not have a power switch, it powers up as soon as it is plugged in. 11

12 OPERATION Once the XC300 is properly installed, the set should operate transparently. No user settings are required. This section describes the LED status monitors. POWER UP Before applying power to the XC300, please review section titled, Connecting Power to verify that the unit is connected to the appropriate power source. FRONT PANEL LED STATUS MONITORS The XC300 features four front panel LEDs that monitor power, the Ethernet signals, and the VDSL Connection. Figure 11 shows the front panel location of each LED. Table 1 describes the LED functions. XC300 Figure 11 XC300 Front Panel LED location 12

13 LED Description LED Power VDSL Sync Ethernet Good Link Ethernet Activity Indication Solid GREEN to indicate the unit is powered ON. (Active Green) Solid green (ON) to indicate that the end-to end VDSL link between the XC300 set is established. The VDSL LED is OFF when the link is down. (Active Green) Solid Green indicates that Ethernet link has been established. (Active Yellow) Flashes to indicate Ethernet activity on the 10/100Base-T Ethernet port. Table 1: Front Panel LED Description 13

14 CUSTOMER SERVICE SERVICE AND UNRESOLVED PROBLEMS For assistance, phone GDI Communications LLC s Customer Service Department between 7:00 A.M. and 3:30 P.M. Pacific Time at (775) or FAX (775) When calling for assistance try to do so from the installation site, we have a better chance to successfully troubleshoot your installation and getting your installation up and running. Before returning a product for repair, you must call GDI Communications LLC s Customer Service Department and receive a Returned Material Authorization (RMA) number. This number must appear on the outside of the shipping container with the address as indicated below. Products should be returned to: GDI COMMUNICATIONS LLC, INC 280 I-80 West Exit 1 Verdi, NV Attention: Customer Service-RMA # To ensure accurate return of repaired/replaced product, please enclose a note with the returned item; with your name, company name, mailing address, telephone number, RMA number and any special instructions. During the first year after the date of purchase, all labor and materials will be provided without charge. There shall be no warranty for either parts or labor after the expiration of one year from the date of purchase or if in GDI Communications LLC s sole discretion the product has been deemed to be modified or abused. Units must be returned postage prepaid, CODs will not be accepted! It is recommended that the unit be insured when shipped. Units returned without proof of date-of-purchase or out-of-warranty units will be repaired or replaced (at the option of GDI Communications LLC) and a charge will be made for parts and labor. Products repaired/replaced under warranty will be returned to any destination within the USA at GDI Communications LLC s expense. The carrier and method of shipment will be determined by GDI Communications LLC. If the customer requests a specific form of conveyance or is located beyond the USA borders or if the unit is out-of-warranty, all shipping costs will be incurred by the customer. 14

15 APPENDIX A SPECIFICATIONS CONNECTORS LAN: Shielded or Unshielded RJ-45, 10/100Base-T, IEEE Ethernet VDSL: RJ 11 PHONE (POTS): RJ 11 VDSL ENVIRONMENT LINE: 19 to 26 AWG (0.5 mm) twisted-pair wire LINE RATE: 1 to 25 Mbps, symmetric or asymmetric DISTANCE: Up to 4,000 ft (1,219 m) LED INDICATORS Power (Green) VDSL Sync (Green) Ethernet Good Link (Green) Ethernet Activity (Yellow) POWER SUPPLY External AC power cube 90 to 240 VAC, 47 to 63Hz, 2 Watt OPERATING ENVIRONMENT TEMPERATURE RANGE: -40 C to +65 C HUMIDITY: Up to 95% non-condensing DIMENSIONS 1.5H x 3.8W x 5.0D in. (3.8H x 9.6W x 12.6D cm) MOUNTING Metal enclosure with wallmount tabs. Rubber feet for table mount. 15

16 APPROVALS FCC NOTICE The XC300 generates and uses radio frequency energy, and if not properly installed and used in strict accordance with the manufacturer s instructions it may cause interference to radio and television reception. The XC300 has been tested and found to comply with Class A computing device in accordance with specifications in Subpart B of Part 15 of FCC rules. However, there is no guarantee that interference will not occur in a particular installation. 16

17 APPENDIX B FACTORY REPLACEMENT PARTS AND ACCESSORIES GDI Communications LLC Model Description Model XC300LT XC300NT XC300 NTPS Description VDSL Modem, voice & data VDSL Modem, voice & data VDSL MODEM SET, Kit: includes one XC300LT and one XC300NT, voice & data, VAC (+5V reg. DC/1A) Universal Input Adapter. 17

18 APPENDIX C INTERFACE PIN ASSIGNMENT LAN (ETHERNET 10/100BASET/TX) INTERFACE: RJ-45 UTP/STP VDSL LINE INTERFACE: RJ-11 PHONE (POTS/ISDN) INTERFACE: RJ-11 POWER JACK Center pin: regulated +5VDC ±5%, 1.0A minimum Outer ring: Common or Ground CONSOLE PLUG: FRONT PANEL ACCESS (for models equipped with front panel access) Pin 1: VCC Pin 2: TX Pin 3: RX Pin 4: GND CONSOLE CABLE WITH DB 9 PLUG: 18

19 Copyright 2003 GDI Communications LLC All Rights Reserved. 19