(ATX12V) Uninterrupted Switching Power Supply Technical Specification

Size: px

Start display at page:

Download "(ATX12V) Uninterrupted Switching Power Supply Technical Specification"

Ezra Black
5 years ago
Views:

1 AUP-X-400-V4 (ATX12V) Uninterrupted Switching Power Supply Technical Specification Part No. REVISION HISTORY VERSION RELEASE DATE NOTES DATE 1. MAR-2011 IMPROVE THE EFFICIENCY NOT LESS THAN 80% AND COMPLAIN WITH EN :2006+A11: /3/17 PAGE : 1 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

2 CONTENTS 1. INTRODUCE SCOPE RELATED DOCUMENTS IMPORTANT NOTICE BEFORE INSTALL APPLICABLE DOCUMENTS ELECTRICAL SPECIFICATION AC Input Voltage Frequency Inrush Current AC Input Current Efficiency Output Requirements Output Regulations DC Load Requirements Cross Regulation V Standby Voltage DC Output Voltage Ripple And Noise Total Output Power Remote ON/OFF Control Power Sequence Power on Time (T1) Rise Time (T2) Power Good Delay Time (T3) Power Good Rise Time (T4) Hold Up Time (T5) Power Fail Signal (T6) USPS Timing Chat Protections Over Voltage Protection Short Circuit Protection Protection Reset Over Shoot Over Power Protection MECHANICAL SPECIFICATION USPS MAIN BODY PHYSICAL DIMENSION AC INPUT CONNECTOR DC OUTPUT CONNECTOR 14 PAGE : 2 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

3 8. BATTERY PACK MECHANICAL SPECIFICATION PHYSICAL DIMENSION BATTERY PACK PANEL BATTERY PAC WIRES CONFIGURATION & CONNECTOR LED INDIACTION AND ALARM TABLE BATTERY PACK INSIDE CONNECTION BATTERY SPECIFICAITON COMMUNICATION PORT AND RUPS 2000 BACKUP UTILITY HARDWARE CONFIGURATION COMMUNICATION PORT PIN ASSIGNMENT SELECT SUITABLE COMMUNICATE CABLE FOR YOUR PC SYSTEM S RS-232 PORT RUPS 2000 PACKAGE USING THE UPS MONITORING PROGRAM THAT COMES WITH WINDOWS XP Environment Operation/Storage Temperature Range Humidity Safety EMI Requirements Dielectric Voltage Withstand (HI-POT) PFC Electrostatic Discharge Requirement (ESD) EFT/Burst Surge Burn-In MTBF PAGE : 3 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

4 1. INTRODUCE 1.1 SCOPE THIS SPECIFICATION DESCRIBES THE PERFORMANCE CHARACTERISTICS OF AUP-X-400-V4 USPS (UNINTERRUPTED SWITCHING POWER SUPPLY) PRODUCT, WHICH IS A 400WATT, 7 OUTPUTS SWITCHING POWER SUPPLY IN EPS12V FORM FACTOR WITH BATTERY BACKUP FUNCTION. THE AUP-X-400-V4 IS BASED ON ATX / PS/2 FORM FACTOR DESIGNED TO MEET THE MOST OF INTEL AND AMD COMPUTER REQUIREMENTS. 1.2 RELATED DOCUMENTS THIS DOCUMENT IS BASED ON THE SPECIFICATIONS LIST IN BELOW TABLE, WITH EXCEPTIONS AS DESCRIBED IN THE BODY OF THIS DOCUMENT. FOLLOW INTEL ATX12V POWER SUPPLY DESIGN GUIDE TO UPDATE SPECIFICATION, SUCH AS POWER, CURRENT, EFFICIENCY, CONNECTORS ETC. DOCUMENT TITLE ATX12V POWER SUPPLY DESIGN GUIDE 2. IMPORTANT NOTICE BEFORE INSTALL 1. TO FULLY CHARGE THE BATTERY FOR THE FIRST TIME IT IS USED, ALLOW THE POWER CORD TO REMAIN PLUGGED IN A FULL 24 HOURS. NORMAL TIME TO RECHARGE THE BATTERY TO ITS FULL CAPACITY IS 5 ~ 8 HOURS. 2. IF THERE IS A DEFECT IN THE BATTERY PACK, THE BATTERY BACKUP WILL NOT FUNCTION. CONTACT YOUR SUPPLIER OR TECHNICAL ENGINEER. ( BUT, SWITCHING POWER SUPPLY STILL CAN FUNCTION WITH AC POWER LINE. ) 3. APPLICABLE DOCUMENTS THE FOLLOWING DOCUMENTS FORM A PART OF THIS SPECIFICATION TO THE EXTEND SPECIFIED: EUROPEAN STANDARDS EN : A11 : 2009 EN : 2005 BASIC AND INTERNATIONAL STANDARDS IEC : 2005 IEC : 2005 EN : A1 : 2006 EN : 2006 EN : 2008 IEC : A1 : 2005 IEC : 2006 IEC : 2007 EST STANDARDS : EN : A1 : 2007, CLASS B EN55024 : A1 : A2 : 2003 IEC :2008 EN : 2006 IEC : A1 : 2007 IEC : 2004 EN : A1 : A2 : 2005 IEC : 2005 IEC A1 : A2 : 2006 IEC : A1 : 2000 IEC : 2004 PAGE : 4 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

5 4. ELECTRICAL SPECIFICATION UNLESS OTHERWISE NOTED, THE ELECTRICAL REQUIREMENTS SPECIFIED HEREIN SHALL ACCORD WITH THE ENVIRONMENTAL LIMITS FOR NORMAL OPERATION DEFINED IN SECTION 7 OF THIS DOCUMENT. ITEM APOLLO USPS AUP-X-400-V4 CAPACITY 400W INPUT VOLTAGE 90~260VAC AUTO VOLTAGE SELECTED INPUT FREQUENCY 60/50HZ POWER FACTOR 0.97 (ACTIVE PFC) SURGE PROTECTION YES OUTPUT DC CURRENT +12 V1 / 16A *1 MAX. CONTINUOUS TOTAL DC OUTPUT +12 V2 / 16A SHALL NOT EXCEED 350W, PEAK 400W) + 5 V / 30 A *2. MAX. COMBINED OUTPUT ON +5V V / 28 A & +3.3V SHALL NOT EXCEED 150W. -12 V / 0.8A -5 V / 0.3A +5V STAND BY / 2.5A BATTERY CHARGER 27.6V/300MA WEIGHT 6 KGS (WITH BP5EP-2410W BATTERY PACK ) USPS MAIN BODY DIMENSION BATTERY PACK DIMENSION AND TYPE DESIGNED INRUSH CURRENT OVER VOLTAGE PROTECTION YES OVER POWER PROTECTION YES >110%~150% OVER CURRENT PROTECTION 150 X 145 X 86 MM BP-5EP 219 X 145 X 42 MM 3, 3.5KGS LEAD ACID (MAINTENANCE FREE) 24V/3AH HRL1210W / 178 X 33.6 X 64 MM3 ( PER UNIT ) MOSFET IC WITH COPYRIGHT HYBRIDE IC DESIGN 80A FOR 230VAC, 60A FOR 115VAC 240VA OF EACH DC OUTPUT UPS Mode / Function Specification (V4.0) CAPACITY 600VA AC INPUT VOLTAGE TRANSFER POINT FROM NORMAL TO BACKUP : 80 / 175 VAC ( UNDERVOLT ) FROM BACKUP TO NORMAL : 90 / 185 VAC AC INPUT VOLTAGE TRANSFER POINT PROTECTION BY FUSE ( OVERVOLT ) TRANSFER TIME 0 MS FOR DC OUTPUT(COMPUTER) SYSTEM BACKUP TIME ( BACKUP FOR A PC SYSTEM ) RECHARGE TIME BATTERY VOLTAGE MONITORING BATTERY ISOLATED IF W/O AC 4.1 AC Input Voltage AT LEAST 1 MINUTES LONGER BACKUP TIME CAN USE OTHER BATTERY PACK 5~8 HOURS LED DISPLAY, BUZZER WHEN AC POWER SOURCE IS NOT AVAILABLE, THE RELAY WILL ISOLATED WITH DC POWER SOURCE TO AVOID THE BATTERY POWER AUTO DISCHARGE. The power supply shall be operated at universal input voltage defined in the following table. lnput Voltage MIN NOM MAX Voltage PAGE : 5 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

6 4.2 Frequency The input frequency range is from 50Hz to 60Hz. 4.3 Inrush Current The max inrush current is 80A for 230VAC / 60A for 115VAC Cold Start Conditions 115/230VAC, full load. 25 ambient. Limits No component over stress or damage should occur to the power supply. Input fuse shall not blow Warm Start Conditions Limits Turn off at 132/264VAC full load for 1 No component over stress or damage sec then turn on at the peak of the input should occur to the power supply. voltage cycle at 25 ambient. Input fuse shall not blow. 4.4 AC Input Current AC Input MAX Units 100~240V 7-4 AMPS 4.5 Efficiency The power supply efficiency shall not be less than 80% at the maximum load of sec. 5.2 and 115/230Vac input voltage. PAGE : 6 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

7 5 Output Requirements 5.1 Output Regulations Output Voltage Range MIN Nominal MAX Units +5V ±5% Volts +12V1 ±5% Volts +12V2 ±5% Volts -5V ±10% Volts -12V ±10% Volts +3.3V ±5% Volts +5Vsb ±5% Volts 5.2 DC Load Requirements Note: 1). The above voltage range should also include ripple and noise. 2). The output voltage should be measured at the terminals of output connector. Output Voltage MIN NOM MAX Units +5V AMPS +12V AMPS +12V AMPS -5V AMPS -12V AMPS +3.3V AMPS +5Vsb AMPS Note : 1). The maximum continuous total DC output power shall not exceed 400 Watts. 2). The maximum continuous combined load on +5V and +3.3V outputs shall not exceed 150 Watts. Combined load on +12V1 and +12V2 outputs shall not exceed 360(30A) Watts. 3). The maximum continuous combined load on +5V, +3.3V and +12V1,+12V2 outputs shall not exceed 380 Watts. 5V and -12V outputs shall not exceed 9.6Watt. PAGE : 7 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

5.3 Cross Regulation The DC loads shall remain within the ranges specified in 5-2 DC Load Requirements and the DC output voltages also shall remain within the regulation ranges specified in 5-1

8 5.3 Cross Regulation The DC loads shall remain within the ranges specified in 5-2 DC Load Requirements and the DC output voltages also shall remain within the regulation ranges specified in 5-1 Output Regulation when measured at the load end of the output connectors V standby voltage The +5Vsb is on whenever the AC power is present. 5.5 DC Output Voltage Ripple and Noise Output Voltage Ripple & Noise Max Units +5V 50 mv +12V1 120 mv +12V2 120 mv -5V 100 mv -12V 120 mv +3.3V 50 mv +5Vsb 50 mv Note : 1)The measurements should be made by crossing a 10uF/ electrolytic and a 0.1uF ceramic disk capacitors at each output with measuring bandwidth from DC to 20 MHz. If ambient temperature is under 20 or over 30, the AC input should be nominal input. 5.6 Total Output Power MAX Units 400 Watts 5.7 Remote ON/OFF Control The power supply outputs shall be enabled with an active-low TTL signal. When TTL signal is low, the DC outputs are to be enabled. PAGE : 8 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

9 When TTL signal is high or open circuited, the DC outputs are to be disabled. Electronic means or a mechanical switch may activate the TTL signal. After the TTL signal is active high, must wait for 3 seconds before active low again. 5.8 Power Sequence AC IN On Off PS_ON T1 T5 95% +12V 10% +5V O/P s +3.3V T2 PG# T3 T4 T6 5.9 Power On Time (T1) MAX Units 500 ms 5.10 Rise Time (T2) Min. MAX. Units ms 5.11 Power Good Delay Time (T3) MIN. MAX. Units ms The test environment is 25 nominal input Power Good Rise Time (T4) MAX Units 10 ms PAGE : 9 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

10 5.13 Hold Up Time (T5) MIN. Units 16 ms The test environment is 25 & full load nominal input Power Fail Signal (T6) Power good signal shall go to a down level 1ms before +5V output voltage falls below the regulation limits during PS-ON signal pull high. MIN. Units 1.0 ms 5.15 USPS TIMING CHAT (A) 2 TURN ON COMPUTER POWER SYSTEM, THE CONDITIONS OF EACH POINT ARE AS BELOW: 1 AC LINE NORMAL PAGE : 10 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

11 3 BATTERY / DC SUPPORT NORMAL 4 5VSB OUTPUT NORMAL 6 REMOTE ON/OFF STAY IN HI CONDITION, IT S ALSO IN STANDBY MODE. WHEN ACTIVE REMOTE ON, 5 DC O/P WILL UP AND 8 PG DELAY FOR 200~350MS THEN IT ALSO UP, THEN THE COMPUTER GO INTO NORMAL OPERATION. (B) (C) (D) (E) IF THE AC LINE HAS ANY CHANGING, BUT TIMING SHORTER THAN 20MS. THEN, IT WON T EFFECT TO DC OUTPUTS AND ALL SIGNALS ARE AS NORMAL. IF THE AC LINE BROWN OUT THAN 20MS, THEN ALL POINTS WILL BE AFFECTED. (FOR RED LINE SHOWS WITHOUT UPS BACKUP) 568 UPS MONITORING SIGNAL WILL SEND AC FAIL, HI TO PC SYSTEM THROUGH RS-232 PORT, MEANWHILE ALL OF DC OUTPUTS ARE BACKUP BY BATTERY PACK TO KEEP STABILE OUTPUTS FOR PC SYSTEM WITHOUT ANY INTERRUPTED. IF THE AC RECOVER, THEN ALL SIGNALS WILL BE RECOVER TO NORMAL, TOO. AND (F) ARE REPEAT ABOVE PROCEDURES. IF 3 DC INPUT ( BATTERY PACK ) VOLTAGE DROP TO 21.5 ± 0.5V, THEN WILL SEND A SIGNAL BATTERY LOW TO PC SYSTEM. IF 3 DC INPUT VOLTAGE DROP TO 18.5 ± 0.5V, THEN WILL SEND A SIGNAL 7 SHUT DOWN TO PC SYSTEM 6. Protections 6.1 Over Voltage Protection When the DC outputs (+5V, +12V1,+12V2, +3.3V) have over voltage condition, the power supply shall provide latch mode over voltage protection. DC output Max Unit +12V1,+12V V +5V 6.5 V +3.3V 4.6 V 6.2 Short Circuit Protection A short circuit placed to ground shall cause no damage or power supply shall be shutdown. (The contact resistance is 0.05 ohm when the outputs short circuit.) 6.3 Protection Reset When the power supply latches into shutdown condition due to a fault on an+5v,+3.3v,+12v1,+12v2 output(ocp, OVP, UVP), the protection shall reset after the fault has been removed, use remote on/off control or recycle the AC power again for a typical of 5 seconds. PAGE : 11 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

12 6.4 Over Shoot Any output overshoot at turn on shall be less than 15% of the nominal output value (with resistive load) as described in sec Over Power Protection At 115/230Vac input the power supply will shut down all DC output within 110% to 150% of full load. PAGE : 12 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

13 7. MECHANICAL SPECIFICATION 7.1 USPS MAIN BODY PHYSICAL DIMENSION W150*H86*D140 (MM) 7.2 AC INPUT CONNECTOR THE AC INPUT RECEPTACLE SHALL BE AN IEC 320 C14 TYPE OR EQUIVALENT. PAGE : 13 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

14 7.3 DC CONNECTOR EPS12V/ AX 12V MAIN POWER CONNECTOR: MAIN POWER CONNECTOR (P1) / CABLE (L1) : CONNECTOR: MOLEX OR EQUIVALENT (MATING MOTHERBOARD CONNECTOR IS MOLEX OR EQUIVALENT) PIN COLOR SIGNAL AWG PIN COLOR SIGNAL AWG 1 ORANGE +3.3VDC ORANGE +3.3VDC 16 BROWN +3.3VS ORANGE +3.3VDC BLUE -12VDC 18 3 BLACK COM BLACK COM 16 4 RED +5VDC GREEN PS_ON# 22 5 BLACK COM BLACK COM 16 6 RED +5VDC BLACK COM 16 7 BLACK COM BLACK COM 16 8 GRAY PWR_OK N/C PURPLE +5VSB RED +5VDC YELLOW +12V1DC 16 +5VDC RED +12VS VS YELLOW +12V1DC RED +5VDC ORANGE +3.3VDC BLACK COM 16 Cable L1: 550+/-20mm VS. : REMOTE SENSE SIGNAL DOUBLE CRIMPED WITH DC OUTPUT VOLTAGECONTACT. FOR ATX12V PLEASE USE 20 PIN CONNECTOR. FOR EPS12V PLEASE USE 24 PIN CONNECTOR PROCESSOR POWER CONNECTOR (P14) / CABLE (L14) CONNECTOR: 8 PIN MOLEX OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 BLACK COM 16 2 BLACK COM 16 3 BLACK COM 16 4 BLACK COM 16 5 YELLOW/BLACK +12V2DC 16 6 YELLOW/BLACK +12V2DC 16 7 YELLOW/BLACK +12V2DC 16 8 YELLOW/BLACK +12V2DC 16 L14 (UL1007) 550 +/-10 MM PAGE : 14 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

15 7.3.3 PROCESSOR POWER CONNECTOR (P15) / CABLE (L15) CONNECTOR: 6 PIN MOLEX OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 YELLOW/BLACK +12V2DC 16 2 YELLOW/BLACK +12V2DC 16 3 YELLOW/BLACK +12V2DC 16 4 BLACK COM 16 5 BLACK COM 16 6 BLACK COM 16 L14 (UL1007) 550 +/-10 MM V1 POWER CONNECTOR (P11) / CABLE (L11) CONNECTOR: MOLEX OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 BLACK COM 16 2 BLACK COM 16 3 YELLOW/BLACK +12V2DC 16 4 YELLOW/BLACK +12V2DC 16 L11 (UL1007) 550 +/- 10 MM PERIPHERAL CONNECTOR(S) P2 / CABLE (L2) CONNECTOR: AMP OR MOLEX P OR EQUIVALENT. PIN COLOR SIGNAL AWG CABLE 1 YELLOW +12V1DC 18 2 BLACK COM 18 3 BLACK COM 18 4 RED +5VDC 18 L2 (UL1007) 550 +/-10 MM L2+(UL1007) 150 MM FLOPPY DRIVE CONNECTOR P3 / CABLE (L3) CONNECTOR: AMP OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 RED +5VDC 20 2 BLACK COM 20 3 BLACK COM 20 4 YELLOW +12V2DC 20 L3 (UL1007) 150MM SERIAL ATA POWER CONNECTOR (P13) / CABLE (L13) CONNECTOR: MOLEX OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 YELLOW +12V1DC 18 2 BLACK COM 18 3 RED +5VDC 18 4 BLACK COM 18 5 ORANGE +3.3VDC 18 L13 (UL1007) 550 +/-10 MM L13+(UL1007) 200MM PAGE : 15 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

7.1.1 BACKUP DC INPUT CONNECTOR (P4) / CABLE (L4) CONNECTOR: TKP H7619P-02 OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 RED BAT + VE 16 2 BLACK BAT -VE 16 L4 150MM UL1007 7.3.

16 7.1.1 BACKUP DC INPUT CONNECTOR (P4) / CABLE (L4) CONNECTOR: TKP H7619P-02 OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 RED BAT + VE 16 2 BLACK BAT -VE 16 L4 150MM UL LED DISPLAY CONNECTOR (P5) / CABLE (L5) CONNECTOR: TKP OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 YELLOW LED ORANGE LED RED LED L5 150MM (UL1007) 5 BLACK COM COMMUNICATE PORT CONNECTOR (P7) / CABLE (L7) CONNECTOR: TKP OR EQUIVALENT PIN COLOR SIGNAL AWG CABLE 1 YELLOW BAT. LOW 22 2 ORANGE GND 22 3 RED SHUTDOWN 22 4 BROWN GND 22 5 GREEN AC FAIL 22 L7 150MM (UL1007) COMMUNICATE PORT CONNECTION CABLE (P7+ TO DB9) P7+ CONNECTOR: TKP P OR EQUIVALENT / CABLE : L7+ TO DB9, 450MM (UL1007) DB9 DB9 PIN COLOR SIGNAL AWG P7+ PIN P7+ 1 BROWN BAT. LOW RED GND ORANGE SHUTDOWN YELLOW GND GREEN AC FAIL PAGE : 16 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

7.3.11 COMMUNICATE PORT CONNECTION CABLE (P7+ TO IDE A) (OPTION) P7+ CONNECTOR: TKP 7755-6P OR EQUIVALENT / CABLE : L7+ TO IDE A, 450MM (UL1007) IDE A PIN COLOR

17 COMMUNICATE PORT CONNECTION CABLE (P7+ TO IDE A) (OPTION) P7+ CONNECTOR: TKP P OR EQUIVALENT / CABLE : L7+ TO IDE A, 450MM (UL1007) IDE A PIN COLOR SIGNAL AWG P7+ PIN P7+ 1 BROWN BAT. LOW RED GND ORANGE SHUTDOWN YELLOW GND GREEN AC FAIL COMMUNICATE PORT CONNECTION CABLE (P7+ TO IDE B) (OPTION) P7+ CONNECTOR: TKP P OR EQUIVALENT / CABLE : L7+ TO IDE B, 450MM (UL1007) IDE B PIN COLOR SIGNAL AWG P7+ PIN P7+ 1 BROWN BAT. LOW RED GND ORANGE SHUTDOWN YELLOW GND GREEN AC FAIL PAGE : 17 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

7.3.13 COMMUNICATE PORT CONNECTION CABLE (P7+ TO CN1 OF INTERFACE BOARD) (OPTION) P7+ CONNECTOR: TKP 7755-6P OR EQUIVALENT / CABLE : L7+ TO H110-5, 2.

18 COMMUNICATE PORT CONNECTION CABLE (P7+ TO CN1 OF INTERFACE BOARD) (OPTION) P7+ CONNECTOR: TKP P OR EQUIVALENT / CABLE : L7+ TO H110-5, 2.00, 450MM (UL1007) 5 PIN COLOR SIGNAL AWG P7+ PIN P7+ 1 BROWN BAT. LOW RED GND ORANGE SHUTDOWN YELLOW GND GREEN AC FAIL INTERFACE BOARD FOR USB B TYPE PORT PAGE : 18 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

8. BATTERY PACK MECHANICAL SPECIFICATION 8.1 PHYSICAL DIMENSION : L219 X W145 X H41.5 (MM) 8.2 BATTERY PACK PANEL 8.2.1 THE L6+ CABLE OF USPS MAIN BODY HAS A MAIN SWITCH.

19 8. BATTERY PACK MECHANICAL SPECIFICATION 8.1 PHYSICAL DIMENSION : L219 X W145 X H41.5 (MM) 8.2 BATTERY PACK PANEL THE L6+ CABLE OF USPS MAIN BODY HAS A MAIN SWITCH. THIS MAIN SWITCH SHOULD INSTALL AT SUITABLE PLACE OF PC CHASSIS AND THE PC SYSTEM HAS A TURN ON/OFF SWITCH ON THE CHASSIS FRONT PANEL PLEASE SWITCH THIS MAIN SWITCH TO I POSITION PUSH THE TURN ON/OFF SWITCH, THEN THE PC SYSTEM WILL START TO WORK. PAGE : 19 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

20 8.3 BP-5EP BATTERY PACK WIRES CONFIGURATION & CONNECTOR BACKUP DC INPUT CONNECTOR (P4+) / CABLE (L4+) CONNECTOR: TKP H7619R-02 OR EQUIVALENT CONNECTOR: CABLE UL1007 SIGNAL COLOR AWG 1 BAT +VE RED MM 2 BAT -VE BLACK MM LED DISPLAY CONNECTOR (P5+) / CABLE (L5+) CONNECTOR: TKP 7755P-05 OR EQUIVALENT PIN SIGNAL COLOR AWG CABLE 1 LED1 YELLOW 22 2 LED2 ORANGE 22 3 LED3 RED 22 4 L5 150MM (UL1007) 5 COM BLACK LED INDICATION AND ALARM TABLE UTILITY STATES LED INDUCTOR STATE BUZZER STATE NORMAL BLACKOUT, UPS ON (24~21.5V) BATTERY LOW (21.5~18.5V) BEEP.. BEEP.. BEEP.. ( 3 SECONDS INTERVAL ) BEEP ( SOUNDS QUICKLY AND SHORT ) AC NORMAL / BATTERY FAIL PAGE : 20 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

21 8.5 BATTERY PACK INSIDE CONNECTION 8.6 BATTERY SPECIFICATION PAGE : 21 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

2 SELECT SUITABLE COMMUNICATE CABLE FOR YOUR PC SYSTEM S RS-232 PORT USPS OFFER THREE CABLES FOR INTERNAL AND EXTERNAL TYPE RS-232,

22 9 COMMUNICATION PORT AND RUPS 2000 BACKUP UTILITY HARDWARE CONFIGURATION 9.1 COMMUNICATION PORT PIN ASSIGNMENT PIN RS-232 USPS 1 DCD BATTERY LOW 3 TXD GND 4 DTR SHUTDOWN 7 RTS GND 8 CTS AC FAIL 9.2 SELECT SUITABLE COMMUNICATE CABLE FOR YOUR PC SYSTEM S RS-232 PORT USPS OFFER THREE CABLES FOR INTERNAL AND EXTERNAL TYPE RS-232, YOU ONLY NEED TO CHOICE ONE OF THEM FOR YOUR PC SYSTEM. FOR DB9 PORT, PLEASE CONNECT THE DB9 PIN TO PIN CABLE TO CONNECT WITH EXTERNAL RS-232 PORT! PAGE : 22 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

23 9.3 RUPS 2000 PACKAGE : 1. DB9 PORT PIN TO PIN CABLE 2. USB-B TO USB-A CABLE 3. RS-232 TO USB INTERFACE BOARD 4. CD DISKETTE WITH SOFTWARE BACKUP UTILITY FOR WINDOWS SERIES, DOS, LINUX, NOVELL USER MANUAL FOR MORE DETAIL OF RUPS 2000, PLEASE REFER THE USER MANUAL! PAGE : 23 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

SERIAL PORT ON THE COMPUTER. 10.2 TURN THE USPS ON AND START THE COMPUTER. 10.3 ONCE THE COMPUTER HAS STARTED, CLICK ON START, THEN CONTROL PANEL.

24 10 Using the UPS Monitoring Program That Comes With Windows XP ( For Window 7, please use RUPS 2000 V4.2 version ) 10.1 WITH THE COMPUTER AND THE USPS OFF, CONNECT THE SERIAL PORT CONNECTION CABLE BETWEEN USPS MAIN BODY DB9 PORT AND AN OPEN RS-232 SERIAL PORT ON THE COMPUTER TURN THE USPS ON AND START THE COMPUTER ONCE THE COMPUTER HAS STARTED, CLICK ON START, THEN CONTROL PANEL IN THE CONTROL PANEL, DOUBLE-CLICK ON POWER OPTIONS CLICK THE UPS TAB. PAGE : 24 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

10.6 CLICK THE SELECT BUTTON 10.7 SET THE MANUFACTURER TO GENERIC. 10.8 SELECT THE COM PORT THAT THE USPS IS CONNECTED TO.

25 10.6 CLICK THE SELECT BUTTON 10.7 SET THE MANUFACTURER TO GENERIC SELECT THE COM PORT THAT THE USPS IS CONNECTED TO CLICK ON CUSTOM SO IT IS HIGHLIGHTED LICK THE NEXT BUTTON. PAGE : 25 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

26 10.11 ET THE UPS SIGNAL POLARITY AS SHOWN BELOW LICK THE FINISH BUTTON LICK THE CONFIGURE BUTTON. PAGE : 26 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

27 10.14 ECONDS BETWEEN POWER FAILURE AND FIRST NOTIFICATION - THIS IS THE TIME BETWEEN WHEN THE POWER FAILS AND THE UPS STARTS BEEPING. SECONDS BETWEEN SUBSEQUENT POWER FAILURE NOTIFICATIONS - THIS IS THE TIME BETWEEN BEEPS DURING A POWER FAILURE INUTES ON BATTERY BEFORE CRITICAL ALARM - THIS DETERMINES HOW LONG THE UPS WILL RUN BEFORE THE OPERATING SYSTEM STARTS TO SHUT DOWN. IF LEFT BLANK, THE UNIT WILL RUN UNTIL THERE IS APPROXIMATELY 2 MINUTES OF BACKUP TIME REMAINING, THEN THE OPERATING SYSTEM WILL START TO SHUT DOWN EXT, INSTRUCT THE COMPUTER TO: - LEAVE AS "SHUT DOWN" INALLY, TURN OFF THE UPS. - IF CHECKED, THIS WILL ALLOW THE UPS TO BE TURNED OFF AUTOMATICALLY ONCE THE OPERATING SYSTEM IS SHUT DOWN LICK THE OK BUTTON LICK THE APPLY BUTTON PAGE : 27 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

28 11. Environment 11.1 Operation/Storage Temperature Range Operation : 5 to 50 (nominal input) Storage : -40 to 70 LOAD 100% 80% Humidity (none condensing) Operation: 20% to 85% RH(nominal input) Storage : 10% to 95% RH 12. Safety UL CE EN : 2006, + A11: EMI REQUIREMENTS CE FCC part 15 sub part J class B at system load CISPR 22 CLASS B 14. Dielectric Voltage Withstand (HI-POT) The power supply shall withstand for 3 seconds minute without breakdown the application of an 1800Vac-supply voltage applied between both input line and chassis (10mA AC Cutoff current). Isolating transformers shall similarly withstand 4242Vdc applied between both primary and secondary windings for a minimum of one minute. 15. PFC Active Power Factor Correction, complies with EN : 1995+A1+A2:1998, Class D. 16. Electrostatic Discharge (ESD) Comply with IEC EFT/ Burst Comply with IEC Surge Comply with IEC PAGE : 28 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

temperature of 25. 21. Label Label 1 : USPS Main Body Main Label Label 2 : USPS Main Body Label for Serial No.

29 19. Burn-In Applying 115 Vac ± 10 % or 230 Vac ± 10% input voltage and maximum load (80%) for this product in 45 ± 5 chamber. 20. M.T.B.F. The power supply shall have a minimum mean time between failure greater than 100,000 hours at continuous operation of 100% load and an ambient temperature of Label Label 1 : USPS Main Body Main Label Label 2 : USPS Main Body Label for Serial No. Label 3 : Battery Pack Label, Same as Label 2 format. REMARK : ALL OF INFORMATION ARE ONLY FOR REFERENCE, THE CORRECT INFORMATION WILL BE CONFIRM AGAIN WITH CUSTOMER. PAGE : 29 / 29 AUP-X-400-V4 (BP-5EP) ATX12V

120 WATT FLEX ATX TYPE WITH ACTIVE PFC

120 WATT FLEX ATX TYPE WITH ACTIVE PFC FXA120-W-F SERIES GENERAL SPECIFICATION This specification describes the performance characteristics of a grounded, with active PFC function, single phase, 120 watts,