CAUTION CAUTION CAUTION HIGH VOLTAGE PRESENT

Transcription

1 INSTALLATION INSTRUCTIONS OF THE POWER ANALYZER CAUTION CAUTION CAUTION HIGH VOLTAGE PRESENT READ THROUGH THE INSTRUCTIONS CAREFULLY AND ALWAYS OBIDE BY LOCAL ELECTRICAL CODE. RXMS CAN NOT BE HELD RESPONSIBLE FOR IMPROPER INSTALLATION AND/OR INJURY. ALWAYS POWER DOWN ALL ELECTRICAL CIRCUITS BEFORE INSTALLATION!

2 Quick Reference Guide for the EPA1000 Please refer to the Installation Instructions for full details on how to install the EPA1000. Follow these simple steps: 1. Unpack the EPA Power down YOUR system and turn off power at main circuit breaker 3. Power up the EPA Connect the Voltage Leads 5. Connect the Current Probes 6. Connect the Temp/Hum Probe 7. Power up YOUR system and turn it on 8. Fill out Site Info and Detailed Site Log 9. Uninstall the EPA1000 and ship back DANGER HIGH VOLTAGE! The above steps require system-trained personnel only or local qualified personnel (i.e. a local electrician)

3 1. Unpack The EPA1000 a. Check the packing list to make sure all of the requested equipment was received. b. Position near the connection point to be tested (be sure the EPA1000 is positioned in an area where it will not be dropped or interfered with). EPA Power down YOUR system and turn off the power at the main circuit breaker. Top of EPA Power Up The EPA1000 a. Plug in the supplied power cord into a 120V, 50/60 Hz outlet, or use the breakout style power cord of the RxMS A/C adapter (if present). (If an extension cord is needed, it must be a 3-prong, grounded extension cord). b. Plug the female end into the power supply of the EPA1000. A/C Adapter

4 Run Voltage Leads Connect Banana Leads 4. Connect The Voltage Leads For Hardwired Setup: a. Connect the L1, L2 and L3 voltage leads (alligator clip or strip) to the main circuit breaker. Connect the N lead to the Neutral bar (if present), and the G lead to the main chassis or the Ground bar. b. Connect the other end of the voltage leads (right-angle banana plug) into their corresponding color-coded ports on the front panel of the EPA1000. For A/C Adapter Setup: a. If you are using an A/C adapter provided by RxMS, unplug your equipment from the wall or from the Power Conditioner. b. Plug your equipment into the female end of the A/C adapter, and plug the male end of the A/C adapter into the receptacle. c. Plug the end of the voltage leads (rightangle banana plug) into their corresponding color-coded ports on the front panel of the EPA1000. A/C Adapter

5 Connect Current Probes to Panel A/C Adapter 5. Connect The Current Probes a. Please note that connecting the current probes is a crucial part of the data gathering process. Please make sure you connect them to ensure that all supporting data is gathered. b. Clamp the current probes around L1, L2, L3, N and G (or all applicable phases) and make sure that there is only one wire clamped in each current probe. c. If you are using an A/C adapter provided by RxMS, please refer to the photos on the left to ensure that you are clamping the current probes to the correct location. d. Make sure that each current clamp is connected to the correct wire and that the direction of the arrow on the clamp is pointing toward your load/system. e. Plug the other end of the current probes into their corresponding ports on the front panel of the EPA1000 (to the right of the color-coded voltage ports). Connect Current Probes

6 Rx Temp/Hum Probe Located on Front Panel of EPA Connect The Temp/Hum Probe a. Hang the Temp/Hum probe at a minimum height of 6 feet (if possible), and make sure it is not positioned near a door, window, or ventilation unit and plug into the Temp/Hum port on the front panel of the EPA1000. Correct Reading 7. Power up YOUR system and turn it on a. Within five to ten seconds, the LCD screen on the EPA1000 will show real-time voltage and temp/hum readings (please note that the LCD screen is configured only to display phase-to-phase voltages). Wrong Reading

7 Site Information Sheet 8. Fill Out Site Info And Detailed Site Log a. Please make sure you fully complete the RxMS Site Information sheet with the detailed information of the site and equipment being monitored. b. Make sure you leave the Detailed Site Log that was provided with the EPA1000 with your customer. They should use the Detailed Site Log to record any system events that will help RxMS correlate all gathered data to any errors you may be having with your system. c. Please leave the EPA1000 in place for five to seven days of monitoring. Call RxMS at once you have installed the EPA1000. Detailed Site Log FedEx Return Label 9. Uninstall The EPA1000 And Ship Back a. Power down your system and the main power. b. Unplug the power cord from the EPA1000. c. Disconnect all probes from the EPA1000. d. Pack all equipment in provided shipping case. e. Attach the enclosed FedEx AirBill and ship equipment back to RxMS.