StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex. Installation Guide For HBA Models SG-XPCIE2FC- EB4-Z and SG-PCIE2FC-EB4-Z

Transcription

1 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide For HBA Models SG-XPCIE2FC- EB4-Z and SG-PCIE2FC-EB4-Z Part No.: E July 2013

2 Copyright 2007, 2013, Oracle and/or its affiliates. All rights reserved. This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform, publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is prohibited. The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing. If this is software or related software documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, the following notice is applicable: U.S. GOVERNMENT END USERS. Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government. This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this software or hardware in dangerous applications. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered trademark of The Open Group. This software or hardware and documentation may provide access to or information on content, products, and services from third parties. Oracle Corporation and its affiliates are not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content, products, or services. Copyright 2007, 2013, Oracle et/ou ses affiliés. Tous droits réservés. Ce logiciel et la documentation qui l accompagne sont protégés par les lois sur la propriété intellectuelle. Ils sont concédés sous licence et soumis à des restrictions d utilisation et de divulgation. Sauf disposition de votre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire, traduire, diffuser, modifier, breveter, transmettre, distribuer, exposer, exécuter, publier ou afficher le logiciel, même partiellement, sous quelque forme et par quelque procédé que ce soit. Par ailleurs, il est interdit de procéder à toute ingénierie inverse du logiciel, de le désassembler ou de le décompiler, excepté à des fins d interopérabilité avec des logiciels tiers ou tel que prescrit par la loi. Les informations fournies dans ce document sont susceptibles de modification sans préavis. Par ailleurs, Oracle Corporation ne garantit pas qu elles soient exemptes d erreurs et vous invite, le cas échéant, à lui en faire part par écrit. Si ce logiciel, ou la documentation qui l accompagne, est concédé sous licence au Gouvernement des Etats-Unis, ou à toute entité qui délivre la licence de ce logiciel ou l utilise pour le compte du Gouvernement des Etats-Unis, la notice suivante s applique : U.S. GOVERNMENT END USERS. Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government. Ce logiciel ou matériel a été développé pour un usage général dans le cadre d applications de gestion des informations. Ce logiciel ou matériel n est pas conçu ni n est destiné à être utilisé dans des applications à risque, notamment dans des applications pouvant causer des dommages corporels. Si vous utilisez ce logiciel ou matériel dans le cadre d applications dangereuses, il est de votre responsabilité de prendre toutes les mesures de secours, de sauvegarde, de redondance et autres mesures nécessaires à son utilisation dans des conditions optimales de sécurité. Oracle Corporation et ses affiliés déclinent toute responsabilité quant aux dommages causés par l utilisation de ce logiciel ou matériel pour ce type d applications. Oracle et Java sont des marques déposées d Oracle Corporation et/ou de ses affiliés.tout autre nom mentionné peut correspondre à des marques appartenant à d autres propriétaires qu Oracle. Intel et Intel Xeon sont des marques ou des marques déposées d Intel Corporation. Toutes les marques SPARC sont utilisées sous licence et sont des marques ou des marques déposées de SPARC International, Inc. AMD, Opteron, le logo AMD et le logo AMD Opteron sont des marques ou des marques déposées d Advanced Micro Devices. UNIX est une marque déposée d The Open Group. Ce logiciel ou matériel et la documentation qui l accompagne peuvent fournir des informations ou des liens donnant accès à des contenus, des produits et des services émanant de tiers. Oracle Corporation et ses affiliés déclinent toute responsabilité ou garantie expresse quant aux contenus, produits ou services émanant de tiers. En aucun cas, Oracle Corporation et ses affiliés ne sauraient être tenus pour responsables des pertes subies, des coûts occasionnés ou des dommages causés par l accès à des contenus, produits ou services tiers, ou à leur utilisation. Please Recycle

3 Contents Preface v 1. HBA Overview 1 HBA Features and Specifications 1 System Interoperability 2 Host Platform Support 3 Storage System Support 3 Fibre Channel Switch Support 3 Operating System Requirements 4 2. Hardware Installation and Removal 5 Observing ESD and Handling Precautions 5 Installing the Hardware 6 To Install the HBA 6 To Connect the Optical Cable 7 To Apply Power 9 Testing the Installation (Oracle Solaris) 11 To Verify Proper Installation (Oracle Solaris) 11 To Verify Attached Storage (Oracle Solaris) 11 Configuring the HBA for Hot-Plug Operation 12 iii

4 Configuring the HBA for Hot-Plug Operation 12 Removing the Hardware 12 To Prepare the HBA for Removal Using the HBA Attention Button 13 To Prepare the HBA for Hot-Plug Removal (for Oracle Solaris) 13 To Remove the HBA Hardware HBA Software Installation 15 Driver Software for the Oracle Solaris OS 15 Oracle Solaris Diagnostic Support 15 Installing Software for the Red Hat and SUSE Linux OSs 16 To Install the HBA Software for Linux OS 16 Installing Software for Windows Server To Install the Software for Windows Server Configuration and Diagnostic Utilities Release Notes 19 Oracle Solaris 10 for x64/x86 Operating Systems 19 Red Hat Enterprise Linux 4 and SUSE Linux Enterprise Server 9 Systems 19 Windows Server 2003 Operating System 20 iv StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

5 Preface This guide describes how to install and remove the StorageTek 4 Gb FC Dual Port ExpressModule host bus adapter (HBA). It also explains how to verify the driver version and install any necessary patches. This document is written for technicians, system administrators, application service providers (ASPs), and users who have advanced experience troubleshooting and replacing hardware. This preface contains the following topics: Related Documentation on page vi Feedback on page vi Support and Accessibility on page vi v

6 Related Documentation To view, print, or purchase a broad selection of Oracle documentation, including localized versions, go to: To access HBA and Converged Network Adapter documentation, go to: Feedback Provide feedback on this documentation at: Support and Accessibility Description Access electronic support through My Oracle Support Links For hearing impaired: Learn about Oracle s commitment to accessibility html vi StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

7 CHAPTER 1 HBA Overview This chapter provides a basic overview of the StorageTek 4 Gb FC Dual Port ExpressModule Host Bus Adapter (HBA). This chapter also describes the various operating systems, host platforms, storage, and infrastructure configurations that support the HBA. This chapter contains the following topics: HBA Features and Specifications on page 1 System Interoperability on page 2 Operating System Requirements on page 4 HBA Features and Specifications The StorageTek 4 Gb FC Dual Port ExpressModule HBA (SG-XPCIE2FC-EB4-Z) consists of a single wide, ExpressModule bus expansion board that interfaces a 4- lane (8-lane physical) PCI-Express bus to a Fibre Channel (FC) optical media bus. The HBA can act as either an initiator or a target. The board supports two independent FC buses operating at 4.25 Gbits/sec. It is also backward compatible with Gbit/sec and Gbit/sec devices. See TABLE 1-1 for a list of the HBA features. TABLE 1-1 Feature HBA Features and Specifications Description PCI connector PCI signaling environment PCI transfer rate (maximum) Number of FC buses x8 PCI Express x4 (4 active lanes) PCI Express Generation One (2.5 Gbits/sec) x4 Two 1

8 TABLE 1-1 Feature HBA Features and Specifications (Continued) Description Number of devices supported FC bus type (external) FC transfer rate RAM BIOS ROM NVRAM External connectors Maximum FC cable length LED indicators Form Factor 126 devices per FC loop; 510 devices in Fabric mode Fiber optic media, short-wave, multi-mode fiber (400-M5- SN-S) 400 MBps per port maximum, half duplex 800 MBps per port maximum, full-duplex 1.5 MB, parity protected, per port One 4-MB flash ROM, field-programmable One 2-KB EEPROM, field-programmable Two Small-Form Factor (SFF) multimode optic with LCstyle connectors 1 Gbps:500 meters using 50/125 mm core fiber 300 meters using 62.5/125 mm core fiber 2 Gbps:300 meters using 50/125 mm core fiber 150 meters using 62.5/125 mm core fiber 4 Gbps:150 meters using 50/125 mm core fiber 70 meters using 62.5/125 mm core fiber Two LEDs per channel (yellow and green) on the front panel as status indicators Power LED, Attention LED, and a push button on the front panel to support hot-swap functionality PCI ExpressModule, single wide System Interoperability This section provides information about selected platforms, storage systems, and switches that are compatible with the heterogeneous FC network design of the HBA. This section contains the following topics: Host Platform Support on page 3 Storage System Support on page 3 Fibre Channel Switch Support on page 3 2 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

9 Host Platform Support The HBA is supported by the platforms and operating systems (OSs) listed in TABLE 1-2. TABLE 1-2 Platform Platform and Operating System Support Supported OSs Sun Blade 8000 Series Modular Systems Oracle Solaris, Linux, and Windows The system must have an available ExpressModule slot in which you can install the HBA. Storage System Support The HBA supports the following storage systems: StorEdge 3510 and 3511 FC Arrays StorEdge 6020 and 6120 Arrays StorEdge 6130 Array StorageTek 6140 Array StorageTek 6540 Array StorageTek FlexLine 380 Storage System StorEdge 6320 system StorEdge L25 and L100 tape libraries with Fibre Channel / LVD Internal Bridge StorEdge C4 tape library with LVD SCSI to Fibre Channel Card StorEdge L500 tape library StorEdge L180, L700 tape libraries StorEdge L5500, L8500 tape libraries Fibre Channel Switch Support The HBA is supported with the following FC switches: 2 Gb QLogic SANbox 5200 switch 4 Gb QLogic SANbox 5600 and 5602 Stackable FC switches 2 Gb Brocade SilkWorm 3200 and 3800 switches 2 Gb Brocade SilkWorm 3250 and 3850 switches Chapter 1 HBA Overview 3

10 2 Gb Brocade SilkWorm 3900 switch 2 Gb Brocade SilkWorm and Core Fabric switches 4 Gb Brocade SilkWorm 4100 switch 4 Gb Brocade SilkWorm and 200E 2 Gb McDATA Sphereon 4300 switch 2 Gb McDATA Sphereon 4500 switch 4 Gb McDATA Sphereon 4400 and 4700 switches Operating System Requirements The HBA requires the operating system (OS) levels, at minimum, listed in TABLE 1-3. TABLE 1-3 Supported Operating System Versions (Minimum) Operating Systems Linux Supported Versions (Minimum) Red Hat Enterprise Linux (RHEL) 4 U3 x32, x64 Red Hat Enterprise Linux (RHEL) 4 U4 x32, x64 SUSE Linux Enterprise Server (SLES) 9 SP3 x64 Oracle Solaris (x64) Oracle Solaris 10 Update 3, 2, or 1 and latest patches and You can obtain the latest patches at: Oracle Solaris 10, latest patches , , and plus packages SUNWemlxs and SUNWemlxu Oracle Solaris (SPARC) Oracle Solaris 10 Update 3, 2, or 1 and latest patches and Oracle Solaris 10 and latest patches , , and plus packages SUNWemlxs and SUNWemlxu Windows Windows Server 2003 Enterprise Edition x64 Windows Server 2003 Standard Edition x64 Windows Server 2003 Enterprise Edition x86 w/sp1 Windows Server 2003 Standard Edition x86 w/sp1 4 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

11 CHAPTER 2 Hardware Installation and Removal This chapter describes the tasks required to install and remove the HBA. Refer to your system installation or service manual for detailed instructions. This chapter contains the following topics: Observing ESD and Handling Precautions on page 5 Installing the Hardware on page 6 Testing the Installation (Oracle Solaris) on page 11 Configuring the HBA for Hot-Plug Operation on page 12 Removing the Hardware on page 12 Observing ESD and Handling Precautions Caution Damage to the HBA can occur as the result of careless handling or electrostatic discharge (ESD). Always handle the HBA with care to avoid damage to electrostatic sensitive components. To minimize the possibility of ESD-related damage, Oracle strongly recommends using both a workstation antistatic mat and an ESD wrist strap. You can get an ESD wrist strap from any reputable electronics store or from Oracle as part number # Observe the following precautions to avoid ESD-related problems: Leave the HBA in its antistatic bag until you are ready to install it in the system. Always use a properly fitted and grounded wrist strap or other suitable ESD protection when handling the HBA and observe proper ESD grounding techniques. 5

12 Hold the HBA by the edge of the PCB, not the connectors. Place the HBA on a properly grounded antistatic work surface pad when it is out of its protective antistatic bag. Installing the Hardware The hardware installation process involves the following general steps: To Install the HBA on page 6 To Connect the Optical Cable on page 7 To Apply Power on page 9 To Install the HBA 1. Attach an antistatic strap (refer to Observing ESD and Handling Precautions on page 5). 2. Refer to your system installation or service manual to determine an appropriate ExpressModule slot in which to install the HBA. 3. Press down the plastic tab to release the ExpressModule latch and pull the lever out until it is nearly perpendicular with the ExpressModule front panel. 6 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

13 FIGURE 2-1 The HBA With Its Latch Pulled Out 4. Insert the HBA into its slot, being careful that the tooth on the bottom of the lever does not come in contact with the chassis sheet metal during insertion. 5. When the HBA is inserted nearly all the way into its slot, push the lever back into its fully closed position, allowing the lever tooth to insert the HBA fully into place. To Connect the Optical Cable 1. Use multimode fiber-optic cable, intended for short-wave lasers, that adheres to the specifications in the following table. Note The HBA does not allow normal data transmission on an optical link unless it is connected to another similar or compatible Fibre Channel (FC) product (that is, multimode to multimode). Chapter 2 Hardware Installation and Removal 7

14 Fiber-Optic Cable Maximum Length Minimum Length Connector 62.5/125 mm (multimode) 50/125 mm (multimode) 300 meters at Gbps 150 meters at Gbps 70 meters at 4.25 Gbps 500 meters at Gbps 300 meters at Gbps 150 meters at 4.25 Gbps 2 meters LC 2 meters LC 2. Connect the fiber-optic cable to an LC connector on the HBA. FIGURE 2-2 Two Optical Cables Connecting to the HBA 3. Connect the other end of the fiber-optic cable to the FC device. After the optical cable is connected to the HBA, you are ready to apply power to the system. If power is already applied to the system, proceed to Configuring the HBA for Hot-Plug Operation on page StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

15 To Apply Power 1. Verify that the HBA is securely installed in the system. 2. Verify that the correct optical cable is attached. 3. Refer to your system installation or service manual to determine how to power up the system blade. 4. Observe the light-emitting diodes (LEDs) status for the power-on self test (POST) results as shown in the following table. The following table summarizes LED indicator combinations. Refer to FIGURE 2-3 to determine the location of the LEDs. Each port has a corresponding set of LEDs that provide a visual indication of the operating state. Green LED Yellow LED State On 1 fast blink 1-Gb link rate - Normal operating state, link up On 2 fast blinks 2-Gb link rate - Normal operating state, link up On 3 fast blinks 4-Gb link rate - Normal operating state, link up Off Off Wake-up failure (failed board) Off On POST failure (failed board) Off Slow blink Wake-up failure monitor Off Fast blink Failure in POST Off Flashing POST processing in progress On Off Failure while functioning On On Failure while functioning Slow blink Off Normal - link down Slow blink On Not defined Slow blink Slow blink Off-line for download Slow blink Fast blink Restricted off-line mode (waiting for restart) Slow blink Flashing Restricted off-line mode, test active Chapter 2 Hardware Installation and Removal 9

16 FIGURE 2-3 LEDs and the Attention Button 10 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

17 Testing the Installation (Oracle Solaris) This section describes how to confirm that the HBA is installed and functioning. The section contains the following topics: To Verify Proper Installation (Oracle Solaris) on page 11 To Verify Attached Storage (Oracle Solaris) on page 11 To Verify Proper Installation (Oracle Solaris) 1. Use the cfgadm command to verify proper HBA installation: If the HBA is properly installed and connected, you will see output similar to the following: cfgadm Ap_Id Type Receptacle Occupant Condition c3 fc connected configured ok c4 fc connected configured ok pcie5 fibre/hp connected configured ok 2. If an HBA adapter is shown as unconfigured or disconnected, use the cfgadm -c configure command to configure the adapter. To Verify Attached Storage (Oracle Solaris) 1. Use the cfgadm -al command to verify attached storage: If the HBA is properly installed and storage is connected properly, you will see output similar to that shown below. In this example, one port of an HBA adapter is connected through a fabric switch to two ports of a disk array. Ap_Id Type Receptacle Occupant Condition c3 fc-fabric connected configured unknown c3::200600a0b816005e disk connected configured unknown c3::200700a0b816005e disk connected configured unknown c4 fc connected unconfigured unknown pcie5 fibre/hp connected configured ok 2. If an adapter is shown as unconfigured, use the cfgadm -c configure command to configure it. Chapter 2 Hardware Installation and Removal 11

18 Configuring the HBA for Hot-Plug Operation Follow the procedure in this section to configure the HBA for hot-plug operation. Configuring the HBA for Hot-Plug Operation 1. Locate the green Power LED indicator near the bottom of the HBA front panel (see FIGURE 2-3). Power LED indicator status is as follows: LED State Meaning Removal Status Dark Power is not applied to the HBA. Removal is permitted, or the HBA needs to be configured. Flashing Hot-plug operation is in process. Removal of the HBA is not permitted. Solid green The HBA is properly configured. Removal is not permitted. 2. If the green Power indicator is not illuminated, briefly press the Attention button near the bottom of the HBA front panel. The green power LED will blink for approximately five seconds and then remain on, indicating that the HBA has been properly configured. To cancel the operation, press the button again before it stops blinking. Removing the Hardware The following instructions describe the tasks required to remove the HBA. Refer to your system installation or service manual for detailed HBA adapter removal instructions. The hardware removal process involves the following general steps: 1. Either halting the operating system and removing power from the server blade, or preparing the HBA for hot-plug removal with one of the following: The HBA Attention button 12 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

19 The Oracle Solaris OS 2. Removing the HBA hardware To Prepare the HBA for Removal Using the HBA Attention Button 1. Press and release the Attention button near the bottom of the HBA front panel. The green Attention LED near the button should blink for approximately five seconds, indicating that the HBA is being prepared for removal. If you want to abort the operation, press the button again before the LED stops blinking. 2. After the Attention LED goes dark, remove the HBA. To Prepare the HBA for Hot-Plug Removal (for Oracle Solaris) If you want to remove the HBA without first halting the operating system and removing power from the associated server blade, you may first prepare it for removal as follows: 1. Use the cfgadm command to identify the HBA to be removed. Ap_Id Type Receptacle Occupant Condition pcie5 fibre/hp connected configured ok pcie6 fibre/hp connected configured ok 2. Use the cfgadm -c unconfigure command to unconfigure the attachment point ID (Ap_Id) for the HBA. 3. Use the cfgadm -c disconnect command to prepare the HBA for removal. A flashing Power indicator LED indicates that the HBA is being prepared for removal. A dark Power indicator LED indicates that the HBA is ready to be removed. Chapter 2 Hardware Installation and Removal 13

20 To Remove the HBA Hardware Press the HBA latch to disengage the HBA, and then pull forward and down to eject it. You can now remove the HBA. 14 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

21 CHAPTER 3 HBA Software Installation After you have completed the hardware installation and powered on the computer, follow the instructions listed in this chapter for your operating system to install the HBA driver and any other utilities required for your installation. This chapter contains the following topics: Driver Software for the Oracle Solaris OS on page 15 Installing Software for the Red Hat and SUSE Linux OSs on page 16 Installing Software for Windows Server 2003 on page 17 Configuration and Diagnostic Utilities on page 18 Driver Software for the Oracle Solaris OS The HBA driver for the Oracle Solaris OS is included with the Oracle Solaris 10 Update 1 release. No additional patches or packages are required to support the HBA on minimum supported versions of Oracle Solaris for x64/x86 systems. Oracle Solaris Diagnostic Support Diagnostic support for the HBA is included in the Oracle VTS software beginning with version 6.3. Diagnostic support for the universal HBA is included in the Oracle VTS software. The Oracle VTS software is available for download at: For information about the Oracle VTS software, see the Oracle VTS documentation at: 15

22 The emlxtest utility, which is part of the Oracle VTS software, supports the following functions: Connectivity verification Firmware version and checksum test Selftest Loopback tests External Internal, single-bit Internal, 10-bit Mailbox Installing Software for the Red Hat and SUSE Linux OSs No updates are required to support the HBA on minimum supported versions of Linux. For diagnostic support, you might need to rebuild the Linux driver. Before rebuilding the drivers for Linux, you must have the required Linux operating system (OS) installed on your hard disk. The driver and utilities are available for download at the Emulex support site for Oracle. To Install the HBA Software for Linux OS The driver and management utilities are available for download at the Emulex support site for Oracle. 1. Go to the Emulex support site for Oracle at: 2. Locate the StorageTek section, and click the model number (SG-XPCIE2FC-EB4- Z) for the HBA you want to install. 3. Locate the Linux Driver section, and click the Download link to copy the driver files to a local file system. 4. Click the Download link to copy the management utilities to a local file system. 16 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

23 5. Click the Manual link to copy the PDF manual and follow the installation and configuration procedures. 6. Click the PDF Manual icon to download installation, configuration, and troubleshooting information. 7. Install the driver for Linux as described in the Emulex driver and utilities user guide. 8. Install the management utilities as described in the Emulex driver and utilities user guide. Installing Software for Windows Server 2003 The HBA driver and applications kits for Windows Server 2003 OS is available for download at the Emulex support site for Oracle. To Install the Software for Windows Server 2003 Follow these steps to download the driver and AutoPilot installer: 1. Go to the Emulex support site for Oracle at: 2. Locate the driver section for Windows. 3. Download the Driver Kit by clicking the Download icon. 4. Click the PDF Manual icon to download installation guide for the Windows OS. 5. Install the driver and management utilities for the Windows OS as described in the installation guide. Chapter 3 HBA Software Installation 17

24 Configuration and Diagnostic Utilities Use the HBAnywhere Remote Management Utility or the lputil command-line interface (CLI) utility to configure the HBA. These utilities are available for Linux and Windows OS and provide support for the following functions: Discover local and remote hosts, host bus adapters (HBAs), targets, and LUNs Reset HBAs Set HBA driver parameters Update firmware Enable or disable the system BIOS Run diagnostic tests on HBAs Manage out-of-band HBAs Manage local and in-band remote HBAs See the Linux or Windows OS Emulex user manual for more information about using the HBAnywhere and lputil utilities. 18 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013

25 CHAPTER 4 Release Notes This chapter contains the latest supplementary information for the preceding chapters in this guide. This chapter contains the following topics: Oracle Solaris 10 for x64/x86 Operating Systems on page 19 Red Hat Enterprise Linux 4 and SUSE Linux Enterprise Server 9 Systems on page 19 Windows Server 2003 Operating System on page 20 Oracle Solaris 10 for x64/x86 Operating Systems There are no known issues or bugs related to the Oracle Solaris 10 for x64/x86 operating system. Red Hat Enterprise Linux 4 and SUSE Linux Enterprise Server 9 Systems See the Emulex driver manuals for any known issues with the Linux drivers. 19

26 Windows Server 2003 Operating System See the Emulex driver manuals for any known issues with the Windows OS drivers. 20 StorageTek 4 Gb FC Dual Port ExpressModule HBA From Emulex Installation Guide July 2013