MANUAL. Document Version 1.0/March LOGIClink

Transcription

1 MANUAL Document Version 1.0/March 2018 LOGIClink

2 MANUAL LOGICLINK // PAGE 2 Manual LOGIClink Rev 0 Document Version 1.0 from March 2018 The German language version is the original document. LOGICDATA Electronic & Software Entwicklungs GmbH Technical Documentation Wirtschaftspark Deutschlandsberg Austria Phone: +43 (0) Fax: +43 (0) Internet: documentation@logicdata.net

3 MANUAL LOGICLINK // PAGE 3 1 CONTENTS 1 About this document Copyright Trademarks 4 2 Safety General safety regulations and obligations Qualified persons Liability Symbols and signal words used 7 3 Product description Intended use Compatibility Suitable table tops 9 4 Unpacking 10 5 Installation Assembly System setup with standard cable System setup with retrofit cable 17 6 Operation Adjust table height Restart S0 reset / Restore factory settings 21 7 APP and API Using the API Bluetooth pairing 22 8 Maintenance 22 9 Troubleshooting Disassembly and disposal 23

4 MANUAL LOGICLINK // PAGE 4 1 ABOUT THIS DOCUMENT The product documentation consists of this manual and a data sheet. This document is intended to enable the assembly personnel to work safely with the products. The assembly personnel must therefore always have the complete documentation available. The document must be complete and in a perfectly legible condition. Follow the instructions in this document to avoid hazards and to prevent damage to the products. The information in this document has been compiled with great care. We strive to ensure the accuracy and completeness of the content by revising it and updating it regularly, however, no guarantee can be given its accuracy and completeness. If you have any problems or questions about the documentation, please contact our technical documentation department. 1.1 COPYRIGHT March 2018 by LOGICDATA Electronic und Software Entwicklungs GmbH All rights reserved. All information in this documentation is protected by copyright. No part of this documentation may be copied or reproduced without the written permission of LOGICDATA. LOGICDATA reserves the right to change specifications and other information in this documentation without prior notice. 1.2 TRADEMARKS Documentation may include, but is not limited to, the representation of registered trademarks of goods or services, as well as information about copyright or other proprietary expertise of LOGICDATA or third parties. In all cases, all rights remain exclusively with the respective copyright holder. LOGICDATA is a registered trademarks of the LOGICDATA Electronic und Software GmbH in the USA, the European Union and other countries.

5 MANUAL LOGICLINK // PAGE 5 2 SAFETY 2.1 GENERAL SAFETY REGULATIONS AND OBLIGATIONS In general, the following safety regulations and obligations apply when handling the product: The product may only be operated in a clean and perfect condition. Do not remove, change, bridge or bypass any protection, safety or monitoring equipment. Do not convert or modify the product without written approval from LOGICDATA. In the event of malfunction or damage, the product must be replaced immediately. Repairs are prohibited. Defective products are to be replaced as a whole. Hardware replacement or changes to the system configuration are only allowed in a de-energized state. Only qualified persons are allowed to work on the product. For the operation of the system, the national worker protection conditions and the national safety and accident prevention regulations apply. 2.2 QUALIFIED PERSONS Products from LOGICDATA may only be installed and commissioned by qualified persons who are authorized for installation planning, installation, commissioning or maintenance/servicing and who have read and understood the product documentation. Qualified persons have the necessary expertise to test, assess and manage electrical and mechatronic products and systems in accordance with the generally accepted standards and guidelines of electrical engineering and furniture manufacturing through their education, work experience and recent professional activity. They know and adhere to the basic regulations on occupational safety and accident prevention and the basic norms and specialist standards applicable to the specific application. All safety standards and guidelines relevant to the application must be taken into account. The furniture manufacturer performs a safety assessment of the entire system and is responsible for the certification of the entire system.

6 MANUAL LOGICLINK // PAGE LIABILITY The information in this documentation describes the properties of the products without guaranteeing them. The products satisfy current state of the art standards as well as the applicable health and safety regulations. Nevertheless, dangers can result from incorrect operation or misuse. LOGICDATA is not liable for damages caused by: Improper use of the products Disregard of the documentation Unauthorized changes to the products Improper work on and with the product Operation of a product, although it is damaged Wear parts Improperly performed repairs Unauthorized, improper change of operating parameters Disasters, external influence and force majeure Responsible for the LOGICDATA products in the specific application and compliance with the relevant directives, standards and laws is the manufacturer of the height-adjustable tables in which the LOGICDATA products are installed. LOGICDATA shall not be held liable for any damage that is directly or indirectly attributable to the delivery, performance or use of this document.

7 MANUAL LOGICLINK // PAGE SYMBOLS AND SIGNAL WORDS USED DANGER Warns of a dangerous situation. Disregard of the warning will result in death or serious personal injury. WARNING Warns of a dangerous situation. Disregard of the warning can result in serious personal injury. CAUTION Warns of a dangerous situation. Disregard of the warning can result in injury or property damage. NOTICE Information that facilitates the handling of the product or increases understanding. Warning of a source of danger Warning of electrical voltage Risk of injury due to pinching Damage due to electrostatic discharge (ESD) Use and storage only in dry indoor areas

8 MANUAL LOGICLINK // PAGE 8 3 PRODUCT DESCRIPTION LOGIClink is a connectivity hub for intelligent, electrically height-adjustable desks. The product is available in two variants Personal and Corporate. LOGIClink has a presence sensor, a status LED, control buttons for use as a hand switch, Bluetooth, NFC and USB. The Corporate version is also WiFi-enabled. 1 DOWN key 2 UP key 3 Presence sensor 4 Minifit 5 Restart button 6 Micro USB 7 NFC 8 WiFi (Corporate version only) Status LED 8 9 Fig. 1: Product overview 3.1 INTENDED USE LOGIClink is an electrical appliance for home use. It may only be used in dry indoor areas and according to the product description. The setup location must be level, vibration-free and free from dirt, dust, etc. Ensure that there is no excessive exposure to dust or toxic or corrosive gases and vapors or excessive heat at the setup location. This device may be used by children 8 years old and over, and by persons with reduced physical, sensory or mental abilities, or lack of experience and knowledge, if they are supervised or have been instructed in the safe use of the device and understand the resulting hazards. Do not allow children to play with the device. Do not allow children to perform the cleaning without supervision. After the mechatronic system has been built into a table, the table manufacturer is responsible for risk analysis and evaluation of the entire table and for creating the user documentation.

9 MANUAL LOGICLINK // PAGE COMPATIBILITY LOGIClink is compatible with the following products from LOGICDATA: Controllers Compact-e SMART-e SMARTneo The COMPACT-e+ and SMART-e+ controllers are not compatible and must never be connected. Hand switch (only allowed in conjunction with the RetroFit cable) TOUCHbasic-down TOUCHbasic-inlay TOUCHfx TOUCHinlay TOUCHdown 3.3 SUITABLE TABLE TOPS LOGIClink is suitable for table tops made of medium density fiberboard (MDF), high density fiberboard (HDF) or plywood. The thickness of the table top is a maximum of 31 mm, so that the NFC function can work trouble-free. All screws, cables or other metal parts must be at least 5 cm away from the LOGIClink.

10 MANUAL LOGICLINK // PAGE 10 4 UNPACKING Delivery scope LOGIClink is delivered to the customer in packaging units of at least 25 pieces. The products can be packed in plastic or cardboard. Mounting hardware or cables are not included. To unpack, proceed as follows 1. Put on a grounding wristband. CAUTION Ensure proper ESD handling during unpacking. Errors that can be attributed to electrostatic discharge will void warranty claims. 2. Remove the packaging material. 3. Check the contents of the package for completeness and damage. 4. Separate plastic and cardboard according to type. Dispose of the packaging material in an environmentally friendly manner.

11 MANUAL LOGICLINK // PAGE 11 5 INSTALLATION The table system may only be assembled by qualified persons. The workplace must be clean, dry and ESD-protected. CAUTION Pay attention to ESD-compliant handling. Errors that can be attributed to electrostatic discharge will void warranty claims. 5.1 ASSEMBLY You also need: Mounting screws suitable for your table top. The mounting opening consists of mounting holes with a diameter of 5 mm and a recess for the screw head of 11 mm. Pen for marking the drill holes Drill Screwdriver suitable for screwing in your mounting screws Procedure: 1. Mark the drill holes on the underside of the table top. Please note that the status LED on the front edge of the table is visible and that LOGIClink requires at least 5 cm clearance to metal parts and cables on all sides " 87,0 mm " 40,45 mm " 112,0 mm Fig. 2: Drill holes 2. Drill the holes as indicated in Fig Attach LOGIClink using the mounting screws.

12 MANUAL LOGICLINK // PAGE 12 NOTICE We recommend installing LOGIClink at a distance of approx. 70 cm from the user. Fig. 3: Mount LOGIClink 4. Align the presence sensor to the user. If LOGIClink is mounted to the left of the user, turn the presence sensor towards L. If LOGIClink is mounted to the right of the user, turn the presence sensor towards R. Fig. 4: Align presence sensor

13 MANUAL LOGICLINK // PAGE SYSTEM SETUP WITH STANDARD CABLE Use this system setup for the following configuration: LOGIClink is used as the only control element. No additional hand switch is connected. The type plate of the controller has Works with LOGIClink printed on it. Fig. 5: Standard cable The standard cable has 2 connectors: DIN (is plugged into the hand switch socket of the control) 10-pin minifit (LOGIClink) Fig. 6: Standard cable LOG-CBL-LOGICLINK-CB-STANDARD

14 MANUAL LOGICLINK // PAGE 14 System overview Fig. 7: Standard configuration Assemble system 1. Plug the minifit plug of the standard cable into the LOGIClink. Fig. 8: Plug minifit into LOGIClink 2. Lay and secure the cable along the table to the controller. 3. Connect the blue DIN plug to the controller's hand switch socket (marked *HS* on the housing).

15 MANUAL LOGICLINK // PAGE 15 Fig. 9: Connection to COMPACT controller Fig. 10: Connection to SMART controller Fig. 11: Connection to SMARTneo controller 4. Plug the mains cable into the controller. 5. Finally, plug the mains cable into the power outlet.

16 MANUAL LOGICLINK // PAGE Mark the NFC reading surface on the top of the table, for example with an adhesive film. The reading area is 6 6 cm and is located in the center, one centimeter from the rear edge above the connectivity hub. The marking must not contain any metals. Fig. 12: Mark the NFC reading area

17 MANUAL LOGICLINK // PAGE SYSTEM SETUP WITH RETROFIT CABLE Use this system setup if one of the following conditions applies: Additional hand switch can be connected. The COMPACT-e or SMART-e controller was produced before April 2017 and is therefore not compatible as delivered from the factory. Retrofit cable The retrofit cable has 4 connectors: DIN male (is plugged into the hand switch socket of the control) DIN female (connector for additional, optional hand switch) 10-pin minifit (LOGIClink) USB (external power supply, not available from LOGICDATA) Fig. 13: Retrofit cable LOG-CBL-LOGICLINK-CB-RETROFIT

18 MANUAL LOGICLINK // PAGE 18 System overview Fig. 14: Retrofit configuration with additional hand switch Assemble system 1. Plug the minifit plug of the standard cable into the LOGIClink. Fig. 15: Plug minifit into LOGIClink 2. Lay and secure the cable along the table to the controller. 3. Connect the blue DIN plug to the controller's hand switch socket (marked *HS* on the housing).

19 MANUAL LOGICLINK // PAGE 19 Fig. 16: Connection to COMPACT controller Fig. 17: Connection to SMART controller 4. Connect the plug of the hand switch to the blue DIN-female plug of the retrofit cable. 5. Plug an external power adapter into the USB connector. Fig. 18: Connect external power supply to the USB connector 6. Plug the external power adapter into the power outlet. 7. Mark the NFC reading surface on the top of the table, for example with an adhesive film. The reading area is 6 6 cm and is located in the center, one centimeter from the rear edge above the connectivity hub. The marking must not contain any metals.

20 MANUAL LOGICLINK // PAGE 20 Fig. 19: Mark the NFC reading area

21 MANUAL LOGICLINK // PAGE 21 6 OPERATION 6.1 ADJUST TABLE HEIGHT Press the UP or DOWN button on the bottom of LOGIClink to adjust the table height. 6.2 RESTART To restart LOGIClink, press and hold the restart button for 5 seconds. 6.3 S0 RESET / RESTORE FACTORY SETTINGS The S0 reset resets the table system to factory settings. All individual settings are deleted. 1. Disconnect the power supply to the desk by unplugging the power plug. 2. Press the UP and DOWN buttons at the same time and keep both buttons pressed. 3. Plug the power plug back into the socket. The LOGIClink flashes to indicate when the reset window is open. 4. Release the UP and DOWN buttons before the LOGIClink stops blinking, indicating the end of the reset time window. 5. If you allow the reset time window to elapse (timeout), the table system will not be reset to factory settings. In this case, begin the procedure again at step 1.

22 MANUAL LOGICLINK // PAGE 22 7 APP AND API The LOGIClink motion@work app (available in the Apple App Store and Google Play Store) stores personal workplace settings to they are immediately available after a table change. The app can track how much time the user spends sitting and standing. This permits personal recommendations to be derived from this, for example. Optionally, LOGIClink also includes a programming interface (API) to help you develop apps for your visions. 7.1 USING THE API The LOGIClink API allows you to tailor your custom applications for specific end-uses. Contact your LOGICDATA customer contact to obtain the API download. 7.2 BLUETOOTH PAIRING 1. Download the motion@work app for free from the Play Store or App Store. Google/Android: Play Store Apple/iOS: App Store 2. Double-click the restart button on the LOGIClink to start Bluetooth pairing. The status LED of LOGIClink flashes green quickly. LOGIClink will be displayed on your smart device with the available Bluetooth devices. The pairing indicator has a timeout of 30 seconds. If you do not start pairing during this time, the display goes out. Double-click the restart button to start pairing. 3. Enter the pairing data. If the pairing was successful, the status LED flashes red twice in succession. 8 MAINTENANCE The LOGIClink control element is maintenance-free for its entire service life. If cleaning is necessary, wipe off LOGIClink with a soft, dry cloth.

23 MANUAL LOGICLINK // PAGE 23 9 TROUBLESHOOTING Most errors can be remedied by restarting. Restart To restart LOGIClink, press and hold the restart button for 5 seconds. Contacting support For technical problems, please contract our support at: Tel.: +43 (0) Fax: +43 (0) office.at@logicdata.net Always provide the product name and the revision status according to the type plate with any support request. In case of a defect, replace LOGIClink as a whole. 10 DISASSEMBLY AND DISPOSAL How to disassemble LOGIClink 1. Disconnect the power supply of the table. 2. Disconnect all cables. 3. Unscrew the three mounting screws that attach LOGIClink to the table top. 4. Dispose of all parts in course of the final decommissioning in an environmentally sound and unmixed manner. Disposal The LOGIClink is an electrical and electronic device that must be disposed of separately from household waste according to the WEEE Directive 2012/19/EU. The products are marked with the symbol shown on the left. Before disposing of materials and components, check their recyclability. Recycle as many parts as possible. Dispose of all materials and parts in accordance with your local guidelines and regulations. Ensure that the disposal is lastingly compatible for humans and nature.

24 LOGICDATA Electronic & Software Entwicklungs GmbH Wirtschaftspark Deutschlandsberg Austria LOGICDATA North America, Inc Gezon Parkway SW, Suite C Grand Rapids, MI USA Phone: +43 (0) Fax: +43 (0) office.at@logicdata.net Phone: +1 (616) office.na@logicdata.net