Cisco 7609 Router and Cisco 7609-S Router Fan Assembly. Captive installation screw OC12 POS MM WS-C6500-SFM WS-C6500-SFM SWITCH FABRIC MDL

Transcription

1 LINK LINK LINK INPUT FAN OK OK SWITCH FABRIC MDL FAIL ACTIVE WS-C6500-SFM WS-C6500-SFM SWITCH FABRIC MDL ACTIVE 2 LINK 1 ACTIVE PORT 2 CARRIER ALARM PORT 3 1% CONSOLE 1% CONSOLE LINK ACTIVE PORT 2 PORT 3 LINK LINK CARRIER ALARM ACTIVE PORT 2 PORT 3 LINK LINK LINK INPUT FAN OK OK FAIL Removing and Replacing the Fan Assembly Chapter 5 Removal and Replacement Procedures Figure Cisco 7609 Router and Cisco 7609-S Router Fan Assembly Captive installation screw OSM-8OC3-POS MM 8 PORT OC3 POS MM 8 PORT OC3 POS MM STATUS LINK OSM-8OC3-POS MM STATUS LINK OSM-40C12-POS-MM OC12 POS MM STATUS LINK 1 STATUS STATUS OC12 POS MM STATUS OSM-40C12-POS-MM OC12 POS MM STATUS OSM-40C12-POS-MM SUPERVISOR2 STATUS SYSTEM WS-X6K-SUP2-2GE SUPERVISOR2 STATUS SYSTEM WS-X6K-SUP2-2GE LINK 1 PWR MGMT RESET PWR MGMT RESET LINK LINK LINK 3 LINK 4 LINK 2 LINK 3 LINK 2 LINK 3 CONSOLE CONSOLE PORT MODE CONSOLE CONSOLE PORT MODE Captive installation screw LINK RESET LINK CARRIER ALARM LINK RESET LINK CARRIER ALARM RESET CARRIER ALARM PORT 1 CARRIER ALARM ACTIVE LINK 4 RESET CARRIER ALARM PORT 1 CARRIER ALARM ACTIVE LINK 4 RESET CARRIER ALARM PORT 1 ACTIVE PCMCIA EJECT PCMCIA EJECT CARRIER ALARM ACTIVE NEXT SELECT NEXT SELECT CARRIER ALARM ACTIVE CARRIER ALARM ACTIVE Switch Load 100% Switch Load 100% CARRIER ALARM ACTIVE CARRIER ALARM ACTIVE CARRIER ALARM ACTIVE PORT 1 PORT 2 PORT 1 PORT 2 o o OUTPUT OUTPUT 5-124

2 Chapter 5 Removal and Replacement Procedures Removing and Replacing the Fan Assembly Step 3 Grasp the fan assembly with both hands and pull it outward; rock it gently if necessary to unseat the power connector from the backplane. Warning Step 4 When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the fan blades completely stop before you remove the fan tray. Pull the fan assembly clear of the chassis, and put it in a safe place. Installing the Fan Assembly Perform these steps to install the new fan assembly: Step 1 Step 2 Step 3 Step 4 Hold the fan assembly with the fans facing to the right and the FAN STATUS LED at the bottom (see Figure for the Cisco 7603 router, Figure for the Cisco 7603 router, Figure for the Cisco 7604 router, Figure for Cisco 7606 router, Figure for Cisco 7606-S router, and Figure for the Cisco 7613 router.) For the Cisco 7609 router and the Cisco 7609-S router, hold the fan assembly so that the handle is at the top of the assembly (see Figure 5-124). Place the fan assembly into the front chassis cavity so that it rests on the chassis, and then lift the fan assembly up slightly, aligning the top and bottom chassis guides. Push the fan assembly into the chassis until the power connector seats in the backplane and the captive installation screws make contact with the chassis. Tighten the captive installation screws. Note On the Cisco 7609 router and the Cisco 7609-S router, fold the cable guide up and tighten the two captive installation screws at the top of the chassis (see Figure 5-123)

3 ES20-10G3CXL ETHERNET SERVICES MODULE 7600-ES20-10G3CXL ETHERNET SERVICES MODULE 7600-ES20-10G3CXL ETHERNET SERVICES MODULE CLASS 1 LASER CLASS 1 LASER CLASS 1 LASER CLASS 1 LASER Cisco THERM-T606S Installing the Air Filter Assembly on a Cisco 7606 Router and the Cisco 7606-S Router (Optional) Chapter 5 Removal and Replacement Procedures Checking the Installation Perform these steps when checking the installation to verify that the new fan assembly is installed correctly: Step 1 Step 2 Step 3 Listen for the fans; you should immediately hear them operating. If you do not hear them, ensure that the fan assembly is inserted completely in the chassis and the faceplate is flush with the switch back panel. Verify that the FAN STATUS LED is green. If the LED is red, one or more fans is faulty. If after several attempts the fans do not operate or you experience trouble with the installation (for instance, if the captive installation screws do not align with the chassis holes), contact a Cisco customer service representative for assistance. Installing the Air Filter Assembly on a Cisco 7606 Router and the Cisco 7606-S Router (Optional) This section describes how to install the optional air filter assembly (CVPN7600FIPS/KIT=) for the Cisco 7606 and Cisco 7606-S routers. Perform these steps to install the new filter assembly. Step 1 Install filter assembly using thumscrews (see Figure 5-125). Enage thumbscrews only halfway. Figure Cisco 7606 and Cisco 7606-S Router Filter Assembly 1 FAN STATUS A/L STATUS ETHERNET SERVICES MODULE 7600-ES20-10G3CXL STATUS A/L A/L 2 A/L A/L STATUS A/L A/L STATUS STATUS A/L

4 Chapter 5 Removal and Replacement Procedures Installing the Air Filter Assembly on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) 1 Filter 3 Plastic rivets 2 Thumbscrews 4 Plastic fastener Step 2 Step 3 Insert plastic rivet through filter assembly into ventilation holes on chassis as shown. While holding the filter assembly and inserted rivet in place, insert the plastic fastener to the rivet. Fully secure the thumscrews. Installing the Air Filter Assembly on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) This section describes how to install the optional air filter assembly for the Cisco 7609 router and the Cisco 7609-S router. The filter assembly is not included with the chassis or bundle configurations. The necessary parts can be ordered at listed in Table 5-1. The filter assembly installation requires INTAKEPNL-09= be installed on the chassis. This intake panel can be identified by the two filter assembly support loops extending from the bottom front of the panel and the thumbscrews of the front left and right sides of the panel (see Figure 5-127). Note The use of air filter assembly provides the convenience of intake panel maintenance. The disposable form air filter fits on the intake panel and prevents dust, dirt and other impurities from entering the panel. You can replace the air filter when it wears out. The air filter should be used for intake panels in environments where settling of dust particles on intake panel is high. Note If you are replacing an air filter and not installing a new air filter assembly, see Replacing the Air Filter on a Cisco 7609 Router and the Cisco 7609-S Router (Optional), page Table 5-1 Air Filter Part Numbers Part Number INTAKEPNL-09= FLTRASSM-09= FLTRINSERTS-09= Description Replacement Intake Panel Filter Cage Assembly, no filter inserts included Set of five replacement air filter inserts for FLTRASSM-09= Perform these steps to install the new filter assembly. If INTAKEPNL-09= is already installed, skip to Step 3. Step 1 Remove the intake panel by unscrewing four thumbscrews (see Figure 5-126)

5 ACTIVE ACTIVE ACTIVE ACTIVE Installing the Air Filter Assembly on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) Chapter 5 Removal and Replacement Procedures Figure Removing the Intake Panel LINK PORT 2 PORT 2 o o INPUT FAN OUTPUT OK OK FAIL INPUT FAN OUTPUT OK OK FAIL Step 2 Install the new intake panel (see Figure 5-127) by tightening four thumbscrews. Figure Installing the New Intake Panel LINK PORT 2 PORT 2 o o INPUT FAN OUTPUT OK OK FAIL INPUT FAN OUTPUT OK OK FAIL Thumbscrews 2 Fastening screw 3 Support loop 5-128

6 Chapter 5 Removal and Replacement Procedures Installing the Air Filter Assembly on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) Step 3 Remove the inner filter retainer from the filter cage assembly (see Figure 5-128) by depressing the thumb loops and carefully sliding filter retainer outwards. Figure Removing the Inner Filter Retainer Filter cage assembly 2 Filter retainer 3 Thumb loops 4 Tabs (on rear of filter cage assembly) Step 4 Place the foam filter over the filter retainer (see Figure 5-129). Step 5 Slide retainer and filter into cage assembly

7 Installing the Air Filter Assembly on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) Chapter 5 Removal and Replacement Procedures Figure Placing the Foam Filter Over the Filter Retainer Filter cage assembly 2 Filter 3 Filter retainer 4 Tabs (on rear of filter cage assembly) 5 Thumb loops Step 6 Install filter assembly with tabs facing the floor as follows: a. Fit tabs (see Figure 5-129) on bottom of filter cage assembly into lower support loops (see Figure 5-127). b. Rotate the filter assembly towards the intake panel (see Figure 5-130). c. Tighten two fastening screws

8 ACTIVE ACTIVE Chapter 5 Removal and Replacement Procedures Replacing the Air Filter on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) Figure Installing the Filter Assembly LINK PORT 2 PORT 2 o o INPUT FAN OUTPUT OK OK FAIL INPUT FAN OUTPUT OK OK FAIL Thumbscrews 2 Fastening screw Note Cisco Systems recommends that air filters be changed every three months. Replacing the Air Filter on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) Step 1 Step 2 Loosen the two fastening screws as shown in Figure and lift the filter cage assembly off of the support loops (see Figure 5-127). Remove the inner filter retainer from the filter cage assembly (see Figure 5-131) by depressing the thumb loops and carefully sliding filter retainer outwards

9 Cleaning or Replacing the Chassis Air Filter and Intake Panel Chapter 5 Removal and Replacement Procedures Figure Replacing the Foam Filter on the Filter Retainer Filter cage assembly 2 Filter 3 Filter retainer 4 Tabs (on rear of filter cage assembly) 5 Thumb loops Step 3 Remove the foam filter and place a new foam filter over the filter retainer (see Figure 5-131). Step 4 Step 5 Slide retainer and filter into cage assembly. Install filter assembly with tabs facing the floor as follows: a. Fit tabs (see Figure 5-129) on bottom of filter cage assembly into lower support loops (see Figure 5-127). b. Rotate the filter assembly towards the intake panel (see Figure 5-130). c. Tighten two fastening screws. Note Cisco Systems recommends that air filters be changed every three months. Cleaning or Replacing the Chassis Air Filter and Intake Panel The Cisco 7609 Router and the Cisco 7609-S Router are equipped a user-serviceable air filter that removes dust drawn into the router and intake panel. One time per month (or more often in environments where routers are prone to dust particles), examine the air filter and intake panel for damage and cleanliness

10 Chapter 5 Removal and Replacement Procedures Air Filters in C7603-S Chassis Caution Damage to the air filter and intake panel can restrict the airflow, cause overheating in the router, and degrade EMI performance. Be careful when cleaning and replacing the air filter. Air Filter Maintenance Follow the procedure described in Replacing the Air Filter on a Cisco 7609 Router and the Cisco 7609-S Router (Optional) section on page to remove and reinstall the air filter on the air filter assembly. After taking out the air filter, visually check the condition of the air filter to determine whether to clean or install a new replacement. If the air filter is dirty, clean the filter. Change the air filter if it is torn or worn out. Caution Do not vacuum the air filter while it is installed in the chassis. You must remove the air filter completely before you clean it to prevent contaminants from being drawn into the bays or cage. The cleaning process should be performed outside the router installation area. You can use the pressurized air to clean the air filter. If the filter appears worn or torn, dispose of it in a responsible manner and install a replacement air filter. Intake Panel Maintenance Visually check the condition of the intake panel (If the air filter assembly is fitted on the intake panel, remove it). If the intake panel is dirty, you need to clean the panel. Remove the intake panel from the router and take is outside the router installation area. Clean the intake panel using high presurrised air and replace it in the router. Caution Do not vacuum the air filter while it is installed in the chassis. You must remove the air filter completely before you clean it to prevent contaminants from being drawn into the bays or cage. The cleaning process should be performed outside the router installation area. Air Filters in C7603-S Chassis Do note that there are no air filters in a c7603-s chassis. Installing the Thermistor Module on a Cisco 7606-S Router This section describes how to install the thermistor module for the Cisco 7606-S router. The necessary parts can be ordered at listed in Table 5-2. Table 5-2 Thermistor Module Part Numbers Part Number THERM-7606S= Description Replacement thermistor module 5-133

11 7600-ES20-10G3CXL ETHERNET SERVICES MODULE 7600-ES20-10G3CXL ETHERNET SERVICES MODULE 7600-ES20-10G3CXL ETHERNET SERVICES MODULE 7600-ES20-10G3CXL ETHERNET SERVICES MODULE CLASS 1 LASER CLASS 1 LASER CLASS 1 LASER CLASS 1 LASER 0 Installing the Thermistor Module on a Cisco 7609-S Router Chapter 5 Removal and Replacement Procedures Perform these steps to replace a thermistor module. Step 1 Step 2 Remove the thermistor module by unscrewing two captive thumbscrews (see Figure 5-132) and sliding the termistor module out. Slide the replacement thermistor module into the chassis and tighten the two captive screws. the single captive screw that retains the thermistor module in the chassis. See Figure Figure Thermistor Module Replacement. FAN STATUS 1 A/L STATUS 1 Cisco A/L THERM-T606S A/L STATUS A/L A/L STATUS A/L A/L STATUS A/L 6 STATUS Installing the Thermistor Module on a Cisco 7609-S Router This section describes how to install the thermistor module for the Cisco 7609-S router. The necessary parts can be ordered at listed in Table 5-3. Table 5-3 Thermistor Module Part Numbers Part Number THERM-7609S= Description Replacement thermistor module Perform these steps to replace a thermistor module. Step 1 Remove the intake panel by unscrewing four captive thumbscrews (see Figure 5-133)

12 PORT 2 PORT 2 LINK ACTIVE ACTIVE Chapter 5 Removal and Replacement Procedures Installing the Thermistor Module on a Cisco 7609-S Router Figure Removing the Intake Panel Step 2 Unscrew the single captive screw that retains the thermistor module in the chassis. See Figure Figure Thermistor Module Thermistor slots 2 Captive screw 3 Flange Step 3 Grasp the flange on the thermistor module (see Figure 5-134) and pull to remove the thermistor module. See Figure

13 PORT 2 PORT 2 LINK ACTIVE ACTIVE Upgrading the Cisco 7600 Series Routers to a WS-SUP720-3BXL Chapter 5 Removal and Replacement Procedures Figure Thermistor Module Replacement Step 4 Step 5 Step 6 Insert the thermistor module until the faceplate of the module bottoms out to the ramp in the chassis. Tighten the captive screw on the module into the chassis. Reinstall the intake panel by tightening four captive thumbscrews. Upgrading the Cisco 7600 Series Routers to a WS-SUP720-3BXL To perform the upgrade, you must shut down the system. Before you shut down the system, you should first upload the current configuration to a server. This saves time when bringing the module back online. You can recover the configuration by downloading it from the server to the nonvolatile memory of the supervisor engine. For information on installing the WS-SUP720-3BXL, see Installing a Supervisor Engine or a Module in the Cisco 7600 Series Router Module Installation Guide. The SUP720-3BXL is supported with the following chassis. High-speed fans and larger power supplies are required for the WS-SUP720-3BXL. If your chassis has the low speed fan, you will need to upgrade them. For information on replacing the fans, see the Removing and Replacing the Fan Assembly procedure on page For information on replacing the power supplies, see Removing and Replacing the Power Supply procedure on page 5-2. Table 5-4 Required Fan Upgrades for the WS-SUP720-3BXL Supported Chassis Low Speed Fan (Original Fan) High Speed Fan (Required for the SUP720-3BXL) Cisco 7603 FAN-MOD-3 FAN-MOD-3HS Cisco 7604 N/A FAN-MOD-4HS Cisco 7606 FAN-MOD-6 FAN-MOD-6HS Cisco N/A FAN-MOD-09 Cisco 7613 WS-C6K-13SLOT-FAN WS-C6K-13SLOT-FAN

14 Chapter 5 Removal and Replacement Procedures Upgrading the Cisco 7600 Series Routers to a WS-SUP720-3BXL 1. Model CISCO7609 is equipped with two tiered-speed fan trays. There is no replacement or adjustment required. For model OSR-7609, refer to Table 5-5 Required Power Supply Upgrades for the WS-SUP720-3BXL Supervisor 720 and Supervisor 3BXL Supported Chassis AC DC Cisco 7603 WS-CAC-950W WS-CDC-950W Cisco 7604 N/A N/A Cisco 7606 WS-CAC-1900W WS-CDC-1900W Cisco 7609 WS-CAC-3000W WS-CAC-4000W WS-CDC-2500W PWR-4000-DC Cisco 7613 WS-CAC-3000W WS-CAC-4000W WS-CDC-2500W PWR-4000-DC 5-137

15 Upgrading the Cisco 7600 Series Routers to a WS-SUP720-3BXL Chapter 5 Removal and Replacement Procedures 5-138

16 APPENDIXA Technical Specifications Note This publication describes the following Cisco 7600 series routers: Cisco 7603 Router CISCO7603 Cisco 7603-S Router CISCO7603-S Cisco 7604 Router CISCO7604 Cisco 7606 Router CISCO7606 Cisco 7606-S Router CISCO7606-S Cisco 7609 Router CISCO7609 Cisco 7609-S Router CISCO7609-S Cisco 7613 Router CISCO7613 Information on the Cisco 7609 Router (product number OSR-7609) is in the Cisco 7609 Router Installation Guide, located at this URL: osrouter/index.htm This appendix provides the technical specifications for the Cisco 7600 series routers: Cisco 7603 Router, page A-2 Cisco 7603-S Router, page A-2 Cisco 7604 Router, page A-3 Cisco 7606 Router, page A-4 Cisco 7606-S Router, page A-5 Cisco 7609 Router, page A-6 Cisco 7609-S Router, page A-7 Cisco 7600 Series Router Power Supplies, page A-9 Regulatory Standards Compliance, page A-15 Refer to the Cisco 7600 Series Internet Router Module Installation Guide for module and interface port specifications. A-1

17 Cisco 7603 Router Appendix A Technical Specifications Cisco 7603 Router The Cisco 7603 Router specifications are provided in Table A-1. Table A-1 Cisco 7603 Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Humidity (RH), ambient (noncondensing) nonoperating and storage Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% 5% to 95% Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) Weight Power Supply 7 x x inches (17.78 x x cm). Chassis requires 4 RU 2 Chassis only: 28.5 lb (12.93 kg) Chassis fully configured with 1 supervisor engine, 2 modules, 2 AC-input PEMs, and 2 AC-input power supplies: 83 lb (37.65 kg) 950 W AC- or DC-input power supply optional second power supply can be installed in the chassis 1400 W AC-input power supply optional second power supply can be installed in the chassis Airflow FAN-MOD-3 (Standard fan tray) 170 CFM Acoustical Noise FAN-MOD-3HS (Optional high-speed fan tray) 270 CFM 64 to 76 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7603-S Router The Cisco 7603 Router specifications are provided in Table A-1. A-2

18 Appendix A Technical Specifications Cisco 7604 Router Table A-2 Cisco 7603 Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Humidity (RH), ambient (noncondensing) nonoperating and storage Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% 5% to 95% Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) Weight 7 x x 20.3 inches (17.78 x x cm). Chassis requires 4 RU 2 Chassis only: 28.8 lb (13.07 kg) Chassis fully configured with 1 supervisor engine, 2 modules, 2 DC-input PEMs, and 2 DC-input power supplies: 83 lb (37.65 kg) Power Supply 1500 W DC-input power supply optional second power supply can be installed in the chassis Airflow FAN-MOD-3SHS (Optional high-speed fan tray) 270 CFM Acoustical Noise 64 to 76 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7604 Router The Cisco 7604 Router specifications are provided in Table A-3. Table A-3 Cisco 7604 Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% A-3

19 Cisco 7606 Router Appendix A Technical Specifications Table A-3 Cisco 7604 Router Specifications (continued) Item Humidity (RH), ambient 5% to 95% (noncondensing) nonoperating and storage Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) Weight Power Supply Airflow Acoustical Noise Specification 8.7 x 17.5 x 21.6 inches (22.09 x x cm). Chassis requires 5 RU 2 Chassis only: 29.7 lb (13.5 kg) Chassis fully configured with 2 supervisor engines, 2 modules, 2 AC-input PEMs, and 2 AC-input power supplies: 97 lb ( kg); FAN-MOD-4HS, 6.1 lb (2.78 kg) 2700 W AC- or DC-input power supply optional second power supply can be installed in the chassis FAN-MOD-4HS 300 CFM 63.2 to 72.5 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7606 Router The Cisco 7606 Router specifications are provided in Table A-4. Table A-4 Cisco 7606 Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Humidity (RH), ambient (noncondensing) nonoperating and storage Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% 5% to 95% Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) x x inches (30.98 x x cm). Chassis requires 7 RU 2 A-4

20 Appendix A Technical Specifications Cisco 7606-S Router Table A-4 Cisco 7606 Router Specifications (continued) Item Weight Power Supply Airflow Acoustical Noise Specification Chassis only: 37.2 lb (16.5 kg) Chassis fully configured with 1 supervisor engine, 5 modules, 2 AC-input PEMs, and 2 AC-input power supplies: lb (60.42 kg); FAN-MOD-6HS, 7.7 lb (3.5 kg) 1900 W AC- or DC-input power supply optional second power supply can be installed in the chassis 2700 W AC-input power supply optional second power supply can be installed in the chassis. 540 CFM through system fan assembly 65.3 to 73.6 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7606-S Router The Cisco 7606 Router specifications are provided in Table A-5. Table A-5 Cisco 7606-S Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Humidity (RH), ambient (noncondensing) nonoperating and storage Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% 5% to 95% Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) x x inches (30.98 x x cm). Chassis requires 7 RU 2 A-5

21 Cisco 7609 Router Appendix A Technical Specifications Table A-5 Item Weight Power Supply Airflow Acoustical Noise Cisco 7606-S Router Specifications (continued) Specification Chassis only: 40.8 lb (17.2 kg) Chassis fully configured with 1 supervisor engine, 5 modules, and 2 AC-input power supplies: lb (60.42 kg); FAN-MOD-6SHS, 7.7 lb (3.5 kg), includes one fan tray W AC- or DC-input power supply optional second power supply can be installed in the chassis 540 CFM through system fan assembly 65.3 to 73.6 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7609 Router The Cisco 7609 Router specifications are provided in Table A-6. Table A-6 Cisco 7609 Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Humidity (RH), ambient (noncondensing) nonoperating and storage Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% 5% to 95% Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) Weight x x inches (93.34 x x cm). Chassis requires 21 RU 2 Chassis only: lb (56.35 kg) Chassis fully configured with 1 supervisor engine, 8 modules, 2 AC-input power supplies: 270 lb ( kg); FAN-MOD-09, 12.7 lb (5.8 Kg), includes two fan trays. A-6

22 Appendix A Technical Specifications Cisco 7609-S Router Table A-6 Cisco 7609 Router Specifications (continued) Item Specification Power Supply 2500 W DC-input power supply, 3000 W AC-input power supply, 4000 W DC-input power supply, 4000 W AC- input power supply, 6000 W AC- input power supply, 6000 W DC-input power supply optional second power supply can be installed in the chassis Airflow FAN-MOD-09 (High-speed fan tray) 760 CFM, 12.7 lb (5.8 Kg) Acoustical Noise 67 to 77 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7609-S Router The Cisco 7609-S router specifications are provided in Table A-6. Table A-7 Cisco 7609-S Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Humidity (RH), ambient (noncondensing) nonoperating and storage Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% 5% to 95% Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) Weight x x inches (93.34 x x cm).. Chassis requires 21 RU 2 Chassis only: lb (67.46 kg) Chassis fully configured with 1 supervisor engine, 8 modules, 2 AC-input power supplies: 270 lb ( kg); FAN-MOD-9SHS, 13.4 lb (6.1 kg), includes two fan trays. A-7

23 Cisco 7613 Router Appendix A Technical Specifications Table A-7 Cisco 7609-S Router Specifications (continued) Item Specification Power Supply 4000 W DC-input power supply, 4000 W AC- input power supply, 6000 W AC- input power supply, 6000 W DC-input power supply optional second power supply can be installed in the chassis Airflow 760 CFM through system fan assembly Acoustical Noise 67 to 77 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7613 Router The Cisco 7613 Router specifications are provided in Table A-8. Table A-8 Cisco 7613 Router Specifications Item Environmental Temperature, ambient operating Temperature, ambient nonoperating and storage Humidity (RH), ambient (noncondensing) operating Humidity (RH), ambient (noncondensing) nonoperating and storage Specification 32 F (0 C) to 104 F (40 C) 40 F ( 40 C) to 158 F (70 C) 10% to 90% 5% to 95% Altitude, operating Sea level to 10,000 feet (3048m) 1 Physical Characteristics Dimensions (H x W x D) Weight Power Supply x 17.3 x 18.1 inches (84.2 x 43.9 x 46 cm). Chassis requires 19 RU 2 Chassis only: 90 lb (40.82 kg) Chassis fully configured with 2 supervisor engines, 11 modules, and two power supplies: 240 lb (108.9 kg) 2500 W DC-input power supply, 3000 W AC-input power supply, 4000 W DC-input power supply, 4000 W AC- input power supply, 6000 W AC- input power supply, 6000 W DC-input power supply optional second power supply can be installed in the chassis A-8

24 Appendix A Technical Specifications Cisco 7600 Series Router Power Supplies Table A-8 Cisco 7613 Router Specifications (continued) Item Specification Airflow WS-C6K-13SLT-FAN2 (Optional high-speed fan tray) 1090 CFM Acoustical Noise 61.4 to 77 db. International Organization for Standardization (ISO) 7779: Bystander position operating to an ambient temperature of 86 F (30 C). 1. Designed and tested for normal operation for altitudes up to ft (3048m); safety approvals apply only to an operating altitude of 6500 feet (2000 m). 2. RU = rack units Cisco 7600 Series Router Power Supplies Table A-9 lists the specifications for the Cisco 7600 series router power supplies. Table A-9 Power Supply Specifications Item Specification 950 W AC- and DC-input Power Supplies AC-input type Autoranging input with power factor corrector AC-input voltage rating 100 to 240 VAC (±10% for full range) AC-input current rating 12-5 A AC-input frequency 50/60 Hz (nominal) Power supply output capacity 950 W maximum ( VAC) DC-input voltage rating -48 VDC to -60 VDC continuous DC-input current rating 25 A Power supply output (AC supply) 15A, 2.5A, 19.15A Power supply output (DC supply) 15A, 2.5A, 19.15A Output holdup time 20 ms minimum (AC-input power supply) 4 ms (DC-input power supply) 1400 W AC-input Power Supplies Specification AC-input type Autoranging input with power factor corrector AC-input voltage rating 100 to 240 VAC (±10% for full range) AC-input current rating VAC VAC AC-input frequency 50/60 Hz (nominal) (±3 Hz for full range) Power supply output capacity 1400 W Power supply output V 3.3V V A-9

25 Cisco 7600 Series Router Power Supplies Appendix A Technical Specifications Table A-9 Power Supply Specifications (continued) Item 1500 W DC-input Power Supply Power supply output capacity 1500 W maximum. System power dissipation 1770 W (total input power). DC-input voltage rating -48VDC 37A in North America (operating range: -40.5VDC to -56VDC) DC-input current 60VDC 29A for International (operating range: -55VDC to -72VDC). -48VDC input voltage Power supply output rating 15A, 2.5A, 29.4A DC-input voltage rating Specification A-10

26 Appendix A Technical Specifications Cisco 7600 Series Router Power Supplies Table A-9 Power Supply Specifications (continued) Item 1900 W AC- and DC-input Power Supply AC-input type AC-input voltage rating AC-input current rating AC-input frequency Power supply output capacity DC-input voltage rating DC-input current rating Power supply output (AC supply) Autoranging input with power factor corrector 100 to 240 VAC (±10% for full range) 12A 50/60 Hz (nominal) 1050 W maximum ( VAC) 1900 W maximum ( VAC) -48 VDC to -60 VDC continuous 50A 15A, 2.5A, 20.38A (110 VAC) 15A, 2.5A, 37.38A (220 VAC) Power supply output (DC supply) 15A, 2.5A, 37.38A Output holdup time 2500 W DC-input Power Supply Specification Power supply output capacity System power dissipation DC-input voltage rating DC-input current Power supply output rating DC input terminal block Output holdup time 20 ms minimum (AC-input power supply) 8 ms (DC-input power supply) 2500 W maximum W (total input power). -48 VDC to -60 VDC continuous. 80A +3.3V, +5V, +12V, +42V. Accepts 2-14 AWG copper conductors. Actual size of the wire needed is determined by the installer or local electrician. Terminal block material rated at 150 C. 4 ms 2700 W AC-input Power Supply Specification AC-input type Autoranging input with power factor corrector AC-input voltage rating 100 to 120 VAC, 200 to 240 VAC (±10% for full range) AC-input current rating VAC (2700 W output) VAC (1350 W output) Power supply output capacity 1350 W maximum ( VAC) 2700 W maximum ( VAC) AC-input frequency 50/60 Hz (nominal) (±3% for full range) Power supply output 15A, 2.5A, 27.49A (110 VAC) KVA rating Specification 15A, 2.5A, 55.61A (220 VAC) 3.4 KVA (high-line operation) A-11

27 Cisco 7600 Series Router Power Supplies Appendix A Technical Specifications Table A-9 Power Supply Specifications (continued) Item Specification Output holdup time 20 ms minimum 2700 W DC-input Power Supply Specification Power supply output capacity 2700W with two inputs active; 1350 W with one input active. System power dissipation 3500W (total input power). DC-input voltage -48VDC 37A in North America (operating range: -40.5VDC to -56VDC) -60VDC 29A for International (operating range: -55VDC to -72VDC). DC-input current 40A per each DC -48VDC input voltage (total two inputs) Power supply output 15A, 5.0A, 27.49A (one DC input) 15A, 5.0A, 55.61A (Two DC input) DC input terminal block Accepts 4 AWG copper conductors. Actual size of the wire needed is determined by the installer or local electrician. Output holdup time 8 ms Ground Nut 1/4 inch x 20 Washer 1/4 inch split type Lugs required Industry Standard 2-hole compression lug with holes on5/8- inch centers. Maximum torque 36 inch-lb 3000 W AC-input Power Supply Specification AC-input type Autoranging input with power factor correction 1 (PFC) AC-input voltage rating 100 to 120 VAC, 200 to 240 VAC (±10% for full range) AC-input current rating VAC (3000 W output) VAC (1400 W output) Power supply output capacity 1400 W maximum ( VAC) 3000 W maximum ( VAC) AC-input frequency 50/60 Hz (nominal) (±3% for full range) Power supply output 1400 W maximum ( VAC) 3000 W maximum ( VAC) KVA rating 3.6 KVA (high-line operation) Output holdup time 20 ms minimum 4000 W AC-input Power Supply Specification AC-input type High-line input with power factor corrector, 30A single-phase circuit A-12

28 Appendix A Technical Specifications Cisco 7600 Series Router Power Supplies Table A-9 Power Supply Specifications (continued) Item AC-input voltage rating AC-input current rating Power supply output capacity AC-input frequency 200 to 240 VAC (±10% for full range) 23A 4000W maximum 50/60 Hz (nominal) (±3% for full range) Power supply output +3.3V, +5V, +12V, +42V KVA rating Output holdup time 5.4 KVA maximum 20 ms minimum 4000 W DC-input Power Supply Specification Power supply output capacity System power dissipation DC-input voltage DC-input current Power supply output 4000W with three inputs active; 2700 W with two inputs active. 5200W (total input power) -48VDC 37A in North America (operating range: -40.5VDC to -56VDC), -60VDC 29A for International (operating range: -55VDC to -72VDC) 40A per each DC -48VDC input voltage (total three inputs) A, A, A (three inputs)/59.68a (two inputs) DC input terminal block Accepts 4 AWG copper conductors. Actual size of the wire needed is determined by the installer or local electrician. Output holdup time 8 ms Terminal and Ground Studs 1/4 inch x 20 Washer 1/4 inch split type Hex Nut 1/4 inch-20 x.226 inch T, SS Maximum Torque 36 inch-lb. Lugs Required Industry Standard 2-hole compression lug with holes on 5/8- inch centers Recommended Ground Terminal Power Supply Bay #1: left ground termination Power Supply Bay #2: Right ground termination 4500 W DC-input Power Supply Specification Power supply output capacity 4500W with three inputs active; 3000 W with two inputs active, 1500 w with one input active. System power dissipation 5300W (total input power) DC-input voltage -48VDC 37A in North America (operating range: -40.5VDC to -56VDC), -60VDC 29A for International (operating range: -55VDC to -72VDC) DC-input current Specification 40A per each DC -48VDC input voltage (total three inputs) A-13

29 Cisco 7600 Series Router Power Supplies Appendix A Technical Specifications Table A-9 Power Supply Specifications (continued) Item Power supply output DC input terminal block Output holdup time Terminal and Ground Studs Hex Nut with integrated washer: Maximum Torque Lugs Required Specification A, A, A (three inputs)/ 60A (two inputs)/ 30A (one input) Accepts up to 2AWG copper conductors. Actual size of the wire needed is determined by the installer or local electrician. 8 ms 1/4 inch-20 1/4 inch-20, SS 36 inch-lb. Industry Standard 2-hole compression lug with holes on 5/8- inch centers 6000 W DC-input Power Supply Specification Power supply output capacity 6000 W with four inputs active; 4506 W with three inputs active; 2800 W with two inputs active System power dissipation DC-input voltage 7060 W -48VDC 37A in North America (operating range: -40.5VDC to -56VDC), -60VDC 29A for International (operating range: -55VDC to -72VDC) DC-input current 40A per each DC -48VDC input voltage (total four inputs) Power supply output 2800W operation (two DC inputs) VDC VDC 42 VDC 4500W operation (three DC inputs) VDC VDC VDC 6000W operation (four DC inputs) VDC VDC VDC DC input terminal block Accepts up to 2 AWG copper conductors. Actual size of the wire needed is determined by the installer or local electrician. Output holdup time 8 ms Terminal and Ground Studs 1/4 inch x 20 Hex Nut with Integrated Washer 1/4 inch-20 A-14

30 Appendix A Technical Specifications Regulatory Standards Compliance Table A-9 Power Supply Specifications (continued) Item Maximum Torque Specification 36 inch-lb. Lugs Required Industry Standard 2-hole compression lug with holes on 5/8- inch centers 6000 W AC-input Power Supply Specification AC-input type High-line input with power factor correction (PFC) included AC-input voltage rating Single-phase, 100 to 120 VAC, 200 to 240 VAC (±10% for full range) AC-input current rating 16 A each input Power supply output capacity 2900 W maximum (one input active at 220 VAC, or both inputs active and one input is 110 VAC and the other is 220 VAC) 6000 W maximum (both inputs active at 220 VAC) AC-input frequency 50/60 Hz (nominal) (±3% for full range) Power supply output 2900 W operation (one 220 VAC source or two 110 VAC sources) V V V 6000 W operation (two 220 VAC sources) V V V KVA rating 7.2 KVA (high-line operation) Output holdup time 20 ms minimum 1. Power factor correction is a standard feature on all Cisco 7600 series AC-input power supplies. PFC reduces the reactive component in the source AC current allowing higher power factors (typically 99 percent or better) and lower harmonic current components. Regulatory Standards Compliance The Cisco 7600 series routers comply with the regulatory standards listed in the Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers document. A-15

31 Regulatory Standards Compliance Appendix A Technical Specifications A-16

32 APPENDIXB Connector and Cable Specifications This chapter describes the cables and connectors used with the Cisco 7600 series routers. The chapter is divided into the following sections: Connector Specifications, page B-1 Cable Specifications, page B-7 Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023 Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021 Connector Specifications This section covers the types of connectors used with the Cisco 7600 series routers: RJ-45, page B-1 Mini-SMB, page B-2 MT-RJ, page B-2 LC, page B-3 SC-Type, page B-3 Gigabit Interface Converters, page B-4 Note For information on cleaning optical interfaces, see RJ-45 The RJ-45 connector (shown in Figure B-1) is used to connect a Category 3 or Category 5 shielded or unshielded twisted-pair cable from the external network to the module interface connector. B-1

33 Connector Specifications Appendix B Connector and Cable Specifications Figure B-1 RJ-45 Interface Cable Connector RJ-45 (both ends) Pin 1 Pin 8 Mini-SMB The mini-smb connector (shown in Figure B-2) is used to connect the channelized DS3 OSMs to optical networks using RG Ohm copper coax cable. Figure B-2 Mini-SMB Cable Connector The following cable options are available: 2-MINISMB/BNC-M Two 10-foot (3-meter) cables with mini-smb to male BNC connectors 2-MINISMB/BNC-F Two 10-foot (3-meter) cables with mini-smb to female BNC connectors 2-MINISMB-OPEN Two 82-foot (25-meter) cables with mini-smb, open-ended MT-RJ Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures. The MT-RJ style connector, shown in Figure B-3, is used on fiber-optic modules to increase port density. Figure B-3 MT-RJ Connector When you are connecting MT-RJ cables to a module, make sure that you firmly press the connector plug into the socket. The upper edge of the plug must snap into the upper front edge of the socket. You may or may not hear an audible click. Gently pull on the plug to confirm whether or not the plug is locked B-2

34 Appendix B Connector and Cable Specifications Connector Specifications into the socket. To disconnect the plug from the socket, press down on the raised portion on top of the plug (releasing the latch). You should hear an audible click indicating that the latch has released. Carefully pull the plug out of the socket. When you disconnect the fiber-optic cable from the module, grip the body of the connector. Do not grip the connector jacket-sleeve. Gripping the sleeve can, over time, compromise the integrity of the fiber-optic cable termination in the MT-RJ connector. Always make sure that you insert the connector completely into the socket. This action is especially important when you are making a connection between a module and a long distance (1.24 miles) (2 km) or a suspected highly attenuated network. If the link LED does not light, try removing the network cable plug and reinserting it firmly into the module socket. It is possible that enough dirt or skin oils have accumulated on the plug faceplate (around the optical-fiber openings) to generate significant attenuation, reducing the optical power levels below threshold levels so that a link cannot be made. To clean the MT-RJ plug faceplate, perform these steps: Step 1 Step 2 Step 3 Use a lint-free tissue soaked in 99 percent pure isopropyl alcohol to gently wipe the faceplate. Carefully wipe the faceplate with a dry lint-free tissue. Remove any residual dust from the faceplate with compressed air before installing the cable. Note Make sure that dust caps are installed on all unused module connectors and unused network fiber-optic cable connectors. LC Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures. The LC fiber-optic connector, shown in Figure B-4, is used to connect the channelized OC-12 and OC-48 OSMs to optical networks using SMF. Figure B-4 LC Fiber-Optic Connector SC-Type Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 70 B-3

35 Connector Specifications Appendix B Connector and Cable Specifications The SC-type fiber connector, shown in Figure B-5, is used to connect fiber-optic module ports with the external network. Figure B-5 SC-Type Fiber-Optic Connector Gigabit Interface Converters Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 70 A GBIC is a hot-swappable input/output device that plugs into a Gigabit Ethernet module, linking the module with the fiber-optic network. GBICs are available in two physical models. There are three optical models and 32 dense wavelength division multiplexing (DWDM) models. The two physical models are shown in Figure B-6. The three optical models are listed in Table B-1. The DWDM models are listed in Table B-2. Figure B-6 GBIC Physical Styles Receiver Transmitter Clip Receiver Transmitter Handle Table B-1 GBIC Optical Model List GBIC Short wavelength (1000BASE-SX) Long wavelength/long haul (1000BASE-LX/LH) Extended distance (1000BASE-ZX) Product Number WS-G5484 WS-G5486 WS-G5487 B-4

36 Appendix B Connector and Cable Specifications Connector Specifications WS-G5484 The WS-G5484 GBIC (1000BASE-SX) operates on ordinary multimode fiber-optic link spans of up to 550 meters in length. WS-G5486 The WS-G5486 GBIC (1000BASE-LX/LH) interfaces fully comply with the IEEE 802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach 10 km over single-mode fiber (SMF), versus the 5 km specified in the standard. WS-G5487 The WS-G5487 GBIC (1000BASE-ZX) operates on ordinary single-mode fiber-optic link spans of up to 70 km in length. Link spans of up to 100 km are possible using premium single-mode fiber or dispersion-shifted single-mode fiber. (Premium single-mode fiber has a lower attenuation per unit length than ordinary single-mode fiber; dispersion-shifted single-mode fiber has both lower attenuation per unit length and less dispersion.) The WS-G5487 GBIC must be coupled to single-mode fiber-optic cable, which is the type of cable typically used in long-haul telecommunications applications. The WS-G5487 GBIC will not operate correctly when coupled to multimode fiber, and it is not intended to be used in application environments (e.g., building backbones or horizontal cabling) where multimode fiber is frequently used. The WS-G5487 GBIC is intended to be used as a physical medium dependent (PMD) component for Gigabit Ethernet interfaces, as found on various switch and router products. It will operate at a signaling rate of 1250 MBaud, transmitting and receiving 8B/10B encoded data. When shorter distances of single-mode fiber are used, you might need to insert an in-line optical attenuator in the link to avoid overloading the receiver: Insert a 10-dB in-line optical attenuator between the fiber-optic cable plant and the receiving port on the WS-G5487 GBIC at each end of the link whenever the fiber-optic cable span is less than 25 km. Insert a 5-dB in-line optical attenuator between the fiber-optic cable plant and the receiving port on the WS-G5487 GBIC at each end of the link whenever the fiber-optic cable span is equal to or greater than 25 km and less than 50 km. GBICs use an SC-type connector to link the module to the fiber-optic cable. Dense Wavelength Division Multiplexing (DWDM) GBIC Transceivers DWDM GBIC transceivers are used as part of a DWDM optical network to provide high-capacity bandwidth across an optical fiber network. There are 32 fixed-wavelength GBICs that support the International Telecommunications Union (ITU) 100 GHz wavelength grid. Refer to your release notes for a list of compatible modules and the software release level necessary to support these DWDM GBICs. Figure B-7 shows the physical form of the DWDM GBIC. B-5

37 Connector Specifications Appendix B Connector and Cable Specifications Figure B-7 DWDM GBIC Transceiver Receiver Transmitter Table B-2 lists the DWDM GBIC product numbers, a brief description of the GBIC, and the ITU channel number. Table B-2 DWDM GBIC Product Numbers and ITU Channel Numbers DWDM GBIC Product Number Description ITU Channel DWDM-GBIC BASE-DWDM nm GBIC 21 DWDM-GBIC BASE-DWDM nm GBIC 22 DWDM-GBIC BASE-DWDM nm GBIC 23 DWDM-GBIC BASE-DWDM nm GBIC 24 DWDM-GBIC BASE-DWDM nm GBIC 26 DWDM-GBIC BASE-DWDM nm GBIC 27 DWDM-GBIC BASE-DWDM nm GBIC 28 DWDM-GBIC BASE-DWDM nm GBIC 29 DWDM-GBIC BASE-DWDM nm GBIC 31 DWDM-GBIC BASE-DWDM nm GBIC 32 DWDM-GBIC BASE-DWDM nm GBIC 33 DWDM-GBIC BASE-DWDM nm GBIC 34 DWDM-GBIC BASE-DWDM nm GBIC 36 DWDM-GBIC BASE-DWDM nm GBIC 37 DWDM-GBIC BASE-DWDM nm GBIC 38 DWDM-GBIC BASE-DWDM nm GBIC 39 DWDM-GBIC BASE-DWDM nm GBIC 41 DWDM-GBIC BASE-DWDM nm GBIC 42 DWDM-GBIC BASE-DWDM nm GBIC 43 DWDM-GBIC BASE-DWDM nm GBIC 44 DWDM-GBIC BASE-DWDM nm GBIC 46 DWDM-GBIC BASE-DWDM nm GBIC 47 DWDM-GBIC BASE-DWDM nm GBIC 48 DWDM-GBIC BASE-DWDM nm GBIC 49 DWDM-GBIC BASE-DWDM nm GBIC 51 DWDM-GBIC BASE-DWDM nm GBIC 52 B-6

38 Appendix B Connector and Cable Specifications Cable Specifications Table B-2 DWDM GBIC Product Numbers and ITU Channel Numbers (continued) DWDM GBIC Product Number Description ITU Channel DWDM-GBIC BASE-DWDM nm GBIC 53 DWDM-GBIC BASE-DWDM nm GBIC 54 DWDM-GBIC BASE-DWDM nm GBIC 56 DWDM-GBIC BASE-DWDM nm GBIC 57 DWDM-GBIC BASE-DWDM nm GBIC 58 DWDM-GBIC BASE-DWDM nm GBIC 59 Cable Specifications The Cisco 7600 series router comes with an accessory kit that contains the cable and adapters you need to connect a console (an ASCII terminal or PC running terminal emulation software) or modem to the console port. The accessory kit includes these items: RJ-45-to-RJ-45 rollover cable RJ-45-to-DB-9 female DTE adapter (labeled Terminal ) RJ-45-to-DB-25 female DTE adapter (labeled Terminal ) RJ-45-to-DB-25 male DCE adapter (labeled Modem ) The cable and adapters are the same cable and adapters that ship with the Cisco 2500 series routers and other Cisco products. Console Port Mode Switch The supervisor engine front-panel console port mode switch allows you to connect a terminal or modem to the console port as follows: Note Use a ballpoint pen tip or other small, pointed object to access the console port mode switch. The switch is shipped in the in position. Mode 1 Switch in the in position. Use this mode to connect a terminal to the console port using the RJ-45-to-RJ-45 rollover cable and DTE adapter (labeled Terminal ). You can also use this mode to connect a modem to the console port using the RJ-45-to-RJ-45 rollover cable and DCE adapter (labeled Modem ). See the Console Port Mode 1 Signaling and Pinouts section on page B-8. Mode 2 Switch in the out position. Use this mode to connect a terminal to the console port using the Catalyst 5000 family Supervisor Engine III console cable and appropriate adapter for the terminal connection (cable and adapter are not provided). See the Console Port Mode 2 Signaling and Pinouts section on page B-10. B-7

39 Cable Specifications Appendix B Connector and Cable Specifications Identifying a Rollover Cable You can identify a rollover cable by comparing the two ends of the cable. Holding the cables side by side, with the tab at the back, the wire connected to the pin on the outside of the left plug should be the same color as the wire connected to the pin on the outside of the right plug. (See Figure B-8.) If your cable was purchased from Cisco Systems, pin 1 will be white on one connector, and pin 8 will be white on the other. (A rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5.) Figure B-8 Identifying a Rollover Cable Pin 1 and pin 8 should be the same color Pin 1 Pin 8 H3824 Console Port Mode 1 Signaling and Pinouts This section provides the signaling and pinouts for the console port in mode 1 (port mode switch in the in position). DB-9 Adapter (for Connecting to a PC) Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9 female DTE adapter (labeled Terminal ) to connect the console port to a PC running terminal emulation software. Table B-3 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-9 female DTE adapter. Table B-3 Port Mode 1 Signaling and Pinouts (DB-9 Adapter) Console Port RJ-45-to-RJ-45 Rollover Cable RJ-45-to-DB-9 Terminal Adapter Console Device Signal RJ-45 Pin RJ-45 Pin DB-9 Pin Signal RTS CTS DTR DSR TxD RxD B-8

40 Appendix B Connector and Cable Specifications Cable Specifications Table B-3 Port Mode 1 Signaling and Pinouts (DB-9 Adapter) Console Port RJ-45-to-RJ-45 Rollover Cable GND GND GND GND RxD TxD DSR DTR CTS RTS 1. Pin 1 is connected internally to Pin 8. DB-25 Adapter (for Connecting to a Terminal) RJ-45-to-DB-9 Terminal Adapter Console Device Signal RJ-45 Pin RJ-45 Pin DB-9 Pin Signal Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 female DTE adapter (labeled Terminal ) to connect the console port to a terminal. Table B-4 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 female DTE adapter. Table B-4 Port Mode 1 Signaling and Pinouts (DB-25 Adapter) Console Port RJ-45-to-RJ-45 Rollover Cable RJ-45-to-DB-25 Terminal Adapter Console Device Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal RTS CTS DTR DSR TxD RxD GND GND GND GND RxD TxD DSR DTR CTS RTS 1. Pin 1 is connected internally to Pin 8. Modem Adapter Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 male DCE adapter (labeled Modem ) to connect the console port to a modem. Table B-5 lists the pinouts for the asynchronous serial auxiliary port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 male DCE adapter. B-9

41 Cable Specifications Appendix B Connector and Cable Specifications Table B-5 Port Mode 1 Signaling and Pinouts (Modem Adapter) Console Port RJ-45-to-RJ-45 Rollover Cable RJ-45-to-DB-25 Modem Adapter Modem Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal RTS RTS DTR DTR TxD TxD GND GND GND GND RxD RxD DSR DCD CTS CTS 1. Pin 1 is connected internally to Pin 8. Console Port Mode 2 Signaling and Pinouts This section provides the signaling and pinouts for the console port in mode 2 (port mode switch in the out position). (See Table B-6 for the pinouts.) Table B-6 Port Mode 2 Signaling and Pinouts (Port Mode Switch Out) Console Port Console Device Pin (signal) Input/Output 1 (RTS) 1 Output 2 (DTR) Output 3 (RxD) Input 4 (GND) GND 5 (GND) GND 6 (TxD) Output 7 (DSR) Input 8 (CTS) 1 Input 1. Pin 1 is connected internally to Pin 8. Mode-Conditioning Patch Cord When using the long wavelength/long-haul (LX/LH) GBIC with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord (Cisco product number CAB-GELX-625 or equivalent) between the GBIC and the multimode fiber (MMF) cable on both the transmit and receive ends of the link. The patch cord is required for link distances greater than 984 feet (300 meters). B-10

42 Appendix B Connector and Cable Specifications Cable Specifications Note We do not recommend using the LX/LH GBIC and MMF without the patch cord for very short link distances of 33 to 328 feet (10 to 100 meters). The result could be an elevated bit error rate (BER). The patch cord is required to comply with IEEE standards. IEEE found that link distances could not be met with certain types of fiber-optic cable due to a problem in the center of some fiber-optic cable cores. The solution is to launch light from the laser at a precise offset from the center by using the patch cord. At the output of the patch cord, the LX/LH GBIC complies with the IEEE 802.3z standard for 1000BASE-LX. Patch Cord Configuration Example Figure B-9 shows a typical patch cord configuration. Figure B-9 Patch Cord Configuration Patch cord Building cable plant Patch cord 1000BASE-LX/LH port Rx Tx Patch panel Patch panel Tx Rx 1000BASE-LX/LH port Link span greater than 984 ft (300 m) Patch Cord Installation Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Plug the end of the patch cord labeled To Equipment into the GBIC. (See Figure B-10.) Plug the end labeled To Cable Plant into the patch panel. The patch cord is 9.84 feet (3 meters) long and has duplex SC-type male connectors at each end. Figure B-10 Patch Cord Installation To equipment To cable plant B-11

43 Cable Specifications Appendix B Connector and Cable Specifications Differential Mode Delay When an unconditioned laser source designed for operation on an SMF cable is directly coupled to an MMF cable, differential mode delay (DMD) might occur. DMD can degrade the modal bandwidth of the fiber-optic cable. This degradation causes a decrease in the link span (the distance between the transmitter and the receiver) that can be reliably supported. The Gigabit Ethernet specification (IEEE 802.3z) outlines parameters for Ethernet communications at a gigabit-per-second rate. The specification offers a higher-speed version of Ethernet for backbone and server connectivity using existing deployed MMF cable by defining the use of laser-based optical components to propagate data over MMF cable. Lasers function at the baud rates and longer distances required for Gigabit Ethernet. The 802.3z Gigabit Ethernet Task Force has identified the DMD condition that occurs with particular combinations of lasers and MMF cable. The results create an additional element of jitter that can limit the reach of Gigabit Ethernet over MMF cable. With DMD, a single laser light pulse excites a few modes equally within an MMF cable. These modes, or light pathways, then follow two or more different paths. These paths might have different lengths and transmission delays as the light travels through the cable. With DMD, a distinct pulse propagating down the cable no longer remains a distinct pulse or, in extreme cases, might become two independent pulses. Strings of pulses can interfere with each other making it difficult to recover data. DMD does not occur in all deployed fibers; it occurs with certain combinations of worst-case fibers and worst-case transceivers. Gigabit Ethernet experiences this problem because of its very high baud rate and its long MMF cable lengths. SMF cable and copper cable are not affected by DMD. MMF cable has been tested for use only with LED sources. LEDs can create an overfilled launch condition within the fiber-optic cable. The overfilled launch condition describes the way LED transmitters couple light into the fiber-optic cable in a broad spread of modes. Similar to a light bulb radiating light into a dark room, the generated light that shines in multiple directions can overfill the existing cable space and excite a large number of modes. (See Figure B-11.) Figure B-11 LED Transmission Compared to Laser Transmission LED transmission LED Laser transmission Laser Lasers launch light in a more concentrated fashion. A laser transmitter couples light into only a fraction of the existing modes or optical pathways present in the fiber-optic cable. (See Figure B-11.) The solution is to condition the laser light launched from the source (transmitter) so that it spreads the light evenly across the diameter of the fiber-optic cable, making the launch look more like an LED source to the cable. The objective is to scramble the modes of light to distribute the power more equally in all modes and prevent the light from being concentrated in just a few modes. B-12

44 Appendix B Connector and Cable Specifications Cable Specifications An unconditioned launch, in the worst case, might concentrate all of its light in the center of the fiber-optic cable, exciting only two or more modes equally. A significant variation in the amount of DMD is produced from one MMF cable to the next. No reasonable test can be performed to survey an installed cable plant to assess the effect of DMD. Therefore, you must use the mode-conditioning patch cords for all uplink modules using MMF when the link span exceeds 984 feet (300 meters). For link spans less than 300 meters, you can omit the patch cord (although there is no problem using it on short links). For link spans less than 984 feet (300 meters), you can omit the patch cord. Note We do not recommend using the LX/LH GBIC and MMF without a patch cord for very short link distances of 33 to 328 feet (10 to 100 meters). The result could be an elevated bit error rate (BER). B-13

45 Cable Specifications Appendix B Connector and Cable Specifications B-14

46 APPENDIXC Configuration Register Information The following information is found in this appendix: Configuration Bit Meanings, page C-1 Displaying the Configuration Register While Running Cisco IOS, page C-5 Displaying the Configuration Register While Running ROM Monitor, page C-5 Setting the Configuration Register While Running Cisco IOS, page C-6 Setting the Configuration Register While Running ROM Monitor, page C-6 Configuration Bit Meanings Use the processor configuration register information contained in this appendix to do the following: Set and display the configuration register value Force the system into the bootstrap program Select a boot source and default boot filename Enable or disable the Break function Control broadcast addresses Set the console terminal baud rate Load operating software from ROM Enable booting from a Trivial File Transfer Protocol (TFTP) server Table C-1 lists the meaning of each of the configuration memory bits. Following the table is a more in-depth description of each setting. Table C-1 Configuration Register Bit Settings Bit No. Hex Meaning x0000 0x000F Boot field 06 0x0040 Causes the system software to ignore nonvolatile random-access memory (NVRAM) contents 07 0x0080 OEM (original equipment manufacturer) bit enabled 08 0x0100 Break disabled 10 0x0400 IP broadcast with all zeros C-1

47 Configuration Bit Meanings Appendix C Configuration Register Information Table C-1 Configuration Register Bit Settings (continued) Bit No. Hex Meaning x800 0x1000 Console line speed 13 0x2000 Boots default ROM software if initial boot fails 14 0x4000 IP broadcasts do not have network numbers 15 0x8000 Enables diagnostic messages and ignores NVRAM contents Bits 0 3 The lowest four bits of the processor configuration register (bits 3, 2, 1, and 0) form the boot field. Table C-2 provides information about the bits settings. Table C-2 Bits 0 3 Settings Boot Field Meaning 0 Stays at the system bootstrap prompt (ROM monitor) on a reload or power cycle 1 Boots the boot helper image as a system image 2 Full boot process, which loads the Cisco IOS image into Flash memory 2-F Specifies a default filename for booting over the network from a TFTP server The boot field specifies a number in binary. If you set the boot field value to 0, you must have a console port access to boot the operating system manually. Boot the operating system by entering the b command at the bootstrap prompt as follows: > b [tftp] flash filename Definitions of the various command options follow: b Boots the default system software from ROM b flash Boots the first file in Flash memory b filename [host] Boots over the network using TFTP b flash filename Boots the file (filename) from Flash memory If you set the boot field value to a value of 2 through F, and there is a valid system boot command stored in the configuration file, the router boots the system software as directed by that value. (See Table C-3.) If you set the boot field to any other bit pattern, the router uses the resulting number to form a default boot filename for netbooting. If there are no boot commands in the configuration file, the router attempts to boot the first file in system Flash memory. If no file is found in system Flash memory, the router attempts to netboot a default file with a name derived from the value of the boot field (for example, cisco2-7301). If the netboot attempt fails, the boot helper image in boot flash memory will boot up. If boot commands are in the configuration file, the router software processes each boot command in sequence until the process is successful or the end of the list is reached. If the end of the list is reached without a file being successfully booted, the router will retry the netboot commands up to six times if bit 13 of the configuration register is set, otherwise it will load the operating system software available C-2

48 Appendix C Configuration Register Information Configuration Bit Meanings in ROMmon. If bit 13 is not set, the router will continue to netboot images indefinitely. The default setting for bit 13 is 0. If bit 13 is set, the system boots the boot helper image found in boot flash memory without any retries. The server creates a default filename as part of the automatic configuration processes. To form the boot filename, the server starts with Cisco and links the octal equivalent of the boot field number, a dash, and the image name. Table C-3 lists the default boot filenames or actions. Note A boot system configuration command in the router configuration in NVRAM overrides the default netboot filename. Table C-3 Default Boot Filenames Action/File Name Bit 3 Bit 2 Bit 1 Bit 0 Bootstrap mode ROM software Flash software cisco3-< image-name1> cisco4-<image-name2> cisco5-<image-name3> cisco6-<image-name4> cisco7-<image-name5> cisco10-<image-name6> cisco11-<image-name7> cisco12-<image-name8> cisco13-<image-name9> cisco14-<image-name10> cisco15-<image-name11> cisco16-<image-name12> cisco17-<image-name13> Bit 6 Bit 6 causes the system software to ignore nonvolatile random-access memory (NVRAM) contents. Bit 7 Bit 7 enables the OEM bit. It disables the bootstrap messages at startup. C-3

49 Configuration Bit Meanings Appendix C Configuration Register Information Bit 8 Bit 8 controls the console Break key. Setting bit 8 (the factory default) causes the processor to ignore the console Break key. Clearing bit 8 causes the processor to interpret Break as a command to force the system into the bootstrap monitor, halting normal operation. A Break can be sent in the first sixty seconds while the system reboots, regardless of the configuration settings. Bit 10 and Bit 14 Bit 10 controls the host portion of the Internet IP broadcast address. Setting bit 10 causes the processor to use all zeros; clearing bit 10 (the factory default) causes the processor to use all ones. B it 10 interacts with bit 14, which controls the network and subnet portions of the IP broadcast address. Table C-4 shows the combined effect of bit 10 and bit 14. Table C-4 Bit 10 and Bit 14 Settings Bit 14 Bit 10 IP Address (<net> <host>) Off Off <ones><ones> Off On <zeros><zeros> On On <net><zeros> On Off <net><ones> Bit 11 and Bit 12 Bit 11 and Bit 12 in the configuration register determine the baud rate of the console terminal. Table C-5 shows the bit settings for the four available baud rates. (The factory set default baud rate is 9600.) Table C-5 Bit 11 and Bit 12 Settings Baud Bit 12 Bit Bit 13 Bit 13 determines the server response to a bootload failure. If boot commands are in the configuration file, the router software processes each boot command in sequence until the process is successful or the end of the list is reached. If the end of the list is reached without a file being successfully booted, the router will retry the netboot commands up to six times if bit 13 of the configuration register is set, otherwise it will load the operating system software available in ROMmon. If bit 13 is not set, the router will continue to netboot images indefinitely. The default setting for bit 13 is 0. If bit 13 is set, the system boots the boot helper image found in boot flash memory without any retries. C-4

50 Appendix C Configuration Register Information Displaying the Configuration Register While Running Cisco IOS Bit 15 Bit 15 enables diagnostic messages and ignores NVRAM contents. Displaying the Configuration Register While Running Cisco IOS The configuration register can be viewed by using the show version or show hardware command. The following is sample output of the show version command from a Cisco 7301 router. Cisco Internetwork Operating System Software IOS (tm) 7301 Software (C7301-JS-M), Experimental Version 12.2( :004736) [biff 107] Copyright (c) by cisco Systems, Inc. Compiled Mon 09-Sep-02 18:02 by biff Image text-base:0x600088f8, data-base:0x61a94000 ROM:System Bootstrap, Version 12.2( :200705) [biff-taz2_qa_release_16b 101], DEVELOPMENT SOFTWARE BOOTLDR:7301 Software (C7301-BOOT-M), Experimental Version 12.2( :014224) [biff-taz2_qa_release_17b 101] 7301p2b uptime is 0 minutes System returned to ROM by reload at 00:01:51 UTC Sat Jan System image file is "tftp:// /tazii/images/c7301-js-mz" cisco 7301 (NPE-G1) processor (revision A) with K/32768K bytes of memory. Processor board ID 0 BCM1250 CPU at 700Mhz, Implementation 1, Rev 0.2, 512KB L2 Cache 1 slot midplane, Version 2.0 Last reset from power-on Bridging software. X.25 software, Version SuperLAT software (copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. 3 Gigabit Ethernet/IEEE interface(s) 509K bytes of non-volatile configuration memory K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes) K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x102 Displaying the Configuration Register While Running ROM Monitor If the bootstrap prompt >, the o command displays the virtual configuration register currently in effect. It includes a description of the bits. See the following sample output: >o Configuration register + 02x100 at last boot Bit# Configuration register option settings: 15 Diagnostic mode disabled 14 IP broadcasts do not have network numbers 13 Boot default ROM software if network boot fails Console speed is 9600 baud 10 IP broadcasts with ones C-5

51 Setting the Configuration Register While Running Cisco IOS Appendix C Configuration Register Information 09 Do not use secondary bootstrap 08 Break disabled 07 OEM disabled 06 Ignore configuration disabled 05 Fast boot disabled 04 Fan boot disabled Boot to ROM monitor If the prompt is rommon1, the confreg command displays the virtual configuration register currently in effect. It includes a description of the bits. See the following sample output: rommon 1 > confreg Configuration Summary enabled are: load rom after netboot fails console baud: 9600 boot: the ROM Monitor Do you wish to change the configuration? y/n [n] Setting the Configuration Register While Running Cisco IOS The configuration register can be set in the configuration mode with the config-register 0x<value> command. See the following sample output: Router# config t Enter configuration commands, one per line. End with CNTRL/Z. Router(config)#config-register 0x2142 Router(config)#end Router# %SYS-5-CONFIG_I: Configured from console by console Setting the Configuration Register While Running ROM Monitor If the prompt is >, the or0x<value> command sets the configuration register. See the following sample output: >o/r 0x2102 > If the prompt is rommon1, the confreg command sets the configuration register. It prompts the user about each bit. See the following sample output: rommon 1 > confreg Confiuration Summary enabled are: load rom after netboot fails console baud: 9600 boot: the ROM Monitor do you wish to change the configuration y/n [n]: y enable diagnostic mode? y/n [n]: n enable use net in IP bcast address? y/n [n]: n disable use rom after netboot fails? y/n [n]: n enable use all zero broadcast? y/n [n]: n enable break/abort has effect? y/n [n]: n C-6

52 Appendix C Configuration Register Information Setting the Configuration Register While Running ROM Monitor enable ignore system config info? y/n [n]: n change console baud rate? y/n [n]: n change the boot characteristics? y/n [n]:y enter to boot: 0 = ROM Monitor 1 = the boot helper image 2-15 = boot system [0]: 2 Configuration Summary: enabled are: load rom after netboot fails console baud: 9600 boot: image sepcified by the boot system commands or default to: cisco2-c7301 do you wish to change the configuration? y/n [n] n You must reset or power cycle for new config to take effect rommon 2 > C-7

53 Setting the Configuration Register While Running ROM Monitor Appendix C Configuration Register Information C-8

54 APPENDIXD Repacking the Cisco 7600 Series Router This appendix provides repacking and shipping instructions for the following routers if you need to return your switch to the factory: Cisco 7603 Router, page D-1 Cisco 7606 Router, page D-2 Cisco 7609 Router and Cisco 7609-S Router, page D-4 Cisco 7613 Router, page D-6 Cisco 7603 Router Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Lift the unit only by using handles that are an integral part of the chassis, or by grasping the chassis underneath its lower edge. If you need to return or move the Cisco 7603 Router, follow these steps to repack the switch using the original packaging material: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Set the chassis on the packing material on the bottom pallet. (See Figure D-1.) Place the packing material on the sides of the chassis. Place the top packing material over the top of the switch. Place the accessory kit on the top packing material. Place the shipping carton so the open end is on one side and the glue joint is at the top; slide the pallet into the carton horizontally. Seal the carton with packing tape. D-1

55 Cisco 7606 Router Appendix D Repacking the Cisco 7600 Series Router Figure D-1 Cisco 7603 Router Packing Material Packing foam Documentation and accessories in poly bag Packing foam Packing carton Cisco 7606 Router Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Lift the unit only by using handles that are an integral part of the chassis, or by grasping the chassis underneath its lower edge. If you need to return or move the Cisco 7606 Router, follow these steps to repack the switch using the original packaging material: Step 1 Step 2 Step 3 Set the chassis on the packing material on the bottom pallet. (See Figure D-2.) Place the top-packing material over the top of the chassis. Place the accessory kit on the top-packing material. Note You must include the accessory kit for the final packaging to fit properly. D-2

56 Appendix D Repacking the Cisco 7600 Series Router Cisco 7606 Router Step 4 Step 5 Step 6 Place the outside carton over the entire package. Fold the outside carton down over the top and seal with packing tape. Wrap three packing straps tightly around the top and bottom of the package to hold the outside carton and the bottom pallet together. (See Figure D-3.) Figure D-2 Cisco 7606 Router Packing Material Docs and accessories go in here Top packing material Cisco 7606 chassis D-3

57 Cisco 7609 Router and Cisco 7609-S Router Appendix D Repacking the Cisco 7600 Series Router Figure D-3 Cisco 7606 Router Final Package Cisco 7609 Router and Cisco 7609-S Router Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Lift the unit only by using handles that are an integral part of the chassis, or by grasping the chassis underneath its lower edge. If you need to return or move the Cisco 7609 router or the Cisco 7609-S router, follow these steps to repack the switch using the original packaging material: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Install the power supplies in the chassis. Set the chassis on the packing material on the bottom pallet. (See Figure D-4.) Place the packing bag over the chassis. Place the top-packing material over the top of the chassis. Place the outside carton over the entire package. Place the cable management kit and the accessory kit on the top-packing material. Note You must include the accessory kit for the final packaging to fit properly. D-4

58 Appendix D Repacking the Cisco 7600 Series Router Cisco 7609 Router and Cisco 7609-S Router Step 7 Step 8 Place the top carton over the top. Wrap three packing straps tightly around the top and bottom of the package to hold the outside carton and the bottom pallet together. (See Figure D-5.) Figure D-4 Cisco 7609 Router Packing Material Accessory kit Cable management kit Top packing material D-5

59 Cisco 7613 Router Appendix D Repacking the Cisco 7600 Series Router Figure D-5 Cisco 7609 Router Final Package Cisco 7613 Router Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Lift the unit only by using handles that are an integral part of the chassis, or by grasping the chassis underneath its lower edge. If you need to return or move the Cisco 7613 Router, follow these steps to repack the switch using the original packaging material: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Set the chassis in the bottom pallet. (See Figure D-6.) Place the packing bag over the chassis. Place the front-packing material and power supply packing material around the chassis. Place the power supplies in the spaces provided in the power supply packing material. (See Figure D-6.) Place the top-packing material over the top of the chassis and power supplies. Place the rack-mount kit and the accessory kit on the top-packing material. Note You must include the accessory kit for the final packaging to fit properly. D-6

60 Appendix D Repacking the Cisco 7600 Series Router Cisco 7613 Router Step 7 Step 8 Step 9 Place the outside carton over the entire package. Fold the outside carton down over the top and seal with packing tape. Wrap three packing straps tightly around the top and bottom of the package to hold the outside carton and the bottom pallet together. (See Figure D-7.) Figure D-6 Cisco 7613 Router Packing Material Top packing material Docs and accessories go in here Power supply(s) go in here D-7

61 Cisco 7613 Router Appendix D Repacking the Cisco 7600 Series Router Figure D-7 Cisco 7613 Router Final Package D-8

62 APPENDIXE Cisco 7606-S DC Power Supply Configurations The Cisco 7606-S router accepts two DC power supplies: 2700 W DC-input power supply 4500 W DC-input power supply You can configure the DC power supplies in the Cisco 7606-S router as follows: 2700 W DC-input power supplies in both shelves W DC-input power supplies in both shelves. A 2700 W DC-input power supply in the upper shelf and a 4500 W DC-input power supply in the lower shelf. To configure the Cisco7606-S V01 and the Cisco7606-V V02 chassis to use the 2700 W DC-input power supply and the 4500 W DC-input power supply, you must use the booster bracket (Part Number ) and the slim bracket (Part Number ). The PID for the slim bracket is KIT-MNTG-4500W06S=. The PID for booster bracket is KIT-MNTG-2700W06S=. Identifying Chassis Version in the Supported Line Card You can use either of the following methods to identify the chassis version in the supported router: Product Identification Label on the router: - Displays the labels of all the supported chassis. For example, the PID label Cisco7606-S V01 specifies that the chassis version is 01. Show inventory command in the command line interface: - Displays the version ID of all the supported chassis. Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Cisco 7606-S V01 Configuration with Two 2700 W DC Power Supplies This chassis uses booster bracket (Part Number ) to support the power supplies. You do not have to change anything. E-1

63 Cisco 7600 Series Cisco 7606-S V01 Configuration with Two 4500 W DC Power Supplies Appendix E Cisco 7606-S DC Power Supply Configurations Cisco 7606-S V01 Configuration with Two 4500 W DC Power Supplies Note This configuration requires you to remove the old booster brackets (Part Number ) and replace them with the slim brackets (Part Number ). To do this, proceed as follows: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Remove the power supplies as described in Removing PWR-2700-DC Power Supply from a Cisco 7606-S Router, page Remove the two screws (Part Number ) securing the bracket (Part Number ) at the top slot and remove the bracket. See Figure E-1. Remove the two screws (Part Number ) securing the bracket (Part Number ) at the lower slot and remove the bracket. See Figure E-1. Use the screws (Part Number ) removed in Step 1 to install the slim bracket (Part Number ) at the top slot. See Figure E-2. Use the screws (Part Number ) removed in Step 2 to install the slim bracket (Part Number ) at the bottom slot. See Figure E-2. Install the 4500 W DC in the upper and lower shelves as described in Installing a PWR-4500-DC Power Supply in a Cisco 7606-S Router, page Figure E-1 Removing Fat Brackets E-2

64 Cisco 7600 Series Appendix E Cisco 7606-S DC Power Supply Configurations Cisco 7606-S V01 Configuration with a 2700 W DC Power Supply and a 4500 W DC Power Supply Figure E-2 Installing Slim Brackets Cisco 7606-S V01 Configuration with a 2700 W DC Power Supply and a 4500 W DC Power Supply This configuration requires you to remove the booster brackets (Part Number ) and replace them with the slim brackets (Part Number ). To do this, proceed as follows: Step 1 Remove the power supplies as described in Removing a DC-Input Power Supply, page 5-9. Note Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 When you are using a PWR-2700-DC and a PWR-4500-DC, you must install the PWR-4500-DC supply in the lower slot. Remove the two screws (Part Number ) securing the bracket (Part Number ) at the top slot and remove the bracket. See Figure E-1. Remove the two screws (Part Number ) securing the bracket (Part Number ) at the lower slot and remove the bracket. See Figure E-1. Use the screws (Part Number ) removed in Step 1 to install the slim bracket (Part Number ) at the top slot. See Figure E-2. At the top slot, use three screws (Part Number ) to install the booster bracket (Part Number ). See Figure E-3. Install the 2700 W DC power supply in the top slot as described in Installing a PWR-2700-DC Power Supply in a Cisco 7606-S Router, page Install the 4500 W DC in the lower shelves as described in Installing a PWR-4500-DC Power Supply in a Cisco 7606-S Router, page E-3

65 Cisco 7600 Series Cisco 7606-S V02 Configuration with Two 2700 W DC Power Supplies Appendix E Cisco 7606-S DC Power Supply Configurations Figure E-3 Installing Booster Bracket Cisco 7606-S V02 Configuration with Two 2700 W DC Power Supplies This configuration requires you to do nothing as this version of the Cisco 7606-S router already has the slim brackets (Part Number ) and the booster brackets (Part Number ). Cisco 7606-S V02 Configuration with Two 4500 W DC Power Supplies This configuration requires you to remove both upper and lower booster brackets Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Remove the power supplies from the top slot and the lower slot as described in Removing PWR-2700-DC Power Supply from a Cisco 7606-S Router, page Remove three screws (Part Number ) securing the booster bracket (Part Number ) at the top slot. See Figure E-4. Push the booster bracket (Part Number ) backward and then lift and remove it from the chassis. Remove three screws (Part Number ) securing the booster bracket (Part Number ) at the bottom slot. See Figure E-4. Push the booster bracket (Part Number ) backward and then lift and remove it from the chassis. Install the 4500 W DC in the top slot as described in Installing a PWR-4500-DC Power Supply in a Cisco 7606-S Router, page E-4

66 Cisco 7600 Series Appendix E Cisco 7606-S DC Power Supply Configurations Cisco 7606-S V02 Configuration with a 2700 W DC Power Supply and a 4500 W DC Power Supply Step 7 Install the 4500 W DC in the lower slot as described in Installing a PWR-4500-DC Power Supply in a Cisco 7606-S Router, page Figure E-4 Removing Booster Brackets Cisco 7606-S V02 Configuration with a 2700 W DC Power Supply and a 4500 W DC Power Supply This configuration requires you to remove the lower booster bracket (Part Number ). Step 1 Remove the PWR-2700-DC power supply from the lower slot as described in Removing PWR-2700-DC Power Supply from a Cisco 7606-S Router, page Note Step 2 Step 3 Step 4 When you are using a PWR-2700-DC and a PWR-4500-DC, you must install the PWR-4500-DC supply in the lower slot. Remove three screws (Part Number ) securing the booster bracket (Part Number ) at the bottom slot See. Figure E-4. Push the booster bracket (Part Number ) backward and then lift and remove it from the chassis. Install the 4500 W DC in the lower slot as described in Installing a PWR-4500-DC Power Supply in a Cisco 7606-S Router, page E-5

67 Cisco 7600 Series Appendix E Cisco 7606-S V02 Configuration with a 2700 W DC Power Supply and a 4500 W DC Power Supply Cisco 7606-S DC Power Supply Configurations Figure E-5 Removing Lower Booster Bracket E-6

68 INDEX Numerics 1400 W power supply specifications A W power supply specifications A-10, A W power supply specifications A W power supply specifications A-11, A W power supply specifications A W power supply specifications A W power supply specifications A W power supply specifications A-9 Cisco 7609 Internet Router A-7 Cisco 7613 Internet Router A-8 direction 1-19 altitude, environmental specifications Cisco 7603 Internet Router A-2, A-3 Cisco 7604 Router A-4 Cisco 7606 Internet Router A-4, A-5 Cisco 7609 Internet Router A-6, A-7 Cisco 7613 Internet Router A-8 audience 1-ix A accessory kit, console port B-7 AC-input PEM installing removing AC-input power supplies heat dissipation 2-6, 2-7, 2-17, 2-18, 2-20 AC-input power supply installing 5-7 LEDs 1-32, 4-3 removing 5-3 troubleshooting 4-3 adapters console port mode 2 B-10 DB-25 B-9 DB-9 B-8 modem B-9 airflow Cisco 7603 Internet Router A-2, A-3 Cisco 7604 Router A-4 Cisco 7606 Internet Router A-5, A-6 B bandwidth 1-16 C cable management system (Cisco 7609 Internet Router) installing 3-15 replacing the cable guide 3-17 cabling, console ports B-7 chassis installation, guidelines 3-3 checklist, site planning 2-34 Cisco 7603 Internet Router architecture 1-2, 1-3, 1-5 chassis, dimensions A-2, A-3 fan assembly installing removing PEM installation procedure, AC-input installation procedure, DC-input removal procedure, AC-input OL IN-1