Commissioning. IT554 VPN Router

Transcription

1 Issue Datasheet EN VPN Router pplication is a VPN router with client functionality and customized software that enables the secure transfer of encrypted data between controllers and building management systems. It serves as a central firewall and VPN gateway for small-sized and medium-sized locations. Content Page Important Information Regarding Product Safety Preparatory steps...3 Connecting the Router...3 Installing Firmware on the VPN Router...3 Initial firmware installation of the VPN Router...4 Update of the VPN Router...5 Resetting the VPN Router...6 Connecting the Router On-Site...6 Änderungen vorbehalten - Contents subject to change - Sous réserve de modifications - Reservado el derecho a modificación - Wijzigingen voorbehouden - Con riserva di modifiche - Innehåll som skall ändras - Změny vyhrazeny - Zmiany zastrzeżone - Возможны изменения - változtatások jogát fenntartjuk - 保留未经通知而改动的权力 Kieback&Peter GmbH & Co. KG Tempelhofer Weg 50, Berlin/Germany Telefon: , Telefax: info@kieback-peter.com

2 Important Information Regarding Product Safety Safety Instructions This data sheet contains information on installing and commissioning the product "". Each person who carries out work on this product must have read and understood this data sheet. If you have any questions that are not resolved by this data sheet, you can obtain further information from the supplier or manufacturer. If the product is not used in accordance with this data sheet, the protection provided will be impaired. pplicable regulations must be observed when installing and using the device. Within the EU, these include regulations regarding occupational safety and accident prevention as well as those from the VDE (ssociation for Electrical, Electronic & Information Technologies). If the device is used in other countries, it is the responsibility of the system installer or operator to comply with local regulations. Mounting, installation and commissioning work on the devices may only be carried out by qualified technicians. Qualified technicians are persons who are familiar with the described product and who can assess given tasks and recognize possible dangers due to technical training, knowledge and experience as well as knowledge of the appropriate regulations. Legend WRNING Indicates a hazard of medium risk which can result in death or severe bodily injury if it is not avoided. CUTION Indicates a hazard of low risk which can result in minor or medium bodily injury if it is not avoided.! NOTICE Indicates a hazard of medium risk which can result in material damage or malfunctions if it is not avoided. Indicates additional information that can simplify the work with the product for you. Notes on Disposal For disposal, the product is considered waste from electrical and electronic equipment (electronic waste) and must not be disposed of as household waste. Special treatment for specific components may be legally binding or ecologically sensible. The local and currently applicable legislation must be observed. Page 2 / 8

3 Preparatory steps The router may only be configured by a qualified specialist. Changing the firmware and setting up an IP address within an existing network may render the computers in the network unable to establish a connection with each other. Before performing the tasks described below, you must successfully complete the Kieback&Peter online training course Network Technology 1 at To install the firmware, up-to-date firmware must be available for all VPN routers. Up-to-date firmware is created with the TechnoWay Configurator (see the TechnoWay Configurator user manual). Ensure that the Internet access router is configured to support a permanent Internet connection. Otherwise you may experience interruptions in the connection. Configuring port forwarding on the Internet access router For the VPN server: Port 1194/UDP must be forwarded to the WN IP of the VPN router on the Internet access router. To do this, contact the network administrator of the network in which the server is located. Make sure that none of the LN or WN networks conflict with any of the client WN networks distributed via DHCP. This could cause connection problems between the affected peers. Connecting the Router Unpack the router. Check the scope of delivery. Scope of delivery: 1x VPN router 1x power supply unit including power cable Connect: Connect the router to the LN port of the Windows PC with a patch cable.! NOTICE Damage to property can result from the use of non-original power supply units. Use only the original power supply unit. The router can be damaged if another power supply unit is used. Connect the VPN router to the power supply. The Power LED flashes during the startup procedure. Once the Power LED lights up steadily, the startup procedure is complete. Installing Firmware on the VPN Router Depending on the project, there are two different ways to update the firmware: Initial firmware installation: Initial installation of the Kieback&Peter firmware on a VPN router Updating existing firmware: Updating VPN routers when there are changes to the network configuration Page 3 / 8

4 Requirements For the initial installation of the firmware, you will need the BIN file from the generated ZIP file. (See the TechnoWay Configurator user manual.) The TRX file is used to update the firmware. (See the TechnoWay Configurator user manual.) Unpack the ZIP file. Initial firmware installation of the VPN Router Initial firmware installation During the initial firmware installation, the pre-installed firmware is replaced by the new firmware. Ensure that all routers have been labeled. Start the browser. Enter the IP address of the router in the address field of the browser: Press the ENTER key. The firmware starts and opens the logon dialog. Skip over the User name text box. It remains empty. Enter the password admin. Click the OK button. The start screen of the firmware is displayed. Select the dministration menu. Select the Update firmware menu. The selection dialog for the upgrade file is displayed. Click the Browse button. Select the BIN file. Click the Update button. The firmware installation is carried out. In the Update successful window, do not click the button Continue. Since the IP address of the VPN router was changed by the installation, this results in a browser error message. Restarting the VPN router fter successful installation, the router restarts. The Power LED flashes during startup. The new IP address is activated. fter about two minutes, the restart is complete. When the Power LED stops flashing, the firmware is installed. Switch off the router for at least three seconds. lternatively, you can remove the network cable from the LN port. Switch on the router or insert the network cable back into the LN port. The computer recognizes the new IP address and establishes the connection to the router. Check the connection to the new IP address of the router by entering the IP address in the address field of the browser. Label the router with the configuration ID and LN IP. Page 4 / 8

5 ccess to a VPN router with unknown IP configuration If you do not know the IP address of the VPN router, use the following steps to import a valid firmware image. Use a patch cable to connect the LN port of the VPN router to a Windows PC. Configure the network interface of the PC to DHCP. The VPN router assigns network settings to the PC using DHCP. The gateway assigned to the PC corresponds to the IP address of the router. Connect to the VPN router using the browser. Carry out another update of the firmware (See chapter Updating the firmware after network changes, page 5.). Update of the VPN Router Updating the firmware after network changes Ensure that all routers have been labeled. Start the browser. Enter the IP address of the router in the address field of the browser. You can find the IP address on the router. Press the ENTER key. The firmware starts and opens the logon dialog. Enter the user name root. Enter the password in the corresponding Password text box according to the printed configuration overview. Click the Login button. The start screen of the firmware is displayed. Select the System menu. Select the Flash Firmware submenu. The selection dialog for the upgrade file is displayed. Click the Browse button. Select the TRX file. Deactivate the Keep configuration files checkbox so that the system settings from the TRX file are applied. Click the Upload image button. The screen displays an information window. Click the Proceed button to start the update of the firmware. Restarting the VPN router fter successful installation, the router restarts. The Power LED flashes during startup. The new IP address is activated. fter about two minutes, the restart is complete. When the Power LED stops flashing, the firmware is installed. Switch off the router for at least three seconds. lternatively, you can remove the network cable from the LN port. Switch on the router or plug the network cable back into the LN port. The computer recognizes the new IP address and establishes the connection to the router. Check the connection to the new IP address of the router by entering the IP address in the address field of the browser. Page 5 / 8

6 Update the label on the router. Resetting the VPN Router Resetting the VPN router You cannot reset the router yourself. Send in the router when a reset is necessary. Connecting the Router On-Site! NOTICE Before connecting the router to the broadband router, check the IP network distributed to this router via DHCP. Make sure that the IP network does not conflict with any other IP network in this TechnoWay configuration. If the IP network conflicts with another IP network, change this DHCP network on the broadband router to an available subnet. Connect the VPN router according to the following diagrams. Check the connection to the new IP address of the router by entering the IP address in the address field of the browser. Connection Internet: The Internet port (WN connection) is used to connect the Internet connection (broadband router). 2 1, 2, 3, 4: These Ethernet ports (LN connection) connect the router with PCs, the BMS or controllers. 3 Power: The power supply unit is connected to the power supply. Page 6 / 8

7 Connection Diagram LN Internet IT560 LN B Router VPN-Client VPN Router VPN-Server Status indicators Power 2 DMZ 3 Ethernet 4 Internet LEDs Status Description Power On/Off Lights up/flashes green Lights up green when the router is supplied with current. Flashes during startup when a self-diagnosis is being carried out. DMZ Lights up green Lights up green if the DMZ function is in use. Ethernet 1, 2, 3, 4 Internet Lights up/flashes green Lights up/flashes green When the relevant LED lights up steadily, the router is connected to a device on this port. When the relevant LED flashes, there is network activity on this port. Lights up green if a connection is established on the Internet port. When the relevant LED flashes, there is network activity on this port. Page 7 / 8

8 Page 8 / 8