Embedded EtherNet/IP Option Card for DriveLogix 5730 Controllers

Transcription

1 Installation Instructions Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the D bus voltage at the +D & D terminals of the Power Terminal lock (D+ & D- in high power drives). The voltage must be zero. TTENTION: HOT surfaces can cause severe burns. Do not touch the heatsink surface during operation of the drive. fter disconnecting power allow time for cooling. TTENTION: This drive contains ESD (Electrostatic Discharge) sensitive parts and assemblies. Static control precautions are required when installing, testing, servicing or repairing this assembly. omponent damage may result if ESD control procedures are not followed. If you are not familiar with static control procedures, reference - publication , Guarding gainst Electrostatic Damage or any other applicable ESD protection handbook. What This Kit ontains Verify that your kit contains the items listed in the following table. If your kit does not contain the correct items, contact your llen-radley sales representative. Quantity: Description 1 Embedded EtherNet/IP Option circuit board 2 Screws 2 Stand-offs Tools That You Need Phillips screwdriver for M3 screws Standard (flat blade) screwdriver Phillips is a registered trademark of Phillips Screw ompany

2 2 Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers What You Need to Do To remove a Embedded EtherNet/IP Option ard from a PowerFlex 700S drive: Step 1: Remove power from the drive Step 2: Open the main drive door Step 3: Remove the control cassette from the drive Step 4: Remove the inside cover from the control cassette Step 5: Remove the old Embedded EtherNet/IP Option ard from the drive To install a new Embedded EtherNet/IP Option ard onto a PowerFlex 700S drive: Step 6: Install the Embedded EtherNet/IP Option ard Step 7: Replace the covers and control cassette Step 8: onfigure EtherNet/IP communications Step 9: Document revision changes To return a replaced Embedded EtherNet/IP Option ard, use packing material from the new Embedded EtherNet/IP Option ard.

3 Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers 3 Step 1: Removing Power from the Drive! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the D bus voltage at the +D & D terminals of the Power Terminal lock. The voltage must be zero. Remove power before making or breaking cable connections. When you remove or insert a cable connector with power applied, an electrical arc may occur. n electrical arc can cause personal injury or property damage by: sending an erroneous signal to your system s field devices, causing unintended machine motion causing an explosion in a hazardous environment Electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance. L1 L2 L3 I O

4 L2 PE D- D+ R2 R1 4 Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers Step 2: Opening Door Over Power Structure and Main ontrol oard Frames 1-4 Locate the slot in the upper left corner. Slide the locking tab up and swing the cover open. Special hinges allow cover to move away from drive and lay on top of adjacent drive (if present). Frame 5 Slide the locking tab up, loosen the right-hand cover screw and remove. Frame 6 Loosen 2 screws at bottom of drive cover. arefully slide bottom cover down & out. Loosen the 2 screws at top of cover and remove. Step 3: Removing the ontrol assette from Drive Proper tightening torque for reassembly is 7 to 10 lb.-in. Task Description Disconnect the cables that connect to the main board Loosen screws on face of cassette Remove the cassette U/T1 V/T2 W/T3 R/L1 =

5 Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers 5 Step 4: Removing the Inside over from the ontrol assette Task Description Loosen screws on face of front cover and remove the cover Proper tightening torque for reassembly is 7 to 10 lb.-in. = Step 5: Removing the Embedded EtherNet/IP Option oard Task Description Remove screws Remove Embedded EtherNet/IP Option oard from the Main ontrol oard Remove standoffs Do not perform this task if you are installing a new Embedded EtherNet/IP Option oard =

6 6 Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers Step 6: Installing the Embedded EtherNet/IP Option oard Task D Description Install and tighten standoffs (7 to 10 lb.-in.) lign connector on Embedded EtherNet/IP Option oard with connector on Main ontrol oard Place Embedded EtherNet/IP Option oard on the Main ontrol oard Install and tighten screws (7 to 10 lb.-in.) D = D Step 7: Replacing the overs and ontrol assette The procedure for replacing the covers and control cassette is the reverse of removing these components. Refer to Step 4: Removing the Inside over from the ontrol assette on page 5, Step 3: Removing the ontrol assette from Drive on page 4 and Step 2: Opening Door Over Power Structure and Main ontrol oard on page 4. Step 8: onfiguring EtherNet/IP ommunication Referring to publication 20D-UM003, User Manual - DriveLogix5730 ontroller, configure the EtherNet/IP port on the option card.

7 Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers 7 Step 9: Documenting Revision hanges Document drive revisions on the Field Installed Options tag. Use the blank line if you are installing the Embedded EtherNet/IP Option oard in a drive that was manufactured without it. FIELD INSTLLED OPTIONS #: Date Firmware Firmware #: Date 20-HIM HIM 28-IO- I/O 20-OMM- OM Module 20_-D1- Internal Dynamic rake TIP: Use packing material from new Embedded EtherNet/IP Option oard to return the replaced Embedded EtherNet/IP Option oard

8 Publication 20D-IN012-EN-P - July 2004 P/N P01 opyright 2004 Rockwell utomation. ll rights reserved. Printed in US.