QUICK INSTALLATION GUIDE. 4CH, 8CH & 16CH Surveillance System / NVR WiFi PoE Camera Kit

Transcription

1 QUICK INSTALLATION GUIDE 4CH, 8CH & 16CH Surveillance System / NVR WiFi PoE Camera Kit

2 WHAT S IN THE BOX 4CH NVR KIT 1 Four (4) 631H2 WiFi PoE IP Cameras S WiFi AP / Router 2 N8/1U 8 Channel IP NVR with 500GB Hard Drive 6 POE31004P 5-port PoE switch 3 Four (4) Antennas for Cameras 7 Four (4) power adapters for cameras 4 Software CDs for managing NVR & Cameras 8 Four (4) sets of mounting hardware for cameras

3 WHAT S IN THE BOX 8CH NVR KIT 1 Eight (8) 631H2 WiFi PoE IP Cameras S WiFi AP / Router 2 N8/1U 8 Channel IP NVR with 1TB Hard Drive 6 POE31008P 9-port PoE switch 3 Eight (8) Antennas for Cameras 7 Eight (8) power adapters for cameras 4 Software CDs for managing NVR & Cameras 8 Eight (8) sets of mounting hardware for cameras

4 WHAT S IN THE BOX 16CH NVR KIT 1 Sixteen (16) 631H2 WiFi PoE IP Cameras 5 TWO (2) 9508S WiFi AP / Routers 2 N25/1U 25 Channel IP NVR with 4TB Hard Drive 6 TWO (2) POE31008P 9-port PoE switches 3 Sixteen (16) Antennas for Cameras 7 Sixteen (16) power adapters for cameras 4 Software CDs for managing NVR & Cameras 8 Sixteen (16) sets of mounting hardware for cameras

5 9508S WIFI AP / ROUTER The 9508s is a 3-in-1 wireless device. It can be configured as a wireless router, Access-Point or Repeater. The 9508s is configured as an Access-Point by default to ensure it works with your home / business Wireless router without any issues. The WiFi cameras are pre-configured with the SSID & password of the 9508s. The WiFi cameras generate a lot of wireless video traffic which might slow down your existing wireless network. With the 9508s, the cameras are on a different wireless network and do not share your home / business wireless network. This will ensure that there is no load on your network from the IP cameras. The 9508s is configured with Channel 7. If you experience your wireless network to be sluggish after installing the NVR system, we recommend you to check the wireless channels settings on your wireless router and change it to either channel 1 or channel 11 so it does not overlap with channel 7. The cameras also supported wired connections. If you decide to go with wired installation and not use the WiFi feature, then you do not need to install the 9508s.

6 POE SWITCH A PoE switch is same as a regular Ethernet switch except that it also sends power over the same Ethernet cable, which is used to power the cameras. PoE switch can power a variety of devices such as wireless routers, IP phones, cameras, or any device that is PoE enabled. The included PoE switch (PoE3100Xp) can be used to connect the cameras using Ethernet cables. When the cameras are connected to the PoE switch, they are automatically powered through the Ethernet cable, which eliminates the need for using the power adapters to power the cameras. You can connect the cameras using Cat5e or Cat 6 Ethernet cable. The cable should be straight through will all 4 pairs terminated at both ends. Pairs 1,2 & 3,6 (data pairs) are used for video transmission and pairs 4,5 & 7,8 (spare pairs) are used to power the device. The maximum length of the cable cannot exceed 300ft (100 meters) for the PoE switch to efficiently power the cameras. The PoE switch can send full power of 15.4W per each port If you decide to use the cameras wirelessly, then you do not need to use the PoE switch. You can also use the PoE switch as a regular Ethernet switch to add more ports to your wireless router in case you are out of free ports. You can use the NVR system with both wired and wireless cameras, where some cameras can be connected wirelessly using the 9508s AP and some cameras can be connected over Ethernet cable using the PoE switch.

7 INSTALLING YOUR NVR SYSTEM WIFI CONNECTIVITY (9508s) The cameras can be connected either wired or wireless. If you are planning to use the cameras wirelessly, follow the below instructions 1 Connect the 9508S WiFi AP & the NVR to your Home / Business WiFi Router LAN Your Home / Business WiFi / Internet Router 2 Power on the Cameras WAN LAN 9508S WiFi AP HD 1080p TV or Monitor HDMI or VGA LAN 4CH / 8CH / 16CH NVR

8 INSTALLING YOUR NVR SYSTEM WIRED CONNECTIVITY (POE) The cameras can be connected either wired or wireless. If you are planning to connect the camera using Ethernet cable, follow the below instructions 1 Connect the 9508S WiFi AP & the NVR to your Home / Business WiFi Router LAN POE3100Xp 2 Your Home / Business WiFi / Internet Router Connect the cameras using Cat5e or Cat 6 Ethernet cables. HD 1080p TV or Monitor HDMI or VGA LAN 4CH / 8CH / 16CH NVR

9 REMOTE VIEW APP (GOOLINK) SETUP ON YOUR SMART PHONE 1 Install the GOOLINK FREE app on your iphone / Android phone 2 Start the app, click on + sign to add device & select QR Code Scan option. 3 Scan the QR code on the back of the NVR 4 The default username is Admin and leave the password blank. 5 Save the settings. And now you should be able to select the device you just added and watch the channels

10 NVR System IP Address & Access Information (4CH & 8CH NVR Systems) Device IP Address Username Password Admin GUI NVR admin (no password set) Camera admin admin Where x = 21 for cam1, 22 for cam2 and so on. 9508S WiFi Router admin admin

11 NVR System IP Address & Access Information (16CH NVR Systems) Device IP Address Username Password Admin GUI NVR admin (no password set) Camera admin admin Where x = 21 for cam1, 22 for cam2 and so on. 9508S -1 WiFi Router 9508S -1 WiFi Router admin admin admin admin

12 CAMERA GUIDE CAMERAS FEATURES 631H2 536H2 653H5 537H af (POE) n (WiFi) (2.4GHz) ONVIF 2.1 Compliant IP66 Weather Proof Lens 3.6mm Fixed Lens 3.6mm Fixed Lens Varifocal Lens (2.8mm 12mm) Varifocal Lens (2.8mm 12mm) Zoom Manual Manual CMOS Sensor 1/2.8 1/2.8 1/3 1/3 Resolution 1MP, 3MP, 3MP, Two-Way Audio Casing Aluminum Mini Bullet Plastic Dome Aluminum Bullet Plastic Dome IR Cut Night Vision IR Distance / LEDs 20M / 24 LEDs 20M / 24 LEDs 40M / 36 LEDs 40M / 36 LEDs Partial Occlusion WDR Motion Detection Privacy Masking Auto Iris P2P Cloud Web Admin GUI