MiniMac Profile Parts List Description

Transcription

1 MiniMac Profile Parts List Item Description C161 CMOS 16 bit processor 16MHz C66 EEPROM SMD F400, 256Kx16 flash PROM, PSOP HCT 595 serial Octal LATCH,SMD HC 14 HEX inverting Schmitt Trig,SMD LM 358 Dual opamp, SMD M05 5V/0.5A Voltage Stab, SMD L7805 5V/1A Voltage Stab, SMD LM317L, 100mA voltage reg.,smd D/A Converter 8 Chan 8 bit, serial Dual Microstep Driver, PBL 3775N, DIP ULN2803A stepmotor driver, standard ADM 706 AR, supervisory circuit, SMD C176 BiCMOS RS485 Transceiver SMD BC 847B, SMD nf 250V Y2 film capacitor nF, X2, 250V film capacitor uF, 250V, 50-60Hz capacitor w/ 500mm wires uF, 25V, electrolytic, radial uF, 50V, electrolytic, radial pF, 63V, ceramic, SMD nF, 50V, ceramic, SMD nF, 16V, ceramic, SMD uF, 16V, tantalium, SMD uF, 16V, tantalium, SMD OHM RESISTOR, SMD Ohm, resistor, SMD Ohm resistor, SMD, 1206

2 K5 Ohm resistor, SMD, K3 Ohm resistor, SMD, K7 OHM RESISTOR, SMD K OHM RESISTOR, SMD K OHM RESISTOR, SMD OHM RESISTOR, SMD 0.25W OHM RESISTOR, SMD 0.25W OHM RESISTOR, SMD 0.25W OHM RESISTOR, 1%,SMD OHM RESISTOR, 1%,SMD OHM RESISTOR, 1%,SMD K OHM RESISTOR, 1%,SMD K OHM RESISTOR, 1%,SMD M OHM RESISTOR, 1%,SMD R OHM, resistor, 1% 1/10W, SMD R OHM RESISTOR, 1% 1/10W, SMD K2 Ohm resistor, 1% 0.1W, SMD K7 OHM RESISTOR, 1% 1/10W, SMD K7 Ohm resitor, 1% 0.W, SMD K8 Ohm resitor, 1% 0.1W, SMD K2 OHM RESISTOR, 1% 1/10W, SMD K OHM RESISTOR, 1% 1/10W, SMD K OHM RESISTOR, 1% 1/10W, SMD K OHM RESISTOR, 1% 1/10W, SMD M5 Ohm resistor, 1% 0.1, SMD ohm resistor, 1W, SMD BAS32L-115 (1N4148), SMD Diode bridge, PBU V8, diode transil Diode transil, 10V

3 Diode transil, 27V Diode transil, 33V LED 3mm Red Display 3x7 segment, 14mm X-tal 16MHz Spacer isolation for X-tal Noise sup choke, H 2x0.5mH, Step-up 150W; 10,5V/20VA, 24V/48VA Ballast, 150W, 230V, 50Hz, 210/230V, 60Hz Relay, 12V, 16A, single, high current Fuse 2.5AT Fuse 3.15 AT, high I*I*t Fuse holder PCB, plastic support Thermostat, 100 degrees C, open Socket-IC 22 pin, 4 modules,tulip Jumper, 2 pole, 2.54mm spacing XLR female 3-pin chassis, PCB, angle, gold XLR male 3-pin chassis, PCB, angle, gold Header 2 pole 2.54mm PCB Header 4 pole, 2.54mm, PCB, coded Header 6 pole, 2.54mm Header 2 pole 5.0mm molex PCB Header 4 pole 5.0mm molex PCB Header, 40 pole, PCB sil Plug 6 pole PCB sil, angle, coded Header angle 2 pole 5.0mm molex PCB Header angle 6 pole 5.0mm molex PCB Spade plug 6.3mm male, PCB Spade plug 6.3mm male, angle PCB Socket, halogen lamp, GY9.5, 400mm wire

4 AC socket, IEC, chassis mount, w/o fuse holder Fuse holder for P/N Plug, 6 pole, female, angle, yellow, # Plug MTA female angle, wire, 2 pole, natural, # Crimp, term housing, 2 pole, Crimp Term Housing 6 pole, for / Crimp terminal house, 4 pole Cable plug, 2.8mm housing, faston Cable plug, 2.8mm, female, single, faston Cable plug, 6.3 mm female, single, faston, insolated Tact Switch SMD h = 9.5mm Switch 2pol PCB straight, Switch 5pol PCB straight, Micro switch, 5A, 250VAC Stepmotor, standard mini, w/o wire, 22mm shaft Stepmotor, 14PM-M204, wire 1100mm, 12mm shaft Stepmotor, NMB, standard, LC, wire Stepmotor micro HP LN, w/o wire Fan 12V DC Brushless 1.6" Fan 12V DC Brushless 75 x 75mm Centrifugal, sleeve bearing Microphone, elec. con., SKP Starter 150W serial, NI 400 LE M2.5x5 taptite, Phillips, cs M3x4 screw, Phillips, ph, black M3x5 taptite, Phillips, ph, black M3x10 screw, Phillips, ph M3x12 screw, Phillips, ph, black M3x16 screw, Phillips, ph, black M3x16 screw, Phillips, cs, black M3x6 taptite, Torx, ph, black

5 M3x8 taptite, Torx, ph, black M3x6 screw, Torx, ph, black M3x6 screw, Torx, cs, black M3 hex nut, black M3 hex lock nut M3x10 stand off, m/f, black M3x23.5 stand off, f/f, black M3x40 stand off, m/f, black M3x30 stand off, m/f M3 Washer M3 lock washer, black M4x6 screw, Phillips, black M4x16 screw, Phillips, ph, black M4x30 screw, Phillips, ph, black M4x20 screw, Phillips, cs, black M4x10 taptite, Torx, ph, black, Paint cut M4x6 taptite, Torx, ph, black, spec M4x12 hex cap screw, black M4x5 set screw M4 hex nut, black M4 blind rivet nut, cs M4 blind rivet nut M4 Washer, black M4 lock washer, black M5x12 hex cap screw, taptite, black M6x10 screw, Allen, black M6x16 screw, Allen, black M6x40 screw, Allen, black M6 hex nut M6 hex lock nut, PA-insert

6 M6 blind rivet nut M6x55 stand off, f/f, Zn M6 lock washer M8x16 screw, Allen M8x16 screw, Torx M8x13 lifting eye bolt, black M8 hex nut, stainless M8 hex weld nut x38 self-tap, ph, black x13 Self-tap, Torx, black x6.5 Plastite, ph, black x8 eco-syn, ph, black x8 eco-syn, ph, black x12 Plastite, ph, black x10 eco-syn, ph, black x6 eco-syn, cs x 7.5 mm Rivet Alu mm x 8 Rivet Black x 9 mm Rivet Alu x9,5 Pop Rivet UH St.St mm x 11,5 Rivet St. St Cylinder Pin 3 x 28 mm Locking ring snap on 30mm x 1.5mm Locking ring snap on 3,2mm x 0,6mm /4 turn fastener, screw w. spring, black /4 turn 6mm receptacle /4 turn fastener, retainer, 6mm /4 turn fastener, wingbolt /4 turn fastener, retainer /4 turn fastener pedestal

7 Cap for fastener pedestal Spacer brass l=6, d=3.3 D= Spacer brass l=9, d=3.3 D= Spacer Snap-PCB / selftap, h = 9.4mm Shim Washer d1=32, d2=44 mm, s=0,5, BN Wire, yellow/green, 1x0.75#, 11cm Wire, yellow/green, 1x0.75#, 25cm Wire, brown, 1x0.75#, 13cm Wire, brown, 1x0.75#, 32cm Wire, brown, 1x0.75#, 21cm Wire, brown, 1x0.75#, 13cm Wire, blue, 1x0.75#, 13cm Wire, blue, 1x0.75#, 21cm Wire, red, 1x0.75#, 13cm Wire, red, 1x0.75#, 32cm Wire, black, 1x0.75#, 13cm Wire, black, 1x0.75#, 13cm Wire, grey, 1x0.75#, 13cm Wire, purple, 1x0.75#, 14cm Wire, orange, 1x0.75#, 16cm Wire, blue, 1x0.75#UL, 132cm, SIFF Wire, blue, 1x0.75#UL, 28cm, SIFF Wire, black, 1x0.75#UL, 120cm, SIFF Mains cable I.E.C. 3pin, 3 m Wire for stepmotor, 270mm, 4 wire, NMB Wire for stepmotor, 53cm, 4 wire, NMB Wire for stepmotor, 100cm, 4 wire, NMB Wire for stepmotor, 110cm, 4 wire, NMB Wire for stepmotor, 100cm, 6 wire, NMB, LC Wireset 6x0.14#,2 fem. plugs, black, 1000mm

8 Wireset, 6x0.3#, 2 fem. plugs, black, 365mm XLR cable 5m black 3P male-3p female Strap, black, high temp, 2.5x98mm Strap, auto, high-temp., 2.5x103mm /9/12mm Rubber nibble pla Rubber nibble DA 60/90/ Rubber List, U-Profile Sleeve flexible,hose 5mm, black Silicon/glas sleeve d=4mm,black Silicon/glas sleeve d=9mm,black Sleeve tube flexible 10mm, black Plastic toothwheel, S3M Timing pulley, S3M, Z=16, l=17mm S3M,Z=32,Timing pulley, l=15mm Timing belt, supertorque MBL, l= Timing Belt S3M Pulley for belt, MiniMAC Pulley f. belt bearing MiniMAC Belt, VITON, d=75.87mm x 2.62mm Adaptor for colorwheel, MAC 500, degreased Adaptor w. 5mm hole, degreased Bushing for MiniMAC bearings Closed ball bearing, D=16, d=5,lc Ball bearing 1, D=27, d=20, b= Ball bearing, D=42, d=30, b= Bushing for belt adjust., MiniMAC Shaft, belt wheel, MiniMAC Shaft, Pan/Tilt, MiniMAC Shaft for belt RG, MiniMAC Plastic gobo bearing housing

9 Bearingadapt, belt wheel, MiniMAC Bearingadapt, Pan/Tilt, MiniMAC Bearingadaptor belt wheel MiniMAC Gobowheel, MiniMAC Light shield, MiniMAC Adaptor MiniMAC focus lens Alu-nut for MiniMAC focus lens Goboguide, rotating MAC250, HT-painted Spring for PAL 1200 frost damper Tension spring, D=10, d=1x Circular spring, d=18x Spring ø56x1.4 Focus, MAC250, bent Gobo Spring, 4 bends, MAC Spring for pan switch, MiniMac Spring for MAC 250-size gobos, 2 bends Spacer, d=4, ø6x Spacerpl. for cam lock system Mechanical stop for Gobo wheel, MiniMAC Pl., Mec. Stop, Pan, MiniMAC Mec. Stop, Plastic w. spring Rubber foot 25x15mm. Black Counterweight, head, MiniMAC Counterweight 1,Pan, MiniMAC Counterweight 2,Pan, MiniMAC Ø8,0 14x4mm Silicone ring Bracket for shell, MiniMAC Plate for counterweight / Airguide for lamp, MiniMAC Plate for lampadjust., MiniMAC Plate for lampsocket, MiniMAC Plate for Belt adjust, MiniMAC

10 Plate for base bearing MiniMAC Plate for capacitor, MiniMAC Plate for ballast, MiniMAC Plate for handle, MiniMAC Lamp lid, Head minimac Plast shell Head Top, Black, MiniMac Bottom shell, head, black, type II (ext. screw) Plast shell Arm outer, Black, MiniMac Plast shell Arm inner, MiniMac Plast shell Base top, Black, MiniMac Plast shell Base bottom, MiniMac Plast shell Base Ventilation, MiniMac Rubber cabinet list long, MinMac Rubber cabinet list short front, MinMac Rubber cabinet list short rear, MinMac Rubber ring for objective, Minimac Plate 1 for Yoke, MiniMAC Plate 2 for Yoke, MiniMAC Plate 3 for Yoke, MiniMAC Color module plate, MiniMAC Lens module plate, MiniMAC Refl. module plate, MiniMAC Chassis module plate, MiniMAC Plate for Pan motor, MiniMAC Chassisplate, Base, MiniMAC Base support plate, MiniMAC PCB module plate, MiniMAC Bracket for pan bushing, MiniMAC Bracket for tilt bushing, MiniMAC MiniMAC Profile label

11 Keyboard overlay, MiniMAC Adhesive aluminium foil, 100 x 100 x 0.05 mm Label, PCB connections, MiniMAC Wash/Profil Label Instructions 1/4 turn Lamp adjustment label, MiniMAC Label Safetywire/Eye Bolt Label Warning MiniMAC Clamps Label Front Cardboard box MiniMAC Profile MiniMAC Polystyren packing PLAST BAG 180x PLAST BAG,600x850mm,Spandepose Plast bag, 60x80, fuse Plast bag, 60x80, f. fuse, EU V Shrinkfoil, 19my, B=1100mm Rubberband 250x15 mm User manual, MiniMAC Loctite gr Silicon glue clear, low temp. ( øc) Silicon glue, hightemp. (250 C), red Ellipsodial reflector D= Heat filter, WBHM3, 1.1mm, MAC 250 shape Lens, Pl/Cx, D=50, coated Lens, D=50, meniscus, coated Lens, D=50, meniscus, coated Sunburst Magenta, size 250, glass gobo Special Glass gobo MAC250 Fibroid size R 22.5 mm Open gobo, Ø22,5/17 HT-painted Gobo alu, Decentered beam, Size R, MAC250, HT-painted Gobo alu, Radial Dashes, Size R, MAC250, HT-painted

12 Gobo alu, Stardust 2, MiniMac, HT-painted Gobo alu, Atomic 2, Size R, MAC250, HT-painted Gobo alu, Highways 2, Size R, MAC250, HT-painted Yellow 603, "trap (R28,5;R51,4)x21,1" Blue 104, "trap (R28,5;R51,4)x21,1" Pink 312, MAC 250 shape Red 301M, "trap (R28,5;R51,4)x21,1" Magenta 507, "trap (R28,5;R51,4)x21,1" Blue 101, "trap (R28,5;R51,4)x21,1" Orange 306M, "trap (R28,5;R51,4)x21,1" Green 208, "trap (R28,5;R51,4)x21,1" Dichr. CTC K, "trap (R28,5;R51,4)x21,1" Blue 108 IAD, "trap (R28,5;R51,4)x21,1" Purple 502, MAC 250 shape Green 206iad, MAC 250 shape Lens module, MiniMAC Wireset, MiniMAC Rot. Gobo module, MiniMAC Profile Color module Profile, MiniMAC MiniMAC manual/fuse packing PCB/sw module, MiniMAC Profile PCB MiniMAC Display/Keyboard, Tested PCB MiniMAC, Main Board tested PCB Voltage/Feq. select, Asmb Wire for micro-switches, MiniMac Wire for Display, 180mm Wireset for relay,minimac Wireset mains in,minimac Wireset Power PCB, Minimac Wireset for step-up,minimac

13 Wireset for ballast,minimac Wire for head fan, MiniMAC High-flex wireset, complete, MiniMac Profile Fan 1.6` with plug 200mm wire Fan 12V DC Brushless,W.plug 220mm #20uF 250V Capacitor prep w plugs Wire stepmotor 4 wire 530mm ;TILT; Wire stepmotor 4 wire 270mm ;PAN; Wire stepmotor 4 wire 1100mm ;GOBO; Wire stepmotor 4 wire 1000mm ;ROGO; Wire stepmotor 6 wire 1000mm ;SHUT; Wire stepmotor 4 wire 1100mm ;COL; Sunburst etched in Magenta 507 1/4 disk Ø Shutter MiniMac, glued Color Wheel 1 rev. 2, MiniMAC Plastshell inner yoke, Black, glued w. ballastplate Rotating GoboWheel, MiniMAC Counterweight assembl. MiniMac Aperture ring, MiniMac, HT-paint HT paint Aluspacer MiniMac Omega bracket, new w. 1/4-turn HTI150M Lamp Metal Halide (Martin) 2000 hours Martin labels sheet, Martin labels 7 pcs.