Tekno 3x1W DWCS - Transparent Screen Model No: TEK US

Transcription

1 Tekno 3x1W DWCS Transparent Screen Model No: TEK US Date: Fixture Type: Project: Specifier/Rep: Certified by C ompliance LM7908 and LM8008 Available for International specifications by adding 'T' at the end of the existing Model # International spec sheets are available upon request Exact Measurements: Metric Model: Installation: Housing: Light Color: Fixture Finish: Diffuser: Fixture Material: Optic: Lamp Type: Number of LEDs: Max Wattage Per Lamp: Total Wattage: Lamp Voltage: Lamp Life: TEK US Surface Fixture for Ceiling,Wall,Ground and Recessed Fixture for Wall and InGround Remodel (NonIC) 205cm / 80 11/16" CAS Required DWCS Anodized Aluminum Transparent PMMA Aluminum Extrusion Alloy UNI 6060 Diffuser Power LED 60 3W x 1W 70W 50,000 hrs at 70% of lamp lumen output with IES LM80. For optimized perfomance follow instruction sheet. Additional Details Pitch: 10 IP Rating: IP65, IP67 (recessed) Width: 6.1cm / 2 3/8" Length: 203cm / 80" Surface mounted or recessed; DMX or DALI dimmable. Requires Housing Box to be ordered separately. LED nonic rated remodel housing is for use in noninsulated areas or where insulation is at least 3 inches from fixture. Height: 3.95cm / 1 9/16" Weight: Breaking 2000g/m / 30.9oz/ft IK04 30 Tycos Dr. Toronto, ON Canada M6B 1V9 PH: / FAX: tech@zaneen.com Page 1 of 2

2 Tekno 3x1W DWCS Transparent Screen Model No: TEK US Date: Fixture Type: Project: Specifier/Rep: Strength: Screws: End Cap: Gasket: Power Supply: Control Gear: Load Resistance: Stainless Steel Polycarbonate Silicone Rubber Constant voltage supply dimmable, parallel connection (Not Included) Sold separately (see components) 300kg / 661.2lbs Walk over Lumen Chart Photometric File Power Color Temperature Nominal Lumen Actual Lumen TEK.304.XX 70W DWCS TEK.304.XX 30K 70W DWCS 3000 K TEK.304.XX 40K 70W DWCS 4000 K TEK.304.XX 55K 70W DWCS 5500 K System Components Tekno Standard Housing Box 205cm [CAS ] 205cm / 80 11/16" Standard Housing Box DMX /010V Control Gear 3 Channels [ECO ] Constant Voltage Dimmable Dali/PWM Interface Control Gear 3 Channels [ECO ] DMX Splitter 1 input / 3 Output channels [ECO ] USB DMX / RDM Interface [ECO ] Power Supply constant voltage 10W [ALI ] Main Voltage Constant V 10W 50/60Hz Power Supply constant voltage 25W [ALI ] Main Voltage Constant V 25W 50/60Hz Power Supply constant voltage 20W [ALI ] Main Voltage Constant V 20W 50/60Hz Available Sizes and / or Lamping Tekno 3x1W DWCS Transparent Screen [TEK US] 53cm / 20 7/8" 15 Power LED, 17W Pitch 10 Tekno 3x1W DWCS Transparent Screen [TEK US] 103cm / 40 9/16" 30 Power LED, 35W Pitch 10 Tekno 3x1W DWCS Transparent Screen [TEK US] 153cm / 60 1/4" 45 Power LED, 52W Pitch 10 Tekno 3x1W DWCS Transparent Screen [TEK US] 203cm / 80" 60 Power LED, 70W Pitch 10 Tekno 3x1W DWCS Transparent Screen [TEK US] 53cm / 20 7/8" 30 Power LED, 35W Pitch 5 Tekno 3x1W DWCS Transparent Screen [TEK US] 103cm / 40 9/16" 60 Power LED, 71W Pitch 5 Tekno 3x1W DWCS Transparent Screen [TEK US] 153cm / 60 1/4" 90 Power LED, 113W Pitch 5 30 Tycos Dr. Toronto, ON Canada M6B 1V9 PH: / FAX: tech@zaneen.com Page 2 of 2

3 Wiring diagrams and electrical connections The new lighting systems, that use light sources in a LED solid state must be connected to the main voltage through electronic devices that maintain the critical parameters of operation constant. With Leds in particular, the current values that pass through the light source must remain constant and if necessary measurements are not taken to keep these parameters constant, the LED will tend to absorb higher currents resulting overheating triggering a vicious mortal cycle of the semiconductor. Because of this physicalelectric phenomenon the systems with LED technology need very sophisticated control devices compared to the traditional sources. The current control can be integrated into the power supply or can be placed between the power supply and the LED system. In this case the Led connection should be done in series with a maximum quantity of 10/12 Led that can be connected In the most evolved systems the control electronic can be split and integrated directly on the PCB together with the Leds; here the connection can be done in parallel with a 24V dc power supply and without any limit of the quantity of Leds that can be connected To facilitate the user in consulting this catalog, in this section there is a list of all the diagrams of connection between control gears, interfaces and power supplies, as well as the combination of the correct power supplies / control gear and lighting systems showing the article codes. Important note: Suggested maximum distance from driver: 30ft (using 18 AWG solid copper wire) Disclaimer: Distances, type of wiring and gauge must be determined by a certified professional to avoid voltage drop problem. Maximum 9m (30 ft) Serial connection Maximum 9m (30 ft) Parallel connection

4 G Parallel connection for constant voltage power supplies (nondimming) codes DIM DIM DIM NO DIM NO DIM NO DIM ALI ALI ALI ALI

5 P DMX/DALI Parallel connection for RGB dimmable systems R G B DMX Interface BUS / DMX interface ECO ECO DMX control gear codes ALI ALI ALI ECO * R G B BUS DMX Interface BUS / ECO BUS DMX / DALI Controller * PC only needed for programming